Series 1 Centrifugal Pumps B-207H
Table of Contents Useful Pump Formulas... 2 Standard Features... 3 Technical Data... Materials of Construction... Selection Charts... 6 Performance Curves... 7 Centrifugal Pump Dimensions... 8-9 The B&G End Suction Pump System... Typical Specifications... 11 Useful Pump Formulas Pressure = Head (Feet) x Specific Gravity (PSI) 2.31 Head Pressure (PSI) x 2.31 = (Feet) Specific Gravity Vacuum Dynamic Suction Lift (Feet) x.883 = (Inches of Mercury) x Specific Gravity Horsepower GPM x Head (Feet) x Specific Gravity = (Brake) 3960 x Pump Efficiency Horsepower = GPM x Head (Feet) x Specific Gravity (Water) 3960 Efficiency = (Pump) NPSH = (Available) Horsepower (Water) x 0 Per Cent Horsepower (Brake) Positive Factors Negative Factors Affinity Laws: Effect of change of speed or impeller diameter on centrifugal pumps. Impeller Diameter Change GPM Capacity Ft. Head BHP Q2 = D2 Q1 D1 H2 = ( D2 D1) 2 H1 P2 = ( D2 D1) 3 P1 Speed Change Q2 = RPM2 Q1 RPM1 H2 = ( RPM2 RPM1) 2 H1 P2 = ( RPM2 RPM1) 3 P1 Where Q = GPM, H = Head, P = BHP, D = Impeller Dia., RPM = Pump Speed 2
Take away these eight standard features and you ll have a pump like everyone else s. True Back Pullout A B&G standard in design and construction.ease in service is assured, while piping and motor remain undisturbed. Extended delays for repairs are virtually eliminated. Internally Self-Flushing Mechanical Seal This design is way ahead of its time. This unique seal design is proven in many years of service. It requires no special external flushing provisions, since the design provides for constant efficient flushing action internally. This standard feature ensures maximum seal face lubrication, heat dissipation and debris removal without vulnerable, external flush tubing. The internal flushing action passes two and a half to three times the flow over the seal faces compared to a few GPM for conventional, stuffing-box designed pumps. Computer Controlled Impeller Balancing 1 impellers are balanced to ANSI/HI 9.6.-2009, balance grade G6.3 standards. This method of computer balancing Impellers provides for quiet, efficient, vibration free performance. Diameters are computer selected at the factory to furnish assurance that your capacity requirements will be met. Solid-Foot Mounted Volute All Series 1 pumps are provided as standard with an integrally cast volute foot located directly beneath the pump volute. This integrally cast foot ensures that the alignment between the volute and motor assembly is maintained. Without solid support beneath the volute, the piping weight alone will cause distortion which can lead to premature failure of the bearings, shaft and mechanical seal. This feature is equally important on hot water applications. The Series 1 volute foot provides a solid foundation and eliminates the deflections which would otherwise exist within an unsupported overhung volute during the normal thermal expansion of the system piping against the volute. Center Drop-Out Spacer Coupling Unlike conventional jaw type or rigid style couplings, a center drop-out spacer coupling allows removal of the bearing frame and rotating element without disturbing the pump end pipe alignment or motor electrical connections. ANSI/OSHA-Compliant Coupling Guard The coupler guard complies with ANSI B1.1 and OSHA 19.219. The guard offers increased protection against potential injuries and is standard on all 1 pumps. The guards include slotted viewing windows for easy inspection. Heavy Duty, Rugged Baseplate The Bell & Gossett fabricated heavy duty baseplate is supplied as standard on every Series 1 pump. Unlike rolled steel and C channel baseplates, the Series 1 baseplate provides a heavy duty saddle assembly, full seam welds, closed baseplate ends and an open top to provide ease of access for proper equipment grouting. Patented i-alert TM Condition Monitor Continuously measures vibration and temperature at the outboard bearing and automatically indicates when pre-set levels of vibration and temperature have been exceeded, so that changes can be made before failure occurs. A visual indication of pump health makes walk-around inspections more efficient and accurate. This onboard pump intelligence helps minimize life-cycle costs while maximizing performance. 3
