INSTALLATION INSTRUCTIONS - PDF Free Download

INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used) 2 Wire ties with large clips Control unit Flange bolt Buzzer Buzzer bracket Fuse label Control unit bracket 5 EPT sealers Switch 40 Wire ties (7 Not used) Ground bolt 9 Small wire ties 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 08V67-SJC-1002-91 1 of 28

2 Corner sensors 2 Well nuts 2 Center sensors Corrugated tube 2 Retainer clips 3 Cushion tapes (Some may not be used) Flange nut Washer-screw, 6 x 12 mm Accessory User s Information Manual 6 Oval grommets Tailgate switch Round grommet Tailgate switch bracket 7 Clips Template 4 Washer-screws, 4 x 14 mm 2 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Small flat-tip screwdriver 10 mm Combination wrench 10 mm and 14 mm Sockets Pushpin Ratchet 3 mm and 8 mm Drill bits Eye protection (face shield, safety goggles, etc.) File Diagonal cutters Tape measure Isopropyl alcohol Shop towel 20 mm and 26 mm Hole saws Drill Utility Knife Scissors T-30, T-40, and T-50 Torx drivers Insulation tape Center punch 4 mm Hex wrench Torque wrench Touch-up paint Blanket Adhesive tape Plastic trim tool T/N SILTRIMTL10 INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 3. Remove the left dashboard side cover (seven clips). 7 CLIPS LEFT DASHBOARD SIDE COVER 7D2002AX Illustration of the Back-Up Sensors Installed on the Vehicle SWITCH BUZZER TAILGATE SWITCH CONTROL UNIT CORNER CORNER 7D2001AX CENTER 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 3 of 28

4. Remove the driver s dashboard lower cover (one self-tapping screw, nine clips, unplug the vehicle connectors, and the vehicle tube). 6. Remove the passenger s console side trim (two clips and retaining tab). SELF-TAPPING SCREW S TUBE DRIVER S DASHBOARD LOWER COVER 9 CLIPS 7D2003AX 5. Remove the driver s console side trim (three clips and one retaining tab). DASHBOARD CENTER LOWER COVER DASHBOARD CENTER LOWER COVER 2 CLIPS 7. Open the center pocket, and pull the center pocket out towards you. DASHBOARD CENTER LOWER COVER CENTER POCKET RETAINING TAB PASSENGER S CONSOLE SIDE TRIM 7D2005AX RETAINING TAB CENTER POCKET Open. 841020AB DRIVER S CONSOLE SIDE TRIM 3 CLIPS 7D2004AX 4 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

8. Remove the dashboard center lower cover (three self-tapping screws, five clips, six retaining tabs, and unplug the vehicle connectors). 10. Pull back the weatherstrip from the left kick panel. Remove the left kick panel (one screw clip and one clip). S 3 CLIPS WEATHERSTRIP SCREW CLIP 4 6 RETAINING TABS CLIP 3 SELF- TAPPING SCREWS LEFT KICK 7D2008AX 2 CLIPS DASHBOARD CENTER LOWER COVER 7D2006BX 9. Remove the fuel fill door release handle. Remove the left front door sill trim (three clips and three retaining tabs). 11. Remove the left rear door sill trim (three clips and four retaining tabs). 4 RETAINING TABS 3 CLIPS 4 2 RETAINING TABS 2 CLIPS 4 FUEL FILL DOOR RELEASE HANDLE CLIP 4 RETAINING TABS LEFT REAR DOOR SILL TRIM 7D2009AX 4 LEFT DOOR SILL TRIM 4 RETAINING TAB 7D2007AX 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 5 of 28

