CENTRIFUGAL IMMERSION PUMPS FLUX CENTRIFUGAL IMMERSION PUMPS QUALITY THAT SETS STANDARDS Manufactured at our main plant, these ranges of immersion pumps are the result of extensive product and process evaluation by our research and development department. They are a true FLUX product, from conception through to manufacture, assembly and testing. Their design philosophy, and the materials selected for their construction make them ideal for applications in the chemical industry, surface treatment, electroplating, printed circuit manufacturing, water treatment and wastewater treatment. FLUX centrifugal immersion pumps can be used whenever liquids have to be transferred or circulated. They are suitable for use with a wide variety of acids and alkalis as well as other chemicals, typically coolants, lubricants and non-flammable solvents. With delivery rates of up to 74 m 3 /h and delivery heads of maximum 35 m water column, FLUX centrifugal immersion pumps combine maximum efficiency with a robust and reliable construction, resulting in a pump that provides the ultimate in process security. These are features that you can rely on, each hour, 4 hours a day. The mechanical seal types F 6 and F 64 are designed for typical liquid transfer operations, with either stationary or portable variants. These units compliment the well-proven barrel pumps range and have a higher output and kw-rating. Top of the range, are the sealless units, these pumps complete the range of high output, high reliability immersion pumps. Designed for continuous use with a wide range of aggressive liquids, from acids to alkalis, the range includes the type F 76 with only a sleeve bearing in contact with the liquid or the types F 716 and F 76 - with a suspended free-flying shaft and no bearings or seals in contact with the liquid. Three-phase drive motors are available as matched power units in kw-ratings from,37 to 5,5 kw, protected to IP 55 as well as explosion-proof to EEx e II T3 for models F 6, F 64, F 76 and F 76. With immersion lengths from 3 to 4 mm almost every application requirement can be met. The use of high-class materials such as Hastelloy C and polyvinylidenfluoride, together with polypropylene and stainless steel, are combined with design experience perfected over decades of pump manufacturing. This guarantees the long service life of FLUX centrifugal immersion pumps. Detailed information and performance charts are shown on the following pages. To receive a quotation compiled to your application, please could you to fill in the questionnaire on page. and return it to us.
FLUX FLUX TAUCHKREISELPUMPEN EIN STARKES PUMPENPROGRAMM SAFE, POWERFUL, RELIABLE THE NEW FLUX RANGE With 4 different design formats within the vertical centrifugal immersion pump range FLUX offer a cost effective, reliable solution for many liquid transfer and circulating operations. With these pumps FLUX meet the requirements of the market with their forward-looking designs and the manufacture of high quality products. Type F 76: 4 different sizes, sealles design with sleeve bearing, immersion length up to mm Type F 76: very robust construction with shaft bearing located in a pedestal, version with support bars for continuous use, suitable for dry operation Type F 6 and F 64: with mechanical seal in vertical and horizontal version Type F 716: compact design requires little space for installation, version with support tube or support bars for continuous use, suitable for dry operation.1.
FLUX 3 4 5 6 7 8 9 NEW Introduction Table of contents FLUX Centrifugal Immersion Pumps F 6 S Size and 3 in stainless steel for delivery rates of up to 3 m 3 /h FLUX Centrifugal Immersion Pumps F 64 PP Size, 3, Z and 3 Z in polypropylene for delivery rates of up to 34 m 3 /h FLUX Centrifugal Immersion Pumps F 64 PP and F 64 PVDF Size 185 in polypropylene or polyvinylidenfluoride for delivery rates of up to 4 m 3 /h TABLE OF CONTENTS FLUX CENTRIFUGAL IMMERSION PUMP F 6 S IN STAINLESS STEEL SIZE AND 3 Typical Applications Transferring low flammability liquids up to a viscosity of 5 mpas (cp) from containers or tanks, either open topped or closed. Suitable for stationary or portable applications. Construction features Centrifugal pump in stainless steel consisting of an inner tube and outer tube. The centrifugal impeller in the pump housing is driven by the motor via the drive shaft. The drive shaft is supported by intermediate bearings within the inner tube, a mechanical seal separates the liquid from the bearings and upper shaft. This construction provides the ultimate in stability, and ensures the maximum integrity of the mechanical seal. With an open conical impeller. 1 11 FLUX Centrifugal Pumps F 6 S TR and F 64 PP TR in horizontal version for delivery rates of up to 44 m 3 /h Three-phase motors in differing kw-ratings are available as a matched power unit. Connection to the pump is made via a flexible coupling. 1 13 14 FLUX Centrifugal Immersion Pumps F 76 PP Size 135, 185, 3 and 35 in polypropylene for delivery rates of up to 74 m 3 /h FLUX Centrifugal Immersion Pumps F 716 PP and F 716 PVDF Size 1 and 135 in polypropylene or polyvinylidenfluoride for delivery rates of up to 1 m 3 /h CONSTRUCTION FEATURES IN DETAIL F 6 S-3 16 17 FLUX Centrifugal Immersion Pumps F 716 PP and F 716 PVDF Size 185 and 3 in polypropylene or polyvinylidenfluoride for delivery rates of up to 45 m 3 /h flexible coupling 18 19 FLUX Centrifugal Immersion Pumps F 76 PP and F 76 PVDF Size 1 and 135 in polypropylene or polyvinylidenfluoride for delivery rates of up to 1 m 3 /h 1 FLUX Centrifugal Immersion Pumps F 76 PP and F 76 PVDF Size 185 and 3 in polypropylene or polyvinlydenfluoride for delivery rates of up to 45 m 3 /h drive shaft inner tube 3 Dimensions of three-phase motors Questionnaire The great range of FLUX pumps outer tube mechanical seal open conical impeller 3 4
FLUX Performance chart FLUX F 6 S- and F 6 S-3 Dimensions F 6 S- and F 6 S-3 3 Three-phase motor: see page 5 1 5 3 Minimum liquid level when starting the pump. Also valid for variant 1. Measured values ± 1% determined with water ( C). Nominal speed n = 85 rpm Variant 1 In determining the absorbed kw of the motor, multiply the absorbed kw shown in the above diagram with the specific gravity of the liquid to be pumped. 1 max. 3 mm 4.1 4.
