TM SPECIFICATIONS F180 F180@36 F220 HOISTLIFTRUCK
Lift Truck Specifications GE NE RA L DI- ME NSI ON S PE RF OR MA NC E WT. CH AS SIS 1 Manufacturer Hoist Liftruck Mfg., Inc. 1 2 Model F180 2 3 Capacity, Rated lb. (kg) 18,000 (8180) 3 4 Load Center in. (mm) 24 (610) 4 5 Power Type GAS/LP/Diesel 5 6 Operator Type SIT 6 7 Tire Type, front/rear Solid/Solid 7 8 Wheels, front/rear (X=driven) 2x/2 8 10 2-stg. Limited free-lift(lfl), (TOF) in. (mm) 93 (2362) 10 11 Limit free tilt (TOF) in. (mm) 0 (0) 11 12 Opt. 3-stg.full free-lift(ffl), (TOF) with/ w/o LBR in. (mm) 130.5 (3315) 12 13 Forks, width/thickness in. (mm) 6.0 (152.4) / 2.75 (69.8) 13 14 Tilt angle, forward/backward Degree 6 / 8 14 15 Length to face of forks in. (mm) 133.88 (3400) 15 16 Overall width, standard tires in. (mm) 56.7 (1440) 16 17 Height, std. mast lowered in. (mm) 85.25 (2165) 17 18 Height, std. Mast ext.-w/o LBE in. (mm) 139 (3530) 18 19 Turning radius, minimum outside in. (mm) 115 (2921) 19 20 Center of drive wheel to face of forks in. (mm) 25.88 (657) 20 22 Aisle width (Add Id. Lgth for 90 deg. Stacking aisle) in. (mm) 118 (2997) 22 23 Stability (Comply with ANSI, CE)* Yes, Yes 23 24 Travel Speed, pwrshft Loaded/unloaded mph (km/h) 14 (22.5) 24 25 Lift Speed, std. mast empty/loaded ft/min (m/s) 78 (.40) / 72 (.36) 25 Opt. 3-stg full free-lift (FFL) empty / loaded ft/min (m/s) 75 (.38) / 68 (.345) 26 Lowering, std. mast, NL/RL ft/min (m/s) 65 (.33) / 98 (.498) 26 Opt. 3-stg full free-lift (FFL) empty / loaded ft/min (m/s) 65 (.33) / 115 (.584) 27 Drawbar pull, Powershift, Max 1 mph lb. (kn) 8006 (36kN) 27 28 Gradeability@.9 coef. Empty / Loaded 36% / 20% 28 30 Total approximate weight, standard truck lb. (kg) 24700 (11203) 30 31 Axle loading, static, front loaded / empty lb. (kg) 38600 (17545) / 8230 (3733) 31 Axle loading, static, rear loaded / empty lb. (kg) 4520 (2050) / 16480 (7475) 32 Number tires front/rear 2.0 / 2.0 32 33 Size of tires, front 28X12X22 33 34 Size of tires, Rear 22X8X16 34 35 Wheel Base in. (mm) 80 (2032) 35 36 Tread width, center of steer tires, single in. (mm) 48.0 (1219) 36 Tread width, center of drive tires, single in. (mm) 44.0 (1118) 37 Ground clearance, no load lowest pt. in. (mm) 4.0 (101.6) 37 38 Ground clearance, no load ctr. Whlbs in. (mm) 4.5 (114.3) 38 39 Brakes, method of control, service / parking hydraulic/mechanical 39 40 Brakes, method of operation, service / parking foot/hand 40 42 Battery, volts/ Cold cranking ampres 12/355 42 46 Engine, make & model GM V6-4.3L / Perkins 1004-4 46 DRI 47 Output per SAE standards, Gas / LP~~Diesel hp (kw) LP / 90 (67) / Diesel 86 (64) 47 VE TR 48 Governed speed, NL RPM 2400 48 AIN 49 Cycle / no. of cylinders / displacement cu.in. (cm3) 6/4.3L ~~ 4/4.23L 49 51 clutch type, powershift torque convertor 51 52 Gear changetype, powershift hand 52 53 No. speeds fwd. / reverse 3 53 54 Transmission type Powershift (Autoshift) 54 55 Relief pressure for attachments psi (kpa) 2,250 (15,500) 55 Note: The specifications for the Liftruck in this sheet is when equipped with standard equipment. Actual specifications and performance may vary depending on how equipped, operating conditions, and condition of forklift. If specifications are critical, the specific application should be reviewed with your dealer.