If the vehicle is equipped with a left seat belt lower anchor bolt, continue with step 12. If not, go to step 14. 12. Pull up the left seat belt lower anchor bolt cover, and remove the left seat belt lower anchor bolt. 15. Lift the rear seat cushion. REAR SEAT CUSHION LEFT B-PILLAR LOWER TRIM 4 CLIPS RIGHT REAR UNDER-SEAT TRIM LEFT SEAT BELT LOWER ANCHOR BOLT COVER LEFT SEAT BELT LOWER ANCHOR 7D2010BX BOLT 13. Remove the left B-pillar lower trim panel by pulling it out toward you as shown. Go to step 15. 7 CLIPS LEFT REAR UNDER- SEAT TRIM 7D2012AX 16. Remove the left rear under-seat trim panel (seven clips). 17. Remove the right rear under-seat trim panel (four clips). 14. Remove the left B-pillar lower trim panel by pulling it out toward you as shown. LEFT B-PILLAR LOWER TRIM 7D2011BX 6 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

18. Remove the left and right rear seat mount covers (four clips). RIGHT REAR SEAT MOUNT COVER LOWER MIDDLE REAR SEAT MOUNT COVER UPPER MIDDLE REAR SEAT MOUNT COVER 2 CLIPS 21. Remove the nine anchor bolts. REAR SEAT ANCHOR BOLTS REAR SEAT BELT BUCKLE ANCHOR BOLTS REAR SEAT 2 CLIPS 2 CLIPS 9 RETAINING TABS 2 CLIPS LEFT REAR SEAT MOUNT COVER REAR SEAT ANCHOR BOLTS REAR SEAT BELT ANCHOR BOLT REAR SEAT BELT REAR SEAT ANCHOR BOLTS 7D2014AX 19. Remove the upper middle rear seat mount cover (hold the seat belt buckles down, and pull up to release the two clips and nine retaining tabs). 20. Remove the lower middle rear seat mount cover (two clips). 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 7 of 28

22. Remove two caps from the rear trim panel cover (eight retaining tabs). REAR SEAT 4 RETAINING TABS CAP REAR TRIM COVER 4 RETAINING TABS CAP 25. Remove the right rear seat belt upper anchor bolt cover (three retaining tabs), and remove the right rear seat belt upper anchor bolt. WEATHERSTRIP CLIP RIGHT REAR SEAT BELT UPPER ANCHOR BOLT 3 RETAINING TABS CLIP RIGHT C-PILLAR UPPER TRIM RIGHT REAR SEAT BELT UPPER ANCHOR BOLT COVER 7D2017BX 7D2015AX 23. Remove the rear seat. Have an assistant help you. 24. Remove the rear trim panel cover (two clips, two retaining tabs, and six clips). RETAINING TAB REAR TRIM COVER 6 CLIPS 26. Pull back the weatherstrip from the right C-pillar upper trim. Remove the right C-pillar upper trim. With side airbag; release the clip partway, and remove the right C-pillar trim by releasing the one clip. Without side airbag; remove the right C-pillar trim by releasing the two clips. 27. Remove the right rear door sill trim (three clips and four retaining tabs). 3 CLIPS RETAINING TABS RETAINING TAB 2 CLIPS 7D2016AX RETAINING TABS RIGHT REAR DOOR SILL TRIM 832511AX 8 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

28. Pull up the right rear seat belt lower anchor bolt cover, and remove the right rear seat belt lower anchor bolt. RIGHT C-PILLAR LOWER TRIM REAR TRIM CLIP 2 CLIPS RIGHT REAR SEAT BELT LOWER ANCHOR BOLT RIGHT REAR SEAT BELT LOWER ANCHOR BOLT COVER 7D2018CX 29. Remove the upper clip, then remove the right C-pillar lower trim by releasing the two clips. 30. Repeat steps 25 through 29 to remove the left C-pillar upper and lower trim. If the vehicle is equipped with a subwoofer, continue with step 31. If not, go to step 32. 31. Unplug the vehicle connector. Remove the four bolts, and remove the subwoofer by pulling upward to release the two hooks. 33. Remove two roof rear trim bolt covers (six retaining tabs). Remove two roof trim nuts. 3 RETAINING TABS ROOF TRIM NUT 3 CLIPS ROOF REAR TRIM BOLT COVER 3 RETAINING TABS ROOF REAR TRIM BOLT COVER ROOF TRIM NUT 7D2020AX 2 HOOKS ROOF TRIM 7D2021AX SUBWOOFER 4 BOLTS 7D2019AX 32. Remove the rear trim panel (three clips). 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 9 of 28

