LITECHECK2 HEADLAMP BEAM SETTER Litecheck2 Headlamp Beam Setter is specifically designed to meet 2005 VOSA specification and therefore can be used in ATL applications. Litecheck2 is for use in Class 1, 2, 3, 4 & 7 MOT test lanes where there is no testing of HGV. A 3 metre rail is supplied suitable for MOT installation as standard.
Dunlop DL526ATL Features 5.0 tonne capacity Play detector (VOSA approved) CE approved Warranty twelve months parts and labour Technical data Platform Length External Width Width between post Recessed depth Motor Optional 5700 mm 3230 mm 2850 mm 160 mm 3kw - 3 phase Single phase on request Application MOT Car service bays Brake repairs and service Suspension replacement Transmission repair and replacement Tyre shop General repair bay Shaker plates
Barker Buildings, Witt Road Telephone +44 (0)151 257 7700 BM9010 Brake Tester Several international authorities like MOT in the England approve the BM9010. The BM9010 is designed for workshop and vehicle inspection applications. The brake tester features a long range of options, which allows for a configuration, which can meet most customer requirements including: Infra Red remote control Pedal force measurement Test of 4x4 driven vehicles Automatic weighing system (BM9010 A only) Diagnostic/graphical printout without connection to PC Connection to local or remote PC with BM windows software Prepared for test line expansion including Suspension tester, Speedometer tester and side slip tester all controlled from same electronics with results shown on same display. Electronic scales for both refrigerant and oil. Automatic oil injection. Automatic leak detection, a buzzer sounds if a vacuum cannot be held during the test cycle. Built in printer. 12 months parts and labour warranty. CE Approved.
Barker Buildings, Witt Road Telephone +44 (0)151 257 7700 The BM9010 is equipped with same electronics and software as the other BM brake tester models for light vehicles BM3010, BM7010 and BM8010 and therefore the BM9010 offers same high test standard and data processing as these models. The design of BM9010 is made to a very high standard both in terms of quality and safety. All steel is hot galvanised and the wear surface of rollers is based on mesh steel to ensure long lifetime and accurate measurement. As standard the BM9010 is supplied with hot galvanised sub-frames, which are concreted into the ground before the actual brake tester is installed. The subframes make the planning and implementation of installations much easier and do also ensure correct alignment of the brake tester during concreting. The BM9010 can be supplied with a PDA solution, which allows operator to control and monitor the test results live directly on a PDA unit. Advantage and benefit The split bed concept has the advantage over a one-roller bed concept that it can be installed over an inspection pit. The roller bed is designed to maximize the protection of the wheels and chassis of the vehicle being tested. Cover plates around the rollers are all angled on the BM9010 B model, so the tyre is protected from damage should it the cover plates. All gaps are minimised in order to maximise the protection of the operator. The rollers are raised over floor level, which ensures, that vehicle is tested with all 4 wheels in floor level. The raised rollers also reduce the risk of damaging skirts and spoilers while entering and exiting the roller bed. The BM9010 is as standard supplied with a display having two large analogue readings of brake force left and right and 50 mm high bright digital readout of brake force imbalance. The BM9010 A is as standard supplied with 5 kw gear motors and therefore it has a double range brake force scale: Low scale 0-750 dan/kgf High scale 0-1500 dan/kgf When configured with suspension tester and side slip, then these gauges and the digital imbalance window is used to display the test result from this equipment. Optionally the BM9010 can be supplied with a special windows based BM display, which additional has 50 mm high bright digital readout of ovality, pedal force, weight, efficiency, suspension values, and speed and distance values. The display can be mounted either on the wall saving floor space or on floor column devices. The BM9010 can be supplied in a minimum configuration and still allows for later upgrade to all options. This means that in case customer later wants to upgrade to a higher specification due to new legislation or other, then customer will not experience, that he has to purchase another brake tester. As standard the BM9010 software allows for advanced graphical printout enabling the customer to perform both pre inspection brake tests and diagnosing before repair brake tests. This advanced printout of test results can be done without having to connect a PC to the brake tester. The BM9010 can be configured to run BM Windows Software programs installed on a PC. This PC can replace the analogue display or it can be an addon installed in the workshop office. The Windows program allows for advanced storing and presentation of test results using SQL database technology. Applications The BM9010 A model is used in workshops testing light vehicles as well as vans and city trucks up to axle load of 5000 kg. The rollers have same length as a normal heavy vehicle brake tester, 1000 mm and the gear motor is 5.0 kw in order to ensure sufficient power when testing vans and light city trucks. The BM9010 B model is specially designed and used by the Government owned vehicle inspection bodies in Iceland, Sweden and Denmark. The roller bed is properly the strongest in the market for vehicles up to 3.500 kg axle load and designed for very high throughput combined with minimal downtime and maximum lifetime.