Test Report No.: xx001 Page 1 of xx Issue Date: DD/MM/YYYY Manufacturer: Applicant s Name Applicant s address Test item: Set Top Box Identification: (Model No.) Serial No.: Receipt No.: Date of receipt: Testing laboratory and its address: Lab Name Lab address Test specification: IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / IEC 60950-1: 2005 + A1: 2009 + A2 : 2013 Test Result: The test item passed / failed the test specification(s). Other Aspects: - Brief description or additional details could be given by the labs here. This test report relates to the test sample submitted and list of documents attached. Tested by: Approved by / Authorized Signatory: Issued by: (Name / Designation) (Name / Designation) (Name / Designation) Date: Date: Date:
TEST REPORT IS 13252 (Part 1): 2010 + A1: 2013+ A2: 2015 / IEC 60950-1: 2005 + A1: 2009 + A2: 2013 Information technology equipment Safety Part 1: General requirements Set Top Box Report Reference No.... : xxxxxxxxx 001 Date of issue... : Total number of pages... Testing Laboratory... : Address... : (see cover page) (see cover page) Lab Name Lab address Manufacturer s name... : Address... : Applicant s Name Applicant s address Test specification: Standard... : IS 13252 (Part 1): 2010 + A1: 2013+ A2:2015 / IEC 60950-1: 2005 + A1: 2009 +A2:2013 Test procedure... : Non-standard test method..: Test Report Form No.... : Test Report Form(s) Originator... : Compliance Report N/A Master TRF... : 03/06/2016 Test item description... : Trade Mark... : Model/Type reference... : Ratings... : Other Documents submitted... : BIS_IT/STB_IS13252_V1.4 Bureau of Indian Standards Set Top Box Please refer to Table List of Attachments at Page No. xx Tested by: Approved by / Authorized Signatory: Issued by: (Name / Designation) (Name / Designation) (Name / Designation) Date: Date: Date:
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 3 of 95 Test Code Description Measurement/ testing Total No. of tests Total no. of applicable tests/ Req. No. of tests/ Req. passed Page No. EL 2100 General Requirements Components (Cl.1.5) EL 2101 General Requirements Power interface (Cl.1.6) EL 2102 Marking Requirements Marking & instructions(cl.1.7) EL 2103 Electrical safety Protection from electric shock and energy hazards (Cl.2.1) EL 2104 Electrical safety SELV Circuits (Cl.2.2) EL 2105 Electrical safety TNV Circuits (Cl.2.3) EL 2106 Electrical safety Limited current circuits (Cl.2.4) EL 2107 Electrical safety Limited Power sources (Cl.2.5) EL 2108 Electrical safety Provisions for earthing and bonding (Cl.2.6) EL 2109 Electrical safety Overcurrent and earth fault protection in primary circuits (Cl.2.7) EL 2110 Electrical safety Safety Interlocks (Cl.2.8) EL 2111 Electrical safety Electrical Insulation (Cl.2.9) EL 2112 Electrical safety Clearances, Creepage distances and distances through insulation (Cl.2.10) EL 2113 Wiring Wiring, connections and supply (Cl.3) EL 2114 Wiring Connection to a main supply (Cl.3.2) EL 2115 Wiring Wiring terminals for connection of external conductors (Cl.3.3) EL 2116 Wiring Disconnection for the main supply (Cl.3.4) EL 2117 Wiring Interconnection of equipment (Cl.3.5) EL 2118 Mechanical properties Stability (Cl.4.1) EL 2119 Mechanical properties Mechanical strength (Cl.4.2)
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 4 of 95 EL 2120 EL 2121 EL 2122 EL 2123 Mechanical properties Mechanical properties Thermal Properties Mechanical properties Design and construction (Cl.4.3) Protection against hazardous moving parts (Cl.4.4) Thermal requirements (Cl.4.5) Openings in Enclosures (Cl.4.6) EL 2124 Fire Safety Resistance to fire (Cl.4.7) EL 2125 EL 2126 EL 2127 EL 2128 EL 2129 EL 2130 EL 2131 Insulating properties Insulating properties Insulating properties Communicating connection Communicating connection Communicating connection Connection to cable distribution systems Electrical requirements and simulated abnormal conditions(cl.5),5.1 Electric Strength (Cl.5.2) Abnormal operating and fault conditions (Cl.5.3) Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment(cl.6.1) Protection of equipment users from overvoltages on telecommunication networks (Cl.6.2) Protection of the telecommunication wiring system from overheating (Cl.6.3) Connection to cable distribution systems (Cl.7) EL 2132 Fire safety Tests for resistance to heat and fire (Annex A) EL 2133 Insulating properties Motor tests under abnormal conditions (Annex B) EL 2134 Electrical Safety Transformers (Annex C) EL 2135 EL 2136 Insulating properties Thermal Properties Measuring Instruments For Touch-Current Tests (Annex D) Temperature Rise Of A Winding(Annex E)
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 5 of 95 EL 2137 Electrical safety Measurement Of Clearances And Creepage Distances(Annex F) EL 2138 Electrical safety Alternative Method For Determining Minimum Clearances(Annex G) EL 2139 Radiation Safety Ionizing Radiation(Annex H) EL 2140 Electrical Safety Table of electrochemical potentials (Annex J) EL 2141 EL 2142 General Requirements General Requirements Thermal controls (Annex K) Normal load conditions for some types of electrical business equipment (Annex L) EL 2143 Electrical Safety Criteria for telephone ringing signals (Annex M) EL 2144 Electrical safety Impulse Test Generators(Annex N) EL 2145 EL 2146 EL 2147 EL 2148 EL 2149 General Requirements General Requirements General Requirements General Requirements Protection against Ingress of water Normative References(Annex P) Voltage dependent resistors (VDRs) (Annex Q) Examples Of Requirements For Quality Control Programmes(Annex R) Procedure For Impulse Testing (Annex S) Guidance On Protection Against Ingress Of Water (Annex T) EL 2150 Wiring Insulated Winding Wires For Use Without Interleaved Insulation (Annex U) EL 2151 EL 2152 EL 2153 Electrical Safety Electrical Safety Electrical Safety Ac Power Distribution Systems(Annex V) Summation Of Touch Currents (Annex W) Maximum Heating Effect In Transformer Tests(Annex X)
