Alarms & Remote Start Automotive Data Solutions Inc. NI INSTALL UIDE OL-BLADE-AL(DL-NI-EN AVAILABLE FOR : OL-BLADE-AL Rev. Date: August 0, Doc. No.: ##0## U.S. PENT NO.,,0 The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc.! NOTIE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation uide carefully before beginning any work.
INSTALL UIDE U.S. Patent No.,,0 Page of 0 Doc. No.: ##0## INSTALL TYPE SELETI Door lock Door Unlock DISarM oem alarm a/m alarm ctrl from oem remotes a/m rs ctrl from oem remotes& trunk/hatch release Door StatUS output HooD StatUS output trunk StatUS output PeDal StatUS output tachometer output e- output M 0- Q0 - Q0L - QX - QX0 - ube 0- Juke - Juke MT - Quest - PoWer SlIDIn Door (r SecUre takeover 0- PoWer SlIDIn Door (l Data IMMoBIlIZer BYPaSS - M PoWer liftate Year M Hybrid InStall type MoDel nissan InfInItI Make features Quest w/ electric sliding door - Sentra - Versa Sedan - Versa Note - Available only for AL-k, AL-k & BLADE-AL k with compatible RS. Telematics Data ateway not available on BLADE-AL k. This feature is disabled by default, it must be enabled during programming. Available only when a factory hood switch is present. Available only when ignition is in the position. Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of Doc. No.: ##0## 0 PoSItIon PolarItY MoDUle location component locator - type Q0 0- M name 0- InfInItI M - DeScrIPtIon M Hybrid Year MoDel Make TYPE - WIRE ROSS REFERENE HART - OF M M M0 Immobilizer behind button M0 0 reen Immobilizer behind button M0 pin 0 E0 switch M M pin BM left of steering wheel M0 BM left of steering wheel M0 BM left of steering wheel M M M0 Immobilizer behind button M0 0 reen Immobilizer behind button M0 pin 0 E0 switch M M pin BM left of steering wheel M0 BM left of steering wheel M0 BM left of steering wheel M M M0 Immobilizer behind button M0 0 reen Immobilizer behind button M0 pin 0 E0 switch M M pin BM M0 BM M0 BM M M M0 Immobilizer behind button M0 0 reen Immobilizer behind button M0 pin 0 E0 switch M M pin BM left of steering wheel M0 BM left of steering wheel M0 BM left of steering wheel Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of Doc. No.: ##0## 0 PoSItIon PolarItY MoDUle location component locator 0- type ube - nissan QX0 - name QX - DeScrIPtIon InfInItI Q0L Year MoDel Make TYPE - WIRE ROSS REFERENE HART - OF M M M0 Immobilizer behind button M0 0 reen Immobilizer behind button M0 pin 0 E0 switch M M pin BM left of steering wheel M0 BM left of steering wheel M0 BM left of steering wheel M Immobilizer behind button M 0 /Red Immobilizer behind button M0 pin 0 Lt E Red switch ray M pin ray/red BM behind cluster BM behind cluster BM behind cluster M Immobilizer behind button M 0 /Red Immobilizer behind button M0 pin 0 Lt E Red switch ray M pin ray/red BM behind cluster BM behind cluster BM behind cluster M / Immobilizer behind button M 0 Immobilizer behind button M0 pin /Orange E switch Orange M pin /Yellow BM driver kick panel / BM driver kick panel 0 /Red BM driver kick panel Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of Doc. No.: ##0## 0 PoSItIon PolarItY MoDUle location component locator - type Versa Sedan - Quest name - nissan Quest - DeScrIPtIon Juke Year MoDel Make TYPE - WIRE ROSS REFERENE HART - OF Immobilizer behind button 0 Immobilizer behind button M0 pin E switch B0 pin Lt BM near A-pillar driver side Red BM near A-pillar driver side 0 BM near A-pillar driver side M Red Immobilizer behind button M 0 Immobilizer behind button M0 pin 0 E switch reen M pin reen BM behind cluster M Yellow BM behind cluster M 0 BM behind cluster M ray Immobilizer behind button M 0 Immobilizer behind button M0 pin 0 E switch reen M pin reen BM behind