Parts Manual for REAR ENGINE RIDER EUROPEAN SERIES 22 MODELS E2822BE E2822BE E1522KVE CONTENTS DESCRIPTION PAGE(S) DESCRIPTION PAGE(S) WHEELS, TIRES...2, DRIVE DISC ASSEMBLY... 22 FRONT END, STEERING...4, 5 FUEL TANK & OPERATORS SEAT... 2 MAIN CASE..., ENGINE & EXHAUST MUFFLER... 24 DIFFERENTIAL, R.H. FENDER...8, 9 THROTTLE CONTROLS... 25 CHAIN CASE ASSEMBLY, L.H. FENDER..., 11 DECALS... 2-29 SMOOTH CLUTCH ASSEMBLY..., 1 ELECTRICAL SYSTEMS (Briggs)... 0, 1 CUTTING DECKS, DEFLECTORS...14, 15 ELECTRICAL SYSTEMS (Kohler)... 2, RAILS, LIFT ARMS, CAM LIFT...1, 1 WIRING SCHEMATICS... 4, 5 BLADE STOP PEDALS...18 ACCESSORIES & ATTACHMENTS... SPINDLE ASSEMBLY...19 HARDWARE BAGS... BELTS, BRAKES, INTERLOCK...20, 21 COPYRIGHT 2002 SNAPPER INC. ALL RIGHTS RESERVED (Rev. 1, 0/0/02) MANUAL No. 09
WHEELS - FRONT 1 ASSEMBLY 5 2 9 4 4 1 5-894 ASSEMBLY, Front Tire & Rim (Complete) (Includes Items 2,, 4, 5 & ) 2-5 TIRE, 11 x 4.00-4 (Kenda) 1-14 RIM (For 4./.50 x 4 Tire) 4 1-180 BEARING, Ball 5 1-224 VALVE, Air (Snap-in) 1-49 FITTING Lube 1-095 WASHER, /4 I.D. 8 1-22 CAP, Hub 9 1-2 SEAL, Felt -8 CAP, Dust 11 9-151 PIN, Cotter 5/2 x 1" (2) 1-0821 TUBE, Inner (For 4./.50 x 4 Tire) 11 8 MANUAL No. 09 2 R. E. RIDER (EURO)
8 2 WHEELS - REAR 5 15 9 1 14 11 1 1 ASSEMBLY 4 1 5-9851 ASSEMBLY, Rear Tire & Rim (Includes Items 2B, B & 4) (" Models) 2-584 TIRE, 1-.50 x 8 (" Models) 1-14 RIM, Extra Wide, (For 1/.50 x 8 Tire) (" Models) 4 1-224 VALVE, Air (Snap-in) 5 1-22 CLAMP, Right Hand (8, & 1 HP) -- 1-4542 CLAMP, Right Hand (, 14 & 15 HP) 9-1502 BOLT, 1/2-20 x /4" Lug () -12 BOOT, Right Hand (8 & HP) 8 1-181 SEAL, Oil 9 4-04 HUB, Rear Wheel R. H. (Weldment) 2-895 CAP, Hub 11 2-522 CAP, Hub (Left Hand) 4-044 HUB, Rear Wheel L.H. (Weldment) 1 1-01 NUT, 5/1-24 Hex Center Lock 14 1-5 BOLT, 5/1-24 x 1-5/8" Tapered (Left Hand) 15 1-1 BOLT, 5/1-24 x 2" Tapered (Right Hand) R. E. RIDER (EURO) MANUAL No. 09
FRONT END, STEERING 2 1 8 45 9 4 22 24 2 2 5 19 20 5 29 1 18 21 2 4 8 28 2 11 20 41 9 1 1 40 25 1 0 15 1 14 0 1 MANUAL No. 09 4 R. E. RIDER (EURO)
FRONT END, STEERING 42 4 44 1 5-800 STEERING WHEEL (for 5/8 shaft) (includes item 2) 2 2-81 LOGO, Steering Wheel 1-82 PIN, 1/4" x 1-1/2" Roll 4-824 LATCH, Parking Brake 5 2-2449 CABLE, Clutch/Brake(54.2 ) (for 28 & 0 Decks) -- -411 CABLE, Clutch (55 long) (for & 42 Decks) 9-02 WASHER, /8 Flat (2) 1-1815 PAD, Clutch/Brake Pedal 8 1-094 BUSHING, Nylon 9 4-888 PEDAL, Clutch/Brake (weldment) 1-098 BEARING, Nylon (4) 11 4-22 SHAFT, Steering (weldment) 1-21 BUSHING, Tie-Rod (4) 1 1-02 TIE-ROD, Left Hand (.41 long) -- 1-2541 TIE-ROD, Left Hand (9.91 long) 14 4-18 KING-PIN Weldment, Left Hand 15 1-29 TIE-ROD, R. H. (.41 long) -- 1-2540 TIE-ROD, R. H. (9.91 long) 1 4-188 KING-PIN, Weldment Right Hand 1 5-8040 WELDMENT, Front Axle, Narrow (28 & 0 Deck) -- 5-919 WELDMENT, Front Axle, Wide ( Deck) 18 1-4049 FOOT PAD, Short (2) -- 1-4048 FOOT PAD, Long (2) 19 1-5444 SPRING, Parking Brake 20 9-018 WASHER, 21/2 Dia. (2) 21 4-158 BUSHING, Nylon (2) 22 1-114 PIN, Hair 2 2- FOAM COVER, Steering Shaft 24 9-029 PIN, /1 x 1" Cotter 25 9-1514 WASHER, /8 Flat (2) 2 1-28 PIN, 1/8 Hair 2 2-2881 SPACER, 1/2" (5) 28 1-0 RING, 1/2 External Retaining (Heavy Duty) 29 1-04 RING, /4 Ext. Retaining (2) 0 9-05 PIN, 1/8 x /4" Cotter (2) 1 1-095 WASHER, 5/8 Flat () 2 2-1 COVER, Steering Shaft 2-895 SPACER, Pivot 4 2-82 STUD, Shoulder (/8-24 Thread) 5 9-0854 NUT, /8-24 Hex Nyloc -248 CABLE, Brake (29 long) -414 CONNECTOR, Cable (2) 8 9-1495 SCREW, 1/4-20 x /4", Gr. 5 9 9-02 NUT, 1/4-20 Hex Center Lock 40 9-05 PIN, /1" x 1-1/2" Cotter 41 9-04 PIN, 5/2 x 1 Cotter (2) 42-450 HOLDER, Wire- Bottle 4 9-091 SCREW, #-24 x 1/2 Hex Washer Self-Tap (2) 44-451 BOTTLE, Water 45-4599 PLATE, Thrust R. E. RIDER (EURO) 5 MANUAL No. 09
