COMPRESSOR SERVICE VALVES Table of Contents Selecting the Correct Service Valves 1. Determine Type of Fitting on Compressor Head: HEAD TYPES O Ring 3/4 x 7/8 Tube-O 1-14 Rotalock, or Flange 2. Determine Valve Needed: #8 Discharge (high side) #10 Suction (low side) 3. Determine Hose End Fitting Type: Beadlock Flare, or O Ring 4. Service Valve Port Locations and Type: R12 Port 1/4 (7/16-20 thread) R134a Port 13mm used on Suction (low side) R134a Port 16mm used on Discharge (high side) 5. Backseat Seat Type: Incorporates a valve which can be set at three different positions to control A/C system refrigerant flow. Open Mid-way, or Closed SERVICE VALVES SPECIFICATIONS CHART...332 VISUAL ILLUSTRATIONS SECTION...333 HEAD FITTING TYPES...331 RELATED ITEMS Adapters... 338 Assortments (caps, cores, retrofit)... 337 A-6 Manifolds, Universal... 335 Compressor Gasket Kits... 341 Compressor Shaft Keys... 341 Drier Port Adapters... 339 Pressure Relief Valves... 335 RetroFit Adapters / Fittings and Weld-on... 338 Schrader Valve Cores... 337 Service Caps... 336 Shaft Seal Kits... 340 330 2017 MEI Corporation
SERVICE VALVES COMPRESSOR HEAD FITTING TYPES T/CCI, YORK, BLISSFIELD/TECUMSEH STYLE Typical Examples: Typical Example: ROTALOCK Uses white teflon seal 1/2 (#8) x 5/8 (#10) FLANGE Uses paper gasket or square cut O Ring 1-14 TUBE-O RING Uses HNBR (green) O Ring #5576 #5673 seal kit #0015 TECH TIP 1-14 Tube-O Service Valves are interchangable, and can be used on both upright or rotary type compressors. ICE, SANDEN, SELTEC, TAMA Typical Examples: Typical Example: 3/4 x 7/8 O RING FITTING 1-14 TUBE-O RING FITTING #10 7/8-14 #8 3/4-16 1-14 1-14 Vertical Uses: (1) #8 and (1) #10 O Ring #8 Discharge use O Ring #0013 #10 Suction use O Ring #0015 Horizontal Vertical Uses: (2) #10 O Rings Discharge use O Ring #0015 Suction use O Ring #0015 2017 MEI Corporation 331
COMPRESSOR SERVICE VALVES Service Valve Specifications NOTE: Also refer to AEROQUIP section for E-Z CLIP service valve types. COMPRESSOR HOSE END HOSE END FTG. PORT PORT PORT FITTING TYPE FITTING TYPE FITTING SIZE PART# TYPE DESCRIPTION LOCATION NOTES ROTALOCK HEAD w/teflon SEAL - CCI / YORK - TECUMSEH / BLISSFIELD COMPRESSORS ONLY Rotalock O Ring #8 3/4 5449 R12 1/4 (7/16-20) Back Rotalock O Ring #10 7/8 5450 R12 1/4 (7/16-20) Back Rotalock O Ring #8 3/4 5511 R134a 16mm (high side) Back Rotalock O Ring #10 7/8 5512 R134a 13mm (low side) Back 1-14 TUBE-O RING Tube-O Ring Beadlock #8-4522S R134a 16mm (high side) on tube 45 Tube-O Ring Beadlock #10-4523S R134a 13mm (low side) on tube 45 Tube-O Ring Beadlock #8-4524S R134a 16mm (high side) on tube 90 Tube-O Ring Beadlock #10-4525S R134a 13mm (low side) on tube 90 Tube-O Ring Beadlock #8-5432A R134a Discharge Tube-O Ring Beadlock #8-5432, R R134a 16mm (high side) Back Tube-O Ring Beadlock #10-5433A R134a Suction Tube-O Ring Beadlock #10-5433 R134a 13mm (low side) Back Tube-O Ring Beadlock #12-5434 R134a 13mm (low side) Back Tube-O Ring O Ring #8 3/4 5435 w/o port