34. Using a plastic trim tool, carefully pry up the front of the roof trim to release the three front clips. Start with the left clip, and work your way to the right clip. 38. Remove seven vehicle grommets from the roof panel, and install six new oval grommets and one new round grommet into the roof panel as shown. 7 CLIPS PLASTIC TRIM TOOL NEW ROUND GROMMET ROOF ROOF TRIM GROMMET Discard. 6 NEW OVAL GROMMETS LEFT CLIP Start here. RIGHT CLIP Finish here. 7D2022BX 6 GROMMETS Discard. 7D2024AX 35. Gently lift the front of the roof trim to release four remaining clips. 36. Gently pull up the roof trim by releasing two hooks. 39. On the roof trim backside, remove seven vehicle clips from the roof trim, and install seven new clips to the roof trim. ROOF TRIM ROOF TRIM 2 HOOKS HIGH-MOUNT BRAKE LIGHT GROMMET 7 NEW CLIPS ROOF 2 S ANTENNA GROMMET 7D2023BX 7 CLIPS Discard. 7D2025AX 37. Remove the antenna grommet and high-mount brake light grommet from the roof panel, unplug the vehicle connectors, and remove the roof trim. 10 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

40. Remove the screw cover from the rear of the right bed rail trim (four retaining tabs). 43. Remove the right C-pillar outer trim (slide rearward, and unplug the vehicle connector). 6 CLIPS SCREW COVER 4 RETAINING TABS 3 CLIPS Remove. RIGHT C-PILLAR OUTER TRIM HOLDER 3 CLIPS Install. SELF- TAPPING SCREW RIGHT BED RAIL TRIM RIGHT C-PILLAR OUTER TRIM 3 CLIPS 852225AB 7D2029AX 41. Remove one self-tapping screw from the rear of the right bed rail trim. 42. Pull the right bed rail trim back to release the six clips, and remove the right bed rail trim. 44. Remove the three vehicle clips from the vehicle panel, and install them to the right C-pillar outer trim holder. 45. Remove the right front upper tie-down hook (two T-50 torx bolts). Repeat the same procedure for the left side. RIGHT UPPER TIE-DOWN HOOK T-50 TORX BOLTS 852226AB 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 11 of 28

46. Remove the front board panel (six T-40 torx bolts). If the vehicle is equipped with a bed extender, continue with step 48. If not, go to step 49. 48. Remove the right latch (three hex bolts). RIGHT SIDE BED LINING 6 T-40 TORX BOLTS BOARD 7D2028AX HEX BOLTS 47. Remove two right rear tie-down hooks (four T-50 torx bolts). RIGHT LATCH 7D2031BX 49. Remove the right side bed lining (five T-40 torx bolts, one clip, and unplug the vehicle connector). CLIP RIGHT SIDE BED LINING 2 RIGHT REAR TIE-DOWN HOOKS 5 T-40 TORX BOLTS T-50 TORX BOLTS 7D2030BX 7D2032BX 12 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

50. Remove the left taillight (two bolts, two clips, release the vehicle connectors from the vehicle panel, and unplug the vehicle connector). Repeat the same procedure for the right side. 51. Remove the right license plate light (three retaining tabs and unplug the vehicle connector). Repeat the same procedure for the left side. LEFT SIDE RIGHT SIDE 3 RETAINING TABS RIGHT LICENSE PLATE LIGHT S S BOLTS 2 CLIPS REAR BUMPER 841501AY LEFT TAILLIGHT 7D2033AX 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 13 of 28

