JTC-1147 6" CHAIN WRENCH Used for installation and dismantling designs such as pipes of almost any diameter. Handle: 6" Chain: 18" (400mm) JTC-1149 20" CHAIN WRENCH Used for installation and dismantling designs such as pipes of almost any diameter. Handle: 20" Chain: 25" JTC-1150 12" STRAP WRENCH Designed for removing oil filters. Handle: 12" Strap length: 36"
JTC-1355 EUROPEAN DOOR HINGE / HANDLE KIT For removing rear door hinge and handle T30 x 250mmL BENZ 220C and NEW S. T20 x 210mmL VW and BENZ Bits M4, M8, M10, T40, T45 x 25mm 1998 and newer VW golf, Jetta, Passat & new Bettle. Ratchet Handle x 240mm JTC-1728 ANGLE TIP LOCK RING PLIERS Spread snap lock rings on brakes, transmissions, pedal shafts, clutch shafts & machine tools. Jaws have deep serrations on the outside of tip to help lock rings securely. Spreading: 3.5 ~ 28mm. Total length: 225mm JTC-3002 36" JUMBO PRY BAR Chrome-molybdenum steel. Go-through alloy steel square Rugged firm grip designed plastic handle. Excellent for prying engine, cylinder head, transmission cases, manifold and drive line components. Flat tip.
JTC-3003 36" JUMBO PRY BAR (BEND) Chrome-molybdenum steel. Go-through alloy steel square. Rugged firm grip designed plastic handle. Excellent for prying engine, cylinder head, transmission cases, manifold and drive line components. Curve tip. Size: #3 x 8m/m Full length: 250mm JTC-3024 T TYPE SCREWDRIVER JTC-3117 4 PCS PRY BAR SET Spec.: 7/16" x 24"L, 7/16" x 18"L. 3/8" x 12"L, 1/4" x 8"L.
JTC-3207 IMPACT DRIVER SET Bits. Material: S2. 4 Bits x 36mml: PHILLIPS NO.2, NO.3 SLOTTED θ8m, 10mm. 28 Bits x 80mml: PHILLIPS NO.2, NO.3 JTC-3311 EXTRA LONG NEEDLE NOSE PLIERS Made from CR-MO material to provide a high strength level and uniform hardness. The design of pliers means reach and application advantage at every turn. Long, slim jaws and flash-riveted joints enable pliers to reach into recessed areas. Spec: 90 BEND Length: 11" JTC-3312 EXTRA LONG ROUND JAWS PLIER Made from CR-MO material. Suitable for using on hoses, spark plug wires, etc. Ø: 8mm (5/16") Length: 11"
JTC-3313 EXTRA LONG ROUND JAWS PLIERS Made from CR-MO material. Suitable for using on hoses, spark plug wires, etc. Ø: 13mm (1/2") Length: 11" JTC-3314 EXTRA LONG ROUND JAWS PLIERS Made from CR-MO material. Suitable for using on hoses, spark plug wires, etc. Ø: 19mm (3/4") Length: 11" JTC-3471 10 1/2" SNAP RING PLIERS SET Feature replaceable tips and have a spring ratchet locking mechanism to hold circlip securely against tension. Offset tips make it easier to facilitate circlip. 2 of each 2.75mm tips in o,15,45,90 2 of each 3.0mm tips in o, 15, 45, 90 Length: 10-1/2" (265mm) Spread: Internal - 60mm ~ 100mm External - 38mm ~ 85mm
JTC-3501 8 PCS FOLDING HEX SET Convenient folding type for easy & high torque application. Made from chrome vanadium steel & heat treated. 2.5, 3, 4, 5, 6, 7, 8, and 10mm. JTC-3502 8 PCS FOLDING STAR SET Convenient folding type for easy and torque application. Made from chrome vanadium steel and heat treated. T9, 10, 15, 20, 25, 27, 30 and 40. JTC-3503 8 PCS FOLDING STAR SET (TAMPER PROOF) Convenient folding type for easy and high torque application. Special design with hole in the head to fit the special screws. Made form chrome vanadium steel and heat treated. T9H, 10H, 15H, 20H, 25H, 27H, 30H and T40H.