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 6 of 95 EL 2154 Radiation safety Ultraviolet light conditioning test (Annex Y) EL 2155 Electrical Safety Overvoltage Categories (Annex Z) EL 2156 Mechanical properties Mandrel Test(Annex AA) EL 2157 Electrical Safety Changes In The Second Edition(Annex BB) EL 2158 Electrical Safety Evaluation Of Integrated Circuit (IC) Current Limiters (Annex CC) EL 2159 EL 2160 Mechanical properties Electrical Safety Requirements For The Mounting Means Of Rack-Mounted Equipment (Annex DD) Household And Home/Office Document/Media Shredders (Annex EE) Certificate: It is certified that the above tests were performed and found to be passing/failing in the
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 7 of 95 Copy of marking plate: Copy of marking label:
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 8 of 95 Table List of Attachments Attachment No. Attachment Description No. of pages in Attachment Attachment 1 Photo Document xx General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. Possible test case verdicts: - test case does not apply to the test object... : N/A - test object does meet the requirement... : P (Pass) - test object does not meet the requirement... : F (Fail) Testing... : Date of receipt of test item... : Date(s) of performance of tests... : Laboratory conditions... : Ambient Temperature... : Ambient Humidity... :
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 9 of 95 Test item particulars... : Equipment mobility... : movable hand-held transportable stationary for building-in direct plug-in Connection to the mains... : Operating condition... : Access location... : pluggable equipment [] type A [] type B permanent connection detachable power supply cord non-detachable power supply cord not directly connected to the mains continuous rated operating / resting time: operator accessible restricted access location Over voltage category (OVC)... : OVC I OVC II OVC III OVC IV other: Mains supply tolerance (%) or absolute mains supply values... : -10%, +6% <OR> ±10% Class of equipment... : Class I Class II Class III Not classified Considered current rating of protective device as a part of the building installation (A)... : 16A (for India) Pollution degree (PD)... : PD 1 PD 2 PD 3 IP protection class... : IPXX or Not rated, indoor use only Altitude during operation (m)... : Up to 2000 Altitude of test laboratory (m)... : < 1000 Mass of equipment (kg)... : Abbreviations that may be used throughout this test report: PE/PB... : protective earth/protective bonding Pri...: primary CB... : circuit breaker sec...: secondary (SW)PS... : (switching) power supply gnd...: ground HV... : high voltage I/O...: input/output PCB... : printed circuit (wiring) board ii... : installation instruction TIW... : triple insulated wire PSU... : Power Supply Unit B/I... : built-in application (compliance shall be guarantee in host equipment) F/B/S/R : Functional/Basic/Supplementary/Reinforced Insulation
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 10 of 95 General product information: 1) Application details / Description of the product: Max. specified ambient temperature ( C)... :?? C Laser classification...... : < delete this line, if not applicable > 2) Differences between the models: (N/A, one single model) <OR> < describe the constructional differences in such general terms, that the informed reader can still make a rough evaluation of their safety relevance > Model No. tested with-in the family series. :?? 3) Options: The equipment was tested without any optional accessory installed. Hence, this report does not cover parameters that are influenced by the installation of optional accessory that might affect safety in the meaning of this standard.
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 11 of 95 Tests relating to General Requirements EL 2100 V1.4 1.5 Components* EL 2100-00 1.5.1 General: EL 2100-01 Components shall be complying with IEC 60950-1 or relevant component standard. Components and subassemblies approved for IEC 62368-1 can be considered as complying with this standard 1.5.2 Evaluation and testing of components EL 2100-02 1.5.3 Thermal controls EL 2100-03 1.5.4 Transformers EL 2100-04 1.5.5 Interconnecting cables* EL 2100-05 1.5.6 Capacitors bridging insulation * EL 2100-06 1.5.7 Resistors bridging insulation EL 2100-07 1.5.7.1 Resistors bridging functional, basic or supplementary insulation* EL 2100-08 1.5.7.2 Resistors bridging double or EL 2100-09 reinforced insulation between a.c. mains and other circuits 1.5.7.3 Resistors bridging double insulation or reinforced insulation between the a.c. mains supply and circuits connected to an antenna or coaxial cable 1.5.8 Components in equipment for IT power distribution systems* EL 2100-10 EL 2100-11 1.5.9 Surge suppressors EL 2100-12 1.5.9.1 General* EL 2100-13 1.5.9.2 Protection of VDRs* EL 2100-14 1.5.9.3 Bridging of functional insulation by a VDR* 1.5.9.4 Bridging of basic insulation by a VDR* 1.5.9.5 Bridging of supplementary, double or reinforced insulation by a VDR* EL 2100-15 EL 2100-16 EL 2100-17
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 12 of 95 Certificate: It is certified that the above tests were performed and found to be passing/ failing in the
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 13 of 95 Tests relating to Electrical Safety EL 2101 V1.4 1.6 Power interface* EL 2101-00 1.6.1 AC power distribution systems* EL 2101-01 1.6.2 Input current EL 2101-02 1.6.3 Voltage limit of hand-held equipment* EL 2101-03 1.6.4 Neutral conductor * EL 2101-04 Certificate: It is certified that the above tests were performed and found to be passing/ failing in the