Type / Size F 6 S- F 6 S-3 Delivery rate Q max. 19 m 3 /h 3 m 3 /h Delivery head H max. 1 m water column 1 m water column Viscosity max. 5 mpas (cp) 5 mpas (cp) Temperature max. 1 C 1 C Seal type mechanical seal in ceramic oxide, o-rings in FPM shaft in stainless steel 1.4571/316 Ti, seal in FPM Impeller conical impeller in polypropylene (version in stainless steel on request) Pump housing Ø 14 mm Ø 14 mm 7 mm 6 3 1 61 3 1 1 mm 6 3 61 3 mm 6 3 3 61 3 3 Part numbers for immersion length 3 to 3 mm (in steps of 1 mm) on request. Accessories: Mounting flange in stainless steel 1.4571/316 Ti 947 14 5 outside Ø 65 mm, pitch circle Ø 5 mm, 8 bores Ø 18 mm each Suction strainer in stainless steel 1.4571/316 Ti 1 1 3 Hose connection in stainless steel, complete with nut in brass G 1 1 / (BSP 1 1 / female) for hose inside diameter DN 5 959 4 for hose inside diameter DN 3 959 4 3 for hose inside diameter DN 38 959 4 4 DRIVE MOTORS FOR CENTRIFUGAL IMMERSION PUMP F 6 S Three-phase motors protected to IP 55, with motor protection switch or cable terminal box FLUX CENTRIFUGAL IMMERSION PUMP F 6 S, THREAD ON OUTLET G 1 1 /4 A (BSP 1 1 / MALE), WITHOUT DRIVE MOTOR Capacity Voltage Frequency Nominal speed P Version with Version with motor protection switch cable terminal box,75 kw 3/4 V 5 Hz 85 rpm 1 46 1 6 1,1 kw 3/4 V 5 Hz 85 rpm 1 47 1 7 1,5 kw 3/4 V 5 Hz 85 rpm 1 48 1 8, kw 3/4 V 5 Hz 85 rpm 1 49 1 9 3, kw 4 V 5 Hz 85 rpm 1 5 1 1 4, kw 4 V 5 Hz 85 rpm 1 51 1 11 Three-phase motors explosion-proof to EEx e II T3 with cable terminal box Capacity Voltage Frequency Nominal speed P Three-phase motor Motor protection switch with cable terminal box EEx de II C T6 to be mounted on the carrying handle,75 kw 3/4 V 5 Hz 85 rpm 1 66 936 6 118 1,1 kw 3/4 V 5 Hz 85 rpm 1 67 936 6 118 1,5 kw 3/4 V 5 Hz 85 rpm 1 68 936 6 119, kw 3/4 V 5 Hz 85 rpm 1 69 936 6 119,5 kw 4 V 5 Hz 85 rpm 1 7 936 6 1 3,3 kw 4 V 5 Hz 85 rpm 1 71 936 6 1 CENTRIFUGAL IMMERSION PUMPS F 6 S FLUX CENTRIFUGAL IMMERSION PUMP F 64 PP IN POLYPROPYLENE SIZE, 3, Z AND 3 Z Typical applications Transferring low flammability liquids up to a viscosity of 5 mpas (cp) from containers, tanks, either open topped or closed. Transferring corrosive liquids in chemical processing and engineering, metal-working and electroplating together with water treatment and waste water treatment. Suitable for stationary or portable application. Construction features Vertical centrifugal immersion pump in polypropylene consisting of an inner tube and outer tube. The centrifugal impeller in the pump housing is driven by the motor via the drive shaft. The drive shaft is supported by intermediate bearings within the plastic sleeved steel inner tube, a mechanical seal separating the liquid from the bearings and upper shaft. This construction provides the ultimate in stability, preventing elongation of the plastic at high temperatures and ensures the maximum integrity of the mechanical seal. With an open conical impeller or a closed centrifugal impeller (Z). The liquid is delivered between the inner and outer tubes to the pump outlet. Three-phase motors in differing kw-ratings are available as a matched power unit. Connection to the pump is made via a flexible coupling. CONSTRUCTION FEATURES IN DETAIL flexible coupling drive shaft steel cored inner tube F 64 PP-3 Accessories: Carrying handle for three-phase motors up to 3, kw 1 1 54 Carrying handle for three-phase motors up 4, kw 1 1 531 Carrying handle for three-phase motors explosion-proof up to 3,3 kw 1 1 567 outer tube mechanical seal SCOPE OF SUPPLY A complete vertical centrifugal immersion pump consists of: drive motor, pump and necessary accessories. Weight per pump: 45 kg depending on the pump size, immersion length and motor kw. open conical impeller closed centrifugal impeller (Z) 5 6