Tube-O Ring O Ring #10 7/8 5436 w/o port Tube-O Ring O Ring #8 3/4 5418 R12 1/4 (7/16-20) Top Backseat Tube-O Ring O Ring #8 3/4 5521 (2) R12 1/4 (7/16-20) Top-Back Tube-O Ring O Ring #10 7/8 5522 (2) R12 1/4 (7/16-20) Top-Back Tube-O Ring O Ring #8 3/4 5513 R134a 16mm (high side) Back Tube-O Ring O Ring #10 7/8 5514 R134a 13mm (low side) Back Tube-O Ring O Ring #8 3/4 5517 R134a 16mm (high side) Top Backseat Tube-O Ring O Ring #10 7/8 5518 R134a 13mm (low side) Top Backseat Tube-O Ring Beadlock #14-5525SR R134a 3/4 x 7/8 O RING TYPE - SANDEN - SELTEC/VALEO COMPRESSORS (non-rotalock, non-tube-o) # 8 O RING O Ring #8 3/4 5523 R12 1/4 (7/16-20) Back #10 O RING O Ring #10 7/8 5524 R12 1/4 (7/16-20) Back # 8 O RING O Ring #8 3/4 5519 R134a 16mm (high side) Back #10 O RING O Ring #10 7/8 5520 R134a 13mm (low side) Back # 8 O RING O Ring #8 3/4 5528 R134a 16mm (high side) Top In-line Adapter #10 O RING O Ring #10 7/8 5529 R134a 13mm (low side) Top In-line Adapter #8 O Ring O Ring #8 3/4 5445 No Port 90 Adapter #10 O Ring O Ring #10 7/8 5446 No Port 90 Adapter #10 O Ring O Ring #10 7/8 5438 R134a 16mm (high side) Back TM31HD only #12 O Ring O Ring #12 1-1/16 5439 R134a 13mm (low side) Side TM31HD only DENSO COMPRESSORS PAD - 10PA15C O Ring #8 3/4 4222WK No Port fits on manifold #5835 PAD - 10PA15C O Ring #10 7/8 4223WK No Port fits on manifold #5835 PAD - 10S15C O Ring #8 3/4 5566D No Port fits on plate #5938 PAD - 10S15C O Ring #10 7/8 5566S No Port fits on plate #5938 PAD - 6E171 O Ring #10 3/4 5441 R12 1/4 (7/16-20) PAD - 6E171 O Ring #8 7/8 5442 w/o port with PRV PAD - 10PA17C O Ring #8 & #10 3/4-7/8 5437 R134a 13mm with PRV PAD - 10PA15C O Ring #8 & #10 3/4-7/8 5437R R134a w/o port with PRV PAD TYPE COMPRESSORS - SD7B10 #8 MIO MIO #8 4228S R134a Discharge #10 MIO MIO #10 4229S R134a Suction 332 2017 MEI Corporation
Service Valve Specifications SERVICE VALVES COMPRESSOR NOTE: Also refer to AEROQUIP section for E-Z CLIP service valve types. COMPRESSOR HOSE END HOSE END PORT PORT PORT FITTING TYPE FITTING TYPE FITTING SIZE PART# TYPE DESCRIPTION LOCATION NOTES GM/J.Deere/CAT/A6/S6 COMPRESSORS #8 O RING O Ring #8 3/4 5542C R134a 16mm on tube #10 O RING O Ring #10 7/8 5543C R134a 13mm on tube #8 O RING O Ring #8 3/4 5542MP R12 1/4 (7/16-20), 16mm on tube #10 O RING O Ring #10 7/8 5543MP R12 1/4 (7/16-20), 13mm on tube PAD O Ring #8 3/4 5542S No Port PAD O Ring #10 7/8 5543S No Port PAD O Ring #12 7/8 5544S No Port Service Valves Denso - 10PA15C Drillable Flange and Weldable Fitting Kit Must drill flange to mount and aluminum-weld fitting. (fits onto manifold of #5835) 4222WK #8 MIO Discharge Side Thread Size 3/4 16 4223WK #10 MIO Suction Side Thread Size 7/8 14 R134a Port 90 Beadlock STEEL #5473R #5835 R12 - Backseat O Ring Fitting 45 Port Angle SD7B10 Compressor Adapter Fitting PAD Type - 4228S #8 MIO Discharge 4229S #10 MIO Suction O RINGS PAD MIO SUCT...#0010...#0015 DISCH...#0116...