cluster M ray BM behind cluster M 0 BM behind cluster Immobilizer behind button 0 Immobilizer behind button M0 pin E switch Orange B0 pin Lt BM near A-pillar driver side ray BM near A-pillar driver side 0 BM near A-pillar driver side Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of 0 Doc. No.: ##0## TYPE - WIRIN DIARAM OBDII NETOR ED UNDER DRIVER SIDE DASH 0 TI NI I (+ NH A NL A BRAE SWITH E A BR (+ REMOTE ER DISARM OUTPUT ARM OUTPUT ER OUTPUT INITI OUTPUT DIODE N00 WARNIN: DO NOT NET ANY OTHER AESSORY, INITI OR WIRE FROM THE REMOTE ER TO THE VEHILE OEM REMOTE REMAINS FUNTIAL DURIN REMOTE SEQUENE WHITE/BLA - IMMO. DA VEHILE SIDE WHITE/RED - IMMO. DA NETOR SIDE WHITE (N YELW (N BROWN/RED - ANH BROWN/YELW - ANL ORANE/BLA - OUTPUT ORANE/WHITE - RAP OUTPUT ORANE - IMMOBILIZER PIN/BLA (N PIN - INITI INPUT BLUE/RED (N BLUE/YELW (N REEN/RED RAY/RED - IMMOBILIZER DA RAY/YELW (N BLA (N *BLADE NETOR EX PIN-OUT WHITE/RED 0 0 WHITE/BLA WHITE 0 PIN/BLA PIN 0 BLA BROWN/RED BROWN/YELW ORANE/BLA 0 ORANE/WHITE ORANE 0 BLUE/RED 0 BLUE/YELW REEN/RED YELW RAY/RED 0 RAY/YELW BM (RM SA - DI ( M AR Y A O ENINE 0 0 0 OR N PI SEE VEHILE WIRE ROSS REFERENE HART (- S NETOR PT DO ER IV X DR 0 0 IMMOBILIZER NETOR N TO VOID THE OEM ALARM TROL BY DA: -NET ARM/ FROM THE RS TO THE BM -NET DISARM/UN FROM THE RS TO THE BM -NET MODULE REEN/RED WIRE TO ROUND X TA DA O. M IM O. M IM ARM/DISARM WARNIN: -THE MODULE DOES NOT TROL THE OEM ALARM ARM BY DA. -THE MODULE DOES TROL THE OEM ALARM DISARM BY DA. (INITI WILL TURN AND OFF E READ ARM/DISARM WARNIN Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of Doc. No.: ##0## 0 name type PoSItIon PolarItY MoDUle location component locator Year MoDel Juke MT DeScrIPtIon nissan Make TYPE - WIRE ROSS REFERENE HART - OF Immobilizer behind button 0 Immobilizer behind button M0 pin E 0 lutch switch ruise SW E pin 0 ray (OPEN lutch switch B0 pin Lt BM near A-pillar driver side Red BM near A-pillar driver side 0 BM near A-pillar driver side - lutch SW Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of 0 Doc. No.: ##0## TYPE - WIRIN DIARAM V OBDII NETOR ED UNDER DRIVER SIDE DASH 0 (+ NH A NL A SE UI R 0 TI NI I A ASD LUTH SWITH E - BROWN SW LUTH SWITH E - WHITE H UT L SW REMOTE ER DISARM OUTPUT ARM OUTPUT ROUND WHEN RUNNIN OUTPUT ER OUTPUT INITI OUTPUT DIODE N00 WARNIN: DO NOT NET ANY OTHER AESSORY, INITI OR WIRE FROM THE REMOTE ER TO THE VEHILE OEM REMOTE REMAINS FUNTIAL DURIN REMOTE SEQUENE WHITE/BLA - IMMO. DA VEHILE SIDE WHITE/RED - IMMO. DA NETOR SIDE WHITE (N YELW (N BROWN/RED - ANH BROWN/YELW - ANL ORANE/BLA - OUTPUT ORANE/WHITE - RAP OUTPUT ORANE - IMMOBILIZER PIN/BLA (N PIN - INITI INPUT BLUE/RED (N BLUE/YELW (N REEN/RED RAY/RED - IMMOBILIZER DA RAY/YELW (N BLA (N *BLADE NETOR EX PIN-OUT WHITE/RED 0 0 WHITE/BLA WHITE 0 PIN/BLA PIN 0 BLA BROWN/RED BROWN/YELW ORANE/BLA 0 ORANE 0 BLUE/RED 0 BLUE/YELW REEN/RED YELW RAY/RED 0 RAY/YELW ORANE/WHITE TO VOID THE OEM ALARM TROL BY DA: -NET ARM/ FROM THE RS TO THE BM -NET DISARM/UN FROM THE RS TO THE BM -NET MODULE REEN/RED WIRE TO ROUND 0 0 OR 0 0 BLA (- M0 - BROWN DO ER IV B0 BLA DR (M AR - ( M R SA IMMOBILIZER - WHITE S PT 0 DI ENINE A O TA DA O. M IM O. M IM BM NEAR A-PILLAR DRIVER SIDE N ARM/DISARM WARNIN: -THE MODULE DOES NOT TROL THE OEM ALARM ARM BY DA. -THE MODULE DOES TROL THE OEM ALARM DISARM BY DA. (INITI WILL TURN AND OFF E READ ARM/DISARM WARNIN N PI Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of Doc. No.: ##0## 0 nissan Quest w/ electric sliding door DeScrIPtIon name type PoSItIon PolarItY MoDUle location component locator Quest w/ electric sliding door Year MoDel Make TYPE - WIRE ROSS REFERENE HART - OF M Red Immobilizer behind button M 0 Immobilizer behind button - M0 pin 0 