52. Remove the license plate from the rear bumper (two bolts). 53. Remove the rear bumper (two bolts, ten self-tapping screws, and six clips). Have an assistant help you. Place the rear bumper on a blanket. With rear under spoiler Without rear under spoiler REAR BUMPER LICENSE PLATE REAR BUMPER LICENSE PLATE BOLTS 2 CLIPS BOLTS 2 SELF- TAPPING SCREWS 2 CLIPS 2 SELF- TAPPING SCREWS REAR BUMPER BOLTS REAR BUMPER 4 CLIPS 8 SELF-TAPPING SCREWS 841601AY 8 SELF- TAPPING SCREWS BOLTS 4 CLIPS REAR UNDER Remove these clips. SPOILER REAR BUMPER 7D2034BX 14 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

54. On the inside of the rear bumper, locate the back-up sensor preset marks on the left side. Using a pushpin, pierce the holes at the left and center preset marks. There are two sets of marks on the rear bumper, use the lower marks. Repeat the same procedure for the right side. If the vehicle is equipped with a rear under spoiler, continue with step 56. If not, go to step 57. 56. Remove the left and right bumper absorbers. Locate the scribe mark on the left bumper absorber. Using a utility knife, cut out the left bumper absorber along the scribe mark as shown. Repeat the same procedure for the right bumper absorber. Go to step 58. MARKS Do not use these marks. LEFT PRESET MARK REAR BUMPER LEFT BUMPER ABSORBER CENTER PRESET MARK PUSHPIN 7D2035AX 55. While wearing eye protection, drill one 20 mm hole through the outer mark, and one 26 mm hole through the inner mark on the rear bumper. First drill with a 3 mm drill bit. Finish the outer hole with a 20 mm hole saw. Finish the inner hole with a 26 mm hole saw. Remove any burrs. Repeat the same procedure for the right side. Cut out. LEFT BUMPER ABSORBER SCRIBE MARK 832601AX REAR BUMPER MARKS 3 mm DRILL BIT 3 mm DRILL BIT 20 mm HOLE SAW DRILL 26 mm HOLE SAW DRILL 7D2037AX 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 15 of 28

57. Remove the left and right bumper absorbers. Locate the scribe mark on the left bumper absorber. Using a utility knife, cut out the left bumper absorber along the scribe mark as shown. Repeat the same procedure for the right bumper absorber. 58. Slide the two center sensors into the 26 mm holes with the UP mark facing up. Secure the center sensors with two retainer clips. RETAINER CLIP View of the top side LEFT BUMPER ABSORBER UP MARK CENTER 15 mm REAR BUMPER LEFT BUMPER ABSORBER Cut out. 15 mm 35 mm SCRIBE MARK Cut out. 26 mm HOLE CORNER CORNER CENTER 20 mm HOLE CENTER CORNER LEFT BUMPER ABSORBER 7D2039AX CORNER TRIM CORNER UP MARK UP MARK 7D2038AX 59. Separate the corner sensors from the corner sensor trims. First install the corner sensor trim into the 20 mm holes with the UP mark facing up, then install the corner sensors through the corner sensor trim with the UP mark on the sensor facing up. 16 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

