FSAF4(-S) US, FSAF10(-S) US On/Off, Spring Return, Meets 50 F [11 C] for Half Hour, 75 Seconds Torque min. 133 in-lb, for control of air dampers Technical Data FSAF4(-S) US, FSAF10(-S) US Power supply FSAF4(-S) US 4 VAC ± 0%, 4 VDC -10% +0% FSAF10(-S) US 10 VAC ± 10%, 50/60 Hz Power consumption FSAF4(-S) US running 7.5 W, 10 VA,.4 A holding W, 4 VA,.15 A FSAF10(-S) US running 50/60Hz: 9.5 W, 11 VA,.1 A holding 3.5 W, 6 VA,.05 A Transformer sizing 10 VA (Class power source 4V only) Electrical connection motor 3 ft, 18 ga, color coded leads 1/ conduit connectors -S models 3 ft, 18 ga, 4 leads appliance cable 1/ conduit connectors Overload protection electronic throughout 0 to 95 rotation Angle of rotation mechanically limited to 95 Torque 133 in-lb [15 Nm] constant Direction of rotation spring reversible with cw/ccw mounting Position indication visual indicator, 0 to 95 (0 is spring return position) Manual override 3mm hex crank (shipped w/actuator) Running time <75 sec. constant, independent of load spring <0 seconds nominal Humidity 5 to 95% RH non-condensing Ambient temperature normal duty - F to 1 F [-30 C to 50 C] safety duty 3 on/off cycles after 30 minutes at ambient temperature of 50 F [11 C] Storage temperature -40 F to 176 F [-40 C to 80 C] Housing NEMA type 1 / IP40 Housing material zinc coated metal Gears permanently lubricated Agency listings culus listed to UL873 and CAN/CSA C. No.4 Noise level (max) 45 db (A) spring return 6 db Servicing Maintenance free Quality standard ISO 9001, 5 year Belimo warranty Weight (standard / -S model) FSAF4(-S) US 5.7 / 6. lbs (.6 /.8 kg) FSAF10(-S) US 6.1 / 6.6 lbs (.8 / 3 kg) Application For two position control of UL555S rated dampers in HVAC. Actuator sizing should be done in accordance with the damper manufacturer s specifications. The actuator is mounted directly to a damper shaft or jackshaft 3/8 to 1.05 in diameter by means of its universal clamp. A crank arm and mounting brackets are available if the actuator cannot be direct coupled to the jackshaft or damper shaft. Square footage of damper operated will depend on make and model of damper. Typically 1 sq.ft. minimum up to 4 sq.ft maximum will be operated for UL555S applications. Operation The FSAF series actuators provide true spring return operation for reliable fail-safe application and positive close-off on UL555S dampers. The spring return system provides constant torque to the damper with, and without, power applied to the actuator. The FSAF series provides 95 of rotation and is provided with a graduated position indicator showing 0 to 95. The FSAF has a manual positioning mechanism which allows the setting of any damper position within its 95 of rotation. The actuator is shipped in the zero fail-safe position to provide automatic compression against damper gaskets for tight shut-off. When power is applied, the manual mechanism is released and the actuator drives toward the open position where it stops rotating. The manual override can also be released physically by the use of a crank supplied with the actuator. SAFETY NOTE Screw a conduit fi tting into the actuator s bushing. Jacket the actuator s input and output wiring with suitable fl exible conduit. Properly terminate the conduit in a suitable junction box. Dimensions (Inches [mm]) Standard: 1/" to 1.05" Optional* 3/8" to 3/4" 3/8" to 5/8" *with K4 US clamp 0.65" [16.5] 3.5" [8.7].4" [57] 0.39" [10] 0.35" [9] 3.86" [98] 0.19" [5] 3.15" [80].64" [67] 1.97" [50] 10.59" [69] 5.85" [148.5] 0.6" [6.5] 004 D0 1.93" [49] FSAF4-S US, FSAF10-S US Auxiliary Switch xspst 7A resistive,.5a inductive at 10V or 50V, UL Approved, double-insulated, one switch at 10, one adjustable from 30 to 90 171