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 14 of 95 Tests relating to Marking Requirements EL 2102 V1.4 1.7 Marking and instructions* EL 2102-00 1.7.1 Power rating and identification markings 1.7.1.1 Power rating marking* EL 2102-01 Rated voltage(s) or voltage ranges(s) (V)*. Multiple mains supply connections*. Symbol for nature of supply, for d.c. only*: Rated frequency or rated frequency range (Hz) *: EL 2102-02 EL 2102-03 EL 2102-04 EL 2102-05 Rated current (ma or A)*: EL 2102-06 1.7.1.2 Identification markings* EL 2102-07 Manufacturer s name or trademark or identification mark *: Model identification or type reference *: Symbol for Class II equipment only* : EL 2102-08 EL 2102-09 EL 2102-10 Other markings and symbols*: EL 2102-11 1.7.1.3 Use of graphical symbols* EL 2102-12 1.7.2 Safety instructions and marking* EL 2102-13 1.7.2.1 General EL 2102-14 1.7.2.2 Disconnect devices* EL 2102-15 1.7.2.3 Overcurrent protective devices* EL 2102-16 1.7.2.4 IT power distribution systems* EL 2102-17 1.7.2.5 Operator access with a tool* EL 2102-18 1.7.2.6 Ozone* EL 2102-19 1.7.3 Short duty cycles* EL 2102-20 1.7.4 Supply voltage adjustment* EL 2102-21 1.7.5 Power outlets on the equipment* EL 2102-22 1.7.6 Fuse identification (marking, special fusing characteristics, cross-reference) Fuse(s) shall clearly and adequately marked with fuse number and rating*. EL 2102-23 1.7.7 Wiring terminals EL 2102-24
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 15 of 95 Tests relating to Marking Requirements EL 2102 V1.4 1.7.7.1 Protective earthing and bonding terminals* 1.7.7.2 Terminals for a.c. mains supply conductors* 1.7.7.3 Terminals for d.c. mains supply conductors* EL 2102-25 EL 2102-26 EL 2102-27 1.7.8 Controls and indicators EL 2102-28 1.7.8.1 Identification, location and marking *: EL 2102-29 1.7.8.2 Colours* EL 2102-30 1.7.8.3 Symbols according to IEC 60417*: EL 2102-31 1.7.8.4 Markings using figures* : EL 2102-32 1.7.9 Isolation of multiple power sources* 1.7.10 Thermostats and other regulating devices* EL 2102-33 EL 2102-34 1.7.11 Durability EL 2102-35 1.7.12 Removable parts* EL 2102-36 1.7.13 Replaceable batteries* EL 2102-37 Language(s) 1.7.14 Equipment for restricted access locations* EL 2102-38
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 16 of 95 Tests relating to Electrical Safety EL 2103 V1.4 2.1 Protection from electric shock and energy hazards* EL 2103-00 2.1.1 Protection in operator access areas* EL 2103-01 2.1.1.1 Access to energized parts EL 2103-02 Test by inspection : Test with test finger (Figure 2A) Test with test pin (Figure 2B): Test with test probe (Figure 2C) 2.1.1.2 Battery compartments * EL 2103-03 2.1.1.3 Access to ELV wiring EL 2103-04 Working voltage (Vpeak or Vrms); minimum distance through insulation (mm) 2.1.1.4 Access to hazardous voltage circuit wiring EL 2103-05 2.1.1.5 Energy hazards : EL 2103-06 2.1.1.6 Manual controls EL 2103-07 2.1.1.7 Discharge of capacitors in equipment Measured voltage (V); time-constant (s): EL 2103-08 2.1.1.8 Energy hazards d.c. mains supply a) Capacitor connected to the d.c. mains supply : b) Internal battery connected to the d.c. mains supply : 2.1.1.9 Audio amplifiers to be tested according to IEC 60065, cl. 9.1.1.: EL 2103-09 EL 2103-10 EL 2103-11 2.1.2 Protection in service access areas EL 2103-12 2.1.3 Protection in restricted access locations EL 2103-13
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 17 of 95 Tests relating to Electrical Safety EL 2104 V1.4 2.2 SELV circuits* EL 2104-00 2.2.2 Voltages under normal conditions EL 2104-01 2.2.3 Voltages under fault conditions EL 2104-02 2.2.4 Connection of SELV circuits to other circuits* : EL 2104-03
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 18 of 95 Tests relating to Electrical Safety EL 2105 V1.4 2.3 TNV circuits* EL 2105-00 2.3.1 Type of TNV circuits: TNV-1 / TNV-2 / TNV-3 EL 2105-01 a) Limits of TNV-1: EL 2105-02 b) Limits of TNV-2 or TNV-3: Continuous voltages, combination of AC and DC values, are such that : EL 2105-03 2.3.2 Separation from other circuits and from accessible parts* EL 2105-04 2.3.2.1 General Requirements EL 2105-05 2.3.2.2 Protection by basic insulation EL 2105-06 2.3.2.3 Protection by earthing EL 2105-07 2.3.2.4 Protection by other constructions : 2.3.3 Separation from hazardous voltages 2.3.4 Connection of TNV circuits to other circuits 2.3.5 Test for operating voltages generated externally EL 2105-08 EL 2105-09 EL 2105-10 EL 2105-11
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 19 of 95 Tests relating to Electrical Safety EL 2106 V1.4 2.4 Limited current circuits * EL 2106-00 2.4.1 General requirements * EL 2106-01 2.4.2 Limit values EL 2106-02 2.4.3 Connection of limited current circuits to other circuits* EL 2106-03
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 20 of 95 Tests relating to Electrical Safety EL 2107 V1.4 2.5 Limited power sources * EL 2107-00 a) Inherently limited output EL 2107-01 b) Impedance limited output EL 2107-02 c) Regulating network limited output under normal operating and single fault condition Use of integrated circuit (IC) current limiters d) Overcurrent protective device limited output Max. output voltage (V), Max. output current (A), Max. apparent power (VA) Current rating of overcurrent protective device (A) EL 2107-03 EL 2107-04 EL 2107-05 EL 2107-06 (See Annex CC) 01 06
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 21 of 95 Tests relating to Electrical Safety EL 2108 V1.4 2.6 Provisions for earthing and bonding* EL 2108-00 2.6.1 Protective earthing EL 2108-01 2.6.2 Functional earthing : The Functional earthing either separated from hazardous voltages by double or reinforced insulation or by protectively earthed screen or conductive part separated by at least basic insulation, or safely connected to Protective Bonding Conductor.* Use of symbol for functional earthing:* 2.6.3 Protective earthing and protective bonding conductors* 2.6.3.2 Size of protective earthing conductors EL 2108-02 EL 2108-03 EL 2108-04 EL 2108-05 Rated current (A), cross-sectional area (mm2), 2.6.3.3 Size of protective bonding conductors EL 2108-06 Protective current Rating (A), crosssectional area (mm2) 2.6.3.4 Resistance of earthing conductors and their terminations; resistance ( ), voltage drop (V), test current (A), duration (min): EL 2108-07 2.6.3.5 Colour of insulation*: EL 2108-08 2.6.4 Terminals 2.6.4.2 Protective earthing and bonding terminals : Rated current(a), Type, Nominal thread diameter (mm) 2.6.4.3 Separation of the protective earthing conductor from protective bonding conductors* EL 2108-09 EL 2108-10 2.6.5 Integrity of protective earthing* 2.6.5.1 Interconnection of equipment* EL 2108-11 2.6.5.2 Components in protective earthing conductors and protective bonding conductors* EL 2108-12 2.6.5.3 Disconnection of protective earth* EL 2108-13 2.6.5.4 Parts that can be removed by an operator* EL 2108-14 2.6.5.5 Parts removed during servicing* EL 2108-15