Lift Truck Specifications GE NE RA L DI- ME NSI ON S PE RF OR MA NC E WT. CH AS SIS DRI VE TR AIN 1 Manufacturer Hoist Liftruck Mfg., Inc. Hoist Liftruck Mfg., Inc. 1 2 Model F180@36 F220 2 3 Capacity, Rated lb. (kg) 18,000 (8165) 22,000 (9979) 3 4 Load Center in. (mm) 36 (1000) 24 (610) 4 5 Power Type GAS/LP/Diesel GAS/LP/Diesel 5 6 Operator Type SIT SIT 6 7 Tire Type, front/rear Solid/Solid Solid/Solid 7 8 Wheels, front/rear (X=driven) 2x/2 2x/2 8 10 2-stg. Limited free-lift(lfl), (TOF) in. (mm) 73.5 (1866) 73.5 (1866) 10 11 Limit free tilt (TOF) in. (mm) 0 (0) 0 (0) 11 12 Opt. 3-stg.full free-lift(ffl), (TOF) with/ w/o LBR in. (mm) options options 12 13 Forks, width/thickness in. (mm) 7.0 (152.4) / 3.0(76) 7.0 (152.4) / 3.0(76) 13 14 Tilt angle, forward/backward Degree 6 / 8 6 / 8 14 15 Length to face of forks in. (mm) 133.88 (3400) 133.88 (3400) 15 16 Overall width, standard tires in. (mm) 60.7 (1542) 60.7 (1542) 16 17 Height, std. mast lowered in. (mm) 85.25 (2165) 85.25 (2165) 17 18 Height, std. Mast ext.-w/o LBE in. (mm) 128.75 (3270) 128.75 (3270) 18 19 Turning radius, minimum outside in. (mm) 115 (2921) 115 (2921) 19 20 Center of drive wheel to face of forks in. (mm) 25.88 (657) 25.88 (657) 20 22 Aisle width (Add Id. Lgth for 90 deg. Stacking aisle) in. (mm) 124 (3149) 124 (3149) 22 23 Stability (Comply with ANSI, CE)* Yes, Yes Yes, Yes 23 24 Travel Speed, pwrshft Loaded/unloaded mph (km/h) 14 (22.5) 14 (22.5) 24 25 Lift Speed, std. mast empty/loaded ft/min (m/s) 73 (.37) / 50 (.254) 73 (.37) / 50 (.254) 25 Opt. 3-stg full free-lift(ffl) empty / loaded ft/min (m/s) options options 26 Lowering, std. mast, NL/RL ft/min (m/s) 60 (.305) / 92 (.467) 60 (.305) / 92 (.467) 26 Opt. 3-stg full free-lift(ffl) empty / loaded ft/min (m/s) options options 27 Drawbar pull, Powershift, Max 1 mph lb. (kn) 8316 (37kN) 8316 (37kN) 27 28 Gradeability@.9 coef. Empty / Loaded 26% / 15% 26% / 15% 28 30 Total approximate weight, standard truck lb. (kg) 24550 (11135) 25050 (11222) 30 31 Axle loading, static, front loaded / empty lb. (kg) 38350 (17395) / 7730(3506) 41867 (18990) / 7730 (3506) 31 Axle loading, static, rear loaded / empty lb. (kg) 4200 (1905) / 16820 (7630) 4683 (2124 / 16820 (7630) 32 Number tires front/rear 2.0 / 2.0 2.0 / 2.0 32 33 Size of tires, front 28X14X22 28X14X22 33 34 Size of tires, Rear 22X8X16 22X8X16 34 35 Wheel Base in. (mm) 80 (2032) 80 (2032) 35 36 Tread width, center of steer tires, single in. (mm) 48.0 (1219) 48.0 (1219) 36 Tread width, center of drive tires, single in. (mm) 46.0 (1168) 46.0 (1168) 37 Ground clearance, no load lowest pt. in. (mm) 4.0 (101.6) 4.0 (101.6) 37 38 Ground clearance, no load ctr. Whlbs in. (mm) 4.5 (114.3) 4.5 (114.3) 38 39 Brakes, method of control, service / parking hydraulic/mechanical hydraulic/mechanical 39 40 Brakes, method of operation, service / parking foot/hand foot/hand 40 42 Battery, volts/ Cold cranking ampres 12/355 12/355 42 46 Engine, make & model GM V6-4.3L / Perkins 1004-4 GM V6-4.3L / Perkins 1004-4 46 47 Output per SAE standards, Gas / LP~~Diesel hp (kw) LP / 90 (67) / Diesel 86 (64) LP / 90 (67) / Diesel 86 (64) 47 48 Governed speed, NL RPM 2400 2400 48 49 Cycle / no. of cylinders / displacement cu.in. (cm3) 6/4.3L ~~ 4/4.23L 6/4.3L ~~ 4/4.23L 49 51 clutch type, powershift torque convertor torque convertor 51 52 Gear changetype, powershift hand hand 52 53 No. speeds fwd. / reverse 3 3 53 54 Transmission type Powershift (Autoshift) Powershift (Autoshift) 54 55 Relief pressure for attachments psi (kpa) 2,250 (15,500) 2,250 (15,500) 55 58 Sound level avg. at operators ear per ANSI B56.11.5 dba 77 77 58 Note: The specifications for the Liftruck in this sheet is when equipped with standard equipment. Actual specifications and performance may vary depending on how equipped, operating conditions, and condition of forklift. If specifications are critical, the specific application should be reviewed with your dealer.