FSAF10(-S) US, FSAF4(-S) US On/Off, Spring Return, Meets 50 F [11 C] for Half Hour, 75 Seconds Accessories (AF series accessories may be employed) IND-AF Damper position indicator K4 US Universal clamp for 3/8 to 3/4 shafts K4-1 US Universal clamp for up to 1.05 dia. jackshafts K4-H Universal clamp for hexshafts 3/8 to 5/8 KH-AF Crank arm for up to 3/4 round shaft (Series ) KH-AF-1 Crank arm for up to 1.05 jackshaft (Series ) KH-AFV V-bolt kit for KH-AF and KH-AF-1 Tool-01 10 mm wrench ZDB-AF US Angle of rotation limiter ZG-100 Universal mounting bracket ZG-101 Universal mounting bracket ZG-10 Multiple actuator mounting bracket ZG-103 Universal mounting bracket ZG-104 Universal mounting bracket ZG-106 Mounting bracket for Honeywell Mod IV replacement or new ZG-107 Mounting bracket for Honeywell Mod III or Johnson Series 100 replacement or new ZG-108 Mounting bracket for Barber Colman MA 3../4.., Honeywell Mod III or IV or Johnson Series 100 replacement or new ZG-AF Crank arm adaptor kit for AF/NF ZG-AF108 Crank arm adaptor kit for AF/NF ZS-100 Weather shield (metal) ZS-150 Weather shield (polycarbonate) ZS-300 NEMA 4X housing 965-00001 1mm form fit square shaft adaptor For an overview of how to apply the accessories, see Belimo Mechanical Accessories and refer to the Belimo Mounting Methods Guide. NOTE: When using FSAFxx (-S) US actuators, only use accessories listed on this page. Wiring Diagrams 1 Provide overload protection and disconnect as required. CAUTION Equipment Damage! Actuators may be connected in parallel. Power consumption and input impedance must be observed. 3 Actuator may also be powered by 4 VDC. 4 No ground connection required. Double insulated. 5 For end position indication, interlock control, fan startup, etc., the FSAF4- S US and FSAF10-S US incorporates two built-in auxiliary switches: x SPST, 7A resistive,.5 inductive @10/50 VAC, UL Approved, one switch is fi xed at 10, one is adjustable from 30 to 90. Meets UL requirements without the need of an electrical ground connection. Meets culus or UL and CSA Standard requirements without the need of an electrical ground connection. WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Typical Specification Large combination fi re and smoke dampers are to be operated by Belimo FSAF series actuators. Manufacturer shall provide 5 year warranty. Actuators shall draw no more than 11VA at 10V or 4V. Where auxiliary switches are required for signaling, starting fans, or position indication, -S model actuators, damper blade, or proximity switches shall be provided. Smaller dampers shall employ Belimo FSLF or FSNF actuators per damper manufacturer recommendations. FSAF4 US and FSAF10 US W19_08 17
FSAF30(-S) US On/Off, Spring Return, 50 F [11 C] for Half Hour, 75 Seconds Torque min. 133 in-lb, for control of air dampers Technical Data FSAF30(-S) US Power supply 30 VAC ± 14%, 50/60 Hz Power consumption running 50/60Hz: 11 W, 1 VA,.07 A holding 3.5 W, 6 VA,.03 A Transformer sizing 10 VA (Class power source 4V only) Electrical connection motor 3 ft, 18 ga, color coded leads 1/ conduit connectors -S models 3 ft, 18 ga, 4 leads appliance cable 1/ conduit connectors Overload protection electronic throughout 0 to 95 rotation Angle of rotation mechanically limited to 95 Torque 133 in-lb [15 Nm] constant Direction of rotation spring reversible with cw/ccw mounting Position indication visual indicator, 0 to 95 (0 is spring return position) Manual override 3mm hex crank (shipped w/actuator) Running time <75 sec. constant, independent of load spring <0 seconds nominal Humidity 5 to 95% RH non-condensing Ambient temperature normal duty - F to 1 F [-30 C to 50 C] safety duty 3 on/off cycles after 30 minutes at ambient temperature of 50 F [11 C] Storage temperature -40 F to 176 F [-40 C to 80 C] Housing NEMA type 1 / IP40 with fl exible conduit Housing material zinc coated metal Gears permanently lubricated Agency listings culus listed to UL873 and CAN/CSA C. No.4 Noise level (max) 45 db (A) spring return 6 db Servicing Maintenance free Quality standard