Chopper/Wet-out Systems Low-Emission Resin Systems for the Composites Industry
GlasCraft Chopper/Wet-out Systems Outstanding performance for resin applications Designed to accurately meter and chop fiberglass into a resin spray to provide structural strength to the end product, GlasCraft Chopper/ Wet-out Dispense Systems are engineered to deliver reliable performance. Built with fewer wear items, GlasCraft equipment consumes fewer replacement parts. With reduced service expenses and less revenue lost due to downtime, GlasCraft s Chopper Systems are highly economical to own and operate. GlasCraft Chopper/Wet-out Systems: Dispense polyester resin and vinyl ester chemicals Allow for infinite adjustment of the catalyst ratio no tools required Offer reliable, highly accurate ratio control Provide high-efficiency performance at low spraying pressures Available in internal and external mix configurations Typical applications: Marine and watercraft Pool and spa Bathware Transportation Corrosion prevention Dual Upper Seals on Catalyst Pump Dual seal prevents leakage any weapage past the primary seal is returned to the catalyst reservoir, not on the floor Secondary shaft seal Primary shaft seal Long-life Design Triple-lip spring-loaded seals and hardened cylinders, seats and valves provide long wear life GlasCraft Chopper/Wet-out Dispense System 2
Adjustable-Ratio Catalyst Pump Fluid Pressure Gauge Easy-to-read gauge for verification of catalyst fluid flow Manual Relief Valve Easy startup, shut down and maintenance Heavy Duty Rugged stainless steel construction Precision Air Pilot Valve Allows fast pneumatic changeover without any parts to wear out Easy, no-tool quick-change catalyst adjustment Ensures proper catalyst percentage and optimal results Operates at any desired catalyst percentage within operating range 0.5% to 3.5% for 5:1 system 0.5% to 3.5% for 11:1 system 0.5% to 2.9% for 17:1 system 0.8% to 5.6% for 20:1 system Resin Pump Reliable, low-maintenance reciprocating piston pump for moving polyester resin Piston pump works well with fillers Standard pump offers 11:1 ratio Develops up to 1300 psi (89 bar, 8.9 MPa) Delivers up to 2.5 gpm (9.5 lpm) Surge Bottle Accumulator Ensures consistent pressure for ideal spray pattern Quick Change Seal Design Tool-less quick disconnect allows for easy top seal maintenance Lower end is easily removed to service lower seals on pump Four-inch Stroke Uses fewer cycles, which means less wear and increased uptime Optional resin pumps: 5:1 Pump For low-pressure applications Develops up to 500 psi (34 bar, 3.4 MPa) Delivers up to 2.5 gpm (9.5 lpm) HVRP 17:1 Pump Designed for high volume resin or chopper applications Ideal for high volume production shops Develops up to 1700 psi (117 bar, 11.7 MPa) Delivers up to 4.1 gpm (15.5 lpm) Low VOC 20:1 For high-viscosity materials Develops up to 2000 psi (138 bar, 13.8 MPa) Delivers up to 1.6 gpm (6.0 lpm) 3
Air Assist Containment Advanced technology to control and contain your spray pattern When you buy a drum of resin, you pay for every drop of material. It makes good economic sense to put as many of those drops as possible on the mold. GlasCraft s exclusive Air Assist Containment (AAC) wraps the spray pattern in a containment shield of air preventing atomized droplets from escaping the spray pattern. Droplets that escape and end up on the floor, wall or employee s clothing are a waste of money. AAC creates a spray pattern where the droplets travel to the mold at very low pressure. The low speed or particle velocity creates very little turbulence or disturbance in the liquid when the droplet makes contact with the mold. Competitive spray guns with higher particle velocity create a great deal of turbulence when the droplets impact the mold. Turbulence creates air entrapment which results in porosity. AAC spraying dramatically reduces the chances of air entrapment and porosity. AAC improves your profit picture All