60. Place a shop towel below the tailgate latch to catch any metal shavings. Attach adhesive tape inside the tailgate panel with the tape adhesive facing up to catch any metal shaving. ADHESIVE TAPE Position with adhesive facing up. TAILGATE LATCH 62. While wearing gloves and eye protection, drill one 26 mm hole and four 8 mm holes through the marked locations. First drill with a 3 mm drill bit, then finish the center hole with a 26 mm hole saw. Finish the outer holes with an 8 mm drill bit. 5 MARKS 3 mm DRILL BIT 26 mm HOLE SAW TAILGATE SHOP TOWEL 7D2107AX 3 mm 8 mm DRILL BIT DRILL 7D2109AX 61. Position the template on the tailgate panel. Using a center punch, mark the tailgate panel at five holes indicated on the template. Remove the template. TAIL- GATE 5 MARKS CENTER PUNCH 63. Remove any burrs from the edges of the holes, and apply touch-up paint. Allow the touch-up paint to dry thoroughly before proceeding to the next step. Remove the shop towel, adhesive tape, and any metal shavings. 64. Insert two well nuts into the upper and lower holes. UPPER HOLE TEMPLATE 2 WELL NUTS 2 WASHER- SCREWS, 4 x 14 mm TEMPLATE 7D2108BX LOWER HOLE TAILGATE SWITCH BRACKET 7D2110AX 65. Install the tailgate switch bracket to the vehicle with two 4 x 14 mm washer-screws. 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 17 of 28

66. Cut 50 mm from the end of the corrugated tube. CORRUGATED TUBE 69. Attach the 2A fuse label to the back-up sensor harness fuse case. 50 mm FUSE CASE 2-PIN Align. FUSE LABEL (2A) Discard. CORRUGATED TUBE INSULATION TAPE WIRE TAILGATE SWITCH 7D2111AX 7D2041AX 67. Install the corrugated tube around the wires on the tailgate switch, align the corrugated tube to the 2-pin connector, and secure the tube to the tailgate switch with insulation tape. 68. Insert the tailgate switch 2-pin connector into the 26 mm hole, and install the tailgate switch onto the tailgate switch bracket with two 4 x 14 mm washer-screws. TAILGATE SWITCH BRACKET 2 WASHER- SCREWS, 4 x 14 mm TAILGATE SWITCH 2-PIN TAILGATE SWITCH 7D2112AX 18 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

70. Inside the passenger s compartment, remove the two vehicle foam blocks from the vehicle panel. 73. Install the back-up sensor harness grommet into the vehicle grommet hole. PASSENGER S COMPARTMENT INSIDE OUTSIDE FOAM BLOCKS GROMMET HOLE GROMMET GROMMET Discard. GROMMET HOLE 7D2101AX 7D2042BX 71. Inside the cargo area, remove the vehicle grommet from the vehicle panel. 72. Route the back-up sensor harness into the vehicle grommet hole, and into the passenger s compartment. 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 19 of 28

74. Install a wire tie with small clip at the green tape on the back-up sensor harness as shown. Inside the cargo area, route the back-up sensor harness along the vehicle harness, and secure the front of the back-up sensor harness to the hole in the vehicle panel with one wire tie with small clip. 77. Route the back-up sensor harness along the vehicle harness, and through the right taillight opening. Secure the back-up sensor harness to the vehicle harness with three wire ties. WIRE TIE WITH SMALL CLIP HOLE WIRE TIE WITH LARGE CLIP Not used here. Large Small WIRE TIE WITH SMALL CLIP Use this clip. RIGHT TAILLIGHT OPENING GREEN TAPE WIRE TIES WIRE TIES WIRE TIES WIRE TIE 7D2103AX 78. Using scissors, cut a EPT sealer into three equal pieces. EPT SEALER 7D2102CX EPT SEALER 75. Secure the back-up sensor harness to the vehicle harness with five wire ties. 76. Using isopropyl alcohol on a shop towel, clean the area near the wire tie with small clip where the EPT sealer will attach. Secure the back-up sensor harness to the vehicle panel with one EPT sealer. 7D2133BX 20 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

79. Using isopropyl alcohol on a shop towel, clean the areas where the EPT sealers will attach. Attach two pieces of EPT sealer to the edge of the vehicle panel as shown. 82. Route the back-up sensor harness along the rear bumper area, and secure it to the vehicle harness with eight wire ties. TAILGATE EPT SEALER TAILGATE WIRE TIES WIRE TIES 7D2113CX 80. Plug the back-up sensor harness 2-pin connector into the tailgate switch 2-pin connector. 2-PIN TAILGATE SWITCH 2-PIN EPT SEALER GREEN TAPE 7D2104BX 83. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Secure the back-up sensor harness to the vehicle panel with one EPT sealer at the green tape. EPT SEALER TAILGATE SWITCH 2-PIN 7D2114BX 81. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Secure the back-up sensor harness to the vehicle frame with one piece of EPT sealer. 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 21 of 28