CAPACITY F180 F180@36 F220 18,000# @24 LOAD CENTER 18,000# @36 LOAD CENTER 22,000# @24 LOAD CENTER *************************************************** Capacity and / or tilt may be restricted or derated for 3-stage masts or lift heights above 170. Please check with your Hoist dealer or call Hoist Liftruck for your specific needs. ************************************************ HI-VIS Mast, ITA carriage, and 48 forks are included in the price of the truck. All trucks have two forward lights, two back-up lights, brake lights, backup alarm, and yellow flashing beacon. POWER PLANT -The standard engine for the titan is the GM 90 degree, 4.3 Liter, V-6. It delivers 90 horsepower and 195 ft-lbs of torque at 2400 RPM. It provides power to propel the truck and with a full load to 14 M.P.H. quickly. LP gas is standard (tanks not included). Optional gas or dual fuel systems are available. THE ENGINE MANAGEMENT SYSTEM -Utilizes a control module that regulates fuel delivery, governs speed, controls the ignition, has built-in overheating protection, and maintains the RPM during hydraulic functions. OPTIONAL DIESEL -Perkins 1004, 4.23 L is available with 86 horsepower and 221 ft -lbs of torque at 2400 RPM. Designed to give at least 12,000 hours of productive service before needing a basic overhaul and meets stringent emission legislation functions. TRANSMISSION -The Hoist 3-speed powershift (optional autoshift) transmission was designed for the power and performance requirements of heavy industry. The modular electronic controls allow closer gear ratios that provide smoother shifting between gears. This greatly improves vehicle and operator performance by shifting the transmission automatically at predetermined speeds and load points. The autoshift transmission frees the operator of the mechanical function of shifting, so he can concentrate on the machine tasks. It has an externally mounted pump and integral filter. Inching controls provide smooth operations in or out of loads. TRACTION LOAD AXLE -Hoist utilizes a planetary drive axle. Designed for high load capacities, extended service life, and reduced maintenance. All gears are heat treated and precision ground to deliver the reliability expected by our customers. BRAKES -Drum-type brakes provide solid reliability and ease of service. Large braking surfaces give ample capacity in high usage applications without overheating or glazing. Disc-type parking brake is hand actuated to be set safely when the operator exits the truck. A warning light is on the instrument panel alerts driver when parking brake is engaged. STEERING SYSTEM -Hoist designed the steer axle requires only 2 3/4 turns of the wheel to provide lock-to-lock turning of the steer wheels. The heavy-duty steer axle features heavy alloy steel plate sections around a single, double-acting cylinder. A full turn of the wheels provides maneuverability in tight areas while maintaining directional tracking of the tire, with no skidding or premature tire wear. TITAN MAST DESIGN -Heavy-duty extruded and rolled mast rails provide unsurpassed visibility on our standard HI-VIS mast. This mast provides full capacity at maximum lift heights. Lift heights are available to 170. The mast and apron rollers integrate a side thrust roller to support uneven load distribution on the forks. For the full freelift or extended lift height requirements, we offer an optional 3-stage full freelift mast. Shielded hose reeving is included for auxiliary hosing. Talk to your local dealer for restrictions and special requirements. CARRIAGES -ITA CLASSIV OR CLASS V carriages with six roller support and integral side thrust rollers provide reliable support and load distribution. This provides for routine installation of any standard attachment. FORKS -48 ITA mount pallet forks are included. Additional sizes, as well as coil contour forks are available options. HYDRAULIC SYSTEM -Ergonomic soft touch control levers provide smooth, comfortable, controlled operation of the hydraulic functions. The load-sensing on-demand hydraulic system provides smooth, reliable control and limits demands on the powerplant. The piston pump provides support control and quiet operation. A fuse in the lift cylinder provides protection from sudden loss of pressure. In the event of broken lift hose, the lift cylinder locks in position to provide safety for the operator, load and people or product near by. OPERATORS COMPARTMENT -Semi-suspension adjustable seat, retractable seat belts, and hip restraints provide safe and comfortable operation of the Titan Series Liftrucks. A built-in cup holder, cushioned floor cover and clip board in the cabin assist in operator function and comfort. The easy entry/exit design, non-skid steps, tilt steering, illuminated digital instrumentation, column mount directional shifter, horn button and steering knob on steering wheel, complete the usability package. SOUND LEVELS -Operator s cab, heater, wiper, and defrosters, air conditioning, fire safe fluids, special attachments and tools are only a few options available. Contact your dealer with your special requirements for more information on how to solve your special problems. SOUND LEVELS -Acceptable standards are reached via drive train design and insulation of the operator s compartment.
Meeting the Needs of Heavy Industry OPTIONAL BOX STYLE. SHORTENS BY 10 INCHES.
TM Contact your local Hoist Liftruck dealer for more information. Hoist Liftruck Mfg., Inc. 6499 W. 65th Street Bedford Park, IL 60638 800.367.5600 fax 800.367.5605 708.458.2200 fax 708458.1176 Www.hoistlift.com Made in the U.S.A. Hoist Liftruck continually improves it s products. Specefications are subject to change without notice.