ISO 9001, 5 year Belimo warranty Weight 6.9 lbs (3.1 kg) Application For two position control of UL555S rated dampers in HVAC. Actuator sizing should be done in accordance with the damper manufacturer s specifications. The actuator is mounted directly to a damper shaft or jackshaft 3/8 to 1.05 in diameter by means of its universal clamp. A crank arm and mounting brackets are available if the actuator cannot be direct coupled to the jackshaft or damper shaft. Square footage of damper operated will depend on make and model of damper. Typically 1 sq.ft. minimum up to 4 sq.ft maximum will be operated for UL555S applications. Operation The FSAF series actuators provide true spring return operation for reliable fail-safe application and positive close-off on UL555S dampers. The spring return system provides constant torque to the damper with, and without, power applied to the actuator. The FSAF series provides 95 of rotation and is provided with a graduated position indicator showing 0 to 95. The FSAF has a manual positioning mechanism which allows the setting of any damper position within its 95 of rotation. The actuator is shipped in the zero fail-safe position to provide automatic compression against damper gaskets for tight shut-off. When power is applied, the manual mechanism is released and the actuator drives toward the open position where it stops rotating. The manual override can also be released physically by the use of a crank supplied with the actuator. SAFETY NOTE Screw a conduit fi tting into the actuator s bushing. Jacket the actuator s input and output wiring with suitable fl exible conduit. Properly terminate the conduit in a suitable junction box. Dimensions (Inches [mm]) Standard: 1/" to 1.05" Optional* 3/8" to 3/4" 3/8" to 5/8" *with K4 US clamp 0.65" [16.5] 3.5" [8.7].4" [57] 0.39" [10] 0.35" [9] 3.86" [98] 0.19" [5] 3.15" [80].64" [67] 1.97" [50] 10.59" [69] 5.85" [148.5] 0.6" [6.5] 004 D0 1.93" [49] FSAF30-S US Auxiliary Switch xspst 7A resistive,.5a inductive at 10V or 50V, UL Approved, double-insulated, one switch at <10, one adjustable from >30 to 90 173
FSAF30(-S) US On/Off, Spring Return, 50 F [11 C] for Half Hour, 75 Seconds Accessories (AF series accessories may be employed) IND-AF Damper position indicator K4 US Universal clamp for 3/8 to 3/4 shafts K4-1 US Universal clamp for up to 1.05 dia. jackshafts K4-H Universal clamp for hexshafts 3/8 to 5/8 KH-AF Crank arm for up to 3/4 round shaft (Series ) KH-AF-1 Crank arm for up to 1.05 jackshaft (Series ) KH-AFV V-bolt kit for KH-AF and KH-AF-1 Tool-01 10 mm wrench ZDB-AF US Angle of rotation limiter ZG-100 Universal mounting bracket ZG-101 Universal mounting bracket ZG-10 Multiple actuator mounting bracket ZG-103 Universal mounting bracket ZG-104 Universal mounting bracket ZG-106 Mounting bracket for Honeywell Mod IV replacement or new ZG-107 Mounting bracket for Honeywell Mod III or Johnson Series 100 replacement or new ZG-108 Mounting bracket for Barber Colman MA 3../4.., Honeywell Mod III or IV or Johnson Series 100 replacement or new ZG-AF Crank arm adaptor kit for AF/NF ZG-AF108 Crank arm adaptor kit for AF/NF ZS-100 Weather shield (metal) ZS-150 Weather shield (polycarbonate) ZS-300 NEMA 4X housing 965-00001 1mm form fit square shaft adaptor For an overview of how to apply the accessories, see Belimo Mechanical Accessories and refer to the Belimo Mounting Methods Guide. NOTE: When using FSAFxx (-S) US actuators, only use accessories listed on this page. Wiring Diagrams 1 Provide overload protection and disconnect as required. CAUTION Equipment Damage! Actuators may be connected in parallel. Power consumption and input impedance must be observed. 3 Actuator may also be powered by 4 VDC. 4 No ground connection required. Double insulated. 