JTC-3504 9 PCS LONG HEX SET Plastic holder professionally designed for nice installation and convenience usage. Extra-long arm series can save strength and time for enable pleasant operation. Material: S2. 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10mm. JTC-3505 9 PCS LONG BALL POINT HEX SET Work in hard to reach areas. Faster inserting and removing. Full depth engagement. Material: S2 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10mm. Special offer for CR-V material JTC-3508A JTC-3506 9 PCS LONG BALL POINT HEX SET Work in hard to reach areas. Faster inserting and removing. Full depth engagement. Material: S2 1/16" 5/64", 3/32", 1/8", 5/32", 3/16", 1/4", 5/16", 3/8"
JTC-3509 58 PCS POWER BIT SET Material: S2 9 pcs 30mmL star power bit: T20, T25, T27, T30, T40, T45, T50, T55, T60. 9 pcs 75mmL star power bit: T20, T25, T27, T30, T40, T45, T50, T55, and T60. 9 pcs 30mmL hex power bit: 4,5,6,7,8,10,12,14,17. 9 pcs 75mmL hex power bit: 4, 5, 6, 7, 8, 9, 10, 12, 3/8". 5 pcs 30mmL spline power bit: M5, M6, M8, M10, M12. 8 pcs 75mmL spline power bit: M5, M6, M8, M9, M10, M12, M14, M16H. 5 pcs 75mmL ribe power bit: RM6, RM7, RM8, RM10, RM12. 2 pcs 75mmL square power bit: 8, 10. 1 pc 10mm(hex) x 3/8" Dr. Adapter. 1 pc 10mm(hex) x 1/2" Dr. Adapter. JTC-3629 29" JUMBO PRY BAR Go-through alloy steel square. Rugged firm grip designed plastic handle. Excellent for prying engine, cylinder head, transmission cases, manifold and drive line components. JTC-3701 90 ANGLE SCREWDRIVER SET Perfect for fastening jobs in confined areas. Features a quick-set handle holding in all angle for efficient performance and 1/4" hex shank can be used with power driver or by included hand driver. #1 and #2-25m/m bit included.
JTC-3704 SELF ADJUSTED PLIERS The gripping span remains substantially constant for any size workpiece. Jaws always grip in parallel position up to 1-3/8" (35mm). Uniform, powerful grip. Self-adjusts to workpiece size. Super strong, laminated heat-treated steel construction. JTC-3705 SELF ADJUSTED PLIERS The gripping span remains substantially constant for any size workpiece. Jaws always grip in parallel position up to 2" (50mm). Uniform, powerful grip. Self-adjusts to workpiece size. Super strong, laminated heat-treated steel construction. JTC-3819 EXTRA LONG NEEDLE NOSE PLIERS Made from CR-MO material to provide a high strength level and uniform hardness. The design of pliers means reach and application advantage at every turn. Long, slim jaws and flash-riveted joints enable pliers to reach into recessed areas. Spec: 0 STRAIGHT Length: 11"
JTC-3820 45 EXTRA LONG NEEDLE NOSE PLIERS Made from CR-MO material to provide a high strength level and uniform hardness. The design of pliers means reach and application advantage at every turn. Long, slim jaws and flash-riveted joints enable pliers to reach into recessed areas. Spec: 45 BEND Length: 11" JTC-3924 9 IN 1 STAR KEY SET (TAMPER PROOF) Made from SNCM8660 material. Long shank to reach confined areas or increase torque. With double end tamper resist T10H, 15H, 20H, 25H, 27H, 30H, 40H, 45H, 50H. JTC-3925 9 PC STAR SCREWDRIVER SET (TAMPER PROOF) Chrome molybdenum steel with heat treated blade & magnetic tip Distinctive design with hole in the head to fit the special screws T8H x 100mm, T9H x 100mm, T10H x 100mm, T15H x 125mm, T20H x 125mm, T25H x 125mm, T27H x 150mm, T30H x 150mm, T40H x 150mm.
JTC-3933 42 PCS POWER BIT SET Material: S2 8 pcs 30mm star power bit: T20, T25, T27, T30, T40, T45, T50, T55. 8 pcs 75mm star power bit: T20, T25, T27, T30, T40, T45, T50, T55. 7 pcs 30mm hex power bit: 4, 5, 6, 7, 8, 10, 12mm. 7 pcs 75mm hex power bit: 4, 5, 6, 7, 8, 10, 12mm. 5 pcs 30mm spline power bit: M5, M6, M8, M10, M12. 5 pcs 75mm spline power bit: M5, M6, M8, M10, M12. 1 pc 10mm (hex) x 3/8" Dr. Adapter 1 pc 10mm (hex) x 1/2" Dr. Adapter JTC-4066 LARGE LOCKING RING PLIERS Applicable:Large rings on drive shafts in earthmovers and construction vehicles. Tip form: Interchange, wide, milled Tip size (mm):3.5 x 8mm; spreading 8-75mm Total length: 330mm JTC-4093 S TYPE WRENCH 12mm Special S angle designed for better operation. Use for installing and removing the door hinge screws. SIZE: 12mm; 12PT Applicable: TOYOTA, NISSAN, HONDA, MITSUBISH, SUZUKI, etc.