Technical Data BALANCE STANDARDS Impellers are balanced to Hydraulic Institute Standards ANSI/HI 9.6.-2009. The allowable residual unbalance in the impeller rotating assembly conforms to ANSI grade G6.3 (Ref. ISO 190). ANSI Balance Quality Grades of G2. and G1 for the rotating assembly are also available. Consult your local Bell & Gossett Representative for additional details. VIBRATION LIMITS Series 1 pumps conform to Hydraulic Institute ANSI/HI 9.6.-2009 for recommended acceptable unfiltered field vibration limits (as measured at the pump bearings per ANSI/HI 9.6.-2009, Figure 9.6..2.3.1) for pumps with rolling contact bearings. OVERALL DISPLACEMENT (Unfiltered) PUMP SPEED RPM Peak to Peak-Mils (.001 ) 3600 2.2 1800 3.8 1200.8 SEISMIC CAPABILITIES Series 1 pumps are capable of withstanding a horizontal load of 0.g* without adversely affecting pump operation. *Piping and/or fasteners used to anchor the pump to the mounting pads on the floor are excluded. MECHANICAL SEAL Seal Features Standard Seal Type Internally Flushed Seal Enlarged Seal Chamber Standard Seal Construction Standard Working Pressure Maximum Working Pressure Standard Seal Temperature Rating Optional Temperature Rating B&G Yes Yes Buna-Carbon-Ceramic 17 psig (12 Bar) 20 psig (17 Bar) 22 deg F (7 C) 20 deg F (121 C) The ceramic material is 99.% pure alumina oxide, ceramic seat hardness of 68 Rockwell C, or a tensile strength of 300,000 psi.
Materials of Construction 1 Shaft 9 Condition Monitor 11 Gauge Tapping Volute Gasket Seal Assembly Vent Plug 2 Volute 3 Impeller Gauge Tapping Bronze Casing Wearing Ring (Optional) Gauge Tapping Lantern Ring Packing 11 Condition Monitor Packing Gland 1 Shaft 9 Volute Gasket 2 Volute 3 Impeller Gauge Tapping Bronze Casing Wearing Ring (Optional) Slinger Slinger Shaft Sleeve Impeller Key 6 Impeller Washer 7 Impeller Lock Washer Impeller Cap Screw Shaft Sleeve Impeller Key 6 Impeller Washer 7 Impeller Lock Washer Impeller Cap Screw Drain Plug DESCRIPTION BRONZE FITTED PUMP (STANDARD CONFIGURATION ALL IRON PUMP (OPTIONAL) 11 Shaft Steel SAE 11 Steel SAE 11 12 Volute Cast Iron Cast Iron ASTM #A19 ASTM #A19 13 Impeller Cast Bronze Cast Iron ASTM #B8 ASTM #A36 1 Shaft Sleeve Bismuth Bronze #30 Stainless Steel #C8983 ASTM #A312 1 Impeller Key #30 Stainless Steel #30 Stainless Steel Impeller Washer 1 Steel Stainless Steel 17 Impeller Lock Washer #30 Stainless Steel #30 Stainless Steel 18 Impeller Cap Screw #30 Stainless Steel #30 Stainless Steel 19 Volute Gasket Cellulose Fiber Cellulose Fiber Seal Assemblies 11 Condition Monitor Stainless Steel Encloser Stainless Steel Encloser Standard Seal Standard Configuration Bellows Buna N Buna N Faces Carbon-Ceramic Carbon-Ceramic Metal Parts Brass Stainless Steel Spring Stainless Steel Stainless Steel For Stuffing Box A Flushed Single O-Rings EPR EPR Faces Carbon-Tungsten Carbon-Tungsten Carbide Carbide Metal Parts Stainless Steel Stainless Steel Spring Stainless Steel Stainless Steel Packed Packing Graphited Graphited Impregnated Teflon Impregnated Teflon Gland Bronze Cast Iron Lantern Ring Filled TFE Filled TFE ** For operating temperatures above 20 F, a cooled flush is required and is recommended for temperatures above 22 F for optimum seal life. On closed systems, cooling is accomplished by inserting a small heat exchanger in the flush line to cool the fluid. Flush-line Filters and Sediment Separators are available on special request. Optional S Configuration OPTIONAL FEATURES All Iron Construction Bronze Casing Wear Ring Stainless Steel Shaft Sleeve Stainless Steel Shaft Drip Pan EPR/Tungsten Carbide Seal (Standard Configuration only) Stuffing Box Construction with several seal and packing options Seal Selection Guide For: A. Standard Seals BUNA-PH Limitations 7-9; Temperature Range 20 F to +22 F EPR-PH Limitations 7-11; Temperature Range 20 F to +20 F For use on open or closed clear water systems. Maximum working pressure 17 psi. B. Flushed Single Seals (Stuffing Box Design) PH Limitations 7-11; Temperature Range 20 F to +300 F** For use on closed or open systems where the temperature or pressure requirements exceed the limitations of the standard seal. Available in 17 psi, or 20 psi working pressures. C. Flushed double Seals (Stuffing Box Design) PH Limitations 7-9; Temperature Range 0 F to +20 F For use on closed or open low pressure systems which may contain a high concentration of abrasives.an external flush is required. Maximum working pressure 17 psi. D. Packing (Stuffing Box Design) PH Limitations 7-9; Temperature Range 0 F to +190 F For use on open or closed systems which require a large amount of make-up water, as well as systems which are subjected to widely varying chemical conditions and solids buildup.