GlasCraft external mix spray guns feature the patented AAC technology The AAC screw-on option is available for all internal material guns Reduces material waste which results in more molds per drum of material Precise catalyst delivery and reduced particle velocity assure the highest quality finish Less overspray means a healthier work area for employees Catalyst Air Assist Containment After introduction of catalyst Resin Low pressure air is delivered into the catalyst stream. Resin Catalyst Air Assist Contact Before introduction of catalyst Low pressure catalyst is delivered thoroughly into the resin pattern. GlasCraft s catalyst delivery process assures a complete mix with the resin. The patented AAC is introduced to the spray pattern after the catalyst assuring a complete mix, reducing overspray and providing the highest transfer efficiency. 4
GlasCraft Chopper Spray Guns Uniform spray pattern GlasCraft s chopper external guns feature the patented AAC feature to produce the most uniform and consistent low-emission spray pattern with stabilizing air streams. GlasCraft Formula Guns Air-actuated trigger provides immediate response, virtually eliminating hot and cold spots No-needle design eliminates needle adjustments Special hardened valves are engineered for today s low VOC formulations Fluid control occurs via air-operated piston that opens and closes internal ball valves Easy access to valve packings for quick maintenance and increased uptime Feature AAC technology for uniform spray pattern with minimal overspray What s the difference between external and internal mix guns? External mix guns: Ideal for low-emission resin applications Chemical is mixed outside the gun Operators can see the catalyst being added to the mix Does not require a solvent flush Formula Internal Mix Gun with Chopper Precision check valves automatically balance fluid pressures Extended mix area results in the best mix Formula X External Mix Gun with Chopper Unique catalyst delivery assures complete integration to the spray pattern Easy visual verification of catalyst flow No solvent needed to flush Internal mix guns: Ideal for chopper and wet-out systems Ensures the best possible mix Because you do not need to pre-atomize the catalyst, there is less forward velocity, which results in less overspray Requires a solvent flush for maintenance GlasCraft INDy Spray Guns Volume control assures the highest quality finish with minimal porosity Simple material valve and seat design is easy to maintain, resulting in increased uptime Features AAC for excellent pattern control and less wasted material Ergonomic, lightweight design reduces operator fatigue INDy Internal Mix Gun with Chopper Fully adjustable pattern control and precision check valves to automatically balance fluid pressures Extended mix area results in the best mix INDy X External Mix Gun with Chopper Unique catalyst delivery assures complete integration to the spray pattern No solvent needed to flush 5
Solutions for the Composites Industry GlasCraft Fiberglass Cutters Exceptionally quiet, GlasCraft s unique cutter maintains 100 percent torque to the air motor for unchallenged high and low fiber output, and provides the flexibility to pull the fiber from long distances. All GlasCraft choppers feature superior airflow, which results in a low operating temperature and the best performance with soft glass. B-410 Cutter Unique air flow design results in cooler operating temperature Several snout options to efficiently dispense glass in both large and small parts Adjustable throttle for output control Efficiently pulls one or two strands of glass B-510 Cutter Wide surface area idler bearing allows for even glass disbursement and minimizes glass hang up Blower adjustment helps control operating temperature and flow of the glass New design cutter wheel for quick and safe blade change Automatically keeps proper tension between the blade and wheel for longer tire life and cooler operating temperature Fully adjustable snout to easily set the most efficient angle into the resin pattern Adjustable throttle for output control Efficiently pulls up to three strands of glass 6