MAIN CASE 19 9 8 49 5 50 2B 1 21 52 * 5 1 50 * 50 51 5 50 1 5 48 4 4 22 42 2 5 CONNECTS TO ITEM 15 ON PAGE 9 4B 50 5 0 1 5 11 4A 5 50 1 4 2A 29 8 9 9 8 21 19 * NOTE: The heads of these fasteners are located underneath the main case. 29 29 2 29 MANUAL No. 09 R. E. RIDER (EURO)
2 29 SPRING (2-292) PART OF ITEM 1 MAIN CASE 20 14 18 24 25 4 2 1 41 5 50 40 45 44 4 1 2 28 15 1 5-8044 WELDMENT, Main Case -- 5-9202* WELDMENT, Main Case 2A -098 BUMPER, Rear (2) 2B - BUMPER (1-piece) ( Deck) -285 FENDER, Left Hand 4A -419* GUIDE, Belt 4B 1-5 GUIDE, Belt 5 4-189 BRACKET, Drive Support 9-0595 BOLT, 5/1-18 X /4" Hex Flange Lock, Grade 5 (2) 1-015 CAP, Bumper (2) 8 9-0585 NUT, 5/1-18 Hex Fl. Lock () 9 1-099 NUT, 5/1-24 Hex Flange Lock 2- LINK, Shift (Long) 11 4-184 ARM, Shift -99 BRACE, Cross 1 1-18 LINK, Shift (Short) 14 9-019 NUT, 5/1-18 Hex, Gr. 5 or B 15 4-0598 ARM, Shift Handle (weldment) 1 1-054 SPRING, Shift Handle 1 5-8 ASSEMBLY, Shift Detent (Incl. Spring, part no. 2-292) 18 5-92 HANDLE, Shift (weldment) 19 9-150 HAIRPIN, /2 X 1-1/2" (2) 20 2-5 GRIP, Shift Handle 21-4299 WING, Rear (2) 22 2-2509 BUSHING, Pilot 2-5 BRACKET, Switch 24 9-00 PIN, /2 x /4" Cotter 25 2-914 PIN, 1/4 x 1-/4" Tapered Clevis 2 1-9245 BUSHING, Nylon 2 - WASHER, Thrust (2) 28 1-924 BUSHING, Nylon (2) 29 9-01 SCREW, 5/1-18 x 5/8" Self Tap (14) 0 9-0981 SCREW, #-2 x 1/4" Hex Washer Self-Tap (2) 1 9-9 WASHER, 5/1" Flat (4) 2 1-252 CLIP, Wire 9-091 WASHER, 5/1 Internal Tooth Lock 4 9-0484 SCREW, 5/1-18 x 1-1/2" (4) 5 9-151 SCREW, 5/1-24 x 1-1/2" Hex Head Cap, Grade 5 (4) 1-191 RETAINER, 5/1 Bolt (4) 9-020 SCREW, 5/1-18 x /4" Cap 8 9-09 SCREW, 5/1-18 X /4" Hex Self-Tap (4) 9 2-8200 SWIVEL (2) 40 2-8989 COVER, Switch -- -28 COVER, Solenoid (Kohler) 41 2-8990 COVER, Battery 42 9-2 FASTENER, 1/4 Ratchet () 4 1-51 BOLT, 5/1-18 Shoulder 44-289 LEVER, Over-Ride 45 9-1595 WASHER, /1 Flat 4 9-98 NUT, 5/1-18 Nyloc 4 2-248 OIL DRAIN, Short 48 2-92 ASSEMBLY, Oil Valve 49-4190 PLATE, Engine (Kohler engine) 50 9-115 WASHER, 5/1 Split Lock (8) 51-92 BOLT, M8-1.25 x 25mm, Self- Tap (Kohler) 52 9-028 SCREW, 5/1-24 x 1 Gr. 5 (4) 5 9-9 NUT, 5/1-24 Hex, Grade 5 (8) *E1522KVE Model only R. E. RIDER (EURO) MANUAL No. 09
DIFFERENTIAL, R. H. FENDER 25 24 1 2 2A 5 2 4 4 2 22 9 2 21 8 2 11 1 28 14 28 2 15 29 0 1 20 1 5 19 18 1 1 MANUAL No. 09 8 R. E. RIDER (EURO)
DIFFERENTIAL, R. H. FENDER 1 1-4401 COLLAR, Lock (Includes P.N. 9-0201 Set screw) 2 1-8822 BALL BEARING, Axle (R. H. Fender) ( Models 1, 14, 15 HP) 2A 1-229 BEARING, Axle (R. H. Fender) (25 & 28 Models 8, & 1HP) 1-099 NUT, 5/1-24 Hex Flange Lock 4-9 WASHER, Thrust 5-80 PLATE, Differential 2-2115 SPACER, Pinion (4) 2-1 GEARS, Differential Pinion 8 1-2 WASHER, Thrust 9 5-1584 ASSEMBLY, Drive Hex Tube 1-0988 WASHER, Hex Nylon Splash 11 1-094 GEAR, 11 Teeth- Pitch 1-0941 CHAIN, 4 Pitch (#5) 1 2-19 SPROCKET 14 1-095 RING, Retaining 15 2-18 SPACER 1 1-22 CLAMP, Boot (2) 1 1-08 BOOT, Oil Seal 18 