Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-FM FM Available for : ADS-AL CA Rev. Date: March 9, 0 Doc. No.: ##885## 006 Version FRançaise disponible en ligne au www.idatalink.com please visit www.idatalink.com/support for complete product details The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 0 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
Page of 8 ADS-AL(DL)-FM Doc. No.: ##885## 006 install TYPE SELECTiOn features Make MoDel Year InStall type PUSH to Start ctrl relay ctrl for optional ring arm oem alarm DISarM oem alarm Door lock Door Unlock PrIorItY Unlock auto climate ctrl comfort WInDoW roll DoWn comfort WInDoW roll UP after Market alarm ctrl from oem remotes HeateD SeatS ctrl cooling SeatS ctrl rear DefroSt ctrl rap SHUtDoWn ctrl ford tachometer output lincoln Brake PeDal Stat output e-brake output Door Stat output trunk Stat output HooD Stat output Taurus push to start 0- MKS push to start 09- MKT push to start 0- www.idatalink.com/support Automotive Data Solutions Inc. 0
Page of 8 ADS-AL(DL)-FM Doc. No.: ##885## 006 PUSH TO STArT VEHiCLE notice TAKE OVEr PrOCEDUrE NOTE I WARNING: All vehicle doors must be closed and locked prior to remote start sequence. TIME RESTRICTIN Within 45 SECONDS from previous step: Open vehicle door. TIME RESTRICTIN COMING UP Enter vehicle. Press and release BRAKE pedal. Press UNLOCK on after-market remote or OEM fob. Push to Start vehicle take over procedure completed. Failure to follow procedure within time restriction will result in vehicle engine shutdown. notice - BATTErY removal FrOM KEYFOB Before completing installation, open key fob. Remove battery. WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) notice - COOLED SEATS - HEATED SEATS - AUTO CLiMATE SolUtIon SolUtIon Install a toggle switch and ground the wire of the selected feature. When the switch is activated it will turn on the selected feature, 5 seconds after remote start. WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) A negative pulse will trigger the selected feature during remote start. REMOTE STARTER AUX AUX AUX YELLOW/BLACK (NC) YELLOW/RED (NC) YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - AUTO CLIMATE ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK (NC) BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED - COOLED SEATS GREEN/YELLOW (NC) GRAY/RED - HEATED SEATS/DEFROST GRAY/YELLOW (NC) YELLOW/BLACK (NC) YELLOW/RED (NC) YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - AUTO CLIMATE ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK (NC) BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED - COOLED SEATS GREEN/YELLOW (NC) GRAY/RED - HEATED SEATS/DEFROST GRAY/YELLOW (NC) Use toggle switch to activate or deactivate the selected feature. Activate using a ground pulse. www.idatalink.com/support Automotive Data Solutions Inc. 0
Page 4 of 8 ADS-AL(DL)-FM Doc. No.: ##885## 006 COMPOnEnT LOCATOr C B D A lincoln MkS : Backup transceiver located behind key dock in glove box ford taurus & lincoln Mkt : Backup transceiver located behind key dock in armrest compartment www.idatalink.com/support Automotive Data Solutions Inc. 0
Page 5 of 8 ADS-AL(DL)-FM Doc. No.: ##885## 006 TYPE - wire CrOSS reference CHArT Make MoDel Year WIre DeScrIPtIon name connector color type PoSItIon WIre color PolarItY location component locator ford lincoln Taurus push to start 0- MKS push to start 09- MKT push to start 0- CANH C5D White pin Gray/Orange (DATA) RFA A CANL C5D White pin Violet/Orange (DATA) RFA A Accessory C5D White pin 8 Violet/Brown (+) RFA A Push button C5E Brown pin 4 Yellow/Orange (-) RFA A V C5C Blue pin Blue/Red (+) RFA A Brake C5E Brown pin VIolet/White (+) RFA A Trunk Yellow/Orange (-) At switch D Parklights Gray (-) At switch B CANH C5D White pin Gray/Orange (DATA) RFA A CANL C5D White pin Violet/Orange (DATA) RFA A Accessory C5D White pin 8 Violet/Brown (+) RFA A Push button C5E Brown pin 4 Yellow/Orange (-) RFA A V C5C Blue pin Blue/Red (+) RFA A Brake C5E Brown pin VIolet/White (+) RFA A Trunk Gray/Yellow (-) At switch D Parklights Gray (-) At switch B CANH C5D White pin Gray/Orange (DATA) RFA A CANL C5D White pin Violet/Orange (DATA) RFA A Accessory C5D White pin 8 Violet/Brown (+) RFA A Push button C5E Brown pin 4 Yellow/Orange (-) RFA A V C5C Blue pin Blue/Red (+) RFA A Brake C5E Brown pin Yellow/Green (+) RFA A Trunk Gray/Yellow (-) At switch C Parklights Gray (-) At switch B www.idatalink.com/support Automotive Data Solutions Inc. 0