JTC-4754 DOOR HINGE BOLTS REMOVER KIT Special angle wrench design to quickly and easily loosen and tighten the bolts in door hinges. Also for adjusting the Toe on the rear axle. 7 pcs bits: M8, M10, M12, T30, T40, T45, T50. 1 pc special angle 3/8" DR. wrench. 1 pc 45 8mm gear wrench. Applicable: VW, AUDI, BENZ, etc. JTC-5056 PARROT TYPE LOCKING PLIERS The jaws made of CR-MO, and bodily heattreated. Total length: 215mm. Capacity: φ5 ~ φ40mm. JTC-5057 ADJUSTABLE HOSE PINCH OFF LOCKING PLIERS The jaws made of CR-MO, and bodily heat-treated. Total length: 280mm. Nose length: 120mm.
JTC-5350 11 PCS SHORT HEX KEY SET Size: 1.5, 2, 2.5, 3, 4, 5, 6, 7, 8, 10, 12mm. Material: S2, sanding chrome finished surface. Length: short type. JTC-5351 7 PCS LONG HEX KEY SET Size: 2.5, 3, 4, 5, 6, 8, 10mm. Material: S2 sanding chrome finished surface. Length: extra-long type. JTC-5357 8 PCS L HOLDER STAR BIT SET 7 pcs bits: T10, T15, T20, T25, T27, T30, T40. 1 pc 2-way L type bit holder wrench. Bit material: S2, silver-plated Size: 1/4" x 30mmL
JTC-5358 8 PCS S L HOLDER STAR BIT SET (TAMPERPROOF) 7 pcs bits: T10H, T15H, T20H, T25H, T27H, T30H, T40H. 1 pc 2-way L type bit holder wrench. Bit material: S2, silver-plated. Size: 1/4" x 30mmL JTC-5359 8 PCS L HOLDER HEX BIT SET 7 pcs bits: H2, H3, H4, H5, H6, H7, H8. 1 pc 2-way L type bit holder wrench. Bit material: S2, silver-plated. Size: 1/4" x 30mmL JTC-5360 8 PCS L HOLDER BIT SET 7 pcs bits: PH1, PH2, PH3, PZ1, PZ2, SL4, SL7. 1 pc 2-way L type bit holder wrench. Bit material: S2, silver-plated. Size: 1/4" x 30mmL
JTC-5361 10 PCS STAR BIT SET 10 pcs bits: T7, T8, T9, T10, T15, T20, T25, T27, T30, T40. Material: S2 Size: 1/4" x 25mmL JTC-5362 10 PCS 5 PT STAR BIT SET (TAMPERPROOF) 10 pcs bits: TS08, TS10, TS15, TS20, TS25, TS27, TS30, TS40, TS45, TS50. Material: S2 Size: 1/4" x 25mmL JTC-5363 10 PCS STAR BIT SET (TAMPERPROOF) 10 pcs bits: T7H, T8H, T9H, T10H, T15H, T20H, T25H, T27H, T30H, T40H. Material: S2 Size: 1/4" x 25mmL
JTC-5364 33 PCS COMPREHENSIVE BIT SET (TAMPERPROOF) 9 pcs star bits (tamperproof): T8H, T10H, T15H, T20H, T25H, T27H, T30H, T35H, T40H. 12 pcs hex bits (tamperproof): 2, 2.5, 3, 4, 5, 6mm; 5/64", 3/32", 7/64", 1/8", 9/64", 5/32" SEA. 3 pcs torque set bits: 6, 8, 10. 4 pcs tri-wing bits: 1, 2, 3, 4. 4 pcs spanner bits: 4, 6, 8, 10. 1 pc magnetic bit holder (60mmL). Bit size: 1/4" x 25mmL JTC-5365 6 PCS SPLINE BIT SET (30L) 5 pcs 10mm spline bits x 30L: M5, M6, M8, M10, M12. 1 pc 1/2" DR. x 10mm bit holder. Bit material: S2. JTC-5366 7 PCS STAR BIT SET (30L) 6 pcs 10mm star bits x 30L: T25, T30, T40, T45, T50, T55. 1 pc 1/2" DR. x 10mm bit holder. Bit material: S2.