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 22 of 95 2.6.5.6 Corrosion resistance* EL 2108-16 2.6.5.7 Screws for protective bonding* EL 2108-17 2.6.5.8 Reliance on telecommunication network or cable distribution system* EL 2108-18
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 23 of 95 Tests relating to Electrical Safety EL 2109 V1.4 2.7 Overcurrent and earth fault protection in primary circuits* 2.7.1 Basic requirements: Protection in primary circuits against overcurrents, shortcircuits and earth faults shall be provided, either as an integral part of the equipment or as part of building installation. EL 2109-00 EL 2109-01 If pluggable equipment Type B or permanently connected equipment relies on protective device external to the equipment for protection, the equipment installation Instructions shall so state and shall also specify the requirements for short-circuit protection or overcurrent protection or, where necessary, for both. 2.7.2 Faults not simulated in 5.3.7* need not be fitted as an integral part of the equipment EL 2109-02 2.7.3 Short-circuit backup protection EL 2109-03 2.7.4 Number and location of protective devices : EL 2109-04 2.7.5 Protection by several devices* EL 2109-05 2.7.6 Warning to service personnel* : EL 2109-06
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 24 of 95 Tests relating to Electrical Safety EL 2110 V1.4 2.8 Safety Interlocks* EL 2110-00 2.8.1 General principles* EL 2110-01 2.8.2 Protection requirements EL 2110-02 2.8.3 Inadvertent reactivation EL 2110-03 2.8.4 Fail-safe operation EL 2110-04 2.8.5 Moving parts EL 2110-05 2.8.6 Overriding* EL 2110-06 2.8.7 Switches, relays and their related circuits 2.8.7.1 Separation distances for contact gaps and their related circuits` EL 2110-07 EL 2110-08 2.8.7.2 Overload test EL 2110-09 2.8.7.3 Endurance test EL 2110-10 2.8.7.4 Electric strength test EL 2110-11 2.8.8 Mechanical actuators EL 2110-12
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 25 of 95 Tests relating to Electrical Safety EL 2111 V1.4 2.9 Electrical insulation* EL 2111-00 2.9.1 Properties of insulating materials* EL 2111-01 2.9.2 Humidity conditioning EL 2111-02 Relative Humidity : 93 ±3 %, Temperature: t at 40 ± 2 C Duration : 120 hours 2.9.3 Grade of insulation* EL 2111-03 2.9.4 Separation from hazardous voltages* EL 2111-04 Method(s) used
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 26 of 95 Tests relating to Electrical Safety EL 2112 V1.4 2.10 Clearances, creepage distances and distances through Insulation* EL 2112-00 2.10.1.1 Frequency * EL 2112-01 2.10.1.2 Pollution degrees* EL 2112-02 2.10.1.3 Reduced values for functional insulation 2.10.1.4 Intervening unconnected conductive parts EL 2112-03 EL 2112-04 2.10.1.5 Insulation with varying dimensions EL 2112-05 2.10.1.6 Special separation requirements EL 2112-06 2.10.1.7 Insulation in circuits generating starting pulses EL 2112-07 2.10.2 Determination of working voltage EL 2112-08 2.10.2.2 RMS working voltage EL 2112-09 2.10.2.3 Peak working voltage EL 2112-10 2.10.3 Clearances EL 2112-11 2.10.3.1 General EL 2112-12 2.10.3.2 Mains transient voltages* a) AC mains supply * : EL 2112-13 b) Earthed d.c. mains supplies*... EL 2112-14 c) Unearthed d.c. mains supplies* : EL 2112-15 d) Battery operation* : EL 2112-16 2.10.3.3 Clearances in primary circuits EL 2112-17 2.10.3.4 Clearances in secondary circuits EL 2112-18 2.10.3.5 Clearances in circuits having starting pulses EL 2112-19 2.10.3.6 Transients from a.c. mains supply : EL 2112-20 2.10.3.7 Transients from d.c. mains supply : EL 2112-21 2.10.3.8 Transients from telecommunication EL 2112-22 networks and cable distribution systems... 2.10.3.9 Measurement of transient voltages a) Transients from a mains supply EL 2112-23 For an a.c. mains supply For a d.c. mains supply b) Transients from a telecommunication network EL 2112-24
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 27 of 95 2.10.4 Creepage distances* EL 2112-25 2.10.4.1 General EL 2112-26 2.10.4.2 Material group and comparative tracking index : CTI tests* EL 2112-27 2.10.4.3 Minimum creepage distances EL 2112-28 2.10.5 Solid insulation EL 2112-29 2.10.5.1 General EL 2112-30 2.10.5.2 Distances through insulation EL 2112-31 2.10.5.3 Insulating compound as solid insulation EL 2112-32 2.10.5.4 Semiconductor devices EL 2112-33 2.10.5.5. Cemented joints EL 2112-34 2.10.5.6 Thin sheet material General EL 2112-35 2.10.5.7 Separable thin sheet material EL 2112-36 2.10.5.8 Non-separable thin sheet material EL 2112-37 2.10.5.9 Thin sheet material standard test procedure Electric strength test as per Cl.5.2.2 2.10.5.10 Thin sheet material alternative test procedure Electric strength test as per Cl.5.2.2 EL 2112-38 EL 2112-39 2.10.5.11 Insulation in wound components EL 2112-40 2.10.5.12 Wire in wound components If Peak Working voltage >71 V a) Basic insulation not under stress EL 2112-41 b) Basic, supplementary, reinforced insulation EL 2112-42 c) Compliance with Annex U EL 2112-43 d) Where two winding wires in contact inside wound component; angle between 45 and 90 2.10.5.13 Wire with solvent-based enamel in wound components a) Electric strength test (Type test as per Cl.5.2.2) b) Electric Strength test (Routine test as per Cl.5.2.2) 2.10.5.14 Additional insulation in wound components If Peak Working Voltage >71V EL 2112-44 EL 2112-45 EL 2112-46 a) Basic insulation not under stress EL 2112-47