5 For end position indication, interlock control, fan startup, etc., the FSAF30-S US incorporates two built-in auxiliary switches: x SPST, 7A resistive,.5 inductive @10/50 VAC, UL Approved, one switch is fi xed at 10, one is adjustable from 30 to 90. Meets UL requirements without the need of an electrical ground connection. Meets culus or UL and CSA Standard requirements without the need of an electrical ground connection. WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Typical Specification Large combination fi re and smoke dampers are to be operated by Belimo FSAF series actuators. Manufacturer shall provide 5 year warranty. Actuators shall draw no more than 1VA at 30V or 10 VA at 4V. Where auxiliary switches are required for signaling, starting fans, or position indication, -S model actuators, damper blade, or proximity switches shall be provided. Smaller dampers shall employ Belimo FSLF or FSNF actuators per damper manufacturer recommendations. FSAF4 US and FSAF30 US W439_08 174
FSAF4-SR(-S) US Proportional, Spring Return, 4 V, to 10 VDC or 4 to 0 ma control signal Operation at 50 F for limited time per UL555S testing Torque min. 133 in-lb, for control of air dampers Technical Data Power supply Power consumption Transformer sizing Electrical connection FSAF4-SR FSAF4-SR(-S) US 4 VAC ± 0% 50/60 Hz 4 VDC ± 10% running 7 W, 11 VA holding 3 W, 5 VA 15 VA (class power source) 3 ft, 18 GA, 4 color coded leads (4V) 1/ conduit connector FSAF4-SR-S 3 ft, 18 GA appliance cable 1/ conduit connector Overload protection electronic throughout 0 to 95 rotation Operating range to 10 VDC, 4 to 0mA Input impedance 100 kω (0.1 ma), 500 Ω Feedback output U to 10 VDC (max. 0.5 ma) for 95 Angle of rotation mechanically limited to 95 Torque 133 in-lb [15 Nm] constant Direction of rotation spring reversible with cw/ccw mounting The control direction switch is not present. Direct acting only. VDC=Fail-safe position. Position indication visual indicator, 0 to 95 (0 spring return position) Manual override 3mm hex crank (shipped w/actuator) Running time motor <75 sec. constant, independent of load spring < 0 seconds Humidity 5 to 95% RH non-condensing Ambient temperature normal duty - F to 1 F [-30 C to 50 C] safety duty 3 on/off cycles after 30 minutes at ambient temperature of 50 F [11 C] Storage temperature -40 F to 176 F [-40 C to 80 C] Housing NEMA type / IP40 Housing material zinc coated metal Agency listings culus to UL873 and CSA C. No. 4-93 Noise level (max) running 45 db (A) Servicing maintenance free Quality standard ISO 9001, 5 year Belimo warranty Weight 6.0 lbs (.7 kg.) Application For proportional modulation of UL555S rated dampers in HVAC. Actuator sizing should be done in accordance with the damper manufacturer s specifications. The actuator is mounted directly to a damper shaft or jackshaft up to 1.05 in diameter by means of its universal clamp. A crank arm and mounting brackets are available if the actuator cannot be direct coupled to the jackshaft or damper shaft. The actuator operates in response to a to 10 VDC, or with the addition of a 500 Ω resistor, a 4 to 0 ma control input from an electronic controller or positioner. A to 10 VDC feedback signal is provided for position indication or master-slave applications. See Application Bulletin for details. Operation The FSAF series actuators provide spring return operation. There is no reversing switch on the FSAF4-SR. It is direct acting only. A reverse acting signal is required if it must spring open while V signal drives it closed. The torque is asymmetrical giving 180 in-lb drive and 133 in-lb spring. The FSAF resets after being driven or springing closed to the 0 position. There is a possible hysteresis of 1 every 1000 changes in signal. This can cause a position shift. It is recommended that power or signal be reset once a week. A manual override winder and locking mechanism is provided. If the manual winder is used when the actuator is powered, the actuator will