#0013 Flange Compressor T/CCI (York Style) Standard Flow Ports Denso - 10S15C Pad Fitting (fits onto plate of #5938) Aluminum Std O ring 5566D #8 Discharge (uses #0162 o ring) 5566S #10 Suction (uses #0161 o ring) R134a Port Beadlock 4524S... std. 4524SR... Reduced Dia. #8 Beadlock Discharge w/16mm 4525S...std. 4525SR... Reduced Dia. #10 Beadlock Suction w/13mm 5418 #8 O Ring Discharge 5426 #10 MIO - Suction 13mm Port, Flange Type While Supplies Last 5432...Standard 5432R... Reduced Dia. #8 Beadlock Discharge w/16mm 5433...Standard 5433R... Reduced Dia. #10 Beadlock Suction w/13mm 5434...Standard 5434R... Reduced Dia. #12 Beadlock Suction w/13mm 5453R... Reduced Dia. #14 Beadlock Suction w/13mm R134a Port 45 Beadlock STEEL Beadlock w/o Port Tube-O Type T/CCI (York Style) Tecumseh, Sanden Compressors w/o Service Port Seltec TM31HD Compressor STD. Flow Ports 4522S...std. #8 Beadlock Discharge w/16mm 4523S...std. #10 Beadlock Suction w/13mm 5432A #8 Beadlock Discharge 5433A #10 Beadlock Suction 5525SR... Reduced Dia. #14 hose, Beadlock 5435 #8 MIO - Discharge 5436 #10 MIO - Suction 5438 Discharge - High Side #10 Hose Fitting 16mm Port Size uses #0115 o ring 2017 MEI Corporation 333
COMPRESSOR SERVICE VALVES Listed in ascending order by our part number (continued). Seltec TM31HD Compressor STD. Flow Ports Sanden, Seltec 90 O Ring Coupler Adapts to Male Insert O Ring w/o Port Rotalock Compressor R12 - Schrader O Ring Fitting Rotalock Compressor R134a Port O Ring Fitting (cap #5531) 5439 Suction - Low Side #12 Hose Fitting 13mm Port Size uses #0115 o ring 5444 #6 5/8-18 Female x 5/8-18 Male 5445 #8 3/4-16 Female x 3/4-16 Male 5446 #10 7/8-14 Female x 7/8-14 Male 5449 #8 O Ring Discharge 5450 #10 O Ring Suction 5511 #8 O Ring Discharge w/16mm 5512 #10 O Ring Suction w/13mm R134a Port O Ring Fitting R134a Port - Backseat O Ring Fitting O Ring Compressor R134a Port Adapter 90 O Ring Fitting R12 - Schrader O Ring Fitting (2 ports) (cap #5531) 5513 #8 O Ring Discharge w/16mm 5514 #10 O Ring Suction w/13mm O Ring #8, #10 R12 - Schrader (cap #5578) 5517 #8 O Ring Discharge w/16mm 5518 #10 O Ring Suction w/13mm O Ring Compressor Sanden, Seltec R134a Port Adapter (straight) TECH TIP: Use to add a R134a Service Port to a R12-R134a compressor conversions. 5519 #8 O Ring Discharge w/16mm 5520 #10 O Ring Suction w/13mm 5521 #8 O Ring Discharge 5522 #10 O Ring Suction (cap #5531) 5523 #8 O Ring - Discharge 5524 #10 O Ring - Suction (cap #5531) TECH TIP: Use to add a R134a Service Port to a R12-R134a compressor conversions. 5528 #8 O Ring Discharge w/16mm 5529 #10 O Ring Suction w/13mm 5540 Compressor Adapter Converts Tube-O to Rotalock (2 required per compressor) Rotalock Seal #5576 5541 Compressor Adapter Converts Rotalock to Tube-O (2 required per compressor) O ring #0015 A6/S6 Service Valve R134a Port STEEL (Caterpillar) #0121 O rings Suct/Disch A6/S6 Compressor Fitting STEEL (Caterpillar) #0121 O rings Suct/Disch R134a A6/S6 Compressor Fitting STEEL (Caterpillar) #0121 O rings Suct/Disch R134a A6/S6 Adapter Pad Fittings GM, CAT, J.Deere Std O ring #0121 O rings Suct/Disch R12 R12 5542C #8 w/16mm port 5543C #10 w/13mm port Caterpillar A6 Service Vlv 5542MP #8 w/16mm port and R12 switch port (side) 5543MP #10 w/13mm port and R12 switch port 5542S...#8 MIO (steel) 5543S...#10 MIO (steel) 5544S...#12 MIO (aluminum) GM A6, PAD Fittings Adapter 334 2017 MEI Corporation