1-24 PLUG, Oil Fill & Check 19-29 CASE, Transmission 20 2-82 GASKET, Transmission Case 21-95 FENDER, Right Hand ( Ball Bearing Differential Models) (2.498 hole) -- -280 FENDER, Right Hand (25 & 28 Bushing Differential Models) (1.2 hole) 22 2-1158 GEAR, Teeth- Pitch 2 4- AXLE, Long (Includes Gear) (Use Only With Short Axle P.N. 5-98) 24-441 SPACER 25 5-98 AXLE, Short (Includes Gear) (Use Only With Long Axle P.N. 4-) 2 1-2 SCREW, 5/1-24 x 1-5/8" Hex Cap Special Lock (4) 2 1-115 O-RING, 5/1 (2) 28 1-182 WASHER, Belleville (2) 29 9-095 WASHER, 5/1 External Tooth Lock 0 9-0188 WASHER, 5/1 Flat 1 1-42 BOLT, 5/1-24 x 2-5/8" Idler 2 9-01 SCREW, 5/1-18 x 5/8" Self-Tapping (11) 9-02 SCREW, 1/4-20 x 5/8" Self-Tapping (1) 4-2 SPACER, Short Axle 5-1 GREASE, Transmission (24 oz. Required) -- -0411 KIT, Differential (Includes items 2A & -280 Fender) -- -02 KIT, Differential (Includes items 2 & -95 Fender) R. E. RIDER (EURO) MANUAL No. 09 9
CHAIN CASE, L. H. FENDER 14 2 15 1 5 28 1 ASSEMBLY 5 9 1 8 1 28 9 4 11 22 19 2 0 20 1 2 25 24 22 29 2 21 2 18 MANUAL No. 09 R. E. RIDER (EURO)
CHAIN CASE, L. H. FENDER 1 5-28 ASSEMBLY, Chain Case (Includes Items 2 Thru 1,15,1, & 1 Thru ) 2 4-11 CASE, Sprocket 2-81 GASKET, Case Cover 4 1-11 WASHER, Belleville (2) 5 1-05 BEARING, Ball (2) 1-89 SPROCKET & SHAFT 1-014 KEY, 1/8 x 5/8" Woodruff 8-98 COVER, Chain Case 9 1-0942 BEARING, Needle (2) 1-8 WASHER, Nylon Thrust (2) 11 4-055 HUB & SPROCKET 1-0941 CHAIN 1 9-00 SCREW, #-24 x 5/8" Hex Washer Self-Tap () 14 1-24 PLUG, Oil Fill & Check 15 2-285 ROLLER 1 1-0 RING, 1/2 External Retaining (Heavy Duty) 1-285 FENDER, Left Hand (25 & 28 Models) (1.28 I. D. hole) -- -958 FENDER, Left Hand ( Models) (1.44 I. D. hole) 18 1-425 COLLAR, Lock (Includes P.N. 9-0 Set Screw, 1/4-20 x 1/4") (Used with ball bearing, item 2, only) 19 5-0918 BEARING, Left Hand Fender (Includes Item 20) (25 & 28 Models, 8,, 1 HP) 20 1-24 FITTING, Lube 21 1-0 ROD, Cross-Tie 22 1-22 CLAMP, Boot (2) 2 1-084 BOOT, Oil Seal 24 1-1 WASHER, Thrust Nylon 25 1-2 WASHER, Thrust 2 9-1505 NUT, 5/8-18 Hex Nyloc 2 1-099 NUT, 5/1-24 Hex Flange Lock 28 1-920 O-RING (2) 29 2-44 SPACER 0 1-221 WASHER, Shim (As Required) 1 2-981 WASHER, Shim () 2 1-424 BALL BEARING, Left Hand Fender ( Models) -- 5-1451 ASSEMBLY, Left Hand Fender (Includes Fender P.N. -958 & Bearing P.N. 1-424) ( Models, 15 HP) -1 GREASE, Transmission (Use 2 oz. maximum) NOTE: See Pages & 1 For Illustration Of Brake Lever Assembly & Related Parts. R. E. RIDER (EURO) MANUAL No. 09 11
SMOOTH CLUTCH ASSEMBLY 14 0 2 2 29 1 1 2 2 25 29 24 15 19 28 1 4 1 5 11 1 21 18 8 22 2 4 1 1 21 9 20 See page, Item 40 18 MANUAL No. 09 R. E. RIDER (EURO)
SMOOTH CLUTCH ASSEMBLY NOTE: Brake Return Replacement Kit (-119) is made up of items 11 and 1. 1 5-114 ASSEMBLY, Smooth Clutch (Includes Items 2 thru ) 2 5-424 HUB, Driven Disc (assembly) 5- DISC, Driven (rubber tire bonded to rim) 4 1-452 WASHER, Thrust 5-21 PLATE, Drive Disc 9-0585 NUT, 5/1-18 Hex Flange Lock (4) 5-249 ASSEMBLY, Brake Lever (Includes Brake Lining & Rivet) 8 1-21 RING, /8 External Retaining 9 9-00 NUT, 1/4-28 Hex Top Lock 9-94 WASHER, 1/4 Flat 11-259 SPACER 9-1504 SCREW, 1/4-28 x 1" Hex Head Cap, Grade 5 (washer face) 1-240 SPRING, Brake Return 14 1-885 SPRING, Clutch Brake 15 4- LIFT, Yoke 1 1-48 BEARING, Yoke (2) 1 1-01 NUT, 5/1-24 Hex Center Lock (2) 18 9-028 