SHELL AND TUBE HEAT EXCHANCER PERFORMANCE SPECIFICATION SHEET Service of Unit Aftercooler Item No 02 Case Minumum Model G - 17-5.00-120 - 1P TEMA Type BEP Connected In 1 Parallel 1 Series Surf/Unit (Gross/Eff) 319 / 310 ft² Shells/Unit 1 Surf/Shell (Gross/Eff) 319 / 310 ft² PERFORMANCE OF ONE UNIT Fluid Allocation Shell Side Tube Side Fluid Name WATER AIR Fluid Quality, Total lb/hr 32,881 2,635 Vapor (In/Out) 2,635 2,635 Liquid Steam Water 32,881 32,881 Noncondensable 2,635 2,635 Temperature (In/Out) F 54.00 56.17 170.00 56.95 Specific Density lbm/ft3 62.41 62.39 Viscosity, Liquid cp 1.208 1.173 Molecular Weight, Vapor 28.96 28.96 Molecular Weight, Noncondensable Specific Heat Btu/lb-F 1.00 1.00 Btu/hr-ft-F 0.36 0.36 Latent Heat Btu/lb Inlet Pressure psia 156.10 Velocity ft/sec 3.67 3.59 Pressure Drop, Allow/Calc psi 9.00 0.96 0.70 0.01 Fouling Resistance (min) 0.0010 0.0005 Heat Exchanged 71,483 Btu/hr MTD (Corrected) 30.37 F Transfer Rate, Service 7.66 Clean 7.76 Btu/hr-ft²-F CONSTRUCTION OF ONE SHELL Sketch (Bundle/Nozzle Orientation) Shell Side Tube Side
Design/Test Pressure psig 150 / PER CODE 200 / PER CODE Design Temperature F 200 / 51 200 / 51 No Passes per Shell 1 1 Corrosion Allowance inch 0.0625 0.0625 Connections In inch 1 @ 2-150# RFSO 1 @ 10-150# RFSO Size & Out inch 1 @ 2-150# RFSO 1 @ 10-150# RFSO Rating Intermediate 1 @ 0.75-3000# NPT 1 @ 0.75-3000# NPT Tubes No. 195 OD 0.625 in. Thk(Avg) 0.049 in. Length: 120 in Pitch: 0.7813 in. Layout: 45 degrees Tube Type PLAIN Material: 304 Stainless stee Shell CARBON STEEL ID 17.25 OD inch Shell Cover Channel or Bonnet 304 STAINLESS STEEL Channel Cover 304 STAINLESS STEEL Tubesheet-Stationary 304 STAINLESS STEEL Tubesheet-Floating 304 STAINLESS STEEL Floating Head Cover 304 STAINLESS STEEL Impringement Protection YES Baffles-Cross SA-516 Type SEGMENTAL %Cut (Diam) 30 Spacing(c/c) 4.72 Inlet 11.10 inch Baffles-Long Seal Type Supports-Tube U-Bend Type Bypass Seal Arrangement Tube-Tubesheet Joint GROOVED, ROLLED, AND SEAL WELDED Expansion Joint NO Type Rho-V2-Inlet Nozzle Bundle Entrance Bundle Exit Gaskets-Shell Side NONASBESTOS Tube Side NONASBESTOS -Floating Head NONASBESTOS Code Requirements ASME SECTION VIII DIVISION 1 TEMA Class C Weight/Shell Operating Bundle lb Remarks Industrial Heat Exchangers 5701 S. Eastern Ave. Suite 300 Los Angeles, CA 90040 SHELL AND TUBE HEAT EXCHANCER PERFORMANCE SPECIFICATION SHEET Service of Unit Aftercooler Item No 02 Case Nominal
Model G - 17-5.00-120 - 1P TEMA Type BEP Connected In 1 Parallel 1 Series Surf/Unit (Gross/Eff) 319 / 310 ft² Shells/Unit 1 Surf/Shell (Gross/Eff) 319 / 310 ft² PERFORMANCE OF ONE UNIT Fluid Allocation Shell Side Tube Side Fluid Name WATER AIR Fluid Quality, Total lb/hr 32,881 6,740 Vapor (In/Out) 6,740 2,635 Liquid Steam Water 32,881 32,881 Noncondensable 6,740 6,740 Temperature (In/Out) F 54.00 59.40 170.00 59.97 Specific Density lbm/ft3 62.41 62.36 Viscosity, Liquid cp 1.208 1.122 Molecular Weight, Vapor 28.96 28.96 Molecular Weight, Noncondensable Specific Heat Btu/lb-F 1.00 1.00 Btu/hr-ft-F 0.36 0.36 Latent Heat Btu/lb Inlet Pressure psia 156.10 Velocity ft/sec 3.67 9.23 Pressure Drop, Allow/Calc psi 9.00 0.96 0.70 0.05 Fouling Resistance (min) 0.0010 0.0005 Heat Exchanged 177,980 Btu/hr MTD (Corrected) 35.85 F Transfer Rate, Service 16.18 Clean 16.61 Btu/hr-ft²-F CONSTRUCTION OF ONE SHELL Sketch (Bundle/Nozzle Orientation) Shell Side Tube Side Design/Test Pressure psig 150 / PER CODE 200 / PER CODE Design Temperature F 200 / 51 200 / 51