Technical Specifications Air requirement INDy/Formula 5:1 INDy/Formula 11:1 INDy Formula HVRP 17:1 INDy/Formula 20:1 15 cfm @ 100 psi @ max pump output (425 lpm @ 6.8 bar @ max pump output) 35 cfm @ 100 psi max output (991 lpm @ 6.8 bar @ max pump output) 80 cfm @ max output (2265 lpm @ 6.8 bar @ max pump output) 35 cfm @ 100 psi max output (991 lpm @ 6.8 bar @ max pump output) Material pump capacity* 2.5 gpm (9.5 lpm) 2.5 gpm (9.5 lpm) 4.1 gpm (15.5 lpm) 1.6 gpm (6.0 lpm) Material pump output.050 gal per cycle; 20 cycles = 1 gal; 5 cycles = 1 liter.050 gal per cycle; 20 cycles = 1 gal; 5 cycles = 1 liter.082 gal per cycle; 12 cycles = 1 gal; 3 cycles = 1 liter.032 gal per cycle; 31 cycles = 1 gal; 8 cycles = 1 liter Catalyst slave pump range 0.5% to 3.5% 0.5% to 3.5% 0.5% to 2.9% 0.8% to 5.6% * Material pump capacity is based on 50 cycles per minute. Higher cycle rates can be achieved depending on material viscosity, material temperature and volume of air. All pump outputs are measured at the pump outlet using a low viscosity test media. Accessories Spray Tips Impingement Style Airless Style Part Number Orifice Part Number Orifice Part Number Orifice Part Number Orifice Part Number Orifice Part Number Orifice 23005-C4 0.040 23005-G9 0.090 23005-P4 0.040 LPA2-147-1525 0.015 LPA2-147-2640 0.026 LPA2-147-4350 0.043 23005-C5 0.050 23005-J4 0.040 23005-TC6 0.060 LPA2-147-1540 0.015 LPA2-147-2650 0.026 LPA2-147-4365 0.043 23005-C6 0.060 23005-J5 0.050 23005-TC7 0.070 LPA2-147-1825 0.018 LPA2-147-2665 0.026 LPA2-147-5225 0.052 23005-C7 0.070 23005-J6 0.060 23005-TC8 0.080 LPA2-147-1840 0.018 LPA2-147-3125 0.031 LPA2-147-5240 0.052 23005-C8 0.080 23005-J7 0.070 23005-TE7 0.070 LPA2-147-1850 0.018 LPA2-147-3140 0.031 LPA2-147-5250 0.052 23005-C9 0.090 23005-J8 0.080 23005-TG7 0.070 LPA2-147-2125 0.021 LPA2-147-3150 0.031 LPA2-147-5265 0.052 23005-E4 0.040 23005-J9 0.090 23047-J1 0.012 LPA2-147-2140 0.021 LPA2-147-3625 0.036 LPA2-147-6225 0.062 23005-E5 0.050 23005-K3 0.040 23047-J2 0.014 LPA2-147-2150 0.021 LPA2-147-3640 0.036 LPA2-147-6240 0.062 23005-E6 0.060 23005-K4 0.040 23047-J3 0.022 LPA2-147-2165 0.021 LPA2-147-3650 0.036 LPA2-147-6250 0.062 23005-E7 0.070 23005-K5 0.050 23047-M1 0.012 LPA2-147-2325 0.023 LPA2-147-3840 0.038 LPA2-147-6265 0.062 23005-E8 0.080 23005-K6 0.060 23047-M2 0.014 LPA2-147-2340 0.023 LPA2-147-3850 0.038 LPA2-147-7240 0.072 23005-E9 0.090 23005-K7 0.070 23047-M3 0.022 LPA2-147-2350 0.023 LPA2-147-4325 0.043 LPA2-147-7250 0.072 23005-G4 0.040 23005-K8 0.080 23047-P1 0.012 LPA2-147-2365 0.023 LPA2-147-4340 0.043 LPA2-147-7840 0.078 23005-G5 0.050 23005-K9 0.090 23047-P2 0.014 23005-G6 0.060 23005-M4 0.040 23047-P3 0.022 23005-G7 0.070 23005-M5 0.050 23005-G8 0.080 23005-M6 0.060 PFR Option - Add on option for Internal Mix INDy and Formula Guns GCC238 Pressure Fed Roller Kit, 1.5 ft (0.45m) GCC239 Pressure Fed Roller Kit, 3 ft (0.91m) GCC240 Pressure Fed Roller Kit, 6 ft (1.83m) Not included in the kits above, but required, is a roller cover. Choose a roller cover from below. 20335-01 Roller Cover, 9 in X 1/2 in Nap 20335-02 Roller Cover, 9 in X 3/4 in Nap Formula/INDy Screw on AAC Gun Head Kit 23570-00 Internal Mix Gel - Screw On AAC Gun Head Kit NOTE: P/N 23570 requires a regulator assembly which is not included in kit. The following must be ordered for a complete regulator assembly. Regulator Assembly 3165 Ball Valve 4342-04 Elbow Fitting 7884-07 Elbow Fitting 8115-03 Nipple Fitting 9704-53 Black Aac Tubing Order length should be fluid hose length plus 3 feet 18199-02 Regulator 18318-02 Gauge 20182-00 AAC Decal Small Diameter Airless/NON Atomized Material Tip Conversion Parts 20333-00 Gasket 22274-00 Tip Spacer 23002-00 Retaining Nut LPA2-147-XXXX Spray Tip 23047-Xx