SCREW, 5/1-24 x 1" Hex Head Cap, Grade 5 (2) 19 9-1198 SCREW, /8-1 x 5/8" Hex Washer Self-Tap 20-291 COLLAR, Yoke 21 1-1 WASHER, 5/1 Flat (2) 22 - ARM, Yoke 2 9-059 SCREW, 1/4-20 x 1/2" Hex Washer Self-Tap (2) 24 1-544 STUD (/8-24 thread) 25 9-090 WASHER, /8 Internal Tooth 2 9-10 NUT, /8-24 Hex, Grade 5 or B 2 4-190 BRACKET, Slide 28 9-00 PIN, /2 x /4 Cotter 29 1-4 SLIDE HALF (2) 0 1-44 BOLT, 5/1-18 Shoulder 1 9-018 WASHER, 5/1 Split Lock 2 9-019 NUT, 5/1-18 Hex, Grade 5 or B 9-02 WASHER, /8 SAE Flat (2) 4 5-908 ASSEMBLY, Leaf Spring R. E. RIDER (EURO) MANUAL No. 09 1
CUTTING DECKS, DEFLECTORS 1 24 1 0 5 28 29 4 2 14 SILHOUETTE OF RAILS & LIFT ARMS ASSEMBLY (See Pages 1 & 1) 2 25 5 9 4 8 1 2 2 22 9 15 21 11 22 1 21 19 18 1 8 2 20 MANUAL No. 09 R. E. RIDER (EURO) 14
CUTTING DECKS, DEFLECTORS 1-44 COVER, Spindle 2-190 DECK, 28 Replacement (Painted deck with decals) -- -192 DECK, Replacement (Painted deck with decals) 5-8 DEFLECTOR, Discharge (28" & " Deck) (Includes Items 4, 5,, & ) 4 2-2841 DECAL, DANGER (Cut Finger) 5-80 HINGE, Deflector 1-41 SPRING, Hinge 2-24 PIN, Hinge 8 9-0 NUT, 5/1-18 Hex Flange Lock 9 9-058 NUT, 1/4-20 Hex Flange Lock 2-48 NUT, Push (2) 11 9-0 BOLT, /8-1 x /4 Hex Flange Lock () 9-15 SCREW, 1/4-20 x -1/2 Hex Washer Self-Tap, Gr. 5 (2) 1 9-9 WASHER, 5/1 Flat (2) 14 9-0584 BOLT, 1/4-20 x 1/2 Hex Flange Lock 15-0480 KIT, Air Lift (28 & " Models) (Includes 1 Thru 19) 1-2 AIR-LIFT (2) (" Models) 1 9-0228 SCREW, 5/1-24 x 11/1" Machine () 18 9-091 WASHER, 5/1-24 Internal Tooth Lock () 19 9-022 NUT, 5/1-24 Hex () 20 9-092 SCREW, 1/2-20 x 1" Hex Head Cap, Grade 5 (2) 21 9-0509 WASHER, 1/2 Internal Tooth Lock (2) 22 9-0559 NUT, 1/2-20 Hex Jam (2) 2 9-1508 BOLT, 5/1-18 x /4" Short Neck Carriage, Grade 5 (2) 24 9-1 SCREW, 1/4-20 x 5/8" Hex Self-Tap w/ Captured Washer (4) 25 9-15 BOLT, 5/1-18 x 1/2" Hex Flange Lock () 2 1-98 COVER, 28" Mulcher -- 1-984 COVER, " Mulcher 2 9-01 NUT, /18-1 Hex Flange Lock (9) 28 9-1518 NUT, /8-24 Hex Nyloc () 29 9-152 SCREW, 8-24 x -/4 Hex Head Cap, Grade 5 () 0 1-9190 WHEEL, Gage () 1 1-522 SPACER () 2-50 BRACKET, Gage Wheel (Front) -51 BRACKET, Gage Wheel (Rear) (2) 4 9-01 BOLT, 5/1-18 x 1/2" Short Neck Carriage, Grade 5 () 5 9-0 NUT, 5/1-18 Hex Flange Lock (8) 9-0492 NUT, 5/1-18 Wing (2) 1-980 BLADE, 28" Mulcher -- 1-982 BLADE, Mulcher 8 1-9515 28" BLADE -- 1-952 " BLADE 9 2-45 BLADE, Ninja, 28 -- 2-441 BLADE, Ninja, R. E. RIDER (EURO) MANUAL No. 09 15
RAILS, LIFT ARMS, CAM LIFT 1 1 2 2 9 11 5 5 2 24 1 8 14 4 25 40 8 2 15 18 1 14 22 28 20 19 1 9 1 0 29 2 28 2 21 2 4 CABLE, NO REVERSE IN MOW (SEE PAGE 20, ITEM 11) MANUAL No. 09 1 R. E. RIDER (EURO)
RAILS, LIFT ARMS, CAM LIFT 1 9-150 HAIRPIN, /2 X 1-1/2 (2) 2 2-8200 SWIVEL (2) 2-828 HOOK, Chain (2) 4 9-022 NUT, 5/1-24 Hex (2) 5 9-0854 NUT, /8-24 Hex Nyloc 9-02 WASHER, /8 Flat -421 PIVOT, Leveling 8 5-924 ARM, Rear Lift (weldment) 9 9-048 SCREW, /8-24 X 1-/4 Hex Head Cap Grade 5-200 WASHER, 1/2 Flat (2) 11 4-155 LEVER, Height of Cut 9-0289 NUT, /8-24 Hex Center Lock 1 4-159 SPRING, Lever 14 1-208 RING, Blue (2) 15-1855 GUIDE, Belt 1 4-1 SPRING, Assist (2) 1-188 BRACE, Top 18 1-2 ROD, Leveling 19 9-01 SCREW, 5/1-18 x 5/8" Self-Tap 20 5-899 ASSEMBLY, Clutch Plate 21 4-848 RAIL, Deck Lift, Right Hand 22-29 RAIL, Deck Lift, Left Hand 2 4-15 DETENT, Height Adjust 24 9-024 SCREW, /8-1 x 1" Hex Washer