No Passes per Shell 1 1 Corrosion Allowance inch 0.0625 0.0625 Connections In inch 1 @ 2-150# RFSO 1 @ 10-150# RFSO Size & Out inch 1 @ 2-150# RFSO 1 @ 10-150# RFSO Rating Intermediate 1 @ 0.75-3000# NPT 1 @ 0.75-3000# NPT Tubes No. 195 OD 0.625 in. Thk(Avg) 0.049 in. Length: 120 in Pitch: 0.7813 in. Layout: 45 degrees Tube Type PLAIN Material: 304 Stainless stee Shell CARBON STEEL ID 17.25 OD inch Shell Cover Channel or Bonnet 304 STAINLESS STEEL Channel Cover 304 STAINLESS STEEL Tubesheet-Stationary 304 STAINLESS STEEL Tubesheet-Floating 304 STAINLESS STEEL Floating Head Cover 304 STAINLESS STEEL Impringement Protection YES Baffles-Cross SA-516 Type SEGMENTAL %Cut (Diam) 30 Spacing(c/c) 4.72 Inlet 11.10 inch Baffles-Long Seal Type Supports-Tube U-Bend Type Bypass Seal Arrangement Tube-Tubesheet Joint GROOVED, ROLLED, AND SEAL WELDED Expansion Joint NO Type Rho-V2-Inlet Nozzle Bundle Entrance Bundle Exit Gaskets-Shell Side NONASBESTOS Tube Side NONASBESTOS -Floating Head NONASBESTOS Code Requirements ASME SECTION VIII DIVISION 1 TEMA Class C Weight/Shell Operating Bundle lb Remarks Industrial Heat Exchangers 5701 S. Eastern Ave. Suite 300 Los Angeles, CA 90040 SHELL AND TUBE HEAT EXCHANCER PERFORMANCE SPECIFICATION SHEET Service of Unit Aftercooler Item No 02 Case Maximum Model G - 17-5.00-120 - 1P TEMA Type BEP Connected In 1 Parallel 1 Series Surf/Unit (Gross/Eff) 319 / 310 ft² Shells/Unit 1 Surf/Shell (Gross/Eff) 319 / 310 ft²
PERFORMANCE OF ONE UNIT Fluid Allocation Shell Side Tube Side Fluid Name WATER AIR Fluid Quality, Total lb/hr 32,881 21,563 Vapor (In/Out) 21,563 2,635 Liquid Steam Water 32,881 32,881 Noncondensable 21,563 21,563 Temperature (In/Out) F 54.00 69.78 170.00 69.53 Specific Density lbm/ft3 62.41 62.25 Viscosity, Liquid cp 1.208 0.981 Molecular Weight, Vapor 28.96 28.96 Molecular Weight, Noncondensable Specific Heat Btu/lb-F 1.00 1.00 Btu/hr-ft-F 0.36 0.36 Latent Heat Btu/lb Inlet Pressure psia 156.10 Velocity ft/sec 3.67 29.78 Pressure Drop, Allow/Calc psi 9.00 0.95 0.70 0.41 Fouling Resistance (min) 0.0010 0.0005 Heat Exchanged 520,210 Btu/hr MTD (Corrected) 45.28 F Transfer Rate, Service 36.93 Clean 39.24 Btu/hr-ft²-F CONSTRUCTION OF ONE SHELL Sketch (Bundle/Nozzle Orientation) Shell Side Tube Side Design/Test Pressure psig 150 / PER CODE 200 / PER CODE Design Temperature F 200 / 51 200 / 51 No Passes per Shell 1 1 Corrosion Allowance inch 0.0625 0.0625
Connections In inch 1 @ 2-150# RFSO 1 @ 10-150# RFSO Size & Out inch 1 @ 2-150# RFSO 1 @ 10-150# RFSO Rating Intermediate 1 @ 0.75-3000# NPT 1 @ 0.75-3000# NPT Tubes No. 195 OD 0.625 in. Thk(Avg) 0.049 in. Length: 120 in Pitch: 0.7813 in. Layout: 45 degrees Tube Type PLAIN Material: 304 Stainless stee Shell CARBON STEEL ID 17.25 OD inch Shell Cover Channel or Bonnet 304 STAINLESS STEEL Channel Cover 304 STAINLESS STEEL Tubesheet-Stationary 304 STAINLESS STEEL Tubesheet-Floating 304 STAINLESS STEEL Floating Head Cover 304 STAINLESS STEEL Impringement Protection YES Baffles-Cross SA-516 Type SEGMENTAL %Cut (Diam) 30 Spacing(c/c) 4.72 Inlet 11.10 inch Baffles-Long Seal Type Supports-Tube U-Bend Type Bypass Seal Arrangement Tube-Tubesheet Joint GROOVED, ROLLED, AND SEAL WELDED Expansion Joint NO Type Rho-V2-Inlet Nozzle Bundle Entrance Bundle Exit Gaskets-Shell Side NONASBESTOS Tube Side NONASBESTOS -Floating Head NONASBESTOS Code Requirements ASME SECTION VIII DIVISION 1 TEMA Class C Weight/Shell Operating Bundle lb Remarks