Selection Charts 20 30 90 0 60 7080 0 0 200 300 800 900 00 00 600700 00 2000 3000 000 000 60 Hz 00 00 300 200 300 RPM TOTAL HEAD, ft. of water 0 90 80 70 60 0 0 30 20 170 RPM 1 RPM 20 30 90 0 60 7080 0 0 200 300 800 900 00 00 600700 00 2000 3000 000 000 CAPACITY, gpm 0 Hz 6
Series 1 Performance Curves 170 RPM 60 20 300 RPM 80 0 00 360 TOTAL HEAD, FEET 320 280 20 200 0 120 80 0 00 0 200 20 300 00 0 00 30 00 0 2000 200 CAPACITY IN U.S. GALLONS PER MINUTE 7
Series 1 Centrifugal Pumps Dimensions DISCHARGE SUCTION Motor Horsepower and Frame Tabulation three phase (Dripproof Enclosure) Z HA HO HD Y HL HP GAUGE TAPPINGS* HB Frame @ Frame @ Frame @ Frame @ Horsepower 170 RPM 300 RPM Horsepower 170 RPM 300 RPM. 1 /2 6 20 26T 2T. 3 6 2 28T 26T 1. 13T 30 286T 28TS 1. 1 /2 1T 0 32T 286TS 2. 1T 1T 0 326T 32TS 3. 182T 1T 60 36T 326TS. 18T 182T 7 36T 36TS 7. 1 /2 213T 18T 0 0TS 36TS. 21T 213T 12 0TS 1. 2T 21T *Gauge Tapping Sizes: 1 for NPT, 1 for flanged sizes STANDARD MECHANICAL SEAL STUFFING BOX CONSTRUCTION DIMENSIONS INCHES (MM) PUMP MODEL 1, 1-F PUMP MODEL 1-PF, 1-S PUMP SIZE SUCTION MOTOR FRAME DISCHARGE SIZE SIZE HA HB HD HL HO HP Y Z HA HB HD HL HO HP Y Z 6 12 28 3 3 1 1 1 AC 13T-1T (30) (730) 9 (79) 3 3 1 3 1 /2 9 3 1 3 1 3 1 /2 (879) (NPT) 182T-18T 31(787) (28) 1 (37) 3 (11) 1 (28) () (37) 3 (11) 1 1 /2 213T-21T 3 (879) (6) 3 (371) 39 3 (00) (76) 3 1 1 (76) (NPT) 13T-1T 3 1 31 3 3 1 13 / 18 (83) 3 (371) 1 1 BC 182T-18T (787) 3 1 13 / 18 (83) 3 (879) (273) (6) (76) (273) (6) (76) (NPT) 213T-21T 39 3 (00) 1 /2 6 1 /2(1181) /2 12 20 2T-26T 6 1 /2 12(30) 2 1 / 20(08) () 1 (30) 2 1 3 / (08) () (06) (7) 28TS-286TS (06) (1181) 13(330) (7) 21(33) (131) 13(330) 21(33) 6 12 28 3 3 1 / 1 1 /2 AC 13T-1T (30) (730) 9 (78) 3 3 1 3 1 9 3 1 11 / 1 3 3 (879) (NPT) 182T-18T 31(787) (28) (00) (117) (371) (28) (3) (00) (76) (117) 213T-21T 3 (879) 39 3 (00) 2T-26T 39 3 (00) 3 (2) 3 (06) 6 1 /2(1181) 12(30) 2 13 /(71) 18(7) 2 13T-1T 1 31 1 (76) 11 / 3 1 3 3 1 (NPT) 182T-18T (371) (787) (3) 17 (79) 1 1 (879) 3 1 11 / 17 1 3 (79) (273) (371) (273) (3) (38) (76) 1 1 /2 BC 213T-170 3 (879) (38) 3 39 3 (00) 3 (NPT) 213T-21T-300 39 3 (00) () 6 1 /2(1181) 12 18 1 /2 () 2T-26T 6 1 /2 12(30) 2 13 / 181 /2(70) 1 (30) 2 13 3 / (70) (06) (71) 28TS-286TS (06) (1181) 13(330) (71) 19 1 /2(9) (131) 13(330) 19 1 /2(9) 2 AC 6 12 28 3 3 9 / 1 3 9 3 2 3 / 1 3 13T-1T (30) (730) 9 (90) 3 1 (371) (879) (28) (6) (13) (76) 182T-18T 31(787) (28) (13) 3 1 /2 3 3 1 /2 3 2 (89) (121) (89) (121) 213T-21T 3 (879) / 3 6 1 /2(1181) 11(279) 3 / 17 1 /2() (6) 2T-26T 39 3 (00) 17 1 (38) (76) (06) 1 3 (131) 12(30) (8) 18 1 /2(70) 1 2 1 /2 13T-1T 31 3 (371) 182T-18T (787) 3 2 11 / 1 17 3 (879) 3 2 11 / 17 3 3 (273) (68) (371) (273) (68) (1) (76) 213T-21T-170 3 (879) (1) 39 3 (00) 2 BC 2T-300 39 3 (00) 6 1 /2(1181) (2) (19) 12 19 (2) (19) 2T-26T 12(30) 3 13 / 19(83) (30) 3 (83) 13 / 28TS-286TS 6 1 /2 13(330) (97) 20(08) 1 