JTC-5405 COMFORT GRIP LOCKING PLIERS Made from CR-MO Length: 250mm; setting switch covered with TPR material. Designed for easy holding and releasing, saves more time and energy. JTC-5610 55 PCS MINI RATCHET BITS SET Bit material: S2, length: 20mm, with ratchet length: 20mm 1 pc super mini ratchet. 1 pc ratchet screwdriver. 1 pc magnet extension bar. 11 pcs STAR T6, T7, T8, T9, T10, T15, T20, T25, T27, T30, T40. 11 pcs STAR (tamperproof) T6H, T7H, T8H, T9H, T10H, T15H, T20H, T25H, T27H, T30H, T40H. 6 pcs HEX H2, H2.5, H3, H4, H5, H6. 8 pcs 5 PT. STAR (tamperproof) TS8H, TS10H, TS15H, TS20H, TS25H, TS27H, TS30H, TS40H. 4 pcs Philips PH0, PH1, PH2, PH3. 4 pcs Slotted FD3, FD4, FD5, FD6, FD7. 4 pcs Y-type 1-2-3-4. 3 pcs X-type 6-8-10. JTC-5623 16" SNAP RING PLIERS SET Replaceable tips and spring ratchet locking mechanism to hold against snap ring tension. one internal snap ring plier and one external snap ring plier. 3mm tips: straight, 45 and 90. Capacity: 85 ~ 170mm
JTC-5624 20" SNAP RING PLIERS SET Replaceable tips and spring ratchet locking mechanism to hold against snap ring tension. one internal snap ring plier and one external snap ring plier. 3.5mm tips: 2 sets 90. Bolt, nut and washers: 4 sets. Capacity: 165 ~ 300mm JTC-5709 EXTRA LONG RETAINING RING PLIER (INTERNAL STRAIGHT) Length: 225mm Tip length: 75mm Tip diameter: Ø1.2mm JTC-5710 EXTRA LONG RETAINING RING PLIER (INTERNAL BENT) Length: 225mm Bent Tip length: 65mm Tip diameter: Ø1.2mm
JTC-5711 EXTRA LONG RETAINING RING PLIER (EXTERNAL STRAIGHT) Length: 225mm Tip length: 75mm Tip diameter: Ø1.2mm JTC-5712 EXTRA LONG RETAINING RING PLIER (EXTERNAL BENT) Length: 225mm Bent Tip length: 65mm Tip diameter: Ø1.2mm JTC-5713 12" EXTRA LONG NEEDLE NOSE PLIER Long jaws design for better reaching into recessed areas Length: 12" (300mm) Jaw length: 170mm
JTC-5714 7" WIRE CUTTER Applicable: Cable: Ø1.5mm, copper wire: Ø4mm. Length: 165mm JTC-5715 POWER RIBE BIT SET Bit material: S2 10 pcs 30mmL Ribe power bit: RM5, 6, 7, 8, 9, 10, 11, 12, 13, 14. 11 pcs 100mmL Ribe power bit: RM5, 6, 7, 8, 9, 10, 10.3, 11, 12, 13, 14. 2 pcs Adapter: 10mm (Hex) x 1/2"DR., 10mm(Hex) x 3/8" DR. JTC-5909 16" EXTRA LONG HANDLE NEEDLE NOSE PLIERS 0 Made from CR-MO material to provide a high strength level and uniform hardness. Handles with a diameter of 8mm and a tapered working part provide high functionality of the tool. Long, slim jaws and flash-riveted enable pliers to reach into recessed areas. Spec: Straight Length: 16"
JTC-5910 16" EXTRA LONG HANDLE NEEDLE NOSE PLIERS 45 Made from CR-MO material to provide a high strength level and uniform hardness. Handles with a diameter of 8mm and a tapered working part provide high functionality of the tool. Long, slim jaws and flash-riveted enable pliers to reach into recessed areas. Spec: 45 Bent Length: 16" JTC-19382 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 1/4" JTC-19385 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 5mm
JTC-19386 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 6mm JTC-19387 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 7mm JTC-19388 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 8mm
JTC-34258 HEAVY DUTY TWIN COLOR DIAGONAL PLIERS Made from CR-MO to provide a high strength level and uniform hardness. Handle material made of PP+TPR for good grip. Spec: 8" JTC-193810 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 10mm JTC-342810 WATERPUMP PLIERS 10" Made from CR-V to provide a high strength level and uniform hardness. Handle material made from PVC. Spec: 10"
JTC-10WR 10" LOCKING PLIERS Chrome moly steel drop forged jaws. Bodily heat-treated, welding brazed. Nickel plated. Spec: 10" Function: Includes knife. JTC-11R LOCKING "C" CLAMP CR-MO drop forget jaws. Bodily heat-treated. Welding brazed. Nickel plated. Spec: 11" Function: C shaped plier JTC-18R LOCKING "C" CLAMP CR-MO drop forget jaws. Bodily heat-treated. Welding brazed. Nickel plated. Spec: 18" Function: C shaped plier
JTC-20R 20" LOCKING CHAIN PLIER Chain length: 19" CR-MO jaws. Bodily heat-treated. Nickel plated. Function: Adjustable chain use to clip things. JTC-3210S 50 PCS GO THROUGH SCREWDRIVER SET 50 pcs The set could be hanged on the display board. JTC-3470S 44 PCS HEAVY DUTY SCREWDRIVER SET 44 pcs The set could be hanged on the display board.