FLUX Performance chart F 64 PP-, F 64 PP-3, F 64 PP- Z and F 64 PP-3 Z Dimensions F 64 PP-, F 64 PP-3, F 64 PP- Z and F 64 PP-3 Z 3Z Three-phase motor: see page 3 Z 3 3 3Z 1 Z 5 1 5 3 35 4 Minimum liquid level when starting the pump. Also valid for variant 1. Measured values ± 1% determined with water ( C). Nominal speed n = 85 rpm Variant 1 + 38 mm In determining the absorbed kw of the motor, multiply the absorbed kw shown in the above diagram with the specific gravity of the liquid to be pumped. 1 max. 4 mm 6.1 6.
Accessories: DRIVE MOTORS FOR CENTRIFUGAL IMMERSION PUMP F 64 PP Suction strainer in polypropylene 1 1 35 Hose connection in polypropylene, complete with nut G 1 /4 (BSP 1 /4 female) for hose inside diameter DN 3 959 4 98 for hose inside diameter DN 38 959 4 99 for hose inside diameter DN 5 959 4 1 Three-phase motors protected to IP 55, with motor protection switch or cable terminal box FLUX CENTRIFUGAL IMMERSION PUMP F 64 PP, THREAD ON OUTLET G 1 /4 A (BSP 1 /4 MALE), WITHOUT DRIVE MOTOR Type / Size F 64 PP- F 64 PP-3 F 64 PP-Z F 64 PP-3Z Delivery rate Q max. 17 m 3 /h 9 m 3 /h 1 m 3 /h 34 m 3 /h Delivery head H max. 8 m water column 1 m water column 1 m water column 11 m water column Viscosity max. 5 mpas (cp) 5 mpas (cp) mpas (cp) mpas (cp) Temperature max. 5 C 5 C 5 C 5 C Seal type mechanical seal in ceramic oxide / SiC, o-rings in FPM shaft in Hastelloy C, seals in FPM Impeller open conical impeller in PP closed centrifugal impeller in PP Pump housing Ø 148 mm Ø 148 mm Ø 148 mm Ø 148 mm Mounting flange* outside Ø 65 mm, pitch circle Ø 5 mm, 8 bores Ø 18 mm each 7 mm 64 41 47 64 41 67 64 41 57 64 41 77 1 mm 64 41 41 64 41 61 64 41 51 64 41 71 mm 64 41 4 64 41 6 64 41 5 64 41 7 Part numbers for immersion length 4 to 4 mm (in steps of 1 mm) on request. *also available without mounting flange for portable application. Capacity Voltage Frequency Nominal speed P Version with Version with motor protection switch cable terminal box,75 kw 3/4 V 5 Hz 85 rpm 1 46 1 6 1,1 kw 3/4 V 5 Hz 85 rpm 1 47 1 7 1,5 kw 3/4 V 5 Hz 85 rpm 1 48 1 8, kw 3/4 V 5 Hz 85 rpm 1 49 1 9 3, kw 4 V 5 Hz 85 rpm 1 5 1 1 4, kw 4 V 5 Hz 85 rpm 1 51 1 11 Three-phase motors explosion-proof to EEx e II T3 with cable terminal box Capacity Voltage Frequency Nominal speed P Version with Motor protection switch cable terminal box EEx de II C T6 to be mounted on the carrying handle,75 kw 3/4 V 5 Hz 85 rpm 1 66 936 6 118 1,1 kw 3/4 V 5 Hz 85 rpm 1 67 936 6 118 1,5 kw 3/4 V 5 Hz 85 rpm 1 68 936 6 119, kw 3/4 V 5 Hz 85 rpm 1 69 936 6 119,5 kw 4 V 5 Hz 85 rpm 1 7 936 6 1 3,3 kw 4 V 5 Hz 85 rpm 1 71 936 6 1 CENTRIFUGAL IMMERSION PUMP F 64 PP FLUX CENTRIFUGAL IMMERSION PUMP F 64 PP AND F 64 PVDF IN POLYPROPYLENE OR POLYVINYLIDENFLUORIDE SIZE 185 Typical applications Transferring low flammability liquids up to a viscosity of 5 mpas (cp) from containers, tanks, either open topped or closed. Transferring corrosive liquids in chemical processing and engineering, metal-working and electroplating together with water treatment and waste water