Sized for Print B1C29-LEFT SIDE SEAT THORAX SQUIB 1 OPEN. For a complete wiring diagram refer to the Wiring Information See: Diagrams\Electrical.

Similar documents
B1C29 LEFT SIDE SEAT THORAX S... B1C29 LEFT SIDE SEAT THORAX SQUIB 1 OPEN. 6/14/2016 Direct Hit Search

B1C2D RIGHT SIDE SEAT THORAX... B1C2D RIGHT SIDE SEAT THORAX SQUIB 1 OPEN. 6/14/2016 Direct Hit Search

C1219 C1219-STEERING ANGLE SENSOR ERRATIC PERFORMANCE RAM Pickup 6.7L Eng Search. 7/13/2015 Printer Friendly View

P O2 SENSOR 1/1 HEATER CIRCUIT

P2016-INTAKE MANIFOLD RUNNER POSITION SENSOR CIRCUIT LOW

P2017-INTAKE MANIFOLD RUNNER POSITION SENSOR CIRCUIT HIGH

B1EB1-1B-FRONT LEFT SEAT HEATER SENSOR - CIRCUIT RESISTANCE ABOVE THRESHOLD

P0073-AMBIENT AIR TEMPERATURE SENSOR CIRCUIT HIGH

P TURBOCHARGER BOOST CONTROL CIRCUIT/OPEN

B RIGHT SIDE SEAT DEPLOYMENT SQUIB 1 - CIRCUIT OPEN

1 of 8 9/11/2015 3:59 PM

P0406-EGR POSITION SENSOR CIRCUIT HIGH

P0463-FUEL LEVEL SENSOR 1 CIRCUIT HIGH

P0404-EGR Position Sensor Performance

P0113-INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT HIGH

U0171-LOST COMMUNICATION W/UP-FRONT RIGHT SATELLITE ACCELERATION SENSOR

C140C- TRANSFER CASE MOTOR CONTROL CIRCUIT HIGH

P2454-DIESEL PARTICULATE FILTER DIFFERENTIAL PRESSURE SENSOR CIRCUIT LOW

POWERTRAIN CONTROL MODULE (PCM) - NGC

GAS P0344-CAMSHAFT POSITION SENSOR INTERMITTENT

P0401-EGR SYSTEM PERFORMANCE

P3449-MDS SOLENOID 7 CIRCUIT

P013A-O2 SENSOR 1/2 SLOW RESPONSE - RICH TO LEAN

DH - RAM 1500/2500 PICKUP - 6.7L CUMMINS TURBO DIESEL

MK - JEEP COMPASS/PATRIOT - 2.4L 4 CYL DOHC 16V DUAL V.V.T.

C1020-LEFT REAR WHEEL SPEED SENSOR CIRCUIT

P0344-CAMSHAFT POSITION SENSOR INTERMITTENT

Refer to Wiring Diagrams Cell 46, Supplemental Restraint System for schematic and connector information.

P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT - BANK 1 SENSOR 1-5.7L/SRT8

P0123-THROTTLE POSITION SENSOR 1 CIRCUIT HIGH

P0688-AUTO SHUTDOWN SENSE CIRCUIT LOW


P0882-TRANS 12 VOLT SUPPLY RELAY CONTROL CIRCUIT LOW (DIESEL)

JK - JEEP WRANGLER - 3.6L V6 V.V.T.


DTC P0128: THERMOSTAT RATIONALITY

GAS P013C-O2 SENSOR 2/2 SLOW RESPONSE - RICH TO LEAN

P2314-IGNITION COIL 5 SECONDARY CIRCUIT - INSUFFICIENT IONIZATION - 5.7L/SRT8

P0365-CAMSHAFT POSITION SENSOR CIRCUIT-BANK 1 SENSOR 2

B1D7B SEAT HORIZONTAL MOTOR CONTROL CIRCUIT PERFORMANCE

P0222-THROTTLE POSITION SENSOR 2 CIRCUIT LOW

P0365-CAMSHAFT POSITION SENSOR CIRCUIT - BANK 1 SENSOR 2

The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.

DESCRIPTION & OPERATION

P0014-BANK 1 CAMSHAFT 2 POSITION TARGET PERFORMANCE

P2149-BANK 2 (CYLINDERS 4-6) SHORTED HIGH OR LOW

P0018-CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR 1

KA - DODGE NITRO - 4.0L V6 SOHC

P0441-EVAP PURGE SYSTEM PERFO... P0441-EVAP PURGE SYSTEM PERFORMANCE

DTC P Shift Solenoid Circuit Electrical

DTC P Shift Solenoid Circuit Electrical

P0430-CATALYST EFFICIENCY (BANK 2)

Zoom and Print Options

P0456-EVAP PURGE SYSTEM SMALL LEAK

CIRCUIT INSPECTION. DTC B0100/13 Short in D Squib Circuit CIRCUIT DESCRIPTION WIRING DIAGRAM