JTC-5WR 5" LOCKING PLIERS Chrome moly steel drop forged jaws. Bodily heat-treated, welding brazed. Nickel plated. Spec: 5" Function: Includes knife JTC-6LN LONG NOSE LOCKING PLIERS Chrome moly steel drop forged jaws. Heat-treated jaws. Nickel plated. Spec: 6" Function: Includes sharp knife JTC-7WR LOCKING PLIERS Chrome moly steel drop forged jaws. Bodily heat-treated, welding brazed. Nickel plated. Spec: 7" Function: Includes knife.
JTC-8R 8" WELDING CLAMP Size: 8" CR-MO jaws Bodily heat-treated. Welding brazed. Nickel plated. Function: Clips things by the two flat pieces in front of the clamp. JTC-9LN LONG NOSE LOCKING PLIERS Chrome moly steel drop forged jaws. Heat-treated jaws. Nickel plated. Spec: 9" Function: Includes sharp knife JTC-9R 9" WELDING CLAMP Size: 9" CR-MO jaws Bodily heat-treated. Welding brazed. Nickel plated. Function: U-shaped jaws allow access and perfect visibility when welding.
JTC-HB175 RETAINING RING PLIERS Made from CR-V to provide a high strength level and uniform hardness. Spec: Internal 90 Length: 175mm JTC-HB230 RETAINING RING PLIERS Made from CR-V to provide a high strength level and uniform hardness. Spec: Internal 90 Length: 230mm JTC-HB300 RETAINING RING PLIERS Made from CR-V to provide a high strength level and uniform hardness. Spec: Internal 90 Length: 300mm
JTC-HS175 RETAINING RING PLIERS Made from CR-V to provide a high strength level and uniform hardness. Spec: Internal straight Length: 175mm JTC-HS230 RETAINING RING PLIERS Made from CR-V to provide a high strength level and uniform hardness. Spec: Internal straight Length: 230mm JTC-HS300 RETAINING RING PLIERS Made from CR-V to provide a high strength level and uniform hardness. Spec: Internal straight Length: 300mm
JTC-K5044 4 PCS HEAVY DUTY SNAP RING PLIERS SET Items: 5401 ~ 5404 1 pc Heavy Duty Internal straight 1 pc Heavy Duty Internal 90 1 pc Heavy Duty External straight 1 pc Heavy Duty External 90 JTC-SB175 RETAINING RING PLIERS Made from CR-V to provide a high strength level and uniform hardness. Spec: External 90 Length: 175mm JTC-SB230 RETAINING RING PLIERS Made from CR-V to provide a high strength level and uniform hardness. Spec: External 90 Spec: 230mm
JTC-SB300 RETAINING RING PLIERS Made from CR-V to provide a high strength level and uniform hardness. Spec: External 90 Length: 300mm JTC-SS175 RETAINING RING PLIERS Made from CR-V to provide a high strength level and uniform hardness. Spec: External straight Length: 175mm JTC-SS230 RETAINING RING PLIERS Made from CR-V to provide a high strength level and uniform hardness. Spec: External straight Length: 230mm
JTC-SS300 RETAINING RING PLIERS Made from CR-V to provide a high strength level and uniform hardness. Spec: External straight Length: 300mm JTC-U11MC 11 PCS MINI RATCHET BIT SET T10H, T15H, T20H, T25H, T27H, T30H, T40H #1, #2 6 mm