release and drive closed to reset the 0 degree position. The actuator may not be mechanically parallelled or piggybacked. Each damper section should be controlled by a separate actuator. The wire 5 feedback can be used to parallel up to five additional actuators. If less than.1 V or greater than 9.9V is given wire 3, actuator drives all the way to the respective end stop. The FSAF uses a DC motor which is controlled by a microchip The actuator may be stalled anywhere during its rotation without damage. If power is removed, the damper will spring closed. Interlocks must be provided as necessary for life safety functions and to shut down fan if required. SAFETY NOTE Screw a conduit fi tting into the actuator s bushing. Jacket the actuator s input and output wiring with suitable fl exible conduit. Properly terminate the conduit in a suitable junction box. Dimensions (Inches [mm]) Standard: 1/" to 1.05" Optional* 3/8" to 3/4" *with K4 US clamp 0.65" [16.5] 3.86" [98] 3.10" [78] 3.15" [80].4" [57] 0.19" [5] 0.39" [10] 0.35" [9].64" [67] 10.59" [69] 5.85" [148.5] 0.6" [6.5] 1.93" [49] D001(old) FSAF4-SR-S US x SPDT 7A resistive,.5a inductive at 10/50VAC. UL Approved, double-insulated, one set at =+10, one adjustable 30 to 90 1.97" [50] 175
FSAF4-SR(-S) US Proportional, Spring Return, 4 V, to 10 VDC or 4 to 0 ma control signal Operation at 50 F for limited time per UL555S testing Accessories (AF series accessories may be employed) IND-AF Damper position indicator K4 US Universal clamp for 3/8 to 3/4 shafts K4-1 US Universal clamp for up to 1.05 dia. jackshafts K4-H Universal clamp for hexshafts 3/8 to 5/8 KH-AF Crank arm for up to 3/4 round shaft (Series ) KH-AF-1 Crank arm for up to 1.05 jackshaft (Series ) KH-AFV V-bolt kit for KH-AF and KH-AF-1 Tool-01 10 mm wrench SGA4 Min. and/or max. positioner in NEMA 4 housing SGF4 Min. and/or max. positioner for flush panel mounting ZG-R01 500 Ω resistor for 0 to 0 ma control signal ZDB-AF US Angle of rotation limiter ZG-100 Universal mounting bracket ZG-101 Universal mounting bracket ZG-10 Multiple actuator mounting bracket ZG-103 Universal mounting bracket ZG-104 Universal mounting bracket ZG-106 Mounting bracket for Honeywell Mod IV replacement or new ZG-107 Mounting bracket for Honeywell Mod III or Johnson Series 100 replacement or new ZG-108 Mounting bracket for Barber Colman MA 3../4.., Honeywell Mod III or IV or Johnson Series 100 replacement or new ZG-AF Crank arm adaptor kit for AF/NF ZG-AF108 Crank arm adaptor kit for AF/NF ZS-100 Weather shield (metal) ZS-150 Weather shield (polycarbonate) ZS-60 Explosion-proof housing ZS-300 NEMA 4X housing For an overview of how to apply the accessories, see Belimo Mechanical Accessories and refer to the Belimo Mounting Methods Guide. NOTE: When using FSAF4-SR(-S) US actuators, only use accessories listed on this page. 4 No ground connection required. Double insulated. 5 Only connect common to neg. ( ) leg of control circuits. 6 For end position indication, interlock control, fan startup, etc., FSAF4-SR-S US incorporates two built-in auxiliary switches: x SPDT, 7A resistive,.5a inductive 10/50 VAC, UL Approved, one switch is fi xed at 10, one is adjustable 30 to 90. Meets UL requirements without the need of an electrical ground connection. The ZG-R01 500 Ω resistor converts the 4 to 0 ma control signal to to 10 VDC. WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. W188_08 Typical Specification Proportional smoke, and combination fi re and smoke dampers, shall be controlled by Belimo FSAF4-SR actuators. The control signal shall provide proportional damper control in response to a to 10 VDC or, with the addition of a 500 Ω resistor, a 4 to 0 ma control input from an electronic controller or positioner. The actuators must be designed so that they may be used for either clockwise or counter clockwise fail-safe operation. Actuator shall