treatment. Suitable for stationary or portable application. Construction features Vertical centrifugal immersion pump for stationary application. The centrifugal impeller in the pump housing is driven by the motor via the drive shaft. The drive shaft is supported by intermediate bearings within the plastic sleeved steel inner tube, a mechanical seal separating the liquid from the bearings and upper shaft. This construction provides the ultimate in stability, preventing elongation of the plastic at high temperatures and ensures the maximum integrity of the mechanical seal. This pump design does not have a separate discharge tube. Immediately after the pump housing the liquid is fed back into the outer tube and delivered to the outlet connection between the inner and outer tubes. A range of carefully chosen impeller diameters, together with a range of three-phase motors in differing kw-ratings, ensures the optimum selection of pumps to meet the specific operating requirements. Connection of pump and motor is made via a flexible coupling. CONSTRUCTION FEATURES IN DETAIL flexible coupling outer tube steel cored inner tube pump shaft NEW F 64 PP-185 Accessories: Carrying handle for three-phase motors up to 3, kw 1 1 54 Carrying handle for three-phase motors up 4, kw 1 1 531 Carrying handle for three-phase motors explosion-proof up to 3,3 kw 1 1 567 SCOPE OF SUPPLY A complete vertical centrifugal immersion pump consists of: drive motor, pump and necessary accessories. Weight per pump: - 6 kg depending on the pump size, immersion length and motor kw. mechanical seal centrifugal impeller in differing diameters spiral housing cover with circlip 7 8
FLUX Performance chart F 64 PP-185 and F 64 PVDF-185 Dimensions F 64 PP-185 and F 64 PVDF-185 Ø 14 Ø 13 Ø 1 Ø 11 Ø 1 Ø 14 Three-phase motor: see page Minimum liquid level when starting the pump. Also valid for the variants 1, and 3 Ø 13 Ø 1 Ø 11 Ø 1 1 3 4 5 Measured values ± 1% determined with water ( C). Nominal speed n = 85 min- 1 Variant 1 Variant Variant 3 and suction strainer In order to achieve the desired output, centrifugal impellers in diameters of 1 to 14 mm are available. 1 3 In determining the absorbed kw of the motor, multiply the absorbed kw shown in the above diagram with the specific gravity of the liquid to be pumped. max. 4 mm Dimension p max. mm 8.1 8.
FLUX CENTRIFUGAL IMMERSION PUMP F 64 PP IN POLYPROPYLENE AND F 64 PVDF IN POLYVINYLIDENFLUORIDE, THREAD ON OUTLET G 1 /4 A (BSP 1 /4 MALE), WITHOUT DRIVE MOTOR Type / Size F 64 PP-185 F 64 PVDF-185 Delivery rate Q max. 4 m 3 /h 4 m 3 /h Delivery head H max. 3 m water column 3 m water column Viscosity max. mpas (cp) mpas (cp) Temperature max. 6 C 8 C Seal type mechanical seal in ceramic oxide /SiC, o-rings in FPM shaft in Hastelloy C, seals in FPM Centrifugal impeller Ø 1 14 mm in PP or PVDF Pump housing Ø 49 mm Ø 49 mm Mounting flange outside Ø 34 mm, pitch circle Ø 95 mm, 4 bores Ø mm each 1 mm 64 41 1 64 61 1 mm 64 41 64 61 mm 64 41 64 61 Part numbers for immersion length 4 to 4 mm (in steps of 1 mm) on request. Accessories: Extension tube in PP or PVDF in steps of 1 mm. Dimension p up to max. mm Suction strainer in PP or PVDF welded onto the cover of the pump housing or onto the extension tube Hose connection in polypropylene, complete with nut G 1 /4 (BSP 1 /4 female) for hose inside diameter DN 3 959 4 98 for hose inside diameter DN 38 959 4 99 for hose inside diameter DN 5 959 4 