Manifolds GM/HT6 Sealing Washer Style Manifold w/deep Insert Denso 10PA17C Manifold SERVICE VALVES COMPRESSOR Denso 10PA15C & 10PA17C Manifold Denso 10PA15C Manifold #10 #8 5209 Add-on Manifold Fits GMC Delphi compr w/sealing washer head (uses #0140 sealing washers). #8 MIO x #10 MIO (requires #4249GK bolt kit) 5437 10PA17C (J.DEERE) Top Manifold Discharge & Suction #8, #10 Female Fittings Fits compressors: #5830, #5832, #5833, #5838 5437B 10PA17C (J.DEERE) Compressor Manifold (aluminum) #8, #10 Female Fittings (uses #0164 gasket) Fits compressors: #5831, #5834, #5836, #5837 5437R 10PA15C (J.DEERE) Compressor Manifold, Female (alum) Manifold exits on right side of compressor (uses #0164 gasket) Fits compressor: #5835 OE# AL78780 Denso 6E171 Manifold Denso 6E171 Manifold #10 #12 5441 6E171 (J.DEERE) #10 Suction Manifold, R12 port, 7/16 thread. Fits compressors: #5845, #5849 Hold Down Kits 5442 6E171 (J.DEERE) #8 Discharge Manifold M12-1.00 HPRV (uses #50800 PRV) Fits compressors: #5831, #5849 #10 #8 5206 Universal Swivel Manifold #8 x #10 Male Insert O ring Fittings Aluminum; without ports Fits: Sanden, Seltec, A6 Compressors 5208 Universal Manifold #10 x #12 Male Insert O ring Fittings Aluminum; without ports Fits: Sanden, Seltec, A6 Compressors 5545S A6/S6 - Hold Down Bracket Kit GM / CAT / J.Deere Supplied with a standard and metric bolt. 5546S A6/S6 to Sanden Conversion GM / CAT / J.Deere Hold Down Bracket Kit (used with #5207) Compressor Pressure Relief Valves 5682M GM Compressors (Delphi) Brass, Metric M10-1.25 thread w/hnbr O ring. M10-1.25 Metric 5683 CCI/York Style,Tecumseh, and Ford FS6 Bleeds off excessive R12 pressure in excess of 400 p.s.i. 3/8-24 3/8-24 5685 (R12 & R134a) Universal Denso 10PA17C, Seltec, GM HT6 Bleeds off excessive refrigerant pressure in excess of 400 p.s.i. 5686 Sanden - Old Style Bleeds off at 500-600 p.s.i. 3/8-24 5686A Sanden - New Style Aluminum Low Profile w/hnbr O ring. 3/8-24 M10-1.5 Metric 5687 DENSO 10PA15C / 17C - Metric M10-1.5 thread w/o O ring. M12-1.0 Metric 50800 DENSO 6E171 only - Metric M12-1.00 thread HNBR 2017 MEI Corporation 335
COMPRESSOR SERVICE PARTS Service Caps 5531...1/4 5532...3/16 Plastic () 5578 Backseat Service Valve Cap Black Plastic () 8953 M9-1.0 Port Caps Off road applications Low Side - light blue () 8954 M10-1.25 Port Caps Off road applications High Side - light blue () 8956 Switch Port Caps M10-1.25 () R134a Service Caps 5533 5534 5587 5588 8957 Switch Port Caps M12-1.5 () Black Blue with L (Low) *Bridgeport Piedmont OEM R134a 13mm Port *Bridgeport Piedmont RetroFit 13mm Adapter *Refrigeration Sales R134a RetroFit 13mm Adapter Black Red with H (High) *Bridgeport