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 28 of 95 b) Supplementary, reinforced insulation EL 2112-48 2.10.6 Construction of printed boards* 2.10.6.1 Uncoated printed boards EL 2112-49 2.10.6.2 Coated printed boards EL 2112-50 2.10.6.3 Insulation between conductors on the same inner surface of a printed board EL 2112-51 2.10.6.4 Insulation between conductors on different surfaces of a printed board* a) Minimum Thickness of insulation: 0.4mm or b) Confirm with one of the specification and pass the relevant tests as per Table 2R EL 2112-52 EL 2112-53 2.10.7 Component external terminations EL 2112-54 2.10.8 Tests on coated printed boards and coated components 2.10.8.1 Sample preparation and preliminary inspection* EL 2112-55 2.10.8.2 Thermal conditioning EL 2112-56 2.10.8.3 Electric strength test EL 2112-57 2.10.8.4 Abrasion resistance test EL 2112-58 2.10.9 Thermal cycling EL 2112-59 2.10.10 Test for Pollution Degree 1 environment and insulating compound 2.10.11 Tests for semiconductor devices and cemented joints EL 2112-60 EL 2112-61 2.10.12 Enclosed and sealed parts EL 2112-62 Total number of tests to be conducted :
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 29 of 95 Tests relating to Wiring EL 2113 V1.4 3.0 Wiring, connections and supply* EL 2113-00 3.1.1 Current rating and overcurrent protection 3.1.2 Protection against mechanical damage* EL 2113-01 EL 2113-02 3.1.3 Securing of internal wiring* EL 2113-03 3.1.4 Insulation of conductors EL 2113-04 3.1.5 Beads and ceramic insulators EL 2113-05 3.1.6 Screws for electrical contact pressure* 3.1.7 Insulating materials in electrical connections* 3.1.8 Self-tapping and spaced thread screws* 3.1.9 Termination of conductors : 10 N pull test EL 2113-06 EL 2113-07 EL 2113-08 EL 2113-09 3.1.10 Sleeving on wiring* EL 2113-10
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 30 of 95 Tests relating to Wiring EL 2114 V1.4 Cl. No. Test / Requirement name Test Code Test result/ observation Verdict 3.2 Connection to a mains supply* EL 2114-00 3.2.1 Means of connection 3.2.1.1 Connection to an a.c. mains supply* EL 2114-01 3.2.1.2 Connection to a d.c. mains supply* EL 2114-02 3.2.2 Multiple supply connections EL 2114-03 3.2.3 Permanently connected equipment EL 2114-04 3.2.4 Appliance inlets: Are so Located that parts at hazardous voltage are not accessible during insertion or removal of the connector, connector can be inserted without difficulty and after insertion of the connector, the equipment is not supported by the connector for any position of normal use on a flat surface ( appliance inlets complying with IEC 60309 or IEC 60320 considered to comply with this requirement. 3.2.5 Power supply cords EL 2114-05 3.2.5.1 AC power supply cords* EL 2114-06 Rated current (A), cross-sectional area (mm²), AWG 3.2.5.2 DC power supply cords* EL 2114-07 3.2.6 Cord anchorages and strain relief Mass of the equipment: Pull Force (N): EL 2114-08 b) Longitudinal displacement: 2 mm (Max) EL 2114-09 3.2.7 Protection against mechanical damage EL 2114-10 3.2.8 Cord guards a) Diameter or minor dimension D (mm) : Test mass (g) : EL 2114-11 b) Radius of curvature of cord : 1.5 D (Min) EL 2114-12 3.2.9 Supply wiring space EL 2114-13
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 31 of 95 Tests relating to Wiring EL 2115 V1.4 3.3 Wiring terminals for connection of external conductors* EL 2115-00 3.3.1 Wiring terminals* EL 2115-01 3.3.2 Connection of non-detachable power supply cords EL 2115-02 3.3.3 Screw terminals* EL 2115-03 3.3.4 Conductor sizes to be connected EL 2115-04 Rated current (A), cord/cable type, cross-sectional area (mm2) 3.3.5 Wiring terminal sizes EL 2115-05 Rated current (A), type, nominal thread diameter (mm) 3.3.6 Wiring terminal design EL 2115-06 3.3.7 Grouping of wiring terminals* EL 2115-07 3.3.8 Stranded wire EL 2115-08
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 32 of 95 Tests relating to Wiring EL 2116 V1.4 3.4 Disconnection from the mains supply* 3.4.1 General Requirement A disconnect device or devices shall be provided to disconnect the equipment from the mains supply for servicing. EL 2116-00 EL 2116-01 3.4.2 Disconnect devices* EL 2116-02 3.4.3 Permanently connected equipment* EL 2116-03 3.4.4 Parts which remain energized* EL 2116-04 3.4.5 Switches in flexible cords* EL 2116-05 3.4.6 Number of poles - single-phase and d.c. equipment* 3.4.7 Number of poles - three-phase equipment* EL 2116-06 EL 2116-07 3.4.8 Switches as disconnect devices* EL 2116-08 3.4.9 Plugs as disconnect devices* EL 2116-09 3.4.10 Interconnected equipment* EL 2116-10 3.4.11 Multiple power sources* EL 2116-11
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 33 of 95 Tests relating to Wiring EL 2117 V1.4 3.5 Interconnection of equipment* EL 2117-00 3.5.1 General requirements* EL 2117-01 3.5.2 Types of interconnection circuits* 3.5.3 ELV circuits as interconnection circuits * 3.5.4 Data ports for additional equipment EL 2117-02 EL 2117-03 EL 2117-04
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 34 of 95 Tests relating to Mechanical Properties EL 2118 V1.4 4 PHYSICAL REQUIREMENTS* EL 2118-00 4.1 Stability EL 2118-01 a) A unit having a mass of 7 kg or more shall not fall over when tilted to an angle of 10 from its normal upright position. Alternatively, the unit is placed in its intended position of use on a plane, inclined at an angle of 10 to the horizontal, and then rotated slowly through an angle of 360 about its normal vertical axis. b) A floor-standing unit having a mass of 25 kg or more shall not fall over when a force equal to 20 % of the weight of the unit, but not more than 250 N, is applied in any direction except upwards, at a height not exceeding 2 m from the floor. c) A floor-standing unit shall not fall over when a constant downward force of 800 N is applied at the point of maximum moment to any horizontal surface of at least 125 mm by at least 200 mm, at a height up to 1 m from the floor. EL 2118-02 EL 2118-03 EL 2118-04