84. Using scissors, cut one EPT sealer in half. EPT SEALER Cut in half. 2 PIECES OF EPT SEALER 2 2-PIN S 87. Under the rear bumper, secure the center sensor 2-pin connectors and the center sensor harnesses to the vehicle brackets with two wire ties with large clips as shown. 2 CENTER 2-PIN S WIRE TIES WITH LARGE CLIPS 2 CENTER 2-PIN S BRACKET REAR BUMPER 2 CENTER ES BRACKET BACK BRACKET Large Small REAR BUMPER BRACKET 2 CORNER 2-PIN S 2 2-PIN S 7D2105BX 85. Reinstall the bumper absorbers. With the help of an assistant, hold the rear bumper close to the vehicle. Route the back-up sensor harness 2-pin connectors through the holes in the bumper absorbers, and plug them to the corner sensor and the center sensor 2-pin connectors. WIRE TIE WITH LARGE CLIP Use this clip. WIRE TIE WITH SMALL CLIP Not used here. 7D2106FX 86. Wrap two pieces of EPT sealer around the center sensor 2-pin connectors, and reinstall the rear bumper. 22 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

88. Inside of the vehicle, pull back the floor mat. Route the back-up sensor harness across the vehicle panel and alongside the vehicle harness. FOAM BLOCKS CUSHION TAPE 2 CUSHION TAPES Cut in half. 92. Slide the control unit bracket onto the control unit. CONTROL UNIT BRACKET CONTROL UNIT WIRE TIES WIRE TIE FLOOR MAT 7D2115CX 89. Using scissors, cut two cushion tapes in half. Using isopropyl alcohol on a shop towel, clean the areas where the cushion tapes will attach. Secure the back-up sensor harness to the vehicle panel with three pieces of cushion tape. 90. Secure the back-up sensor harness to the vehicle harness with four wire ties. Do not secure the wire tie to the SRS harness. 91. Reinstall the two vehicle foam blocks removed in step 70. 7D2116AX 93. Plug the back-up sensor harness 22-pin connector into the control unit, and insert the control unit bracket into the hole in the vehicle panel. Secure the control unit bracket with one flange bolt. CONTROL UNIT BRACKET HOLE FLANGE BOLT CONTROL UNIT 22-PIN 7D2117AX 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 23 of 28

94. Unplug the vehicle 23-pin and 14-pin connectors. Release the connector lock on the vehicle 23-pin connector. SIDE VIEW 23-PIN LOCK 23-PIN 96. Route the back-up sensor harness along the vehicle harness, and secure it to the vehicle harness with four wire ties and two small wire ties in the area shown. WIRE TIES TERMINAL 23-PIN TERMINAL TERMINAL LOCK 14-PIN 23-PIN WIRE TIES SMALL WIRE TIES 7D2119AX 97. Route the back-up sensor harness along the vehicle harness, and secure it to the vehicle harness with four small wire ties. SMALL WIRE TIE 7D2118AX 95. Push the back-up sensor harness terminal into the vehicle 23-pin connector, then reattach the connector lock. Re-plug the vehicle 23-pin and 14-pin connectors. SMALL WIRE TIES 7D2120AX 24 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