Spray Tip 23760-00 Gun Front Housing For Formula Gun Only 23502-00 Gun Front Housing For INDy Gun Only Formula High/High Filled Resin Mixer conversion Parts 20310-90 3/8 in Mixing Element 23760-01 3/8 in Front Mixer Housing INDy/Formula RTM Adapter 21652-00 Injection Nozzle 21662-00 Injection Wand 23003-00 Spray Tip Spacer 23049-00 RTM Adapter FTG INDy/Formula Casting Adapter 20624-00 Jacket Nozzle 20625-00 Mix Nozzle 23003-00 Spray Tip Spacer 23049-00 RTM Adapter FTG Repair Kits Formula Gun 23792-00 Gun Air Kit 23793-00 Gun Seal Kit 23732-00 Gun Fluid Valve Kit INDy Gun 23530-00 Complete Rebuild Kit 23538-00 Maintenance Kit Catalyst Pump LPA-190-RK LPA-190-SK Complete Rebuild Kit Seal Kit 13:1 Air Motor (3.25 in) 20840-00 Complete Service Kit 20104-00 Stroke Signal Repair Kit 20841-00 Cylinder Repair Kit 20842-00 Reciprocating Valve Kit 20843-00 Valve Air Kit 11:1 and 20:1 Air Motor (5 in) 20101-00 Complete Service Kit 20107-00 Pilot Valve Kit 20106-00 Main Valve Kit 20105-00 Gasket Kit 20104-00 Stroke Signal Repair Kit 20103-00 Rod Seal Kit 20102-00 Piston Rod Seal Kit 17:1 Air Motor (6 in) 21380-01 Complete Service Kit 20104-00 Stroke Signal Repair Kit 21381-00 Bushing Rod 21382-01 Air Unit 22343-00 Valve Repair Kit 22344-00 Pilot Valve Kit Fluid Section 21570-00 5:1/11:1 Repair Kit 19019-01 13:1 Repair Kit 21799-00 17:1 Repair Kit 21277-00 20:1 Repair Kit 7
ABOUT GRACO Founded in 1926, Graco is a world leader in fluid handling systems and components. Graco products move, measure, control, dispense and apply a wide range of fluids and viscous materials used in vehicle lubrication, commercial and industrial settings. The company s success is based on its unwavering commitment to technical excellence, world-class manufacturing and unparalleled customer service. Working closely with qualified distributors, Graco offers systems, products and technology that set the quality standard in a wide range of fluid handling solutions. Graco provides equipment for spray finishing, protective coating, paint circulation, lubrication, and dispensing sealants and adhesives, along with power application equipment for the contractor industry. Graco s ongoing investment in fluid management and control will continue to provide innovative solutions to a diverse global market. GRACO LOCATIONS MAILING ADDRESS P.O. Box 1441 Minneapolis, MN 55440-1441 Tel: 612-623-6000 Fax: 612-623-6777 AMERICAS MINNESOTA Worldwide Headquarters Graco Inc. 88-11th Avenue N.E. Minneapolis, MN 55413 EUROPE BELGIUM European Headquarters Graco N.V. Industrieterrein-Oude Bunders Slakweidestraat 31 3630 Maasmechelen, Belgium Tel: 32 89 770 700 Fax: 32 89 770 777 ASIA PACIFIC AUSTRALIA Graco Australia Pty. Ltd Suite 17, 2 Enterprise Drive Bundoora, 3083 Victoria, Australia Tel: 61 3 946 78558 Fax: 61 3 946 78559 CHINA Graco Hong Kong Ltd. Shanghai Representative Office Room 118 1st Floor No.2 Xin Yuan Building No.509 Cao Bao Road Shanghai, P.R. China 200233 Tel: 86 21 649 50088 Fax: 86 21 649 50077 INDIA Graco Hong Kong Ltd. India Liaison Office Room 103, Level 4, Augusta Point Golf Course Road Gurgaon, Haryana, India 122001 Tel: +91 124 435 4208 Fax: +91 124 435 4001 JAPAN Graco K.K. 1-27-12 Hayabuchi Tsuzuki-ku Yokohama City, Japan 2240025 Tel: 81 45 593 7300 Fax: 81 45 593 7301 KOREA Graco Korea Inc. Choheung Bank Building 4th Floor #1599 Gwanyang-Dong, Dongan-Ku, Anyang-Si, Gyunggi-Do, Korea 431-060 Tel: 82 31 476 9400 Fax: 82 31 476 9801 SALES/ DISTRIBUTION/ SERVICE Call today for product information or to request a demonstration. 800-746-1334 or visit us at www.graco.com. Graco Inc. is registered to I.S. EN ISO 9001 Graco Ohio 800-746-1334 Fax 330-966-3006 2008 Graco Inc. 340041 Rev. A 12/08 All written and visual data contained in this document are based on the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. All other brand names or marks are used for identification purposes and are trademarks of their respective owners.