Piedmont OEM R134a 16mm Port *Bridgeport Piedmont RetroFit 16mm Adapter *Refrigeration Sales R134a RetroFit 16mm Adapter Blue *Aeroquip OEM R134a 13mm Port *Aeroquip Piedmont RetroFit 13mm Adapter *Frig-C Low Side R134a RetroFit Adapter Red *Aeroquip OEM R134a 16mm Port *Aeroquip Piedmont RetroFit 16mm Adapter *Frig-C High Side R134a RetroFit Adapter 5574 5575 5579 5580 Blue with L (Low) *Bridgeport Piedmont OEM R134a 13mm JRA Port Red with H (High) *Bridgeport Piedmont OEM R134a 16mm JRA Port Black *Eaton OEM SSV High Flow R134a 13mm Port *Refrigeration Sales CCI Service Valve w/eaton SSV High Flow 13mm Port Black *Eaton OEM SSV High Flow R134a 16mm Port *Refrigeration Sales CCI Service Valve w/eaton SSV High Flow 16mm Port *Bridgeport Piedmont (Schrader Bridgeport) OEM ports are typically found on some GM and Ford Vehicles. *Eaton OEM ports are typically found on some heavy duty trucks and equipment and some Ford vehicles. *Aeroquip OEM ports are typically found on Chrysler, Ford heavy duty trucks, Navistar, John Deere, some GM & Ford vehicles, and numerous import vehicles. 336 2017 MEI Corporation
Assortments - Caps, Cores, and RetroFit Components SERVICE PARTS COMPRESSOR 8915 8916 8914 8955 8925 8926 5531 5574 5575 5580 5534 5579 (10 per) (2 per) (2 per) (2 per) (2 per) (2 per) Universal Standard Flow Valve Core R12 / R134a High Flow JRA Valve Core R134a GM High Flow Large Bore Valve Core R12 / R134a Volvo M8 High Flow Schrader Valve Core Eaton 13MM SSV High Flow Valve Core R134a Eaton 16MM SSV High Flow Valve Core R134a 1/4 Low Side 3/16 High Side 5532 (5 ea.) 13mm Hex Blue (5 ea.) 16mm Hex Red (5 ea.) 16mm Round Black (5 ea.) 16mm Hex Red (5 ea.) 13mm Round Blue (5 ea.) 13mm Round Black 5533 8938 R12/R134a Schrader Valve Core Kit 8977 Complete Charging Port Cap Kit for R12/R134a 8916 5552 (3 ea.) (2 ea.) 5531 (5 ea.) 1/4 Low Side 5574 (5 ea.) 13MM Round Blue 8915 8914 8919 (3 ea.) (1 ea.) 8978 R134a Valve Core Repair Assortment Kit 8984 Small Port Cap Kit 8916 5532 (5 ea.) 3/16 High Side (NSS) (NSS) 5563 (3 ea.) 5575 (5 ea.) 16MM Hex Red 5564 (3 ea.) 5565 (3 ea.) 5532 (NSS) 5533 5587 8915 8916 8914 5555 (5 ea.) (NSS) (NSS) 5534 5588 8986 Multi-Refrigerant Schrader & Port Cap Kit A full assortment of schrader valves and charging caps. 8914 8914 8915 8889 (NSS) (NSS) 5578 8915 8919 8889 5556 8987 R134a Aluminum RetroFit Service Kit Complete Kit includes everything needed to retrofit systems to R134a. Includes schrader core remover, port eliminator caps, aluminum retro charging adaptors and retrofit labels. 5532 5531 (NSS) 5533 5557 5534 EMPTY 8991 5557 5555 5556 5563 R134a RetroFit Starter Assortment Kit Complete steel fitting assortment, including retrofit labels, schrader cores and port eliminator caps. 5587 5588 8992 R12/R134a - Service Cap Kit 5574 5575 5579 (5 ea.) 5580 (5 ea.) 5578 (5 ea.) 2017 MEI Corporation 337