E switch reen M pin reen BM behind cluster M BM behind cluster M ray Immobilizer behind button M 0 Immobilizer behind button M0 pin 0 E switch reen M pin reen BM behind cluster M BM behind cluster - Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page 0 of 0 Doc. No.: ##0## TYPE - WIRIN DIARAM OBDII NETOR ED UNDER DRIVER SIDE DASH 0 TI NI I (+ NH A NL A WARNIN: IF THE REMOTE ER IS SET TO REARM AFTER, THE SEURITY LIHT WILL FLASH DURIN THE REMOTE SEQUENE BRAE SWITH E - WHITE E A BR (+ REMOTE ER ER OUTPUT INITI OUTPUT ARM OUTPUT DIODE N00 WARNIN: DO NOT NET ANY OTHER AESSORY, INITI OR WIRE FROM THE REMOTE ER TO THE VEHILE OEM REMOTE REMAINS FUNTIAL DURIN REMOTE SEQUENE WHITE/BLA - IMMO. DA VEHILE SIDE WHITE/RED - IMMO. DA NETOR SIDE WHITE (N YELW (N BROWN/RED - ANH BROWN/YELW - ANL ORANE/BLA - OUTPUT ORANE/WHITE - RAP OUTPUT ORANE - IMMOBILIZER PIN/BLA (N PIN - INITI INPUT BLUE/RED (N BLUE/YELW (N REEN/RED (N RAY/RED - IMMOBILIZER DA RAY/YELW (N BLA (N *BLADE NETOR EX PIN-OUT WHITE/RED 0 0 WHITE/BLA WHITE 0 PIN/BLA PIN 0 BLA BROWN/RED BROWN/YELW ORANE/BLA 0 ORANE/WHITE ORANE 0 BLUE/RED 0 BLUE/YELW REEN/RED YELW RAY/RED 0 RAY/YELW BM BEHIND LUSTER IMMOBILIZER M - WHITE A O N INSERT THE DIODE WIRE INTO THE EMPTY NETOR PIN, PRESS IT AAINST THE NETI AND SEURE IT INTO PLAE. TA DA O. M IM O. M IM ARM/DISARM WARNIN: -THE MODULE DOES NOT TROL THE OEM ALARM ARM BY DA. -THE MODULE DOES TROL THE OEM ALARM DISARM BY DA. (INITI WILL TURN AND OFF E ENINE DIODE N00 AR M DIODE 0 0 OR DO 0 0 M BLA (- S PT M0 BROWN ER IV DR (- N00 0 M BLA N PI Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of Doc. No.: ##0## 0 type PoSItIon PolarItY MoDUle location component locator - name Versa Note DeScrIPtIon - nissan Sentra Year MoDel Make TYPE - WIRE ROSS REFERENE HART - OF Immobilizer behind button 0 Immobilizer behind button M0 pin E switch B0 pin Yellow BM near A-pillar driver side BM near A-pillar driver side BM near A-pillar driver side Immobilizer behind button 0 Immobilizer behind button M0 pin or Red E switch Orange B0 pin Lt BM near A-pillar driver side ray BM near A-pillar driver side BM near A-pillar driver side Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of 0 Doc. No.: ##0## TYPE - WIRIN DIARAM OBDII NETOR ED UNDER DRIVER SIDE DASH 0 TI NI I (+ NH A NL A BRAE SWITH E A BR (+ REMOTE ER DISARM OUTPUT ARM OUTPUT ER OUTPUT INITI OUTPUT DIODE N00 WARNIN: DO NOT NET ANY OTHER AESSORY, INITI OR WIRE FROM THE REMOTE ER TO THE VEHILE OEM REMOTE REMAINS FUNTIAL DURIN REMOTE SEQUENE WHITE/BLA - IMMO. DA VEHILE SIDE WHITE/RED - IMMO. DA NETOR SIDE WHITE (N YELW (N BROWN/RED - ANH BROWN/YELW - ANL ORANE/BLA - OUTPUT ORANE/WHITE - RAP OUTPUT ORANE - IMMOBILIZER PIN/BLA (N PIN - INITI INPUT BLUE/RED (N BLUE/YELW (N REEN/RED RAY/RED - IMMOBILIZER DA RAY/YELW (N BLA (N *BLADE NETOR EX PIN-OUT WHITE/RED 0 0 WHITE/BLA WHITE 0 PIN/BLA PIN 0 BLA BROWN/RED BROWN/YELW ORANE/BLA 0 ORANE/WHITE ORANE 0 BLUE/RED 0 BLUE/YELW REEN/RED YELW RAY/RED 0 RAY/YELW BM IMMOBILIZER NETOR A O N TO VOID THE OEM ALARM TROL BY DA: -NET ARM/ FROM THE RS TO THE BM -NET DISARM/UN FROM THE RS TO THE BM -NET MODULE REEN/RED WIRE TO ROUND ENINE UN 0 NETOR WHITE PT S (RM /A ( RM ISA D / ( DR IV ER N PI 0 0 OR DO 0 0 TA DA O. M IM O. M IM ARM/DISARM WARNIN: -THE MODULE DOES NOT TROL THE OEM ALARM ARM BY DA. -THE MODULE DOES TROL THE OEM ALARM DISARM BY DA. (INITI WILL TURN AND OFF E READ ARM/DISARM WARNIN Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of Doc. No.: ##0## 0 ARTRIDE INSTALLI Slide cartridge into unit. Notice button under LED. Ready for Module Programming Procedure. MODULE PRORAMMIN PROEDURE - WITH N - OF NOTE I When programming, only one key fob will be used. The other one must be