open damper in <75 seconds per UL555S and shall spring closed in under 0 seconds. Actuators shall be UL Approved, have a 5-year warranty, and be manufactured under ISO 9001 International Quality Control Standards. Actuators shall be as manufactured by Belimo. Actuators with auxiliary switches must be constructed to meet the requirement for double insulation so an electrical ground connection is not required to meet agency listings. Replacement Application The number one equal or better requirement for use as a replacement for obsolete defective motors is the UL555S listing of the Belimo actuator with the damper for the application. The local authority having jurisdiction sets the requirements since UL has stated that they do not regulate replacements. Wiring Diagrams Proportional control W57_08 1 Provide overload protection and disconnect as required. CAUTION Equipment Damage! Actuators may be connected in parallel. Power consumption and input impedance must be observed. 3 Actuator may also be powered by 4 VDC. 176
FSAF4-BAL(-S) US Spring Return, 4 V, 3-Position, 100% Open Override Operation at 50 F for limited time per UL555S testing Technical Data Power supply FSAF4-BAL(-S) US 4 VAC ± 0% 50/60 Hz 4 VDC ± 10% Power consumption running AC 9.5 VA 6.5W DC 6W holding AC 5 VA 3W DC 3W Transformer sizing 10 VA (class power source 4V only) Electrical connection 3 ft, 18 GA, 1/ conduit connector Overload protection electronic throughout 0 to 95 rotation Control signal 4 VAC/DC 3-position Angle of rotation 0 to 95, pot adjustable Torque 133 in-lb [15 Nm] Direction of rotation spring reversible with cw/ccw mounting Position indication visual indicator, 0 to 95 (0 spring return position) Manual override 3mm hex crank (shipped w/actuator) Running time motor <75 seconds @ 50 F [11 C] spring < 0 seconds Humidity 5 to 95% RH non-condensing Ambient temperature - F to 1 F [-30 C to 50 C] Storage temperature -40 F to 176 F [-40 C to 80 C] Housing NEMA type 1/IP40 (with flex conduit) Housing material zinc coated metal Agency listings culus to UL873 and CSA C. No. 4-93 Noise level (max) running <45 db(a) spring <6dB(A) Servicing maintenance free Quality standard ISO 9001, 5 year Belimo warranty Weight 5.3 lbs (.4 kg) 5.7 lbs (.6 kg) for -S model FSAF4-BAL-S US x SPDT 7A resistive,.5a inductive at 10/50VAC. UL listed, double-insulated, one switch is set at 10, one is adjustable 30 to 90 Application For 3-position control of UL555S rated dampers in HVAC. Actuator sizing should be done in accordance with the damper manufacturer s tests. In the absence of other information, use 10 in-lb of torque per square foot of area for opposed blade and 14 in-lb for parallel blade fire and smoke dampers at 1000 fpm air velocity. The FSAF4-BAL is specifically designed to balance the air flow in ducts and simultaneously provide control of fire and smoke dampers. 0V = spring closed. 4V on wire, not 3 = drive to the potentiometer position (balanced flow). 4V on wire 3, regardless of the status of wire = drive full open (smoke control extraction or pressurization). See Application Bulletin for details. Operation For 3-position control of UL555S rated dampers in HVAC. Actuator sizing should be done in accordance with the damper manufacturer s tests. In the absence of other information, use 10 in-lb of torque per square foot of area for opposed blade and 14 in-lb for parallel blade fire and smoke dampers at 1000 fpm air velocity. The FSAF4-BAL is specifically designed to balance the air flow in ducts and simultaneously provide control of fire and smoke dampers. 0V = spring closed. 4V on wire, not 3 = drive to the potentiometer position (balanced flow). 4V on wire 3, regardless of the status of wire = drive full open (smoke control extraction or pressurization). SAFETY NOTE The actuator contains no components which the user can replace or repair. Dimensions (Inches [mm]) Standard Optional ½ to 1.05 ½ 0.65" [16.5] 3.5" [8.7].4" [57] 0.39" [10] 0.35" [9] 3.86" [98] 0.19" [5] 3.15" [80].64" [67] 1.97" [50] 10.59" [69] 5.85" [148.5] 0.6" [6.5] 1.93" [49] 70793-00001.pdf 177
