4 EXTERIOR FRONT BUMPER DISASSEMBLY 1. REMOVE HOOD TO FRONT END PANEL SEAL (a) Using a clip remover, detach the 8 clips and remove the panel seal. 2. REMOVE FRONT BUMPER REINFORCEMENT (a) Using a clip remover, remover the 2 clips and reinforcement from the bumper cover. 3. REMOVE RADIATOR GRILLE LOWER 4. REMOVE FRONT BUMPER HOLE COVER 5. REMOVE FRONT BUMPER GUARD COVER LH (a) Using a screwdriver, detach the 3 claws and remove the cover. Tape the screwdriver tip before use. 6. REMOVE FRONT BUMPER GUARD COVER RH Use the same procedures described for the LH side. B084360E01 B084360E01 REASSEMBLY 1. INSTALL FRONT BUMPER GUARD COVER LH (a) Attach the 3 claws to install the cover. 2. INSTALL FRONT BUMPER GUARD COVER RH Use the same procedures described for the LH side. 3. INSTALL FRONT BUMPER HOLE COVER 4. INSTALL RADIATOR GRILLE LOWER 5. INSTALL FRONT BUMPER REINFORCEMENT (a) Install the reinforcement to the bumper cover with the 2 clips. 6. INSTALL HOOD TO FRONT END PANEL SEAL (a) Attach the 8 clips to install the panel seal.
EXTERIOR FRONT BUMPER 5 Protective Tape B084361E01 INSTALLATION A bolt without a torque specification is shown in the standard bolt chart (see page SS-2). 1. INSTALL FRONT BUMPER SIDE SUPPORT LH (a) Attach the 2 clips to install the side support. (b) Install the screw and bolt. Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) for screw 12 N*m (122 kgf*cm, 9 ft.*lbf) for bolt 2. INSTALL FRONT BUMPER SIDE SUPPORT RH (a) (b) Attach the 2 clips to install the side support. Install the screw and bolt. Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) for screw 12 N*m (122 kgf*cm, 9 ft.*lbf) for bolt 3. INSTALL FRONT BUMPER REINFORCEMENT (a) Install the reinforcement with the 6 nuts. 4. INSTALL FRONT BUMPER ENERGY ABSORBER 5. INSTALL FRONT BUMPER COVER (a) (b) Put protective tape under the front fender. Attach the 6 claws labeled A and 2 claws to install the bumper cover. B A B114870E01 Protector Clip A Protector Clip B (c) Install the 3 screws, 2 bolts, clip labeled A, 2 clips labeled B and 2 radiator protectors. Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) for screw 12 N*m (122 kgf*cm, 9 ft.*lbf) for bolt 6. INSTALL FRONT FENDER LINER LH (a) Install the fender liner with the 3 screws. Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) Clip B 7. INSTALL FRONT FENDER LINER RH (a) Install the fender liner with the 3 screws. Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) B114869E01
6 EXTERIOR REAR BUMPER BODY EXTERIOREAR BUMPER COMPONENTS REAR BUMPER SHIELD BRACK CENTER REAR NO. 1 BUMPER REINFORCEMENT REAR BUMPER ENERGY ABSORBER REAR BUMPER SIDE RAINER RH REAR BUMPER SIDE RAINER LH 6.0 (61, 53 in.*lbf) 6.0 (61, 53 in.*lbf) REAR BUMPER SIDE SEAL RH REAR BUMPER SIDE SEAL LH N*m (kgf*cm, ft.*lbf) : Specified torque REAR BUMPER COVER B114871E01
EXTERIOR REAR BUMPER 7 REMOVAL 1. REMOVE REAR BUMPER COVER (a) Remove the 4 screws. (b) Using a clip remover, remove the 4 clips. B084364E01 Protective Tape (c) Put protective tape under the quarter panel. (d) Using a screwdriver, detach the 14 claws and remove the bumper cover. The illustration only shows the LH side of the vehicle. The remaining claws are on the RH side. Tape the screwdriver tip before use. 2. REMOVE REAR BUMPER ENERGY ABSORBER 3. REMOVE REAR BUMPER SHIELD BRACK CENTER B084365E01 4. REMOVE REAR NO. 1 BUMPER REINFORCEMENT (a) Remove the 4 nuts and reinforcement. B084367E01 5. REMOVE REAR BUMPER SIDE RAINER LH (a) Remove the 3 screws. (b) Using a screwdriver, detach the 4 clips and remove the retainer. Tape the screwdriver tip before use. 6. REMOVE REAR BUMPER SIDE RAINER RH Use the same procedures described for the LH side. 7. REMOVE REAR BUMPER SIDE SEAL LH (a) Using a clip remover, remove the 3 clips and seal. 8. REMOVE REAR BUMPER SIDE SEAL RH (a) Using a clip remover, remove the 3 clips and seal. B084366E01