1 Hose connection in polyvinylidenfluoride, complete with nut G 1 /4 (BSP 1 /4 female) for hose inside diameter DN 3 959 4 14 for hose inside diameter DN 38 959 4 for hose inside diameter DN 5 959 4 96 DRIVE MOTORS FOR CENTRIFUGAL IMMERSION PUMPS F 64 PP AND F 64 PVDF Three-phase motors protected to IP 55, with motor protection switch or cable terminal box Capacity Voltage Frequency Nominal speed P Version with Version with motor protection switch cable terminal box,75 kw 3/4 V 5 Hz 85 rpm 1 46 1 6 1,1 kw 3/4 V 5 Hz 85 rpm 1 47 1 7 1,5 kw 3/4 V 5 Hz 85 rpm 1 48 1 8, kw 3/4 V 5 Hz 85 rpm 1 49 1 9 3, kw 4 V 5 Hz 85 rpm 1 5 1 1 4, kw 4 V 5 Hz 85 rpm 1 51 1 11 Three-phase motors explosion-proof to EEx e II T3 with cable terminal box Capacity Voltage Frequency Nominal speed P Version with Motor protection switch cable terminal box EEx de II C T6 to be mounted on the carrying handle,75 kw 3/4 V 5 Hz 85 rpm 1 66 936 6 118 1,1 kw 3/4 V 5 Hz 85 rpm 1 67 936 6 118 1,5 kw 3/4 V 5 Hz 85 rpm 1 68 936 6 119, kw 3/4 V 5 Hz 85 rpm 1 69 936 6 119,5 kw 4 V 5 Hz 85 rpm 1 7 936 6 1 3,3 kw 4 V 5 Hz 85 rpm 1 71 936 6 1 SCOPE OF SUPPLY A complete vertical centrifugal immersion pump consists of: drive motor, pump with mounting flange and necessary accessories. Weight per pump: 6 kg depending on the pump size, immersion length and motor kw. CENTRIFUGAL IMMERSION PUMP F 64 PP AND F 64 PVDF FLUX CENTRIFUGAL PUMPS F 6 S TR AND F 64 PP TR IN HORIZONTAL VERSION Typical applications Transferring low flammability liquids up to a viscosity of 5 mpas (cp) from containers or tanks, either open topped or closed. The pump is used either horizontally mounted onto a base plate or fixed vertically. Construction features Centrifugal pump in horizontal version in stainless steel or polypropylene, consisting of an inner tube and outer tube. The centrifugal impeller in the pump housing is driven by the motor via the drive shaft The drive shaft is supported by intermediate bearings within inner tube, a mechanical seal separates the liquid from the bearings and upper shaft. The PP version has a steel cored PP inner tube. This construction provides the ultimate in stability, preventing elongation of the plastic at high temperatures and ensures the maximum integrity of the mechanical seal. With an open conical impeller or a closed centrifugal impeller (Z) Depending on the model, suction and discharge sides are fitted with threaded or flanged connections. Three-phase motors in differing kw-ratings are available as a matched power unit. Connection to the pump is made via a flexible coupling. F 6 S-3 TR mounted on base plate F 64 PP-3 TR mounted on base plate F 64 PP-3 TR mounted on base plate 9 1
FLUX Performance chart F 6 S-3 TR, Dimensions F 6 S-3 TR with thread connection Three-phase motor: see page 3 3 Dimensions F 64 PP-3 TR with thread connection 5 1 5 Three-phase motor: see page Performance chart F 64 PP-3 TR, 3 3 3 1 Dimensions F 64 PP-3 TR with flange connection Three-phase motor: see page 5 1 5 3 35 4 Performance chart F 64 PP-3 TR 4 35 Ø16 3 Ø 5 Ø 14 Ø13 Dimensions F 64 PP-3 TR with flange connection 1 Ø1 Ø 11 Ø 1 Ø 16 Ø Ø 14 Ø13 3 Three-phase motor: see page 5 Ø 11 Ø 1 Ø1 1 5 1 5 3 35 4 45 Measured values ± 1% determined with water ( C). Nominal speed n = 85 rpm In determining the absorbed kw of the motor, multiply the absorbed kw shown in the above diagram with the specific gravity of the liquid to be pumped. 1.1 1.