FSAF4-BAL(-S) US Spring Return, 4 V, 3-Position, 100% Open Override Operation at 50 F for limited time per UL555S testing Accessories (AF series accessories may be employed) IND-AF Damper position indicator K4-1 US Universal clamp for up to 1.05 dia. jackshafts KH-AF Crank arm for up to 3/4 round shaft (Series ) KH-AF-1 Crank arm for up to 1.05 jackshaft (Series ) KH-AFV V-bolt kit for KH-AF and KH-AF-1 Tool-01 10 mm wrench ZDB-AF Angle of rotation limiter ZG-100 Universal mounting bracket ZG-101 Universal mounting bracket ZG-103 Universal mounting bracket ZG-104 Universal mounting bracket ZG-106 Mounting bracket for Honeywell Mod IV replacement or new ZG-107 Mounting bracket for Honeywell Mod III or Johnson Series 100 replacement or new ZG-108 Mounting bracket for Barber Colman MA 3../4.., Honeywell Mod III or IV or Johnson Series 100 replacement or new ZG-AF Crank arm adaptor kit for AF/NF ZG-AF108 Crank arm adaptor kit for AF/NF ZS-100 Weather shield (metal) ZS-150 Weather shield (polycarbonate) ZS-300 NEMA 4X housing 965-00001 1 mm form fit square shaft adaptor For an overview of how to apply the accessories, see Belimo Mechanical Accessories and refer to the Belimo Mounting Methods Guide. NOTE: When using FSAF4-BAL(-S) US actuators, only use accessories listed on this page. Typical Specification Where indicated on drawings, combination fi re and smoke and balancing dampers shall be controlled by Belimo FSAF4-BAL or equal actuators. The actuators must be designed so that they may be used for either clockwise or counter clockwise failsafe operation. Actuator shall open damper in <75 seconds per UL555S and shall spring closed in under 0 seconds. Actuators shall have a 5-year warranty and be manufactured under ISO9001 International Quality Control Standards. Actuator shall have an adjustable Maximum Opening Potentiometer which shall be used by the TAB contractor to adjust fl ow to that portion of the system fed by the damper. The actuator shall spring closed if either the smoke detector or alarm system removes power from it. Actuator shall spring closed if the primary temperature thermodisc opens due to high ambient of >165 F or as otherwise indicted on drawings. The actuator shall drive full open if either the smoke control system 100% open override or Fire Fighters Smoke Control Station override is activated. Damper shall spring closed again if the thermodisc of a combination fi re and smoke damper opens due to high temperature (typically 50 F). Wiring Diagrams 1 Provide overload protection and disconnect as required. CAUTION Equipment Damage! Actuators may be connected in parallel. Power consumption and input impedance must be observed. 3 Actuator may also be powered by 4 VDC. 4 Only connect Hot, Wire to Wire 3 override control 5 6 6 For end position, interlock control, fan start-up, etc., FSAF4-BAL-S incorporates two built-in auxiliary switches: x SPDT, 7A resistive,.5a inductive 10/50 VAC, UL listed, one switch is fi xed at 10, one adjustable 30 to 90 For end position indication, interlock control, fan startup, etc., FSAF4-SR-S US incorporates two built-in auxiliary switches: x SPDT, 7A resistive,.5a inductive 10/50 VAC, UL Approved, one switch is fi xed at 10, one is adjustable 30 to 90. Meets UL requirements without the need of an electrical ground connection. 7 Double insulated WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 1 Line Volts Override control 4 VAC Transformer 4 OVERRIDE CONTROL See Wiring Diagrams on following pages for typical methods. S1 NC S S3 NO S4 NC S5 S6 NO 1 Blk Com Red Hot 3 3 Override Open 6 FSAF4-BAL US 10 30 to 90 FSAF4-BAL-S US 5 7 70793-00001_pg 70793-00001_pg 178