Self-Tap (2) 25 4-21 DETENT, Spacer 2 9-1198 SCREW, /8-1 x 5/8" Hex Washer Self-Tap () 2 2-420 GRIP, Height Adjustment Lever 28 1-20 RING, Red (2) 29-299 ARM, Front Lift 0 5-8041 ARM, Front Lift (Weldment) 1 9-05 PIN, 1/8 x /4" Cotter 2 2-21 ROD, Support (Front Lift Arm to Front End) 1-84 SNAP RING, /1 4 9-0858 SCREW, 5/1-18 X 1/2 Hex Washer Self-Tap (2) 5-1920 SPACER, Deck Lift (2) 9-2051 BOLT, #-24 x 1 Flat Head Square Neck 9-90 NUT, #-24 Hex Nyloc 8-224 ANCHOR 9 9-02 SCREW, 5/1-24 x /4 Hex Head Cap, Grade 5 (2) 40 9-091 WASHER, 5/1 Internal Tooth Lock (2) R. E. RIDER (EURO) MANUAL No. 09 1
BLADE STOP PEDALS 2 9 11 1 1 8 5 4 1-2 PEDAL, Blade Stop Control 2-59 SPRING, Latching 1-5448 SPRING, Pedal 4 1-5495 BOLT, /8-24 Shoulder, Grade 5 5 1-544 BOLT, /8-24 x 9/1" Shoulder 1-20 WASHER, Cone 1/2 I. D. 9-0155 NUT, /8-24 Hex, Grade B 8 9-0250 WASHER, 1/2 Flat (2) 9 9-0289 NUT, /8-24 Hex Center Lock 9-1584 NUT, 1/4-20 Hex Flange Lock, Grade 5 11-21 CABLE, No Reverse In Mow -21 CLIP, Cable 1 9-1 BOLT, 1/4-20 x /4 Square Neck Carriage, Grade 5 MANUAL No. 09 R. E. RIDER (EURO) 18
1 ASSEMBLY SPINDLE 2 5 NOTE: Spindle housing assembly, Part no. 5-09 includes Items 4 and 5. 4 8 1 9 1 1 5-451 ASSEMBLY, Spindle Housing (Includes Items 2 Thru 1) 2 1-2491 RING, 1.85 Internal Retaining (2) 1-1 BEARING, Spindle (2) 4 4-040 WELDMENT, Spindle Housing 5 1-081 FITTING, Lube (for /1 diameter hole) 4-485 SPINDLE, Rider (.2 overall length) 1-095 WASHER, /4 Shim 8 1-440 WASHER, Spindle 9-51 HOLDER, Blade 4-482 SPACER, Blade Centering 11 9-05 NUT, 5/8-18 Hex Center Lock 9-0491 SCREW, 1/2-20 x 1-1/4 Hex Head Cap, Grade 5 (2) 1 9-199 NUT, 1/2-20 Hex Jam (2) 11 R. E. RIDER (EURO) MANUAL No. 09 19
BELTS, BRAKES, INTERLOCK 2 1 18 4 5 19 8 24 8 9 5 2 24 0 * 29 28 2 2 25 22 21 14 20 14 19 11 1 15 24 1 9 1 2 8 14 1 * SEE PAGE 1, ITEM 8 4 1 MANUAL No. 09 20 R. E. RIDER (EURO)
BELTS, BRAKES, INTERLOCK 1 4-844* BELT, Drive, ( Deck) (.5 AA Section) -- 2-2252* BELT, Drive (28 & 0 Deck) (2.5 AA Section) 2-44 NUT, /4-1 Hex Jam, Grade 8-202 WASHER, 49/4 I.D. x 1-1/2 O.D. Flat (2) 4 1-881 PULLEY, Spindle 5 1-5290 HUB, Pulley 9-99 NUT, /8-1 Nyloc (2) 2-924 PULLEY, 4 Idler (2) 8 9-149 SCREW, /8-1 x 1-1/2 Hex Head Cap, Grade 5 (2) 9-528 BRACKET, Fixed Idler ( Models Only) -52 BRACE, Fixed Idler Bracket ( Models Only) 11 9-0858 SCREW, 5/1-18 x 1/2 Hex Washer Self-Tap (5) 4-5 HANDLE, Blade Engage (Flip) 1 1-040 RING, 2 External Retaining (2) 14 9-00 PIN, /2 x /4 Cotter () 15-521 SPRING, Extension, 4 x 1/2 Diameter 1 4-8 ARM, Idler (weldment) 1 1-414 SPACER 18 4-84 GRIP, Handle 19 9-1514 WASHER, /8 Flat (2) 20-58 DRUM, Brake 21 1-404 PIN, 1/4 x 1-5/8 Clevis 22-4852 BAND, Brake 2 9-02 WASHER, /8 Flat (2) 24 9-0055 WASHER, 1/4 Flat (4) 25 4- EYE-BOLT, 1/4-20 x 4 2 4-48 SPRING, Flip Handle 2 9-194 PIN, /1 x 1 Clevis 28 5-9254 HANDLE, Blade Lever (ON-OFF) (weldment) 29 1-418 SPRING, Blade Handle 0 1-2055 ROD, Idler 1 9-0299 SCREW, #-2 x 1 Hex Washer Self-Tap 2 1-8524 SWITCH, Deck Interlock (NO) -8021 MOUNT, Handle/Switch 4 9-02 SCREW, 1/4-20 x 5/8 Hex Washer Self-Tap (2) 5 9-0555 PIN, /2 x 1/2 Cotter 9-01 NUT, 1/4-20 Hex Top Lock 1-44 BUSHING 8 4-82 SPRING 9-2111 RESTRICTOR, Belt * NOTE: Belt part numbers appear on belts. R. E. RIDER (EURO) MANUAL No. 09 21
