SW-IRMOM-1801 DISTINCTIVE FEATURES Screw version up to A Tactile feedback Sealed to IP6 Illuminated or non-illuminated Flat round actuator for optional marking ENVIRONMENTAL SPECIFICATIONS Front panel sealing : IP6 according to IEC 6059 Shock resistance : 100 g according to IEC 51-, test 6c Vibration resistance : 10-500Hz - 10 g according to IEC 51-, test 6d Salt spray : IEC 51-6, test 11f Operating temperature : -0 C to +85 C (-0 F to +185 F) ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : - Gold plated contacts: Code : 00 ma 8 VDC, 500,000 cycles Code : 5 A 8 VDC, 0,000 cycles - Silver contacts (code ) - screw terminals : A 8 VDC, 500,000 cycles Initial contact resistance : 100 mω max. Insulation resistance : 1 GΩ min. at 500 VDC Dielectric strength : 1,500 Vrms LED COMPONENT SPECIFICATIONS LED color Forward current Typ. forward voltage Max. forward voltage Super red (0S) 0 ma.1 V.3 V Yellow (0Y) 0 ma.1 V.3 V Green (0G) 0 ma.1 V.3 V Blue (0B) 0 ma 3. V 3.8 V White (0W) 0 ma 3.35 V.5 V Red/Green (SG) 0 ma Red: 1.95 V / green:.1 V.5 V A resistor must be series-connected by the user. Resistor value = supply voltage - LED forward voltage LED forward current On flying lead versions, the LED resistor can be integrated by APEM on request. Yellow/green (YG) 0 ma Yellow: V / green:.1 V.5 V The company reserves the right to change specifications without notice. 1
GENERAL SPECIFICATIONS Panel thickness : 8 mm (.31) max. Total travel : 1.6 mm (.06) ± 0.3 mm Typical operating force : N ± N Low level or mechanical life : 1,000,000 cycles Torque : 0.8 Nm max. applied to nut Soldering : 30 C (608 F) max. for 3 sec. TERMINALS ILLUMINATED MODELS LED Cathode (-) N-ILLUMINATED MODELS MATERIALS Case : thermoplastic UL9-V0 Actuator : polyamide 6/6 Bushing/bezel : polyamide 6/6 Contacts : and : silver, gold plated : silver (screw terminals) Multi-wire lead AWG0, section 0.6 mm LED wire : AWG6, section 0.1 mm Lens : polycarbonate Terminal seal : epoxy APEM products may be recycled at end-of-life for the re-claiming of valuable metal components. 3.0 (.133) Straight P 1.00 (.039).10 (.9) 1.0 (.0).0 (.09).80 (.110) Quick-connect Z ELECTRICAL FUNCTIONS ILLUMINATED MODELS N-ILLUMINATED MODELS MOUNTING Function 3 () Function 3 () PANEL CUT-OUT 1 8.00 Maxi (.31 max.) - Flat seal Ø16.0 (.63DIA) MATRIX MOUNTING.00 (1.063).00 (1.063) Ø16.0 (.63)
BUILD YOUR PART NUMBER BASIC PART NUMBER IR SERIES ACTUATOR SHAPES ELECTRICAL FUNCTION TERMINALS C R Square Round, curved 3 Normally open () S F Solder lugs Flying leads P Round, flat P Straight PC F Round, flush (non-illuminated - not available in satin or bright chrome) Z V Quick-connect (non-illuminated) Screw (non-illuminated), silver contact only Actuator marking available on round flat models (symbol 1 mm max.). On request. OPTIONS CONTACTS ACTUATOR COLORS BUSHING & BEZEL LED COLORS Silver, gold plated (00 ma 8 VDC) Silver, gold plated (5 A 8 VDC) Silver (screw terminals only) 1 Blue B Dark blue Black 3 Green 0 Transparent (round bezel only) Black (std) White Other : on request. Blank 0S 0Y 0G Non-illuminated Super red Yellow Green Grey 0B Blue 5 Yellow 0W White 6 Red SG Red/green White 8 Bright chrome ILLUMINATION YG Yellow/green 9 Orange Blank Non-illuminated A Satin chrome L Central lens B Bezel (round only) ABOUT THIS SERIES On the following pages, you will find successively basic part numbers of switches and options in the same order as in above chart. Notice : please note that not all combinations of above numbers are available. Refer to the following pages for further information. A sealing boot is available to protect the switches against frost and sand (P/N U15). Round models only. See "Sealing Boot" section of website. Mounting accessories : Standard hardware supplied : 1 hex nut 19 mm (.8) across flats and 1 flat seal. Hex nut P/N U615. 3
ROUND - ILLUMINATED IRR3S IRP3S LED Cathode (-) (.11).50 (.1) Also available with straight PC terminals : IR 3P. LED color is indicated by the bottom of the switch. ROUND - ILLUMINATED IRR3F 13.00 (.511) 3.00 (.905) IRP3F Wire colors : black : contact, red : LED anode (+), blue : LED cathode (-) ROUND - N-LLUMINATED IRR3S IRP3S 5.08 (.00) (.11) Also available with straight PC terminals : IR 3P and quick-connect terminals : IR 3Z. ROUND - N-LLUMINATED IRR3F 13.00 (.511) IRP3F
ROUND - N-LLUMINATED SCREW TERMINALS IRR3V IRP3V 3.50 Maxi (.95MAX) SQUARE - ILLUMINATED IRC3S LED Cathode (-) (.11).50 (.1) Also available with straight PC terminals : IRC3P. LED color is indicated by the bottom of the switch. SQUARE - ILLUMINATED IRC3F 3.00 (.905) 13.80 (.53DIA) Wire colors : black : contact, red : LED anode (+), blue : LED cathode (-) SQUARE - N-ILLUMINATED IRC3S Also available with straight PC terminals : IRC3P and quick-connect terminals : IRC3Z. 5.08 (.00) (.11) 5
IRC3F SQUARE - N-ILLUMINATED CIRDTCF-B ECH:0.9 SQUARE - N-ILLUMINATED SCREW TERMINALS CONTACTS ACTUATOR COLORS 1 B 3 5 6 8 9 A 6 Blue Dark blue Black Green Grey Yellow Red White Bright chrome Orange Satin chrome ECHELLE 0.90 CIRDTCV-A Silver, gold plated (00 ma 8 VDC) Silver, gold plated (5 A 8 VDC) Silver (screw terminals only) 3.50 Maxi (.95MAX) IRC3V 13.00 (.511)
BUSHING AND BEZEL Black (standard) White 0 Transparent (round bezel only) ILLUMINATION L B Central lens Bezel (round only) LED COLORS 0S 0Y 0G 0B 0W SG YG Super red Yellow Green Blue White Red/green Yellow/green