1 6556 pulses per revolution programmable Features Size mm Precise optical sensing Output signal level programmable (TTL or HTL) Clamping or synchro flange Connection axial, radial or tangential Pulses per revolution 1...6556, programmable High protection up to IP 67 High resistance to shock and vibrations EIL580P with clamping flange Technical data - electrical ratings Voltage supply Reverse polarity protection Yes Short-circuit proof Consumption w/o load Initializing time.75...0 VDC Yes 70 ma Pulses per revolution 1...6556 Scan ratio 0 ms after power on 5...55 % typical at 8 ppr Reference signal Zero pulse 90 or 180 Sensing method Optical Output frequency 00 khz (TTL) 160 khz (HTL) Output signals A+, B+, R+, A-, B-, R- Output stages TTL/RS22 HTL/push-pull Programmable parameters Output level TTL/HTL Pulse number 1...6556 Zero pulse width 90 /180 Zero pulse position Signal sequence Interference immunity DIN EN 600-6-2 Emitted interference DIN EN 600-6- Approval UL 508 / CSA 22.2 Technical data - mechanical design Size (flange) Shaft loading Protection DIN EN 60529 mm 0 N axial 80 N radial IP 65 (without shaft seal), IP 67 (with shaft seal) Operating speed 6000 rpm (+ C, IP 67) 100 rpm (+ C, IP 65) Starting torque 0.01 Nm (+ C, IP 65) 0.02 Nm (+ C, IP 67) Materials Housing: aluminium die-cast Flange: aluminium Solid shaft: stainless steel Operating temperature -0...+0 C Relative humidity 90 % non-condensing Resistance DIN EN 60068-2-6 Vibration 0 g, -00 Hz DIN EN 60068-2-27 Shock 00 g, 6 ms Connection Flange connector M12, 8-pin Flange connector M2, 12-pin Cable Weight approx. 00 g EIL580P - clamping flange Shaft type ø x mm, solid shaft with edge (clamping flange) EIL580P - synchro flange Shaft type ø6 x mm, solid shaft with flat edge (synchro flange) 1
1 6556 pulses per revolution programmable Part number Clamping flange EIL580P-S C. F. 02. B Operating temperature B -0...+0 C Pulses programmable 02 1...6556 programmable (factory setting: 2) F Voltage supply / output stages.75...0 VDC, TTL/RS22, 6 channels (Vout = 5 VDC) - Factory setting HTL/push pull 6 channel (Vout = Vin) - programmable by customer Connection R Cable radial, 1 m L Cable radial, 2 m F Flange connector M2, 12-pin, radial, male, ccw B Flange connector M12, 8-pin, radial, male, ccw T Cable axial, 1 m U Cable axial, 2 m D Flange connector M2, 12-pin, axial, male, ccw A Flange connector M12, 8-pin, axial, male, ccw P Cable tangential, 1 m * Q Cable tangential, 2 m * Protection 5 IP 65 7 IP 67 Specification solid shaft ø x mm, with edge C Flange Clamping flange, centering collar ø6 mm, M/M Printed in bold = standard items (up to the quantity of will be supplied within 5 working days). * only available in protection 5 = IP 65 (Factory setting: 2 ppr, Vout = 5 VDC TTL, signal sequence A leading B (CW), zero pulse 90 A&B high) Stock items EIL580P-SC.5FF.02.B EIL580P-SC.5RF.02.B Numerous stock items in single quantity will be supplied within 2 hours respectively one day ex works. 2
1 6556 pulses per revolution programmable Part number Synchro flange EIL580P-S Y 06. F. 02. B Operating temperature B -0...+0 C Pulses programmable 02 1...6556 programmable (factory setting: 2) F Voltage supply / output stages.75...0 VDC, TTL/RS22, 6 channels (Vout = 5 VDC) - Factory setting HTL/push pull 6 channel (Vout = Vin) - programmable by customer Connection R Cable radial, 1 m L Cable radial, 2 m F Flange connector M2, 12-pin, radial, male, ccw B Flange connector M12, 8-pin, radial, male, ccw T Cable axial, 1 m U Cable axial, 2 m D Flange connector M2, 12-pin, axial, male, ccw A Flange connector M12, 8-pin, axial, male, ccw P Cable tangential, 1 m * Q Cable tangential, 2 m * Protection 5 IP 65 7 IP 67 Specification solid shaft 06 ø6 x mm, with edge Y Flange Synchro flange, flute ø5 mm, M/M Printed in bold = standard items (up to the quantity of will be supplied within 5 working days). * only available in protection 5 = IP 65 (Factory setting: 2 ppr, Vout = 5 VDC TTL, signal sequence A leading B (CW), zero pulse 90 A&B high) Stock items EIL580P-SY06.5FF.02.B EIL580P-SY06.5RF.02.B Numerous stock items in single quantity will be supplied within 2 hours respectively one day ex works.