3 (1181) (131) 13(330) (97) 20(08) 32TS-326TS 12(30) 19(83) 12(30) 19(83) 182T 18T 2 213T 6 1 /2 (06) 2 1 6 1 /2 (06) (73) () (73) () 21T 1 22 1 22 6 1 /2 2 E 2T (36) (9) (36) (9) () 6 1 286TS 6 1 /2(1181) () 32TS 1 3 1 3 1 1 1 /2 /2 () (131) () () 326TS (131) () 36TS 2 6 1 /2 3 2 1 /2 6 2 6 1 /2 3 2 1 /2 6 36TS (6) (122) (19) (121) (622) (12) (6) (122) (19) (121) (622) (12) 2 G 3 213T-21T 6 1 /2 6 1 /2(1181) 2T-26T (1181) 1 3 7 23 7 1 1 3 7 1 3 23 7 1 (06) (36) (98) (8) (18) (06) (36) (98) (8) (18) 28T 1 3 (131) (131) 6 12 28 3 3 13T-1T (30) (730) 9 (111) 1 3 1 3 3 9 3 3 1 3 3 2 1 /2 AB 182T-18T 31(787) (28) (00) 1 (371) (879) (28) (76) (00) (76) 11 / 1 11 / 3 3 (8) (119) (8) (119) 213T-21T 3 (879) 6 1 /2(1181) 11(279) 1 17 1 (76) (76) 2T-26T 39 3 (00) 3 (2) (06) 1 3 (131) 12(30) () (32) (371) 182T-18T 31(787) 2 3 17 1 /2 1 3 (879) 3 2 3 17 1 /2 (273) 3 213T-21T 3 (879) (70) () (371) 39 3 (00) (273) (70) () (76) 6 6 2 1 /2 BB 28TS-286TS 6 1 /2 13(330) 19 3 (02) 13(330) 19 3 (02) 32TS-326TS (1181) 3 12(30) (2) (12) 1 18 3 (76) 3 12(30) (2) (12) 18 3 (76) (06) (98) (06) (131) (98) 36TS 1 3 (131) 13(330) 19 3 (02) 13(330) 19 3 (02) 3 AC 13T-1T 12(30) 28 3 (730) /(1) 1 3 9 3 2 1 / 1 3 3 9 182T-18T 1 31(787) 1 3 2 1 3 (371) (879) (28) (7) (00) (76) / (28) (00) (76) 21T (371) 39 3 (00) (7) 1 6 1 /2(1181) 11(279) 17(32) () 2T-26T 6 1 /2 12(30) 1 / 18(7) 1 3 12(30) / () 18(7) (06) (3) 28TS-286TS (06) (1181) 13(330) (3) 19(83) (131) 13(330) 19(83) These dimensions are not to be used for installation purposes unless certified. 20 psi (17 bar) available Maximum Working Pressure 17 psi (12 bar) 8
Series 1 Centrifugal Pumps cont. d STANDARD MECHANICAL SEAL STUFFING BOX CONSTRUCTION DIMENSIONS INCHES (MM) PUMP MODEL 1, 1-F PUMP MODEL 1-PF, 1-S PUMP SIZE SUCTION MOTOR FRAME DISCHARGE SIZE SIZE HA HB HD HL HO HP Y Z HA HB HD HL HO HP Y Z 182T-18T 31(787) 1 3 (879) 3 3 11 / 18 1 3 1 213T-21T 3 (870) 3 11 / 18 1 3 (371) 39 3 (00) (273) (9) (6) (76) 3 BC (371) (273) (9) (6) (76) 2T 39 3 (00) 6 1 6 1 /2(1181) 12(30) 19 1 /2(9) 6 1 (121) () 28TS-286TS 6 1 /2 13(330) 13 / 20 1 /2(21) 1 3 13(330) / (121) () 20 1 /2(21) (06) (122) 32TS-326TS (1181) 12(30) (122) 19 1 /2(9) (131) 12(30) 19 1 /2(9) 18T 3 E 2 213T-21T 6 11 / 2 1 6 11 / (06) (73) 1 (170) 23 2T /2 (73) 1 (170) 23 1 /2 (36) (97) 26T 6 1 /2(1181) /2 7 (06) (36) (97) 3 1 / 1 3 /2 7 3 / () (187) () (187) 326TS 1 3 (131) (1) (131) (1) 36TS-36TS 2 6 1 /2 1 / 26 6 2 6 1 /2 1 / 26 6 0TS (6) (122) (19) (12) (660) (12) (6) (122) (19) (12) (660) (12) 213T-21T 6 1 /2 6 1 /2(1181) 2T-26T (1181) 1 3 G 23 1 /2 8 1 1 23 1 /2 8 28T-286T (06) 1 (36) () (97) (13) (203) (06) 1 3 3 (36) () (97) (13) (203) (131) 32T (131) 1T 31 1 3 182T-18T 1 (787) 3 / 18 1 3 (371) (879) 3 / 18 1 3 (273) (1) (6) (76) 213T (371) 3 (870) (273) (1) (6) (76) 39 3 (00) AC 21T 39 3 (00) / 3 6 1 /2(1181) 12 19 1 / 3 /2 (12) () (12) () 2T-26T 12(30) 19 1 /2(9) (30) (9) 