FLUX CENTRIFUGAL PUMP F 6 S TR IN STAINLESS STEEL, WITHOUT DRIVE MOTOR Type / Size F 6 S-3 TR Delivery rate Q max. 3 m 3 /h Delivery head H max. 1 m water column Viscosity max. 5 mpas (cp) Temperature max. 1 C Seal type mechanical seal in ceramic oxide, o-rings in FPM shaft in stainless steel 1.4571/316 Ti, seals in FPM Impeller open conical impeller in polypropylene (version in stainless steel on request) Suction side thread G A (BSP male) Discharge side thread G 1 1 / A (BSP 1 1 / male) 6 5 5 Accessoires: Base plate in aluminium alloy 1 Hose connection in stainless steel, complete with nut G 1 1 / (BSP 1 1 / female) for hose inside diameter DN 5 959 4 for hose inside diameter DN 3 959 4 3 for hose inside diameter DN 38 959 4 4 CENTRIFUGAL PUMP F 64 PP TR IN POLYPROPYLENE, WITHOUT DRIVE MOTOR Type / Size F 64 PP-3 TR Delivery rate Q max. 9 m 3 /h Delivery head H max. 1 m water column Viscosity max. 5 mpas (cp) Temperature max. 5 C Seal type mechanical seal in ceramic oxide /SiC, o-rings in FPM shaft in Hastelloy C, seals in FPM Impeller open conical impeller in PP Suction side thread G A (BSP male) flange DN 65, PN 1 Discharge side thread G 1 /4 A (BSP 1 /4 male) flange DN 5, PN 1 64 41 61 64 41 6 CENTRIFUGAL PUMP F 64 PP TR IN POLYPROPYLENE, WITHOUT DRIVE MOTOR Type / Size F 64 PP-3 TR Delivery rate Q max. 44 m 3 /h Delivery head H max. 33 m water column Viscosity max. mpas (cp) Temperature max. 6 C Seal material mechanical seal in ceramic oxide/sic, o-rings in FPM shaft in Hastelloy C, seals in FPM Impeller Ø 1 16 mm in PP Suction side flange DN 65, PN 1; outside Ø 185 mm, p.c.ø 145 mm, 4 bores Ø 18 mm each Discharge side flange DN 5, PN 1; outside Ø 165 mm, p.c.ø mm, 4 bores Ø 18 mm each 64 41 3 Accessories: Base plate in aluminium alloy for F 64 PP-3 TR 1 1 Base plate in polypropylene for F 64 PP-3 TR and F 64 PP-3 TR 1 3 Hose connection in polypropylene, complete with nut G 1 /4 (BSP 1 /4 female) for hose inside diameter DN 3 959 4 98 for hose inside diameter DN 38 959 4 99 for hose inside diameter DN 5 959 4 1 Drive motors see page 9 CENTRIFUGAL PUMPS IN HORIZONTAL VERSION FLUX CENTRIFUGAL IMMERSION PUMP F 76 PP IN POLYPROPYLENE SIZE 135, 185, 3 AND 35 Typical applications Transfer of corrosive liquids in the chemical industry and all aspects of chemical engineering together with any application that requires the safe and economical transfer, or circulation, of acids and alkalis or other chemical fluids, with or without solids in suspension. Construction features Vertical centrifugal immersion pump for stationary application. The robust pump housing is solidly welded to the support tube. A sleeve bearing, which is lubricated by the liquid, allows immersion lengths of up to 1 mm, and on the pump size 3, with additional intermediate bearings, even up to mm. A large polpypropylene-coated drive shaft together with the use of a thick-walled support tube ensures a very smooth running pump. This type of construction prevents the rotating components from coming to contact with the pump housing and guarantees a long service life and extended maintenance intervals, even in the case of continuous use. A range of carefully chosen impeller diameters, together with a range of three-phase motors in differing kw-ratings, ensures the optimum selection of pumps to meet the specific operating requirements. Connection of pump and motor is made via a flexible coupling. CONSTRUCTION FEATURES IN DETAIL flexible coupling large pump shaft with protective coating in PP slide bearing lubricated by the liquid wearing bushing in HC F 76 PP-35 SCOPE OF SUPPLY A complete centrifugal pump in horizontal version consists of drive motor, pump and base plate. Weight per pump including base plate: 9 5 kg depending on pump size and motor kw. centrifugal impeller in differing diameters cover with circlip on pump size 185 and 3 11 1
Performance chart F 76 PP-135 18 16 Ø1 14 Ø9 1 1 Ø8 8.8 Ø1 6.6 Ø9 4 Ø8.4.. 1 3 4 5 6 7 8 9 1 11 1 13 Performance chart F 76 PP-185 5 Ø 14 Ø 13 Ø 1 Measured values ± 1% determined with water ( C). Nominal speed n = 85 rpm In order to obtain the desired output, centrifugal impellers in differing diameters are available. In determining the absorbed kw of the motor, multiply the absorbed kw shown in the above diagram with the specific gravity of the liquid to be pumped. Dimensions F 76 PP-135 Three-phase motors: see page Dimensions F 76 PP-185 FLUX Variant 1 Variant Variant 3 and suction strainer 1 3 1 3 Ø 11 1 Ø 1 5 Ø 1 Ø 11 Ø 1 Ø 14 Ø13 5 1 5 3 35 4 45 3 1 max. 1 mm Dimension p max. 1 mm max. 1 mm Dimension p max. mm Performance chart F 76 PP-3 4 35 Ø 16 Dimensions F 76 PP-3 Dimensions F 76 PP-35 3 Ø 5 1 Ø 14 Ø13 Ø 16 Ø Ø 14 Ø 13 4 3 Three-phase motors: see page Minimum or maximum liquid level when starting the pump. Also valid for the variants 1, and 3 5 1 5 1 5 3 35 4 45 Performance chart F 76 PP-35 5 Ø 5 Ø 4 Ø 3 Ø Ø 1 Ø Nominal speed n = 145 rpm 1 3 1 3 1 Ø 5 Ø4 Ø 3 Ø Ø1 Ø 4 3 5 1 3 4 5 6 7 8 1 max. mm Dimension p max. mm max. 1 mm Dimension p max. mm 1.1 1.