98. Route the back-up sensor harness along the vehicle harness, and secure it to the vehicle harness with three small wire ties. 100. Route the back-up sensor harness as shown, and secure it to the vehicle harness and the vehicle frame with six wire ties. WIRE TIES FRAME WIRE TIES SMALL WIRE TIES 7D2121AX FUSE BOX Do not close the clip hole. 99. At the fuse box, remove the upper hood opener bolt. Secure the back-up sensor harness ground terminal with the ground bolt. WIRE TIES 7D2123AX FUSE BOX UPPER HOOD OPENER BOLT Discard. If the vehicle is equipped with a security system: Wrap one cushion tape around the back-up sensor harness, and secure it to the security system bracket with one wire tie. WIRE TIE GROUND BOLT HOOD OPENER GROUND TERMINAL 7D2122BX SECURITY SYSTEM BRACKET CUSHION TAPE 7D2124AX 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 25 of 28

101. Route the back-up sensor harness along the vehicle harness, and secure it to the vehicle harness with three wire ties. If there is any excess, bundle it to the vehicle harness after step 105. WIRE TIE 103. Remove the front vehicle bolt from the vehicle frame, and loosen the back vehicle bolt. BUZZER 5-PIN FRAME WIRE TIES 7D2125BX 102. Install the buzzer bracket to the buzzer with one 6 x 12 mm washer-screw and one flange nut. Do not pinch the wire on the buzzer. FLANGE NUT BOLT Remove. BUZZER BRACKET BACK BOLT Loosen. 7D2127AX 104. Plug the back-up sensor harness 5-pin connector into the buzzer. 105. Insert the buzzer bracket between the vehicle frame and the back vehicle bolt, and install the buzzer bracket to the vehicle frame with two bolts. 106. Using a pushpin, mark the inside of the driver s dashboard lower cover at the preset mark. BUZZER PUSHPIN BUZZER BRACKET WASHER- SCREW, 6 x 12 mm 7D2126AX PRESET MARK DRIVER S DASHBOARD LOWER COVER 7D2128AX 26 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.

107. While wearing eye protection, drill one 26 mm hole through the marked position. First drill with a 3 mm drill bit, then finish with a 26 mm hole saw. Remove any burrs. 109. Plug the back-up sensor harness 3-pin connector into the switch. 3 mm DRILL BIT DRILL DRIVER S DASHBOARD LOWER COVER 26 mm HOLE SAW MARK SWITCH 3-PIN 7D2131AX 7D2129BX 108. Reinstall the driver s dashboard lower cover. Insert the switch connector into the hole in the driver s dashboard lower cover, then turn the switch to install it to the driver s dashboard lower cover. 110. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Attach the EPT sealer to the driver s console side trim in the area shown. EPT SEALER DRIVER S DASHBOARD LOWER COVER HOLE DRIVER S CONSOLE SIDE TRIM 7D2132AX SWITCH SWITCH 7D2130AX 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 46956 (1111) 27 of 28

111. Check that all wire harnesses are routed properly and all connectors are plugged in. 112. Reinstall all removed parts. Check that all clips and fasteners are installed securely. NOTE: Torque the seat belt upper anchor bolts (steps 25 and 28) to 32 N m (24 lb-ft). Use these torque specs when reinstalling the anchor bolts to the rear seat (step 21): - Rear seat belt anchor bolt, 32 N m (24 lb-ft) - 6 rear seat belt buckle anchor bolts, 22 N m (16 lb-ft) - 2 rear seat anchor bolts, 47 N m (35 lb-ft) If reinstalling the left seat belt lower anchor bolt cover (step 12), torque the bolt to 32 N m (24 lb-ft). 113. Reconnect the negative cable to the battery. 114. Enter the customer s radio anti-theft code, and reset the radio station presets. 115. Reset the clock. 116. Check the operation of the back-up sensors according to the Accessory User s Information Manual. NOTE: Whenever the battery is disconnected, the driver s window AUTO function is disabled. 117. Start the engine. Push down on the driver s window switch until the window is fully open. 118. Pull up on the driver s window switch to close the window completely, then hold the switch for 2 seconds or more. 119. Test the window AUTO function. 28 of 28 AII 46956 (1111) 2011 American Honda Motor Co., Inc. All Rights Reserved.