Page 1 of 5 SPECIFICATIONS FOR TRUCK EQUIPPED WITH AERIAL LIFT AND SERVICE BODY Pennsylvania Department of Military and Veteran Affairs Insulated Telescopic Articulating type aerial lift with the following requirements: The following specifications should be considered minimum requirements: TRUCK CAB CHASSIS SPECIFICATIONS: International 4300 4 x 2Truck Cab Chassis or Equal Two Wheel Drive 187 Wheel Base 120 Cab to axle 33,000 lb. GVW 13,000 lb. front axle capacity 20,000 lb. rear axle capacity Diesel, MaxxForce, 245HP engine Allison 3500 RDS 4 th generation controls, wide ratio 5 Speed transmission with O/D and PTO port provision. Vinyl Driver seat, non suspension, high back with integral headrest Vinyl two man passenger seat, fixed back, two integral headrests AM/FM radio Black Rubber Floor 2 11R22.5 steering tread radial front tires 4 11R22.5 all season radial rear tires Cab steps 160 AMP alternator 2 Maintenance Free 12 volt batteries, 1850 CCA Dual air brake system Air Conditioning 50 gallon fuel tank Front tow hooks Color white Manuals Required: Operators Maintenance Parts Warranty Requirements for the prime mover vehicle: Normal factory warranty Who will be responsible for transportation to and from repair location, if not on site: Dealership while under warranty If on site warranty service required, contractor may not be allowed to charge for travel time to and from site
Page 2 of 5 SPECIFICATIONS FOR TRUCK MOUNTED AERIAL WORK PLATFORM Minimum platform height 55 feet Minimum working height 60 feet Minimum platform capacity 700 lbs. Minimum platform side reach 37 feet Articulating upper boom travel 0 degrees to +160 degrees (Minimum) Articulating lower boom travel 0 degrees to +100 degrees (Minimum) Main boom travel 30 degrees to +90 degrees (Minimum) Main boom range of motion will allow the basket to touch the ground while articulating arm is fully raised Aerial lifts range of motion will allow basket to touch the ground at the trucks rear tail shelf or within two feet from the side of the truck to allow access to rear tool compartments of the service body. Stowed travel height 12 2 max 90 degrees Hydraulic powered basket rotation (Minimum) Full pressure hydraulic lever type controls at base Proportional joystick controls to operate main boom up/down, in/out, and rotation functions in basket Joystick control will not work without trigger type dead man device to allow single hand operation Basket rotation controls are lever type with lift up lock out dead man device to allow single hand operation Engine start stop in basket Continuous rotation with enclosed worm gear (Minimum) Safety harness and lanyard Primary hydraulic power to lift provided by PTO hydraulic pump, mounted to trucks transmission 24 x 48 x 42 Platform Bucket to be fully enclosed (Minimum) Platform shall be located curbside over rear axle mounts Platform cover Liner to provide additional insulation Greaseless maintenance free bushings on boom pivot points One grease fitting at booms rotation Upper boom to be constructed of filament wound fiberglass Lower boom to be constructed of high strength steel tubing with a high density fiberglass insulator Upper boom to have a minimum 15.9 insulating fiberglass Lower boom to have a 18 min insulating fiberglass Two (2) hydraulic tool outlets at platform with two (2) sets of quick disconnect couplings 30 gallon minimum hydraulic reservoir system used for operating the boom functions. (Whatever size is needed for proper lift operation) Aerial lifts base to provide an adequate opening with a door or cover to allow access to the internal components. Aerial lifts base to provide a hydraulic reservoir fill indicator that shall be clearly visible and labeled to indicate the condition of the oil level All steel construction of lifts pedestal and base Two (2) ring style cone holder, installed beneath the tailshelf, one (1) curbside and one (1) streetside 46 KV category C rating (Minimum)
Page 3 of 5 Extension and retraction of boom done by hydraulic components to be within the pedestal and boom sections. One year parts and labor warranty for the Bucket/Lift Unit: Bumper to Bumper (i.e. the entire unit) MATERIAL HANDLING JIB AND WINCH: The material handling function includes a jib and winch that are positioned on the street side of the boom The jib is hydraulically controlled to allow the operator to position the load vertically with a control valve located at the upper control valve. The jib pole is hydraulically adjusted to position the length of the reach required A load chart near the operators control station informs the operator of the jib and boom carrying capacities Depending on boom and jib configuration up to 2,000 lbs of winch and jib capacity is available The jib assembly shall be independent of the basket leveling system. The hydraulic jib cylinder shall include its own holding valve, which prevents cylinder creep and to lock the cylinder in the event of hydraulic hose failure. The self locking worm gear winch is controlled from both the upper and the lower control valves. 