Accessories: Extension tube in PP in steps of 1 mm. Dimension p up to max. 1 mm at size 135 and up to mm at sizes 185, 3 and 35. Suction strainer in PP welded onto the cover of the pump housing or onto the extension tube. DRIVE MOTORS FOR CENTRIFUGAL IMMERSION PUMP F 76 PP Three-phase motors protected to IP 55, with cable terminable box FLUX CENTRIFUGAL IMMERSION PUMP F 76 PP IN POLYPROPYLENE, VERSION WITH SUPPORT TUBE, WITHOUT DRIVE MOTOR Type / Size F 76 PP-135 F 76 PP-185 F 76 PP-3 F 76 PP-35 Delivery rate Q max. 1 m 3 /h 43 m 3 /h 44 m 3 /h 74 m 3 /h Delivery head H max. m water column 3 m water column 33 m water column 3 m water column Viscosity max. mpas (cp) mpas (cp) mpas (cp) mpas (cp) Temperature max. 6 C 6 C 6 C 6 C Seal material no seals in contact with the liquid shaft in stainless steel 1.4571/316 Ti with protective coating in PP, slide bearing in hard carbon or fluorosint Centrifugal Impeller in PP Ø 8 1 mm Ø 1 14 mm Ø 13 16 mm Ø 5 mm Pump housing Ø 174 mm Ø 49 mm Ø 64 mm Ø 417 mm Mounting flange in PP outside Ø 5 mm outside Ø 34 mm outside Ø 34 mm outside Ø 5 mm Thread on outlet G 1 1 / A (BSP 1 1 / male) G 1 /4 A (BSP 1 /4 male) G 1 /4 A (BSP 1 /4 male) G 3 /4 A (BSP 3 /4 male) Motor capacity P,37,75 kw 1,5 4, kw 3, 5,5 kw 3, 5,5 kw n = 85 rpm n = 85 rpm n = 85 rpm n = 145 rpm 5 mm 76 41 76 41 5 76 41 35 76 41 45 7 mm 76 41 17 76 41 7 76 41 37 76 41 47 1 mm 76 41 11 76 41 1 76 41 31 76 41 41 Capacity P Flange Ø Voltage Frequency Nominal speed,37 kw 1 mm 3/4 V 5 Hz n = 85 rpm 1 4,55 kw 1 mm 3/4 V 5 Hz n = 85 rpm 1 5,75 kw 1 mm 3/4 V 5 Hz n = 85 rpm 1 19 1,5 kw 16 mm 3/4 V 5 Hz n = 85 rpm 1 8, kw 16 mm 3/4 V 5 Hz n = 85 rpm 1 9 3, kw 16 mm 4 V 5 Hz n = 85 rpm 1 1 4, kw 16 mm 4 V 5 Hz n = 85 rpm 1 11 5,5 kw 16 mm 4 V 5 Hz n = 85 rpm 1 3, kw 16 mm 4 V 5 Hz n = 145 rpm 1 53 4, kw 16 mm 4 V 5 Hz n = 145 rpm 1 511 5,5 kw 16 mm 4 V 5 Hz n = 145 rpm 1 53 Three-phase motors explosion-proof to EEx e II T3 with terminal box on request. SCOPE OF SUPPLY A complete vertical centrifugal immersion pump consists of: drive motor, pump with mounting flange and necessary accessories. Weight per pump F 76 PP: 13 85 kg depending on the pump size, immersion length and motor kw. CENTRIFUGAL IMMERSION PUMP F 76 PP FLUX CENTRIFUGAL IMMERSION PUMP F 716 PP AND F 716 PVDF IN POLYPROPYLENE OR POLYVINYLIDENFLUORIDE SIZE 1 AND 135 Typical applications Transferring and circulating of neutral or corrosive liquids in the chemical industry and chemical engineering, electroplating industry, steel or stainless steel pickling plants, flue gas decontamination, exhaust air purification, water and waste water treatment. Construction features Vertical centrifugal immersion pump for stationary application. With a compact design requiring very little head room above the mounting flange. This design uses a three-phase motor with extended shaft, especially allowing the pump to use the motor shaft. All wetted parts are made in PP or PVDF. The robust support tube (bars) solidly connected to the mounting flange ensures a very smooth running, prevents the rotating elements from making contact with the pump housing and guarantees a very long service life, even in case of continuous use. As neither bearings nor seals are in contact with the liquid, the pump is very F 716 PP1-1 wear-resistant and suitable for dry running operation. The immersion length of the pump can be extended, up to 1 mm maximum, by the suction tube option. A suction strainer welded onto the cover of