7 / 6 28TS-286TS /2 13(330) / 1 20 1 /2(21) 13(330) (138) 20 1 /2(21) (06) (1181) (138) (131) 32TS-326TS 12(30) 19 1 /2(9) (06) 12(30) 19 1 /2(9) 213T-21T 1 3 (870) 12 3 20 3 3 6 1 /2(1181) 2T (371) 39 3 (00) (32) (2) (27) (76) 1 1 1 3 22 7 (36) (130) (9) (178) 26T 6 (131) 1 /2 BC 286TS (1181) 7 (178) (06) 1 (36) (130) 22 (9) 32TS-326TS 1 3 (131) 36TS-36TS 2 6 1 /2 3 2 1 /2 6 N/A 0TS (6) (122) (19) () (622) (12) 213T-21T 2 1 6 11 / 2 1 6 11 / 2T (73) (170) (73) (170) 1 23 26T 6 1 /2(1181) 1 23 3 (06) (36) (603) E 28T-286T 1 3 / 9 / 7 (06) 1 1 (36) 3 (603) / 9 / 7 1 (1) (11) (18) (131) (1) (11) (18) 32TS-326TS (131) 36TS-36TS 2 6 1 /2 1 / 26 1 6 2 6 1 /2 1 / 26 1 6 0TS (6) (122) (19) (12) (667) (12) (6) (122) (19) (12) (667) (12) 213T-21T 6 1 /2 6 1 /2(1181) GB 2T-26T (1181) 1 3 2 6 8 9 / 1 3 2 6 8 9 / 28T-286T (06) 1 (381) (137) (63) (12) (217) (06) 1 3 3 (381) (137) (63) (12) (217) (131) 32T (131) 182T-18T 1 31(787) 12 3 3 21 1 3 1 3 (879) 12 3 3 21 1 3 213T-21T (371) 3 (870) (32) () (0) (76) (371) 39 3 (00) (32) () (0) (76) A 2T-26T 6 1 /2 13 / 6 1 13 / 6 1 28TS-286TS (1181) 1 6 7 22 1 /2 (18) (19) 1 3 1 6 7 22 1 /2 (18) (19) 32TS-326TS 1 3 (36) (17) (72) (131) (36) (17) (72) 36TS (131) 213T-21T 9 / 6 1 /2(1181) 6 2T /2 (1) 2 6 7 BC /2 6 7 / 2 6 7 1 /2 (06) (1181) (06) 26T 6 (63) (12) (191) 7 / 1 () (63) (12) (191) 1 28T 1 3 (131) () 1 (381) 3 (381) 6 2T-26T 6 1 /2(1181) (131) E 28T-286T 1 3 / 2 1 /2 7 / 7 1 / 7 / 2 1 /2 7 / 7 1 / (113) (68) (138) (202) (113) (68) (138) (202) 32T (131) 2T-26T G 28T-286T 2 6 1 /2 7 / 29 1 /2 6 6 9 2 6 1 /2 7 / 29 1 /2 6 6 9 32T-326T (6) (122) (19) (138) (79) (12) (12) (229) (6) (122) (19) (138) (79) (12) (12) (229) 36T-36T 2T-26T 6 1 /2(1181) 6 BC 1 8 28T-286T 1 3 2 1 /2 7 8 1 1 3 1 8 3 2 1 /2 7 8 1 (06) (381) (213) (68) (178) (2) (06) (131) (381) (213) (68) (178) (2) 32T-326T (131) 2T-26T 6 E 28T-286T 2 6 1 /2 6 27 1 /2 6 6 1 8 1 /2 2 6 1 /2 6 27 1 /2 6 6 1 8 1 /2 32T-326T (6) (122) (19) (12) (699) (12) () (2) (6) (122) (19) (12) (699) (12) () (2) 36T 8 L FRAME TO AND INCLUDING 12 1 /2 IMPELLER 26T 28T-286T 32T-326T 2 6 1 /2 6 1 30 1 /2 6 6 1 /2 9 / 2 6 1 /2 6 1 30 1 /2 6 6 1 /2 9 / (6) (122) (19) (19) (77) (12) () (237) (6) (122) (19) (19) (77) (12) () (237) 6 G * 36T-36T 0TS XL FRAME 12 IMPELLER AND LARGER 36TS 26 9 1 17 6 1 /2 31 6 6 1 /2 9 / 26 9 1 17 6 1 /2 31 6 6 1 /2 9 / 0TS-0TS (660) () (32) () (787) (12) () (237) (660) () (32) () (787) (12) () (237) These dimensions are not to be used for installation purposes unless certified. 20 psi (17 bar) available Maximum Working Pressure 17 psi (12 bar) *13 1 /2 impeller for RPM service with L frame. 8G ONLY STUFFING BOX CONSTRUCTION DIMENSIONS INCHES (MM) PUMP MODEL 1-S PUMP SIZE SUCTION MOTOR FRAME DISCHARGE SIZE SIZE HA HB HD HL HO HP Y 8G 28T-TS 28 70 18 1. 3.7 1 1 3 (203) (2) (711) (1778) (6) (11) (907) (32) (121) Flanges are: 12# ANSI - Standard DISCHARGE HA SUCTION HO HD HL HP Y HB HM 9