DRIVE DISC ASSEMBLY 1 2 1-418 WELDMENT, 5.25 O.D. Drive Disc (" Models) - -258 WELDMENT, 5.5 O.D. Drive Disc (28, 0 & 42 Models) 2 9-012 SCREW, /8-1 x /8 Set (2) 1-02 KEY, 1/4 Square x 2 MANUAL No. 09 R. E. RIDER (EURO) 22
FUEL TANK & OPERATORS SEAT 1 2 A 1 8 5 14 4 9 11 1 2-8595 SEAT, Operator (, 14.5 & 15HP Models) (shown) -- 2-850 SEAT, Operator (9 & HP Models) (not shown) 2 5-1905 ASSEMBLY, Fuel Tank (9 & HP Models) (Includes Item ) -- 5-245 ASSEMBY, Fuel Tank with Gauge (, 14.5 & 15HP Models) (Incl. Item A) 1-2515 CAP, Fuel Tank A 1-9 CAP, Fuel Tank (With Gauge) 4-22 HOSE, Fuel (8-1/2" Long) (Briggs & Stratton: 8HP thru 14HP) -- 1-29 HOSE, Fuel (-1/2 Long) (Kohler Only!) 5 1-459 FILTER, Fuel (In-Line) 1-2222 CLAMP, Fuel Line (4) - BRACKET, Fuel Tank (Rear) 8 9-1542 SCREW, 5/1-18 x 5/8" Pan Head Self-Tap (Torx #T-40) (2) 9 2-191 KNOB, Seat Adjusting (2) 1-849 SPACER, 5/1 (2) 11 2-450 VALVE, Fuel Shut-Off (Accessory) 9-8 BOLT, 5/1-18 x 1/2" Hex Flange Lock w/nylon Patch (2) 1 2-9211 SWITCH, Seat (Normally Closed) 14 -- HOSE, Fuel (-1/2 Long) R. E. RIDER (EURO) MANUAL No. 09 2
ENGINES & EXHAUST MUFFLER ENGINE H.P. START TYPE ENGINE MFGR. MFGR. MODEL MFGR. TYPE.0 ELECTRIC BRIGGS & STRATTON C.A.R.B. 28B0 112-E1.0 ELECTRIC BRIGGS & STRATTON C.A.R.B. 280 11-E1 15.0 ELECTRIC KOHLER CV15ST PS-41584 20 18 1 1 20 1 5 15 19 11 14 14 2 9 8 1 4 1 5-199 MUFFLER (B&S 9-1 HP) (Includes items 8 & 9) 2 9-020 SCREW, 5/1-18 x /4 (2) 9-1814 SCREW, 1/4-20x1-1/4 Hex 4 1-958 MUFFLER (Kohler 14/15 HP) 5 9-0052 WASHER, 1/4 Split Lock 1-849 SPACER (2) 9-5 NUT, 1/4-20 Hex Flange Lock 8 1-925 DEFLECTOR, Heat 9 2-02 SCREW #8-18x/8 Type AB 9-94 WASHER, 1/4 Flat 11 9-1495 SCREW, 1/4-20 x /4 Hex 2-45 GUARD, Muffler (Kohler) 1-54 BRACKET, Muffler Guard (Kohler) 14 9-59 SCREW, 1/4-20 x 1 Hex 15 9-1 SCREW, 1/4-20 x 5/8 Hex Head Self-Tap (2) 1 5-8580 BRACKET, Heat Shield 1 9-09 SCREW, 5/1-18 x 1 18 5-858 HEAT SHIELD 19 5-859 BRACKET, Heat Shield, Front 20 9-9 SCREW, 1/4-20 x /8 () MANUAL No. 09 24
THROTTLE CONTROL 2 4 1 1 2-251 CONTROL, Throttle (2. long) (Briggs Engines) -- -420 CONTROL, Throttle (4. long) (Kohler Engine) 2 9-059 SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap (2) -40 PLATE, Throttle Control 4 9-091 SCREW, #-24 x 1/2 Hex Washer Self-Tap (Torx) (2) R. E. RIDER (EURO) MANUAL No. 09 25
DECALS 1 EUROPEAN DECALS 5 2 4 8 9 1 2-2215 DECAL, Brake Operation (German) 2 2-221 DECAL, Brake Operation (French) 2-2218 DECAL, Brake Operation (Dutch) 4 2-2841 DECAL, WARNING 5-415 DECAL, European Noise Control -59 DECAL, SAFETY Instruction (German & French) 2-9 DECAL, European Community 8 2-4052 DECAL, Deflector (German & French) 9 2-9948 DECAL, Battery Storage DECALS (Continued On Next Page) MANUAL No. 09 2 R. E. RIDER (EURO)
EUROPEAN DECALS DECALS 11 1 14 15 1 1-594 DECAL, SAFETY Instruction (English & Dutch) 11 2-984 DECAL, DO NOT OPERATE! 2-8514 DECAL, Clutch/Brake 1 2-994 DECAL, Battery CAUTION 14 2-940 DECAL, Patent Numbers 15 2-989 DECAL, Deflector CAUTION (English & Dutch) 1 2-99 DECAL, 28 Inch (Hi-Vac) 1 2-2991 DECAL, Inch (Hi-Vac) DECALS (Continued On Next Page) R. E. RIDER (EURO) MANUAL No. 09 2
DECALS 19 20 18 21 22 2 18 2-980 DECAL, Back-Up Recoil ( Kohler Engine Models) 19 2-982 DECAL, OHV ( Kohler Engine Models) 20-191 DECAL, Snapper 21-201 DECAL, Brake Operation (Italian) 22-202 DECAL, Brake Operation (Spanish) * -4 DECAL, Year Of Manufacture (2001) 2 4-218 DECAL, Height of Cut MANUAL No. 09 DECALS (Continued On Next Page) 28 R. E. RIDER (EURO)