COMPRESSOR SERVICE PARTS RetroFit Charging Adapters and Fittings Remove & Discard R12 Caps & Valve Cores Screw On New R134a Retro Fit Adapters R12 Service Ports R12 Service Ports When retrofitting R12 systems to R134a, these fittings attach directly over the old R12 charging ports. Includes threadlock to prevent removal and new R134a schrader valve. Cap Aluminum Aluminum 5550S Weld-on Switch Port M10-1.25 5552 Primary Seal Fitting, 16mm Port Male Thread, M12-1.5 Base 5553 Low Side Primary Seal, 13mm Port Female Thread, 10mm-1.25 red cap 5555 (high side) 1/4 (7/16-20) to 16mm, red cap Includes Valve Core, Neoprene O Ring and Threadlock. blue cap (low side) 5556 1/4 (7/16-20) to 13mm, blue cap Includes Valve Core, Neoprene O Ring and Threadlock. red cap 5557 (high side) 3/16 (3/8-24) to 16mm, red cap Includes Valve Core, Neoprene O Ring and Threadlock. (Notch in nut designates 3/8 ) red cap (high side) 5558 1/4 (7/16-20) to16mm, red cap Includes Valve Core, Neoprene O Ring and Threadlock. blue cap (low side) 5559 1/4 (7/16-20) to 13mm, blue cap Includes Valve Core, Neoprene O Ring and Threadlock. Aluminum Aluminum Aluminum red cap 5560 (high side) 3/16 (3/8-24) to 16mm, red cap Includes Valve Core, Neoprene O Ring and Threadlock. (Notch in nut designates 3/8 ) red cap (high side) 5563 GM Primary RetroFit Adapter 16mm Port, red cap Male Thread 12mm-1.5 5564 OEM High Flow Port 13mm Port x M13-1.0 Includes Valve Core and Cap 5565 OEM High Flow Port 16mm Port x M15-1.0 Includes Valve Core and Cap 338 2017 MEI Corporation
RetroFit Charging Adapters and Fittings (continued) SERVICE PARTS COMPRESSOR 5583 Weld-on RetroFit Fittings 13mm Port 5584 Weld-on RetroFit Fittings 16mm Port Drier Port Adapter Fittings (for Universal Drier see page 525.) DRIER SIDE 4136 3/8 #6 Male O ring to 3/8 #6 Male Insert O ring Drier Adapter 4137 11/16 Male O ring to 3/8 #6 Male Insert O ring Drier Adapter TO DRIER 4161 M10-1.25 x 3/8-24 Male Switch Port Adapter 4162 M12-1.5 x 3/8-24 Male Metric Adapter 4165 3/8-24 to 13mm (low side) R134a Charge Port Adapter 4166 3/8-24 to 16mm (high side) R134a Charge Port Adapter 4167 7/16 Female Flare to M10-1.25 Male Switch Port Adapter 4168 M10-1.25 Female Flare to 7/16 R12 Male Flare Adapter 4913...#6 4914...#8 4919...#10 Male O ring to Flare Adapter 4922... #6 4920... #8 Male O ring to Female Flare Adapter 5447FF 8 x 8 Flare Adapter 90 Female Flare to Female Flare (Carrier A/C) 5447FO 8 x 8 O ring Adapter 90 Female O ring to Female O ring (Carrier A/C) 5527A 3/8 #6 Male O ring to 3/8 #6 Female O ring R12 Inline Charge Fitting 8900 3/8-24 Male threads to 7/16 Male Flare R12 Adapter 2017 MEI Corporation 339
COMPRESSOR SERVICE PARTS Shaft Seal Kits 5487 Sanden Compressor 5H14 & 7H15 Shaft Seal Kit 5489 GM V5 Compressor Shaft Seal Kit 5490 Tecumseh Compressor HG Model Shaft Seal Kit 5491 T/CCI, York Compressor Shaft Seal Kit Large Plate, 6 Bolts, 1/4 Heads 5492 Tecumseh/York Compressor Shaft Seal Kit Small Plate, 6 Bolts, 3/8 Heads 5493 GM A6 & R4 Compressor Shaft Seal Kit - Ceramic 5494 Ford FS6 Compressor Shaft Seal Kit 5495 Seltec/TAMA/ Valeo Compr. TM08-TM16 Shaft Seal Kit 5497 Sanden Compressor SD508 & SD510 Shaft Seal Kit SNAP RING KIT 5498 Sanden Compressor SD708 & SD709 Shaft Seal Kit TM31 SIGHT GLASS KIT 5486 York Style - Heavy, Standard Duty, and Mini Compressor Models All Refrigerant Capability Deluxe Shaft Seal Kit Kit includes: Centering tool for proper plate orientation, Felt ring for improved dust protection and oil wick control and Clutch coil replacement anti-vibration Super-Screws. 