8 EXTERIOR REAR BUMPER INSTALLATION A bolt without a torque specification is shown in the standard bolt chart (see page SS-2). 1. INSTALL REAR BUMPER SIDE SEAL LH (a) Install the seal with the 3 clips. 2. INSTALL REAR BUMPER SIDE SEAL RH (a) Install the seal with the 3 clips. 3. INSTALL REAR BUMPER SIDE RAINER LH (a) (b) Attach the 4 clips to install the retainer. Install the 3 screws. Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) 4. INSTALL REAR BUMPER SIDE RAINER RH (a) Attach the 4 clips to install the retainer. (b) Install the 3 screws. Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) 5. INSTALL REAR NO. 1 BUMPER REINFORCEMENT (a) Install the reinforcement with the 4 nuts. 6. INSTALL REAR BUMPER SHIELD BRACK CENTER 7. INSTALL REAR BUMPER ENERGY ABSORBER B084367E01 8. INSTALL REAR BUMPER COVER (a) Put protective tape under the quarter panel. (b) Attach the 14 claws to install the bumper cover. The illustration only shows the LH side of the vehicle. The remaining claws are on the RH side. Protective Tape B084365E01
EXTERIOR REAR BUMPER 9 (c) Install the 4 screws and 4 clips. Torque: 6.0 N*m (61 kgf*cm, 53 in.*lbf) B084364E01
10 NAME PLATE BODY EXTERIOR COMPONENTS EXTERIOR NAME PLATE A A NO. 5 BACK DOOR NAME PLATE B114878E01
EXTERIOR NAME PLATE 11 REMOVAL NOTICE: Do not heat the vehicle body, emblem and name plate excessively. When removing the emblem and name plate, heat the vehicle body, emblem and name plate using a heat light. Standard heating temperature Item Vehicle Body Name Plate Temperature 40 to 60 C (104 to 140 F) 20 to 30 C (68 to 86 F) Protective Tape B114879E01 1. REMOVE NO. 5 BACK DOOR NAME PLATE (a) Put protective tape around the name plate. (b) Insert a piano wire between the vehicle body and name plate. (c) Tie objects that can serve as handles (for example, wooden blocks) to both wire ends. (d) Pull the piano wire and scrape off the double-sided tape that holds the name plate to the vehicle body. NOTICE: If reusing the name plate, take care not to damage the name plate. Be careful not to damage the vehicle body.
12 EXTERIOR NAME PLATE INSTALLATION NOTICE: Do not heat the vehicle body, emblem and name plate excessively. When installing the emblem and name plate, heat the vehicle body, emblem and name plate using a heat light. Standard heating temperature Item Vehicle Body Name Plate Temperature 40 to 60 C (104 to 140 F) 20 to 30 C (68 to 86 F) 1. INSTALL NO. 5 BACK DOOR NAME PLATE (a) Clean the vehicle body surface. (1) Using a heat light, heat the vehicle body surface. (2) Remove the double-sided tape from the vehicle body. (3) Wipe off any tape adhesive residue with cleaner. (b) If reusing the name plate: Clean the name plate. (1) Using a heat light, heat the name plate. (2) Remove the double-sided tape from the name plate. (3) Wipe off any tape adhesive residue with cleaner. (4) Apply new double-sided tape to the emblem. (c) Install the name plate. (1) Using a heat light, heat the vehicle body and name plate. (2) Remove the peeling paper from the face of the name plate. After removing the peeling paper, keep the exposed adhesive free from foreign matter. (3) Install the name plate. NOTICE: Install the name plate exactly according to the specifications below.
EXTERIOR NAME PLATE 13 Application Tape C A B B083385E01 Standard measurement Area A B C Measurement 8.7 mm (0.343 in.) 7.1 mm (0.280 in.) 24.7 mm (0.972 in.)