Page 6 of 8 ADS-AL(DL)-FM Doc. No.: ##885## 006 TYPE - wiring DIAGRAM CANL POWER (+) CANH IGNITION (+) DIODE N400 BRAKE (+) 5-6 LOOPS ON BACKUP TRANSCEIVER SEE COMPONENT LOCATOR 5 4 5 4 5 4 7 6 7 6 7 6 0 9 8 0 9 8 0 9 8 0 9 8 7 6 5 4 0 9 8 7 6 5 4 0 9 8 7 6 5 4 5-6 LOOPS AROUND KEYFOB WITHOUT BATTERY SEE NOTICE C5C - BLUE CONNECTOR C5D - WHITE CONNECTOR C5E - BROWN CONNECTOR PUSH 87 V (+) 85 87A 86 0 RFA MODULE REMOTE STARTER RELAY MUST BE NEAR KEYFOB AND BACKUP TRANSCEIVER AVAILABLE ONLY WHEN VEHICLE IS NOT STARTED TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT WINDOW ROLL DOWN WINDOW ROLL UP UNLOCK (-) OUTPUT LOCK (-) OUTPUT V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT DATA MODE <- OPTIONAL <- OPTIONAL STARTER (+) OUTPUT IGNITION (+) BRAKE (+) INPUT V (+) INPUT TRUNK (-) OUTPUT PARKING LIGHT (-) OUTPUT HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT VEHICLE SWITCH VEHICLE SWITCH LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARDWIRE MODE DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK (NC) RED/WHITE (NC) BROWN WINDOW ROLL UP - PURPLE/YELLOW WINDOW ROLL DOWN - PURPLE/BLACK (NC) WHITE STARTER (+) INPUT - BLACK/WHITE *E-BRAKE STATUS (-) OUTPUT - GREEN *TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK WHITE/RED (NC) WHITE - GROUND (-) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - HOOD STATUS (-) OUTPUT* BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK - AUTO CLIMATE ORANGE/WHITE - PUSH ORANGE - BRAKE (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED - COOLED SEATS GREEN/YELLOW (NC) GRAY/RED - HEATED SEATS/DEFROST GRAY/YELLOW (NC) READ: NOTICE - COOLED SEATS - HEATED SEATS - AUTO CLIMATE www.idatalink.com/support Automotive Data Solutions Inc. 0
Page 7 of 8 ADS-AL(DL)-FM Doc. No.: ##885## 006 installation MODE SELECTiOn Press and release programming button to select installation mode. LED flashes (X) once = DATA MODE LED flashes (X) twice = STANDARD HARDWIRE MODE Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PrOgrAMMing PrOCEDUrE NOTE I Between each step, LED will turn solid RED, this is the default standby mode. Press on the brake pedal and push start button once [x] to START position. x ENGINE START STOP 4 x ENGINE START STOP Wait, LED will turn solid GREEN then will turn OFF. Push start button once [x] to OFF position. Module Programming Procedure completed. www.idatalink.com/support Automotive Data Solutions Inc. 0
Page 8 of 8 ADS-AL(DL)-FM Doc. No.: ##885## 006 identify VEHiCLE YEAr Locate the Vehicle Identification Number (VIN) and identify the 0th character. 4 A 5 Y N 5 T A L 8 D 5 R 0 X Match the VIN s 0th character to its corresponding year. l > 990 S > 995 Y > 000 5 > 005 a > 00 M > 99 t > 996 > 00 6 > 006 B > 0 n > 99 V > 997 > 00 7 > 007 c > 0 P > 99 W > 998 > 00 8 > 008 D > 0 r > 994 X > 999 4 > 004 9 > 009 e > 04 led StatUS Flashing RED DIaGnoStIcS DUrInG ProGraMMInG DUrInG remote Start WItH IGnItIon off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DiAgnOSTiCS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTOrY reset PrOCEDUrE DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. 4 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. When LED flashes red, RELEASE programming button. 7 Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. www.idatalink.com/support Automotive Data Solutions Inc. 0