THE B&G End Suction Pump System Consists of: B&G Series 1 Pump B&G Triple Duty Valve B&G Suction Diffuser Triple Duty Valve Lowest Pressure Drop ASHRAE 90.1 Energy Efficient Design Three Valves in one! Nonslam drip-tight check valve Positive shutoff valve Calibrated system balance valve EPDM Disc Soft Seat Design Repack Under Pressure Brass Seat & Bronze Disc Stainless Steel Stem Multi-turn Valve (8-9 turns) vs 1 turn range of control Available connections Threaded Flanged Grooved ESP-Plus System Selection Suction Diffuser Full length stainless steel straightening vanes Oversize cylinder assures minimum strainer pressure drop Pressure gauge tap Magnetic drain plug to protect pump seals Adjustable support foot Space saving design reduces the footprint size of the unit Available connections Threaded Flanged Grooved Reducer and elbow provide multiple combinations of inlet and pump suction configurations which eliminate the need for reducer fittings ESP-Plus System Selection
Typical Specification for Series 1 Base Mounted, Flexible Coupled, End-Suction Pumps Furnish and install pumps with performance characteristics as shown on plans. Pumps shall be base mounted, single stage, end suction design with a foot mounted volute to allow removal and service of the entire rotating assembly without disturbing the pump piping, electrical motor connections or pump to motor alignment. A CSA certified condition monitor shall be installed on the pump power end to continuously measure vibration and temperature at the outboard bearing. Vibration modes shall be based on ANSI/HI 9.6.-2009 and ISO 18 recommended levels. Vibration alarms shall be at 0% increase over pump baseline. Minimum vibration of 0.12 inch/sec is required to avoid nuisance tripping. A high vibration alarm shall be at 0.0 inch/ sec. Temperature alarm shall be at 19 F (91 C). The condition monitors electronics shall be potted in epoxy and surrounded by a stainless steel enclosure. Accuracy shall be +/- 1% within an ambient temperature range of -0 F to 212 F (-0 C to 0 C). Pump volute shall be Class 30 cast iron with integrallycast pedestal support feet. The impeller shall be cast bronze enclosed type, balanced to ANSI/HI 9.6.-2009 balance grade G6.3 and keyed to the shaft and secured by a locking capscrew. The liquid cavity shall be sealed off at the pump shaft by an internally-flushed mechanical seal with ceramic seal seat and carbon seal ring, suitable for continuous operation at 22 F (7 C). A replaceable bronze shaft sleeve shall completely cover the wetted area under the seal. Pump shall be rated for minimum of 17 psi (12 bar) working pressure. Volute shall have gauge tappings at the suction and discharge nozzles and vent and drain tappings at the top and bottom. The pump(s) vibration limits shall conform to Hydraulic Institute ANSI/HI 9.6.-2009 for recommend acceptable unfiltered field vibration limits (as measured per ANSI/HI 9.6.