DECALS 24 25 2 2 28 29 1 0 24 2-911 DECAL, CAUTION, Fuel 25 2-9114 DECAL, CAUTION, Fuel Leakage (Dutch) 2 2-94 DECAL, CAUTION, Fuel Leakage (German) 2 2-945 DECAL, CAUTION, Fuel Leakage (French) 28-199 DECAL, CAUTION, Fuel Leakage (Italian) 29-200 DECAL, CAUTION, Fuel Leakage (Spanish) 0-20 DECAL, Safety Instructions (Spanish/Italian) 1-4480 DECAL, No Mow in Reverse 2 1-14 TAG, Caution 2 R. E. RIDER (EURO) MANUAL No. 09 29
ELECTRICAL SYSTEMS (For 8,, & 1 HP Briggs) TO ITEM 8 J I TO ITEM 2 TO ITEM 2 24 22 19 22 2 9 8 H G TO ITEM (D, E, F) TO ITEM (A) 24 TO ITEM 11 1 TO ITEM 4 20 L H 25 1 4 K L G. MAGNETO SHORTING BLOCK (See Inset on Page 1) 21 L 5 2 11 2 14 1 15 M L 18 H. ENGINE GROUND I. ALTERNATOR CHARGING WIRE 1 J. STARTER TERMINAL M TO ITEM 5 G K 1 MANUAL No. 09 R. E. RIDER (EURO) 0
ELECTRICAL SYSTEMS (For 8,, & 1 HP Briggs) 1-05 KIT, Volt Dry Charge Battery 2 1-881 SOLENOID 2-288 HARNESS, Starter Wiring (Briggs Engines) 4 1-929 HARNESS, Ignition Wiring (Briggs Engines) 5 1-18 HOLDER, Fuse (Includes Fuse) -- 1-19 FUSE ( AMP) 2-80 INTERLOCK Module (Briggs) 2-88 HARNESS (Deck Interlock Wiring) 8 1-8524 SWITCH, Deck Interlock (NO) 9 1-2444 COVER, Battery Cable 1-92 CABLE, Positive (1 Long, Red) 11 1-881 SWITCH, Ignition (Used With Electric Start) 9-0880 WASHER, 5/8 Internal Tooth Lock 1 1-548 NUT, 5/8-2 Hex 14 1-118 KEY, Switch (2) 15 9-059 SCREW, 1/4-20 x 1/2" Hex Washer Self-Tap () 1 2-288 SWITCH, Operator Presence Control (OPC) Traction (NC/NO) 1 9-15 NUT, 1/4-20 Hex, Grade 5 or B (5) 18 9-005 WASHER, 1/4 Internal Tooth Lock (2) 19 2-12 SCREW, 1/4-20 x 5/8" Hex Head Cap, Grade 5 (2) 20 2-802 CABLE, Negative (15 Long) 21 2-80 HARNESS, Operator Presence Control (OPC) Wire 22 1-2485 RETAINER, 1/4 Bolt (2) 2 1-2080 TIE, " Long Cable (2) 24 9-02 NUT, 1/4-20 Hex Center Lock (2) 25 1-4451 TIE, 2" Long Cable 2 2-9211 SWITCH, Seat (8,, & 1 HP Engines) (NC) R. E. RIDER (EURO) MANUAL No. 09 1
ELECTRICAL SYSTEMS (For 14 & 15 HP KOHLER) 8 TO ITEM 8 24 9 TO ITEM 2 25 TO ITEM 2 19 25 2 1 TO ITEM 4 H TO ITEM (D, E, F) TO ITEM (A) 1 G 24 TO ITEM 11 L I 2 J 4 1 L 5 11 14 H. ENGINE GROUND I. BATTERY GROUND (See Inset on Page ) 21 L 15 2 M L 18 22 J. STARTER TERMINAL K ENGINE MOUNTING PLATE M TO ITEM 5 K 1 2 MANUAL No. 09 R. E. RIDER (EURO) 2
ELECTRICAL SYSTEMS (For 14 & 15 HP KOHLER) 1-05 KIT, V Dry Charge Battery 2 1-881 SOLENOID 1-921 HARNESS, Starter Wiring (Kohler) 4 1-922 HARNESS, Ignition Wiring (Kohler) 5 1-18 HOLDER, Fuse (Includes Fuse) 1-19 FUSE ( AMP) 2-80 INTERLOCK Module (Briggs & Kohler) 2-88 HARNESS, (Deck Interlock Wiring) 8 1-8524 SWITCH, Deck Interlock (NO) 9 1-2444 COVER, Battery Cable 1-92 CABLE, Positive (Red) (1 Long) 11 1-881 SWITCH, Ignition 9-0880 WASHER, 5/8 Internal Tooth Lock 1 1-548 NUT, 5/8-2 Hex 14 1-118 KEY, Switch (2) 15 9-059 SCREW, 1/4-20 x 1/2" Hex Washer Self-Tap () 1 1-4451 TIE, 2" Long Cable 1 9-00 NUT, 1/4-20 Hex (4) 18 9-005 WASHER, 1/4 Internal Tooth Lock (2) 19 2-12 SCREW, 1/4-20 x 5/8" Hex Head Cap, Grade 5 (2) 20 2-802 CABLE, Negative (15 Long) 21 2-88 HARNESS, Operator Presence Control Wire 22 9-15 NUT, 1/4-20 Hex, Grade 5 or B 2 1-2080 TIE, " Long Cable (2) 24 9-02 NUT, 1/4-20 Hex Center Lock (2) 25 1-2485 RETAINER, 1/4 Bolt (2) 2 2-9211 SWITCH, Seat (NC) 2 2-288 SWITCH, Operator Presence Control (OPC) Traction (NC/NO) R. E. RIDER (EURO) MANUAL No. 09