EXTERIOR FRONT DOOR BELT MOULDING FRONT DOOR BELT MOULDING BODY EXTERIOR COMPONENTS 13 FRONT DOOR BELT MOULDING LH OUTER REAR VIEW MIRROR ASSEMBLY LH FRONT DOOR LOWER FRAME BRACK GARNISH LH ASSIST GRIP COVER LH FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH FRONT ARMREST BASE PANEL UPPER LH B114875E01
14 EXTERIOR FRONT DOOR BELT MOULDING REMOVAL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. Before removing the moulding, fully open the door glass. 1. REMOVE FRONT DOOR LOWER FRAME BRACK GARNISH LH (See page ED-8) 2. REMOVE ASSIST GRIP COVER LH (See page ED-8) 3. REMOVE FRONT ARMREST BASE PANEL UPPER LH (See page ED-8) 4. REMOVE FRONT DOOR TRIM BOARD SUB- ASSEMBLY LH (See page ED-9) 5. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH (See page MI-8) 6. REMOVE FRONT DOOR BELT MOULDING LH (a) (b) Put protective tape under the moulding. Using a moulding remover, pry out the moulding as shown in the illustration. Tape the remover tip before use. NOTICE: Be careful when removing the moulding as there are clips attached to the front and rear ends of the moulding. Protective Tape B083384E01
EXTERIOR FRONT DOOR BELT MOULDING 15 INSTALLATION Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. INSTALL FRONT DOOR BELT MOULDING LH (a) Install the moulding as shown in the illustration. 2. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH (See page MI-10) 3. INSTALL FRONT DOOR TRIM BOARD SUB- ASSEMBLY LH (See page ED-19) 4. INSTALL FRONT ARMREST BASE PANEL UPPER LH (See page ED-20) 5. INSTALL ASSIST GRIP COVER LH (See page ED-21) 6. INSTALL FRONT DOOR LOWER FRAME BRACK GARNISH LH (See page ED-21) B117911
16 EXTERIOR FRONT PILLAR UPPER COVER FRONT PILLAR UPPER COVER BODY EXTERIOR COMPONENTS FRONT PILLAR COVER SUB-ASSEMBLY UPPER LH REMOVAL B114874E01 1. REMOVE FRONT PILLAR COVER SUB-ASSEMBLY UPPER LH (a) Using a moulding remover, detach the 2 clips and remove the pillar cover. B084150E01
EXTERIOR FRONT PILLAR UPPER COVER 17 INSTALLATION 1. INSTALL FRONT PILLAR COVER SUB-ASSEMBLY UPPER LH (a) Attach the 2 clips to install the pillar cover. B084150E01
18 SIDE MUDGUARD BODY EXTERIOR COMPONENTS EXTERIOR SIDE MUDGUARD NO. 1 SIDE MUDGUARD BRACK GROMM REAR WHEEL HOUSE PLATE FRONT LH CLIP GROMM GROMM CLIP CLIP RAINER RAINER SIDE MUDGUARD SUB-ASSEMBLY LH B114877E01
EXTERIOR SIDE MUDGUARD 19 REMOVAL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. REMOVE REAR WHEEL HOUSE PLATE FRONT LH (a) Remove the screw and wheel house plate. 2. REMOVE SIDE MUDGUARD SUB-ASSEMBLY LH (a) Remove the 2 screws, 6 retainers, 2 grommets and 6 clips labeled A. (b) Detach the 6 clips labeled B and remove the mudguard. B084138E01 Clip B Clip A Clip A Retainer Clip A Retainer B084152E01 3. REMOVE NO. 1 SIDE MUDGUARD BRACK (a) Remove the 2 screws. (b) Detach the claw and remove the bracket. B084153E01 INSTALLATION 1. INSTALL NO. 1 SIDE MUDGUARD BRACK (a) Attach the claw to install the bracket. (b) Install the 2 screws. 2. INSTALL SIDE MUDGUARD SUB-ASSEMBLY LH (a) Attach the 12 clips to install the mudguard. B084153E01
20 EXTERIOR SIDE MUDGUARD (b) Install the 6 retainers, 2 grommets and 2 screws. Retainer Retainer B084152E02 3. INSTALL REAR WHEEL HOUSE PLATE FRONT LH (a) Install the wheel house plate with the screw. B084138E01
EXTERIOR BACK DOOR OUTSIDE GARNISH BACK DOOR OUTSIDE GARNISH BODY EXTERIOR COMPONENTS 21 BACK DOOR GARNISH CENTER BACK DOOR SIDE GARNISH RH BACK DOOR SIDE GARNISH LH CENTER STOP LIGHT ASSEMBLY BACK DOOR GARNISH SUB-ASSEMBLY OUTSIDE B114876E01
22 EXTERIOR BACK DOOR OUTSIDE GARNISH REMOVAL 1. REMOVE BACK DOOR GARNISH CENTER (See page ED-24) 2. REMOVE BACK DOOR SIDE GARNISH LH (See page ED-24) 3. REMOVE BACK DOOR SIDE GARNISH RH (See page ED-24) 4. REMOVE CENTER STOP LIGHT ASSEMBLY (See page LI-28) 5. REMOVE BACK DOOR GARNISH SUB-ASSEMBLY OUTSIDE (a) (b) Remove the 4 nuts. Detach the clip and disconnect the connector. Then remove the garnish. B114885 (c) Remove the 2 screws and opener switch. B084141E01 INSTALLATION 1. INSTALL BACK DOOR GARNISH SUB-ASSEMBLY OUTSIDE (a) Install the opener switch with the 2 screws. (b) Connect the connector. (c) Attach the clip to install the garnish. B084141E01
EXTERIOR BACK DOOR OUTSIDE GARNISH 23 (d) Install the 4 nuts. B114885 2. INSTALL CENTER STOP LIGHT ASSEMBLY (See page LI-28) 3. INSTALL BACK DOOR SIDE GARNISH LH (See page ED-28) 4. INSTALL BACK DOOR SIDE GARNISH RH (See page ED-28) 5. INSTALL BACK DOOR GARNISH CENTER (See page ED-28)