80 of 7/16 double braid synthetic rope with clevis hook provided (Minimum) MID & REAR MOUNT A FRAM OUTRIGGERS W/ SUBFRAME: Hydraulic activated outriggers with flat shoes shall be attached to the frame of the chassis between the cab and the body. Hydraulic activated outriggers with flat shoes shall be attached to the frame of the chassis at the rear of the body A sub frame attached to the frame of the truck shall secure the outriggers and the aerial lift to form one integral mount The outriggers shall have a minimum vertical travel clearance of 14 Outriggers shall be capable of extending to a 145 spread The outrigger legs shall consist of inner and outer telescoping structural tubing Adjustable, polyethylene wear pads, to prevent wear and vibration during road transport shall center the inner and outer tubes Controls for each cylinder will be supplied and mounted at the rear of the chassis so the outrigger legs can be seen when in use. Outrigger Motion Alarm The completed unit shall be certified, as passing A.N.S.I. A92.2 stabilization tests with the use of two sets of outriggers and successful bidder shall demonstrate these capabilities upon delivery. STEEL SERVICE BODY 16 gauge Galvanealed body construction 120 CA chassis with dual rear wheels O.E.M. standard fender panels Body underside completely undercoated
Page 4 of 5 Body finish paint color shall be White 158 overall body length (Minimum) 93 overall body wide (Minimum) 46 overall body height (Minimum) 18 body compartment depth (Minimum) Nonskid compartment tops Flow through ventilation in body Steel doors with automotive type door seals Stainless steel door latches and hardware Stainless steel hinges and door cables Steel understructure 1/8 steel tread plate floor (Minimum) Smooth header panel Full length drip rail Exterior light package with lights in tail shelf Street side #1 vertical front compartment to 3 adjustable shelves with removable divider Street side #2 vertical front compartment to have 6 locking swivel hooks on adjustable rails, 1 4 1 configuration Street side #3 vertical front compartment to have 6 locking swivel hooks on adjustable rails, 1 4 1 configuration Street side horizontal compartment 1 fixed shelf extending through to rear vertical Street side rear outrigger housing Curbside #1 vertical front compartment to have 3 adjustable shelves with removable divider Curbside #2 vertical front compartment to have 6 locking swivel hooks on adjustable rails, 1 4 1 configuration Curbside #3 vertical front compartment to have Gripstrut access with three (3) steps (one underbody step) and two (2) sloped grab handles Curbside horizontal front compartment to have 2 shelves Curbside rear outrigger housing Curbside rear body to have hot stick door with through shelf from rear to front of body Fiber glow compartment lighting 24 steel tail shelf with anti skid coating, side access step cut out and cable step (Minimum) Grab handles on back of body for accessing cargo area Rear of cargo area to have tail board holder with board Wheel chock holders in curbside wheel well Outrigger pad holders mounted under body Four Two curbside of body Two street side of body MISCELLANEOUS ACCESSORIES: Back up alarm Mud flaps 5 lb. Fire Extinguisher with bracket installed Triangular Reflector Kit Standard Decal and Placard Kit for Aerial Unit T 125 Style Pintle Hook (30,000 lb. MGTW with 6,000 lb. MVL)
Page 5 of 5 Set of eye bolts for trailer safety chain, installed one each side of towing devise mount Glad Hands at rear of truck 7 way trailer receptacle, pin type Electric brake controller installed in cab Lights and reflectors in accordance with FMVSS #108 lighting package Heavy duty square tube cab guard that protects the entire cab to include; rear cab guard support, heavy duty tube bumper support for cab guard, rear window protector and boom saddle. Two Amber LED strobe lights mounted onto cab guard LED four corner amber strobe lights mounted in front of truck cab chassis and rear tail shelf of aerial service body. LED directional amber strobe bar mounted in tail shelf of service body 3000 watt max output DC to AC power inverter wired to auxiliary power source AC outlet mounted in rear curbside of tail shelf and wired to inverter. Two rubber wheel chocks Remote controlled directional spotlight mounted to cab guard. Basket cover