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 35 of 95 Tests relating to Mechanical Properties EL 2119 V1.4 4.2 Mechanical Strength EL 2119-00 4.2.1 General EL 2119-01 4.2.2 Steady force test, 10 N EL 2119-02 4.2.3 Steady force test, 30 N EL 2119-03 4.2.4 Steady force test, 250 N EL 2119-04 4.2.5 Impact test EL 2119-05 a) Fall test as per Fig. 4A EL 2119-06 b) Swing test as per Fig. 4A EL 2119-07 4.2.6 Drop test; height (mm) : EL 2119-08 4.2.7 Stress relief test EL 2119-09 4.2.8 Cathode Ray Tubes EL 2119-10 4.2.9 High Pressure Lamps* EL 2119-11 4.2.10 Wall or ceiling mounted equipment; force(n) EL 2119-12
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 36 of 95 Tests relating to Mechanical Properties EL 2120 V1.4 4.3 Design and Construction* EL 2120-00 4.3.1 Edges and corners* EL 2120-01 4.3.2 Handles and manual controls; EL 2120-02 force (N)... 4.3.3 Adjustable controls EL 2120-03 4.3.4 Securing of parts EL 2120-04 4.3.5 Connections by Plugs and Sockets* EL 2120-05 4.3.6 Direct plug-in equipment EL 2120-06 Torque EL 2120-07 Compliance with the relevant mains plug standard 4.3.7 Heating elements in earthed equipment* EL 2120-08 EL 2120-09 4.3.8 Batteries Portable secondary sealed cells and batteries (other than button) containing alkaline or other non-acid electrolyte shall comply with IEC 62133 a) Overcharging of a rechargeable battery b) Unintentional charging of a non-rechargeable battery c) Reverse charging of a rechargeable battery d) Excessive discharging rate for any battery e) Electric strength as per Cl.5.3.9.2 EL 2120-10 EL 2120-11 EL 2120-12 EL 2120-13 EL 2120-14 4.3.9 Oil & grease* EL 2120-15 4.3.10 Dust, powders, liquids and gases EL 2120-16 4.3.11 Containers for liquids or gases EL 2120-17 4.3.12 Flammable liquids EL 2120-18 4.3.13 Radiation 4.3.13.2 Ionizing radiation EL 2120-19 4.3.13.3 Effect of ultraviolet (UV) radiation on materials EL 2120-20
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 37 of 95 4.3.13.4 Human exposure to ultraviolet (UV) radiation EL 2120-21 4.3.13.5 Lasers (including laser diodes) and LED s: 4.3.13.5.1 Lasers (including laser diodes) For laser see IEC 60825-1, respective part as applicable. EL 2120-22 Laser class... 4.3.13.5.2 Light emitting diodes (LED s) EL 2120-23 4.3.13.6 Other types* EL 2120-24
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 38 of 95 Tests relating to Mechanical Properties EL 2121 V1.4 4.4 Protection against hazardous moving parts EL 2121-00 4.4.1 General EL 2121-01 4.4.2 Protection in operator access areas 4.4.3 Protection in restricted access locations * 4.4.4 Protection in service access areas* 4.4.5 Protection against moving fan blades EL 2121-02 EL 2121-03 EL 2121-04 EL 2121-05 4.4.5.1 General* EL 2121-06 m = r = N = K = Not considered likely to cause pain or injury. a)...: Is considered likely to cause pain, not injury. b) Considered likely to cause injury. c).. : EL 2121-07 = EL 2121-08 = EL 2121-09 4.4.5.2 Protection for users* EL 2121-10 Use of symbol or warning* EL 2121-11 4.4.5.3 Protection for service persons* EL 2121-12 Use of symbol or warning * EL 2121-13
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 39 of 95 Tests relating to Thermal Properties EL 2122 V1.4 4.5 Thermal Requirements* EL 2122-00 4.5.1 General EL 2122-01 4.5.2 Temperature tests EL 2122-02 4.5.3 Temperature limits for materials* EL 2122-03 4.5.4 Touch temperature limits* EL 2122-04 4.5.5 Resistance to abnormal heat EL 2122-05
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 40 of 95 Tests relating to Mechanical Properties EL 2123 V1.4 4.6 Openings in enclosures* EL 2123-00 4.6.1 Top and side openings EL 2123-01 Dimensions (mm) : 4.6.2 Bottoms of fire enclosures : EL 2123-02 Construction of the bottom, dimensions (mm) : 4.6.3 Doors or covers in fire enclosures* 4.6.4 Openings in transportable equipment EL 2123-03 EL 2123-04 4.6.4.1 Constructional design measures EL 2123-05 Dimensions (mm) 4.6.4.2 Evaluation measures for larger openings EL 2123-06 4.6.4.3 Use of metallized parts EL 2123-07 4.6.5 Adhesives for constructional purposes: Compliance is checked by examination of the construction and of the available data. If such data is not available, compliance is checked by the following tests. a)temperature Conditioning at : 100 C ± 2 C for one week; or 90 C ± 2 C for three weeks; or 82 C ± 2 C for eight weeks. After temperature conditioning b) Leave the sample between 20 C to 30 C for 1 hour c) Place the sample at - 40 C±2 C for 4 hours d) Remove and allow the sample to come to any convenient temperature between 20 C and 30 C for 8 h; e) Place the sample in a cabinet at 91 % to 95 % relative humidity for 72 h; EL 2123-08 EL 2123-09 EL 2123-10 EL 2123-11 EL 2123-12 EL 2123-13
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 41 of 95 f) Remove the sample and leave it at any convenient temperature between 20 C and 30 C for 1 h; g) Place the sample in an oven at the temperature used for the temperature conditioning for 4 h; h) Remove the sample and allow it to reach any convenient temperature between 20 C; and 30 C for 8 h. i) The sample is then immediately subjected to the tests of Cl.4.2 as applicable. EL 2123-14 EL 2123-15 EL 2123-16 EL 2123-17
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 42 of 95 Tests relating to Fire Safety EL 2124 V1.4 4.7 Resistance to fire* EL 2124-00 4.7.1 Reducing the risk of ignition and spread of flame Method 1, selection and EL 2124-01 application of components wiring and materials OR Method 2, application of all of simulated fault condition tests 4.7.2 Conditions for a fire enclosure* EL 2124-02 4.7.2.1 Parts requiring a fire enclosure* EL 2124-03 4.7.2.2 Parts not requiring a fire enclosure EL 2124-04 4.7.3 Materials* EL 2124-05 4.7.3.1 General* EL 2124-06 a)class of material used* EL 2124-07 b) Where HB40 CLASS MATERIAL, HB75 CLASS MATERIAL or HBF CLASS FOAMED MATERIAL, is required, material passing the glow-wire test at 550 C according to IEC 60695-2-11 is acceptable as an alternative. c) Where it is not practical to protect components against overheating under fault conditions, the components shall be mounted on V-1 CLASS MATERIAL. Additionally, such components shall be separated from material of a class lower than V-1 CLASS MATERIAL by at least 13 mm of air, or by a solid barrier of V-1 CLASS MATERIAL. 4.7.3.2 Materials for fire enclosures a) For MOVABLE EQUIPMENT having a total mass not exceeding 18 kg, the material of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of V-1 CLASS MATERIAL or shall pass the test of Clause A.2. EL 2124-08 EL 2124-09 EL 2124-10
