F-86 SRE Scale EDF Radio ontrol model airplane Model No : FF-D005 Wingspan : 0mm UNDER SFETY PREUTIONS This radio control is not a toy! - lways keep this instruction manual ready on hand for quick reference. - ssemble this kit only places out of children reach. - First-time builders of EDF model should seek the advice of experienced modellers before beginning assembly and if they do not fully understand any parts of the construction. - Taking out liability insurance is recommended. - You are responsible for this model s assembly and safe operation. You need to purchase the following accessories separately to complete the assembly.. Signal cable (Throttle) pc required 5. 60 Electric Speed ontrol (ES) w/e 60 w/ E pc required. Signal cable (Elevator) 6. 36 rushless Motor, 600-800kv, Shaft dia 5mm pcs required pc required 3. Signal cable (lieron) 7. Micro servo, 8g, torque >.0kg pcs required 5 pcs required. Silicone attery cable (No. WG or WG) pc required 8. Li-Po attery, 5-cells (8.5v), 3600mh, 0 pc required opyright 007 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
Warning! First-time fliers should seek advice on pre-flight adjustments and assembly from experienced fliers. Remember that flying a badly assembled or badly adjusted aircraft is very dangerous! In The beginning, novice fliers should always be assisted by an experienced flier and should never fly alone! This model aircraft is designed to be powered by an electric-motor. Installing a over power motor and engine, or flying this model aggressively may lead to serious damage and accidents! Kit contents anopy Fuel Tank anopy lock 6 30x0x3mm plywood Fuselage 3 0 Horn 3xmm Screw 7 8 Linkage stopper 9 5 6 3 Landing gear x 30 mm wire 0 Wing 7 8 9 3 x 5mm wire x 00mm wire x 65mm wire 3 3 3 x 0mm wire 0x0x3mm plywood 0 x30mm screw 5 3 x mm screw 6.0mm bind nut 7 Nose x Main x 3 6 x30mm screw 8 3 3mm collar 3mm collar 9 Exhaust pipe Vertical Tail Wing Horizontal Tail Wing 5 30x5x3mm plywood 30 Foam Glue Foam glue Ducted Fan Unit Decal Tools Required Epoxy Glue Scissors Screw driver Sharp Hobby Knife attery required Li-Po atteries (Motor) wl Double-sided Tape Solder --size atteries (Transmitter) Needle Nose Pliers 8mm ox Driver Solder Iron (80W above)
Horizontal Tail Optional servo extension cable required for the connection of the elevator servos to receiver. Elevator Throttle attery pcs required Optional extension cable required for the connection of the ES.. Single cable (Throttle) Fuselage pc required. Silicone attery cable (No. WG or WG) pc required To ES Throttle To ES attery plug FLYFLY HOY Elevator 65mm opyright 009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
3 Fuselage Nose Gear D Note : Diagram included the optional air retract system. Please refer to the retract system instruction for the installation. Don t mix up the parts of left and right. The letter marked on the plywood. ir Retract system FLYFLY HOY opyright 009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
5 6 Fuselage ileron Elevator Throttle attery ssembly Fan unit Optional ir valve (main gear) Optional extension cable required for the connection of the aileron servo.. Single cable (lieron) onnect to aileron servo pcs required onnect to main retract gear air cylinder (Optional) Note : Install the cable and air tube before glue the fuselage together with epoxy. FLYFLY HOY (a) Never operate the unit with loose items of clothing or equipment near to the intake area. (b) Never operate the unit held in your hands as personal injury, or damage to the unit may occur. (c) lways do a thorough inspection of the unit prior to any operational use. (d) lways think safety first. (e) Secure all the screws. If any screws loose while rotating and the serious injury may occur. aution : s proper use of the fan unit is out of the influence of the manufacturer, the operation of the fan unit is on owners risk! This is not a toy! The unit should only be operated by childs of years and supervised by an adult. opyright 009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
7 8 Fan & ES Wing construction ES FLYFLY HOY opyright 009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
9 0 Wing construction Fin construction mm Nut x00mm rod 3 x 5 mm Linkage Stopper FLYFLY HOY opyright 009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com
65mm 7 mm djustment = = djustment 8 mm Never fly before checking the G s required position. Reposition the receiver and battery to obtain the correct G s location. ILERON ELEVTOR FLYFLY HOY 7 mm NEVER fly the model without well balancing. 50mm 5 mm 5 mm 5 mm 5 mm opyright 009 Fly Fly Hobby Designed and Manufactured by : Fly Fly Hobby Mfg. http://www.flyflyhobby.com