1 6556 pulses per revolution programmable Accessories Connectors and cables 1278 Connection cable 2 m shielded with female connector M12, 8-pin, straight (ESG FH00G) 1292 Connection cable 5 m shielded with female connector M12, 8-pin, straight (ESG FH0500G) 129 Connection cable m shielded with female connector M12, 8-pin, straight (ESG FH00G) 961 Connection cable 2 m shielded with female connector M12, 8-pin, angled (ESW FH00G) 962 Connection cable 5 m shielded with female connector M12, 8-pin, angled (ESW FH0500G) 17005 Connection cable m shielded with female connector M12, 8-pin, angled (ESW FH00G) 16705 Connector M2, 12-pin 19502 Connection cable 1 m shielded with female connector M2, 12-pin 11008 Connection cable 2 m shielded with female connector M2, 12-pin 1100 Connection cable 5 m shielded with female connector M2, 12-pin 1101 Connection cable m shielded with female connector M2, 12-pin 11119280 Connection cable connector M12 / connector D-SUB, 0.2 m 111197 Connection cable connector M12 / connector D-SUB, 1 m 11119257 Connection cable connector M2 / connector D-SUB, 0.2 m (S2BG12/KSG9) 1111972 Connection cable connector M2 / connector D-SUB, 1 m (S2BG12/KSG9) Mounting accessories for EIL580P - clamping flange 1659 Coupling CPS25 L=19 d1=0/d2= 165918 Coupling CPS25 L=19 d1=07/d2= 1659 Coupling CPS25 L=19 d1=08/d2= 165921 Coupling CPS25 L=19 d1=09/d2= 165922 Coupling CPS25 L=19 d1=/d2=06 16592 Coupling CPS25 L=19 d1=/d2= 16592 Coupling CPS25 L=19 d1=/d2=11 165925 Coupling CPS25 L=19 d1=/d2=12 1112 Spring washer coupling D1=06 / D2= 111 Spring washer coupling D1= / D2= 118 Spring washer coupling D1= / D2=16 110 Spring washer coupling D1= / D2=1 Accessories Mounting accessories for EIL580P - clamping flange 111 Spring washer coupling D1= / D2=12 0507 Bellows coupling aluminium/stainless steel D1=06 / D2= 111781 Double loops coupling D1= / D2= 125051 Mounting adaptor for encoders with clamping flange 16555 Set of eccentric fixings type A 11189 Tether arm Mounting accessories for EIL580P - synchro flange 165916 Coupling CPS25 L=19 d1=06/d2=06 165917 Coupling CPS25 L=19 d1=06/d2=08 165922 Coupling CPS25 L=19 d1=/d2=06 165926 Coupling CPS25 L=19 d1=11/d2=06 165928 Coupling CPS25 L=19 d1=12/d2=06 1111 Spring washer coupling D1=06 / D2=06 1112 Spring washer coupling D1=06 / D2= 119 Spring washer coupling D1=06 / D2=16 0507 Bellows coupling aluminium/stainless steel D1=06 / D2= 117667 Mounting adaptor for encoders with synchro flange 117668 Set of eccentric fixings for mounting clamp (117667): x eccentric fixings, screws and nuts 16555 Set of eccentric fixings type A 812 Bearing flange for encoders with synchro flange (Z ) Programming accessories 111657 Handheld Programming Tool Z-PA-EI-H 11157 PC Programming Tool Z-PA-EI-P Matching measuring wheels available as accessories, see under measuring wheels (MR).
1 6556 pulses per revolution programmable Output signals A+ A- B+ B- R+ R- A+ A- Zero pulse electrical 90 A&B high (Factory setting at clockwise rotation (CW) in view of the encoder flange) 90 90 Zero pulse electrical 180 B low (at clockwise rotation (CW) in view of the encoder flange) Terminal assignment Flange connector M2, 12-pin / cable Pin Core color Assignment 1 pink B- 2 blue R+ red R- 5 green A+ 6 yellow A- 7 R-Teach 1) 8 grey B+ 9 white GND 11 12 brown UB Screen: Connected to housing Cable data: PUR, [x2x0,1 mm 2 ], bending radius >5,8 mm, outer diameter 6.1 mm 2 1 9 11 8 12 5 7 6 1) The R-Teach input is used to set the reference pulse (zero pulse) on the current shaft position. R-Teach = UB 0 ms B+ B- R+ R- Trigger level Outputs Output level High Output level Low Load Outputs Output level High Output level Low Load 90 180 TTL/RS22 2.5 V 0.5 V ma HTL/Push-pull UB - V 1.5 V ma Flange connector M12, 8-pin Pin Assignment 1 GND 2 UB A+ A- 5 B+ 6 B- 7 R+ 8 R- 7 6 1 2 8 5 5
1 6556 pulses per revolution programmable Dimensions Clamping flange, flange connector M12, radial 8 ø8±0.2 51. 11.8 M12x1 øg7 ø6h8 ø5±0.05 Clamping flange, flange connector M2, radial 8 56 øg7 ø6h8 ø5±0.05 ø8±0.2 1. M2x1 Clamping flange, cable radial ø8±0.2 ~5 8 11.8 øg7 ø6h8 ø5±0.05 6
1 6556 pulses per revolution programmable Dimensions Clamping flange, flange connector M12, axial 21.8 8 ø8±0.2 M12x1 øg7 ø6h8 ø5±0.05 11.1 Clamping flange, flange connector M2, axial 26.5 8 ø8±0.2 M2x1 øg7 ø6h8 ø5±0.05 8.5 Clamping flange, cable axial ~2 8 ø8±0.2 øg7 ø6h8 ø5±0.05 11.1 7
1 6556 pulses per revolution programmable Dimensions Clamping flange, cable tangential 8.5 128 ø8±0.2 5 øg9 ø6h8 ø5±0.05 Synchro flange, flange connector M12, radial 51. ø5±0.05 ø2±0.2 M12x1 11.8 Synchro flange, flange connector M2, radial ø2±0.2 56 1. M2x1 ø5±0.05 8
1 6556 pulses per revolution programmable Dimensions Synchro flange, cable radial ~5 ø5±0.05 ø2±0.2 11.8 Synchro flange, flange connector M12, axial 21.9 ø2±0.2 M12x1 ø5±0.05 11.1 Synchro flange, flange connector M2, axial ø2±0.2 M2x1 26. ø5±0.05 8.5 9
1 6556 pulses per revolution programmable Dimensions Synchro flange, cable axial ~2 ø2±0.2 ø5±0.05 Synchro flange, cable tangential.5 ø2±0.2 5 128 11.1 ø5-0.05