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 43 of 95 b) For MOVABLE EQUIPMENT having a total mass exceeding 18 kg and for all STATIONARY EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1. c) Materials for components that fill an opening in a FIRE ENCLOSURE, and that are intended to be mounted in this opening shall : be of V-1 CLASS MATERIAL; or pass the tests of Clause A.2; or comply with the flammability requirements of the relevant IEC component standard d) Plastic materials of a FIRE ENCLOSURE shall be located more than 13 mm through air from arcing parts such as unenclosed commutators and unenclosed switch contacts. e)plastic materials of a FIRE ENCLOSURE located less than 13mm through air from nonarcing parts which, under any condition of normal or abnormal operation,could attain a temperature sufficient to ignite the material, shall be capable of passing the test of IEC 60695-2- 20. The average time to ignition of the samples shall be not less than 15sec. If the sample melts through without igniting, the time at which this occurs is not considered to be the time to ignition. EL 2124-11 EL 2124-12 EL 2124-13 EL 2124-14 4.7.3.3 Materials for components and other parts outside fire enclosures *
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 44 of 95 a) Materials shall be of : HB75 CLASS MATERIAL if the thinnest significant thickness of this material is < 3 mm, or HB40 CLASS MATERIAL if the thinnest significant thickness of this material is 3 mm, or HBF CLASS FOAMED MATERIAL.* b) Connectors shall comply with one of the following: be made of V-2 CLASS MATERIAL; or pass the tests of Clause A.2; or comply with the flammability requirements of the relevant IEC component standard; or be mounted on V-1 CLASS MATERIAL and be of a small size; or be located in a SECONDARY CIRCUIT supplied by a power source that is limited to a maximum of 15 VA (see 1.4.11) under normal operating conditions and after a single fault in the equipment (see 1.4.14). EL 2124-15 EL 2124-16 4.7.3.4 Materials for components and other parts inside fire enclosures a) Inside FIRE ENCLOSURES, materials for components and other parts shall comply with one of the following: be of V-2 CLASS MATERIAL or HF-2 CLASS FOAMED MATERIAL; or pass the flammability test described in Clause A.2; or meet the flammability requirements of a relevant IEC component standard that includes such requirements. Requirements for voltage dependent resistors (VDR s) are in Annex Q.* EL 2124-17 EL 2124-18
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 45 of 95 4.7.3.5 Materials for air filter assemblies : Air filter assemblies shall be constructed of V-2 CLASS MATERIAL, or HF-2 CLASS FOAMED MATERIAL. EL 2124-19 4.7.3.6 Materials used in high-voltage components a) High-voltage components operating at peak-to-peak voltages exceeding 4 kv shall either be of V-2 CLASS MATERIAL, or HF-2 CLASS FOAMED MATERIAL, or comply with 14.4 of IEC 60065 or pass the needle flame test according to IEC 60695-11-5. b) Compliance is checked by inspection of the equipment and material data sheets and, if necessary, by the tests for V-2 CLASS MATERIAL or HF-2 CLASS FOAMED MATERIAL; or the test described in 14.4 of IEC 60065; or the needle flame test according to IEC 60695-11-5. c) In addition to above, the following details apply, referring to clauses of IEC 60695-11-5: Clause 7 - Severities EL 2124-20 EL 2124-21 EL 2124-22 Clause 8 - Conditioning EL 2124-23 Clause 11 - Evaluation of test results EL 2124-24
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 46 of 95 Tests relating to Insulating Properties EL 2125 V1.4 5.0 ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS* 5.1 Touch current and protective conductor current* 5.1.2 Configuration of equipment under test (EUT)* 5.1.2.1 Single connection to an a.c. mains supply* 5.1.2.2 Redundant multiple connections to an a.c. mains supply* 5.1.2.3 Simultaneous multiple connections to an a.c. mains supply EL 2125-00 EL 2125-01 EL 2125-02 EL 2125-03 EL 2125-04 EL 2125-05 5.1.3 Test circuit EL 2125-06 5.1.4 Application of measuring instrument EL 2125-07 5.1.5 Test procedure EL 2125-08 5.1.6 Test measurements a) r.m.s value of voltage, U2 measured using the instrument as per Fig. D.1 or r.m.s value of current measured using the instrument as per Fig. D.2 Alternatively, peak value of voltage, U2, is measured using the measuring instrument described in Clause D.1 EL 2125-09 b) Measured touch current (ma): EL 2125-10 c) Calculated value of TOUCH CURRENT (ma) = U2 / 500 d ) Measured protective conductor current(ma) e) Max. protective conductor current =5% of Input current 5.1.7 Equipment with touch current exceeding 3.5 ma EL 2125-11 EL 2125-12 EL 2125-13 EL 2125-14 5.1.7.1 General EL 2125-15 5.1.7.2 Simultaneous multiple connections to the supply EL 2125-16
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 47 of 95 5.1.8 Touch currents to telecommunication networks and cable distribution systems and from telecommunication networks 5.1.8.1 Limitation of the touch current to a telecommunication network or to a cable distribution system EL 2125-17 EL 2125-18 Supply voltage (V) Measured touch current (ma) Max. allowed touch current (ma) 5.1.8.2 Summation of touch currents from telecommunication networks EL 2125-19 a) EUT with earthed telecommunication ports : b) EUT whose telecommunication ports have no reference to protective earth
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 48 of 95 Tests relating to Insulating Properties EL 2126 V1.4 5.2 Electric strength* EL 2126-00 5.2.1 General* EL 2126-01 5.2.2 Test procedure a) The test voltages for electric strength for the appropriate grade of insulation [FUNCTIONAL INSULATION if required by 5.3.4 b), BASIC INSULATION, SUPPLEMENTARY INSULATION or REINFORCED INSULATION] are as specified in either: Table 5B using the PEAK WORKING VOLTAGE (U), as determined in 2.10.2; or Table 5C using the REQUIRED WITHSTAND VOLTAGE, as determined in G.4. EL 2126-02