5545 Clutch Snap Ring Kit - 7H15 340 50031 TM31/VC31 Sight Glass (Set of 2) 2017 MEI Corporation
Compressor Shaft Keys SERVICE PARTS COMPRESSOR 5535 Seltec 5536 GM A6/R4 5537 Sanden/Sankyo 5538 T/CCI, York-Tecumseh Compressor Gasket Kits 5670 Ford Nippondenso FS-6 5671 Sanden 505,507,508,510,5H14 5672 Sanden 708,709,7H15 5673 T/CCI, York 206,209,210 5675 GM A-6 5676 GM R-4 5677 GM DA-6,HR-6 5679 Zexel CH Series Diesel Kiki 2017 MEI Corporation 341
COMPRESSOR SERVICE PARTS Compressor Conversion Brackets - Rotary To Upright 5501 Conversion Bracket - CUMMINS NTC & N14 Third Groove Drive Replace rotary style (round) A/C compressor to York style (upright) two cylinder on 1986 to present T400-800 Kenworth, Peterbilt COE & Conv., Freightliner Conv., and 1984 to present Volvo Class 8-9; all with Cummins NTC engine driving the compressor from the accessory drive third groove. Use clutch: #5044 std. duty #5144 heavy duty w/diode & weatherpak. 5503 Conversion Bracket - DETROIT DIESEL SERIES 60 Replace rotary style (round) A/C compressor to York style (upright) two cylinder on most vehicles with Detroit Diesel Series 60 engines. The compressor is driven by the accessory drive belts which also drives the alternator. Use clutch: #5044 std. duty #5144 heavy duty w/diode & weatherpak. Replace the T/CCI, York Tube-O Compressor with a Sanden SD7H15 Model. See page 307 for details. Note: Other Add-on A/C Compressor Bracket Kits are Available for a Number of Specific Engines. Call for Information. 342 2017 MEI Corporation
Compressor Conversion Brackets - Upright To Rotary SERVICE PARTS COMPRESSOR 5509 Universal Bracket Kit - Sanden or Seltec Requires welding for exact fit. Compressor Adapter Bracket - used for mounting compressors for different (not common) types of engine applications. 6-7/8 4-1/2 center 3-3/8 center 7-1/4 5623 Conversion Kit - T/CCI, York Style to Sanden/Seltec Adjustable compressor bracket fits most York style (upright) compressor mounts. Converts system to Sanden/Seltec standard mount compressors. 5623W Adapter Kit - T/CCI, York Style to Sanden/Seltec Weldable Bracket No slots on bottom of plate. Welds onto OE bracket. 4-1/2 center 1-1/2 4-1/2 center 3-3/8 center 4 3-3/8 center 5633 Conversion Kit - T/CCI, York Style to Sanden/Seltec Fixed compressor bracket fits most York style (upright) compressor mounts. Converts system to Sanden/Seltec standard mount compressors. Non-adjustable bracket. 5633H Conversion Kit - T/CCI, York Style to Sanden 4 High Rise Bracket Non-adjustable bracket. 2017 MEI Corporation 343