-2009 Figure 9.6..2.3.1) for pumps with rolling contact bearings. Baseplate shall be of structural steel or fabricated steel channel with fully enclosed sides and ends, and securely welded cross members. Grouting area shall be fully open. The combined pump and motor baseplate shall be sufficiently stiff as to limit the susceptibility of vibration. The minimum baseplate stiffness shall conform to ANSI/ HI 1.3-2009 for Horizontal Baseplate Design standards. The seismic capability of the pump shall allow it to withstand a horizontal load of 0.g, excluding piping and/or fasteners used to anchor the pump to mounting pads or to the floor, without adversely affecting pump operation. A flexible type, center drop-out design coupler, capable of absorbing torsional vibration, shall be employed between the pump and motor. Pumps for variable speed application shall be provided with a suitable coupler sleeve. The coupling shall be shielded by a dual rated ANSI B1.1 & OSHA 19.219 compliant coupling guard and contain viewing windows for inspection of the coupling. Motor shall meet NEMA and EISA 2007 (where applicable) specifications and shall be of the size, voltage and enclosure called for on the plans. Pump and motor shall be factory aligned, and shall be realigned by the contractor per factory recommendations after installation. The pump(s) selected shall conform to ANSI/HI 9.6.3.1 standards for Preferred Operating Region (POR) unless otherwise approved by the engineer. Each pump shall be factory hydrostatically tested per Hydraulic Institute standards. It shall then be thoroughly cleaned and painted with at least one coat of high grade paint prior to shipment. The pump(s) shall be manufactured, assembled and tested in an ISO 9001 approved facility. Pumps shall be Series 1 as manufactured by Xylem Bell &Gossett or equal. 11
Xylem 1) The tissue in plants that brings water upward from the roots; 2) a leading global water technology company. We re 12,000 people unified in a common purpose: creating innovative solutions to meet our world s water needs. Developing new technologies that will improve the way water is used, conserved, and re-used in the future is central to our work. We move, treat, analyze, and return water to the environment, and we help people use water efficiently, in their homes, buildings, factories and farms. In more than countries, we have strong, long-standing relationships with customers who know us for our powerful combination of leading product brands and applications expertise, backed by a legacy of innovation. For more information on how Xylem can help you, go to www.xyleminc.com Xylem Inc. 8200 N. Austin Avenue Morton Grove, Illinois 6003 Phone: (87) 966-3700 Fax: (87) 96-8379 www.xyleminc.com/brands/bellgossett Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries. 2011 Xylem Inc. B-207H January 2011