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 49 of 95 Tests relating to Insulating Properties EL 2127 V1.4 5.3 Abnormal operating and fault conditions 5.3.1 Protection against overload and abnormal operation EL 2127-00 EL 2127-01 5.3.2 Motors EL 2127-02 5.3.3 Transformers EL 2127-03 5.3.4 Functional insulation: EL 2127-04 5.3.5 Electromechanical components EL 2127-05 5.3.6 Audio amplifiers in ITE : EL 2127-06 5.3.7 Simulation of faults EL 2127-07 5.3.8 Unattended equipment EL 2127-08 5.3.9 Compliance criteria for abnormal operating and fault conditions* 5.3.9.1 During the tests EL 2127-09 5.3.9.2 After the tests EL 2127-10
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 50 of 95 Tests relating to Communicating Connection EL 2128 V1.4 6.1 Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment 6.1.1 Protection from hazardous voltages EL 2128-00 EL 2128-01 6.1.2 Separation of the telecommunication network from earth* 6.1.2.1 Requirements: - Surge suppressors that bridge the insulation shall have a minimum rated operating voltage U op of U op =U peak + ΔU sp + ΔU sa EL 2128-02 Where U peak is 360V or 180V ΔU sp is the maximum increase of the rated operating voltage due to variations in component production(if not specified by the manufacturer, shall be taken as 10% of the rated operating voltage of the component) ΔU sa is the maximum increase of the rated operating voltage due to the component ageing over the expected life of the equipment(if not specified by the manufacturer, shall be taken as 10% of the rated operating voltage of the component) -Insulation is subjected to electric strength test according to 5.2.2. The a.c test voltage is 1.5kV or 1.0kV - Components bridging the insulation that are left in place during electric strength testing shall not be damaged. There shall be no breakdown of insulation during electric strength testing.
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 51 of 95 6.1.2.2 Exclusions EL 2128-03
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 52 of 95 Tests relating to Communicating Connection EL 2129 V1.4 6.2 Protection of equipment users from overvoltages on telecommunication networks* EL 2129-00 6.2.1 Separation requirements EL 2129-01 6.2.2 Electric strength test procedure EL 2129-02 6.2.2.1 Impulse test EL 2129-03 6.2.2.2 Steady-state test EL 2129-04 6.2.2.3 Compliance criteria EL 2129-05
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 53 of 95 Tests relating to Communicating Connection EL 2130 V1.4 6.3 Protection of the telecommunication wiring system from overheating a)if current limiting is due to the inherent impedance of the power source, the output current into any resistive load, including a short-circuit, is measured. The current limit shall not be exceeded after 60 s of test. Max. output current (A) : b) If current limiting is provided by an overcurrent protective device having a specified time/current characteristic: the time/current characteristic shall show that a current equal to 110 % of the current limit will be interrupted within 60 min; and EL 2130-00 EL 2130-01 EL 2130-02 c) the output current into any resistive load, including a shortcircuit, with the overcurrent protective device bypassed, measured after 60 s of test, shall not exceed 1 000/U, where U is the output voltage measured in accordance with 1.4.5 with all load circuits disconnected. EL 2130-03
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 54 of 95 d) If current limiting is provided by an overcurrent protective device that does not have a specified time/current characteristic: the output current into any resistive load, including a shortcircuit, shall not exceed the current limit after 60 s of test; and the output current into any resistive load, including a shortcircuit, with the overcurrent protective device bypassed, measured after 60 s of test, shall not exceed 1 000/U, where U is the output voltage measured in accordance with 1.4.5 with all load circuits disconnected. EL 2130-04
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 55 of 95 Tests relating to Connection to cable distribution system EL 2131 V1.4 7 Connection to cable distribution systems* EL 2131-00 7.1 General requirements* EL 2131-01 7.2 Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment 7.3 Protection of equipment users from overvoltages on the cable distribution system 7.4 Insulation between primary circuits and cable distribution systems EL 2131-02 EL 2131-03 EL 2131-04 7.4.1 General EL 2131-05 7.4.2 Voltage surge test EL 2131-06 7.4.3 Impulse test EL 2131-07
Report No. xxxxxx IS 13252 (Part 1): 2010 + A1: 2013 + A2 : 2015 / Page 56 of 95 Tests relating to Fire Safety EL 2132 V1.4 A ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE A.1 Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 kg, and of stationary equipment (see 4.7.3.2) EL 2132-00 EL 2132-01 A.1.1 Samples: EL 2132-02 A.1.2 Wall thickness (mm): Conditioning of samples; temperature ( C) : EL 2132-03 A.1.3 Mounting of samples : EL 2132-04 A.1.4 Test flame (see IEC 60695-11- 3) Flame A, B, C or D : EL 2132-05 A.1.5 Test procedure EL 2132-06 A.1.6 Compliance criteria EL 2132-07 Sample 1 burning time (s): Sample 2 burning time (s): Sample 3 burning time (s): A.2 Flammability test for fire enclosures of movable equipment having a total mass not exceeding 18 kg, and for material and components located inside fire enclosures (see 4.7.3.2 and 4.7.3.4) EL 2132-08 A.2.1 Samples, material: EL 2132-09 A.2.2 Wall thickness (mm): Conditioning of samples; temperature ( C) : EL 2132-10 A.2.3 Mounting of samples : EL 2132-11 A.2.4 Test flame (see IEC 60695-11- 4) Flame A, B or C : EL 2132-12 A.2.5 Test procedure EL 2132-13 A.2.6 Compliance criteria EL 2132-14 Sample 1 burning time (s):