located at least 0 feet away from the vehicle. A : Press and release brake pedal once [x]. E N INE Remove valet key from keyfob. A MT: Press and release both brake and clutch pedals at the same time, once [x]. E N IN E A E N INE E N INE A Remove battery from keyfob. A LED will turn solid BLUE. Wait until the security light flashes. (This may take up to seconds : Press and release brake pedal once [x]. E N IN E MT: Press and release both brake and clutch pedals at the same time, once [x]. A E N IN E Place and hold keyfob on push start button. (No battery A E N INE E N INE! eyfob transponder is located behind keyfob logo. 0 IMPORTANT: Place and hold keyfob on push start button for steps to 0. A E N IN E x Push start button twice [x] to position. A E N IN E x Push start button once [x] to OFF position. Disconnect all s from remote starter except the power. Wait, LED will flash BLUE rapidly. A LED will turn solid RED. Wait until the security light flashes. (This may take up to seconds E N INE A È IMPORTANT: READ NEXT PAE! Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of Doc. No.: ##0## 0 MODULE PRORAMMIN PROEDURE - WITH N - OF Disconnect the power. Remove remote starter from vehicle. Place and hold keyfob on push start button. (No battery A A E N INE E N INE Wait until the security light turns OFF. onnect remote starter to computer.! Proceed with extended programming. IMPORTANT: Place and hold keyfob on push start button for steps to 0. A E N IN E x eyfob transponder is located behind keyfob logo. onnect remote starter to vehicle. 0 Push start button twice [x] to position. Wait, LED will turn solid BLUE for seconds. A E N IN E x Push start button once [x] to OFF position. Module Programming Procedure completed. Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of Doc. No.: ##0## 0 IDENTIFY VEHILE YEAR Locate the Vehicle Identification Number (VIN, identify the 0th character then match it to its corresponding year. AYNTALDR0X a 0 l 0 Y 000 a 00 B M 00 B 0 c n 0 c 0 D P 00 D 0 e r 00 e 0 f S 00 f 0 t 0 H V 00 H 0 J W 0 J 0 k X 00 k 0 MODULE DIANOSTIS led StatUS DIanoStIcS DUrIn ProraMMIn DUrIn remote Start WItH InItIon off Flashing RED Missing/wrong information from firmware or vehicle Incorrectly programmed Incorrectly programmed or connected Solid RED Waiting for more vehicle information Incorrectly programmed Not programmed waiting for more vehicle information Flashing BLUE Additional steps required to complete programming orrectly programmed and operational False ground when running status from remote starter Solid BLUE then OFF orrectly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FORY RESET PROEDURE DISNET cartridge from remote starter. PRESS AND HOLD programming button while re-connecting cartridge to remote starter. LED will flash red. Immediately RELEASE programming button. LED will turn solid red for seconds. RESET OMPLETED. RENET all s. Repeat programming procedure.! Failure to follow procedure may result with a DT or a HE ENINE error message. Automotive Data Solutions Inc.
INSTALL UIDE U.S. Patent No.,,0 Page of Doc. No.: ##0## 0 WARNIN: READ BEFORE REMOTE NOTIEIN THE VEHILE IMPORTANT I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction. TAE OVER PROEDURE - PUSH TO - TO THE VEHILE OWNER NOTE I TIME RESTRITIºN Within SEDS from previous step: All vehicle doors must be closed and locked prior to remote start sequence. È Open vehicle door. Enter vehicle. lose vehicle door. TIME RESTRITIºN OMIN UP! Press and release BRAE pedal. Unlock vehicle door using OEM or after-market remote, or door request switch. Take over procedure completed.! Failure to follow procedure will result in vehicle engine shutdown. Automotive Data Solutions Inc.