Siebert 13 axle (3+3+3), 85 ton trailer West Coast Suspension KS-Stock Date: 1/17/14 Overall Trailer 1) Capacity 170,000# in 14 of main deck (without any deck inserts). GAWR & tire rating determine legal loads 2) Nominal dimensions 112-5 3/8 long 3) Width 10 wide 4) Weight For trailers other than standard specification, weight and dimensional drawing will be provided by plant after order is received and accepted 5) Warranty 5 year prorated frame warranty. 3 year prorated paint warranty. 1 year limited warranty on remainder of trailer Small Mechanical Gooseneck 1) Nominal dimensions 15 1 long 2) Kingpin height 50 3) Kingpin setting 15, 25 & 35 4) Swing clearance 108, 118 & 128 5) D-Rings 4 D-rings on top flange All specifications are reviewed at Kalyn Siebert prior to order acceptance Any revisions will be covered with a written change order The Kalyn Siebert standard one (1) year limited warranty will apply
Three Axle Jeep 1) Capacity 40 Ton capacity 2) Nominal dimensions 24 11 long 3) Width 10 wide 4) Neck ramps Sloped ramps for mechanical neck 5) Power Tower (Hatbox) 13 HP Honda power pack with 16 of cylinder travel in tower 6) 5 th wheel Fixed 7) Suspension Ridewell Model 240 Air Ride suspension, 60 axle spacing, lift chains. Air Weigh air 8) Air Controls Automatic/Manual ride height control system. Manual raise and lower valve with liquid filled air pressure gauge 9) Axles Three OEM axles, 5 round, tapered spindles, 25,000 lb capacity, 95 track 10) Hubs 10 stud, hub piloted, long studs, steel hub, Stemco oil seals 11) Drums Cast drum 12) Seals Oil 13) Brakes 16½ X 7. No parking brakes 14) ABS None 15) Slack adjusters Automatic slack adjusters, 28 spline 16) Wheels Aluminum wheels, polished outside, mill finish inside 17) Tires OEM, 295/75R22.5, 16PR radial tires 18) Mud flaps Black Anti-Spray with Kalyn Siebert Logo 19) D-Rings 4 D-Rings on jeep for picking up to stack 20) Finishing 21) Lights & electrical LED Shot blasted prior to paint. Epoxy primer and Black polyurethane paint. Air, electrical 3
Large Mechanical Goosenecks 1) Nominal dimensions 25 6 ¾ long 2) Kingpin height 62 3) Kingpin setting 15 4) Swing clearance 250 5) D-Rings 4 D-rings on top flange Main deck and rear deck section 1) Capacity 170,000# in 14 of main deck (without any deck inserts) GAWR & tire rating determine legal loads 2) Nominal dimensions 10 wide X 53 length 3) Deck 30 level deck with detachable rear section for installation of deck inserts. Horizontal pin joint design for maximum shimming to raise and lower rear deck height 4) Insert 10 deck insert with 4 D-rings 5) Deck height 26 deck height with 7 ground clearance at rated capacity 6) Cross members Formed channel cross members on 24 centers. 80,000 psi yield strength minimum 7) Decking 2 ¼ Apitong floor outer only. Center is open to store outrigger boards 8) Outriggers Full set of heavy cast removable outriggers with storage in neck 9) Tool Tray Expanded metal 6 10) Tie downs Square holes in deck, chain slots in bolsters, 16 D-rings on lower deck (one being all the way to front), 4 D-rings to the inside of the center beams (angled towards the center of the deck) at front and rear of deck 11) Flag Holders Two pair, front and rear 12) Suspension Ridewell Model 240 Air Ride suspension, 60 axle spacing, lift chains. Air Weigh air 13) Air Controls Automatic/Manual ride height control system. Manual regulator can be set based on load and locked to a specific pressure. Manual dump valve standard 14) Axles Three OEM axles, 5 round, 3/4 wall, tapered spindles, 25,000 lb capacity, 95 track 4
15) Hubs 10 stud, hub piloted, long studs, steel hub, Stemco oil seals 16) Drums Cast drum 17) Seals Oil 18) Brakes 16½ X 7. Parking brakes on three axles. Parking brake release valve standard 19) ABS None 20) Slack adjusters Automatic slack adjusters, 28-spline 21) Wheels Aluminum wheels, polished outside, mill finish inside 22) Tires OEM, 295/75R22.5, 16PR radial tires 24) Mud flaps Black Anti-Spray with Kalyn Siebert Logo 25) Lights & electrical LED; Amber strobe light in bumper 26) Finishing 1) Capacity 60,000# tire load at ground Shot blasted prior to paint. Epoxy primer and Black polyurethane paint. Air, electrical Three Axle Booster 2) Width 10 wide 3) Booster spread 16 1 booster spread 4) Steering Towable, rear articulating follow steering 5) Booster pin 5 steel shaft 7.5 steel collars with greaseable brass bushing inserts 6) Lock pin Dual air lock pins to lock booster straight while backing 7) Wide load sign Wide load sign on rear booster 8) Steering Hydraulic bump steering with 20HP Honda power package mounted on booster 9) Tie downs 4 D- Rings for picking up to stack 10) Flag holders One pair, at rear 11) Suspension Ridewell Model 240 Air Ride suspension, 60 axle spacing, lift chains. Air Weigh air 12) Air Controls Automatic/Manual ride height control system. Manual raise and lower valve with liquid filled air pressure gauge 5
13) Axles Three OEM axles, 5 round, tapered spindles, 25,000 lb capacity, 95 track 14) Hubs 10 stud, hub piloted, long studs, steel hub, Stemco oil seals 15) Drums Cast drum 16) Seals Oil 17) Brakes 16½ X 7. No parking brakes standard 18) ABS None 19) Slack adjusters Automatic slack adjusters, 28-spline 20) Wheels Aluminum wheels, polished outside, mill finish inside 21) Tires OEM, 295/75R22.5, 16PR radial tires 22) Mud flaps Black Anti-Spray with Kalyn Siebert Logo 23) Finishing Shot blasted prior to paint. Epoxy primer and Black polyurethane paint. Air, electrical 24) Lights & electrical LED; Amber strobe light in bumper 6