WIRING SCHEMATICS WIRING SCHEMATIC FOR 8,, & 1 HP BRIGGS ENGINES MANUAL No. 09 4 R. E. RIDER (EURO)
WIRING SCHEMATICS WIRING SCHEMATIC FOR 14 & 15 HP KOHLER ENGINES R. E. RIDER (EURO) MANUAL No. 09 5
ACCESSORIES & ATTACHMENTS SNAPPER REAR ENGINE RIDER ACCESSORIES* PART NO. DESCRIPTION OF KIT MODELS USED ON -051... Wheel Weight (8 Wheels)...All Rear Engine Riders -09... Dump Cart...All Rear Engine Riders -0... Gage Wheel...All Deck Rear Engine Riders -0941... Single Bag Catcher...All 25 Deck Rear Engine Riders -094... Single Bag Catcher...All 28 & Deck Rear Engine Riders -094... Twin Bag Catcher...All 28 & Deck Rear Engine Riders -094... Bag-N-Wagon...All 28 & Deck Rear Engine Riders -0948... 28 Thatcherizer...All Series & Newer Riders -094... Wagon Cover...All 28 & Deck Rear Engine Riders -1190... Weight (Front)...All Series & Newer Riders -0959... Dozer Blade ( Blade)...All Rear Engine Riders -05... Tire Chains (Tires-1 x.50-8)...all Rear Engine Riders -05... Tire Chains (Tires-1 x 4.80-8)...All Rear Engine Riders -49... Ninja Recycling (Cover)...All 25 Deck Rear Engine Riders -5... Ninja Recycling (Cover)...All 28 Deck Rear Engine Riders -55... Ninja Recycling (Cover)...All Deck Rear Engine Riders -025... Drive Disc Puller...All RER Aluminum Drive Discs *For illustrated parts lists of kits see Manual #0084. MANUAL No. 09 R. E. RIDER (EURO)
HARDWARE BAGS LOCATION -- -182 HARDWARE BAG (includes items listed below) (models: E2822BE & E2822BE) 1 1-24 PLUG, Oil Fill & Check (2)... page 8, item 18 & page, item 14 2 1-21 BUSHING, Tie Rod page 5, item 1-849 SPACER, 21/4 (2)... page 2, item 4 1-82 PIN, 1/4 x 1-1/2 Roll... page 4, item 5 2- FOAM COVER, Steering Shaft... page 4, item 2-1 COVER, Steering Shaft... page 4, item 1 9-02 NUT, 1/4-20 Hex Center Lock (2)... pg. 0 & 2, item 24 8 9-8 BOLT, 5/1-18 x 1/2 Hex Flange Lock (2)... page 2, item 9 9-02 WASHER, /8 Flat... pages 5, 1, 1 & 21 9-029 PIN, /1 x 1 Cotter... page 5, item 24 11 9-151 PIN, 5/2 x 1 Cotter (2)... page 2, item 11 & page 5, item 28 2-9211 SEAT SWITCH (NC)... page 2, item 1 1 2-191 KNOB, Three-Prong (2)... page 2, item 9 14 2-895 SPACER, Pivot (2)... page 5, item 15 9-091 SCREW, #-24 x 1/2 Self-Tap (2)... pages 5 & 25 LOCATION -- -185 HARDWARE BAG (includes items listed below) (model: E1522KVE) 1 1-24 PLUG, Oil Fill & Check (2)... page 8, item 18 & page, item 14 2 1-849 SPACER, 21/4 (2)... page 2, item 1-82 PIN, 1/4 x 1-1/2 Roll... page 4, item 4 2- FOAM COVER, Steering Shaft... page 4, item 5 2-1 COVER, Steering Shaft... page 4, item 1 9-02 NUT, 1/4-20 Hex Center Lock (2)... pg. 0 & 2, item 24 9-8 BOLT, 5/1-18 x 1/2 Hex Flange Lock (2)... page 2, item 8 1- BUSHING, Tie Rod... page 5, item 9 9-02 WASHER, /8 Flat... pages 5, 1, 1 & 21 9-029 PIN, /1 x 1 Cotter... page 5, item 24 11 2-9211 SEAT SWITCH (NC)... page 2, item 1 2-191 KNOB, Three-Prong (2)... page 2, item 9 1 9-091 SCREW, #-24 x 1/2 Self-Tap (2)... pages 5 & 25 14 9-151 PIN, 5/2 x 1 Cotter (2)... page 2, item 11 & page 5, item 28 R. E. RIDER (EURO) MANUAL No. 09
NOTES 8
NOTES 9
Parts Manual for REAR ENGINE RIDER EUROPEAN SERIES 22 MODELS E2822BE E2822BE E1522KVE IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY. COPYRIGHT 2002 SNAPPER INC. ALL RIGHTS RESERVED MANUAL No. 09 (Rev. 1, 0/0/02) Printed in U.S.A. 40