P0456-EVAP PURGE SYSTEM SMALL LEAK

DTC B0103/12 Short in D and P Squib Circuit (to B+)

TRANSMISSION - NGC. Symptom: P0706-CHECK SHIFTER SIGNAL. When Monitored and Set Condition:

CIRCUIT INSPECTION. DTC B0100/13 Short in D Squib Circuit CIRCUIT DESCRIPTION WIRING DIAGRAM

CIRCUIT INSPECTION. DTC B0100/13 Short in D Squib Circuit CIRCUIT DESCRIPTION WIRING DIAGRAM



DS: Air Conditioning Pressure (ACP) Transducer Sensor

DTC B0015 0D: Driver Pretensioner Deployment Loop Stage 1 Resistance Above Threshold

P245C REQUESTED INFORMATION P245C EGR COOLER BYPASS CONTROL CIRCUIT LOW RAM Pickup 6.7L Eng /12/2014 Printer Friendly View

The A/C heater control must be recalibrated each time an actuator motor is replaced. Refer to

ACCELERATOR CONTROL SYSTEM

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

GROUP 52B CONTENTS. Battery posts, terminals and related accessories contain lead and lead compounds. WASH HANDS AFTER HANDLING.


SUPPLEMENTAL RESTRAINT SYSTEM(SRS)

DRIVEABILITY. Symptom: P0340-NO CAM SIGNAL AT PCM. When Monitored and Set Condition:

RE22 Airbag Systems, Side

Note: Refer to the PCM connector pin numbers in the beginning of this pinpoint test.

TECHNICIAN SAFETY INFORMATION

BASIC DIAGNOSTIC PROCEDURES

P0340-CAMSHAFT POSITION SENSOR CIRCUIT - BANK 1 SENSOR 1

Additions, Revisions, or Updates

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

DTC P0743 sets when the TCM detects an open circuit, a short to power, or a short to ground in the TCC PWM solenoid circuit for 1.5 seconds.

P PRESSURE CONTROL SOLENOID 4 CONTROL CIRCUIT LOW

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

DTC B0133/62 Short in LH and RH P/T Squib Circuits (to B+)

1 of 14 9/4/2016 4:05 PM

DTC B0132/61 Short in LH and RH P/T Squib Circuit (to Ground)

DTC P0502 Vehicle Speed Sensor (VSS) Circuit Low Input (3.1L VIN M)

Fuel Injector Control Module (FICM ) Low Voltage

Revised : September 2015 September 2015 Dealer Service Instructions for: Safety Recall R36 Steering Wheel Wiring

DA: Intake Air Temperature (IAT) Sensor

2003 Ford Explorer - Diagnostics > Diagnostic Routines > Powertrain > On Board Diagnostics > P... Page 1 of 18

SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

P144F REQUESTED INFORMATION P144F EGR COOLER BYPASS STATUS LINE CIRCUIT HIGH RAM Pickup 6.7L Eng /12/2014 Printer Friendly View

2004 Toyota RAV ACCESSORIES/SAFETY EQUIPMENT Toyota - Air Bag Restraint Systems

SELF-DIAGNOSTIC TESTS

8N - 18 POWER WINDOWS

2007 Dodge Nitro R/T ENGINE Starting - Service Information - Nitro. Starting - Service Information - Nitro

SUPPLEMENTAL RESTRAINTS SYSTEM

Scan Tool Does Not Communicate with Class 2 Device (W/O Immobilizer)

ME: Fuel Pump Control - High Pressure Fuel Injection Pump

DR: Camshaft Position (CMP) Sensor

Transcription:

B1C29-LEFT SIDE SEAT THORAX SQUIB 1 OPEN For a complete wiring diagram refer to the Wiring Information See: Diagrams\Electrical. When Monitored: With the ignition on. http://alldatapro.com/alldata/pro~v372401349~c46382~r0~od~n/0/138181779/139756261/139756334/139756336/34853741/96340231/96340248/176614761/1 1/8

Set Condition: The Occupant Restraint Controller (ORC) monitors the resistance of the Left Seat Airbag circuits. If an open or high resistance condition is detected on the Left Seat Airbag circuits the ORC will set this DTC. 1. DETERMINE ACTIVE OR STORED DTC Ensure that the battery is fully charged. The scan tool, SRS Airbag Load Tool MRL 8443, and DVOM are required to perform the following test. 1. Turn the ignition on. Select ACTIVE or STORED DTC: ACTIVE DTC Go To 2 STORED DTC Go To 6 2. CHECK FOR OPEN LEFT SEAT AIRBAG SQUIB http://alldatapro.com/alldata/pro~v372401349~c46382~r0~od~n/0/138181779/139756261/139756334/139756336/34853741/96340231/96340248/176614761/1 2/8

Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to 1. Disconnect the Left Seat Airbag connector. Do not place an intact undeployed Seat Squib Airbag face down on a hard surface, the airbag will propel into the air if accidentally deployed. Failure to follow these instructions may result in possible serious or fatal injury. Check connectors - Clean and repair as necessary. 2. Connect the 8443 Load Tool and 8443-1 Jumper to the Left Seat Airbag connector. Turn the ignition on, then reconnect the 12-volt battery. Wait two minutes before proceeding. Failure to http://alldatapro.com/alldata/pro~v372401349~c46382~r0~od~n/0/138181779/139756261/139756334/139756336/34853741/96340231/96340248/176614761/1 3/8

3. With the scan tool, read the active ORC DTCs. Does the scan tool display: B1C29-LEFT SIDE SEAT THORAX SQUIB 1 OPEN? Go To 3 Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to Replace the Left Seat Airbag. 3. CHECK FOR OPEN LEFT SEAT AIRBAG SQUIB CIRCUIT IN THE SEAT BACK http://alldatapro.com/alldata/pro~v372401349~c46382~r0~od~n/0/138181779/139756261/139756334/139756336/34853741/96340231/96340248/176614761/1 4/8

Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to 1. Disconnect the Left Seat Airbag C353 in-line connector (under Left Seat). Check connectors - Clean and repair as necessary. 2. Connect the 8443 Load Tool and 8443-20 Jumper to the Left Seat Airbag C353 in-line connector (Body Side). Turn the ignition on, then reconnect the 12-volt battery. Wait two minutes before proceeding. Failure to 3. With the scan tool, read the active ORC DTCs. Does the scan tool display: B1C29-LEFT SIDE SEAT THORAX SQUIB 1 OPEN? Go To 4 Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to Repair or replace the Left Seat Airbag wiring harness (Side Airbag Jumper). Open Left Seat Airbag circuits between the C353 in-line connector and the Left Seat Airbag connector. 4. CHECK FOR OPEN (R5) LEFT SEAT SQUIB 1 LINE 2 CIRCUIT IN THE BODY HARNESS TO THE SEAT http://alldatapro.com/alldata/pro~v372401349~c46382~r0~od~n/0/138181779/139756261/139756334/139756336/34853741/96340231/96340248/176614761/1 5/8

Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to 1. Disconnect the 8443 Load Tool and Jumper from the C353 in-line connector (body side). 2. Disconnect the ORC connectors. Check connectors - Clean and repair as necessary. 3. Connect the Load Tool ORC 8443-25 Adaptor to the ORC connectors. 4. Measure the resistance of the (R5) Left Seat Squib 1 Line 2 circuit between the ORC 8443-25 Adaptor cavity C2-16 and the C353 in-line connector (body side) cavity 1. Is the resistance below 1.0 ohm? Go To 5 Repair or Replace the (R5) Left Seat Squib 1 Line 2 circuit for an open or high resistance. 5. CHECK FOR AN OPEN (R7) LEFT SEAT SQUIB 1 LINE 1 CIRCUIT IN THE BODY HARNESS http://alldatapro.com/alldata/pro~v372401349~c46382~r0~od~n/0/138181779/139756261/139756334/139756336/34853741/96340231/96340248/176614761/1 6/8

1. Measure the resistance of the (R7) Left Seat Squib 1 Line 1 circuit between the ORC 8443-25 Adaptor cavity C2-15 and the C353 in-line connector (body side) cavity 2. Is the resistance below 1.0 ohm? If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to follow these instructions may result in possible serious or fatal injury. Replace the ORC. Repair or Replace the (R7) Left Seat Squib 1 Line 1 circuit for an open or high resistance. 6. CHECKING STORED OR INTERMITTENT CODES Diagnose and repair all active codes before diagnosing stored codes. 1. With the scan tool, record and erase all Airbag System Module DTCs. Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to http://alldatapro.com/alldata/pro~v372401349~c46382~r0~od~n/0/138181779/139756261/139756334/139756336/34853741/96340231/96340248/176614761/1 7/8

2. Using the wiring diagram/schematic as a guide, inspect the related wiring and connectors for chafed, pierced, pinched, and partially broken wires, and for broken, bent, pushed out, corroded, and contaminated terminals. Repair as necessary. 3. Reconnect all disconnected components and harness connectors. Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to 4. With the scan tool, monitor for active codes while performing the following: Wiggle the wiring harness and connectors of the related airbag circuit. Continue the test until either a code becomes active or the problem area is isolated. 5. In the previous steps you have attempted to recreate the conditions responsible for setting the DTC in question/causing the intermittent condition. Are any ACTIVE DTCs present? Perform the appropriate DTC. See: Testing and Inspection. problem found at this time. Erase all codes before returning the vehicle to the customer. http://alldatapro.com/alldata/pro~v372401349~c46382~r0~od~n/0/138181779/139756261/139756334/139756336/34853741/96340231/96340248/176614761/1 8/8