the pump housing or onto the extension tube protects the pump against the ingress of coarse impurities. A range of carefully chosen impeller diameters, together with a range of three-phase motors in differing kw-ratings, ensures the optimum selection of pumps to meet the specific operating requirements. CONSTRUCTION FEATURES IN DETAIL integral three-phase motor seal kit prevents vapours entering the motor area motor shaft = pump shaft with protective coating in PP or PVDF F 716 PVDF-135 version with support tube for temperatures up to 6 C version with support bars for temperatures up to 8 C (PP) or 1 C (PVDF) centrifugal impeller in differing diameters 13 14
Performance chart F 716 PP1-1, F 716 PP-1 and F 716 PVDF-1 1 Dimensions F 716 PP1-1 Version with support tube FLUX Dimensions F 716 PP-1 and F 716 PVDF-1 Version with support bars Ø8 8 6 4 Ø7 Ø6 Ø5 Ø5 Ø6 Ø7 Ø8.4.3..1 Three-phase motors: see page Variant 1 Variant Variant 3 and suction strainer 1 3 1 3 1 3 4 5 6 7 8. Measured values ± 1% determined with water ( C). Nominal speed n = 85 rpm In order to obtain the desired output, centrifugal impellers in differing diameters are available. max. 4 mm Dimension p max. 1 mm max. 5 mm Dimension p max. 1 mm In determining the absorbed kw of the motor, multiply the absorbed kw shown in the above diagram with the specific gravity of the liquid to be pumped. Dimensions F 716 PP1-135 Version with support tube Dimensions F 716 PP-135 and F 716 PVDF-135 Version with support bars Performance chart F 716 PP1-135, F 716 PP-135 and F 716 PVDF-135 18 Three-phase motors: see page Minimum or maximum liquid level when starting the pump. Also valid for the variants 1, and 3 16 Ø1 14 1 1 Ø9 Ø8 1 3 1 3 8.8 6 4 Ø8 Ø9 Ø1.6.4 1 3 4 5 6 7 8 9 1 11 1 13.. max. 4 mm Dimension p max. 1 mm max. 5 mm Dimension p max. 1 mm 14.1 14.
CENTRIFUGAL IMMERSION PUMP F 716 PP IN POLYPROPYLENE, WITH INTEGRAL THREE-PHASE MOTOR FLUX Type / Size F 716 PP1-1 F 716 PP-1 F 716 PP1-135 F 716 PP-135 Version with support tube with support bars with support tube with support bars Delivery rate Q max. 8 m 3 /h 8 m 3 /h 1 m 3 /h 1 m 3 /h Delivery head H max. 8 m water column 8 m water column m water column m water column Viscosity max. mpas (cp) mpas (cp) mpas (cp) mpas (cp) Temperature max. 6 C 8 C 6 C 8 C Seal material no bearings nor seals in contact with the liquid shaft in stainless steel 1.4571/316 Ti with protective coating in PP Centrifugal impeller in PP Ø 5 8 mm Ø 5 8 mm Ø 8 1 mm Ø 8 1 mm Pump housing Ø mm Ø mm Ø 174 mm Ø 174 mm Mounting flange in PP outside Ø 5 mm outside Ø 5 mm outside Ø 5 mm outside Ø 5 mm Thread on outlet G 1 1 /4 A (BSP 1 1 /4 male) G 1 1 /4 A (BSP 1 1 /4 male) G 1 1 / A (BSP 1 1 / male) G 1 1 / A (BSP 1 1 / male) Motor capacity P,37 kw,37 kw,37 kw,37 kw 3 mm 716 41 3 716 4 3 716 41 13 716 4 13 4 mm 716 41 4 716 4 4 716 41 14 716 4 14 5 mm 716 4 5 716 4 Motor capacity P,55 kw,55 kw,55 kw,55 kw 3 mm 716 41 13 716 4 13 716 41 113 716 4 113 4 mm 716 41 14 716 4 14 716 41 114 716 4 114 5 mm 716 4 716 4 1 Motor capacity P,75 kw,75 kw,75 kw,75 kw 3 mm 716 41 13 716 4 13 4 mm 716 41 14 716 4 14 5 mm 716 4 CENTRIFUGAL IMMERSION PUMP F 716 PVDF IN POLYVINYLIDENFLUORIDE, WITH INTEGRAL THREE-PHASE MOTOR Type / Size F 716 PVDF-1 F 716 PVDF-135 Version with support bars with support bars Delivery rate Q max. 8 m 3 /h 1 m 3 /h Delivery head H max. 8 m water column m water column Viscosity max. mpas (cp) mpas (cp) Temperature max. 1 C 1 C Seal material no bearings nor seals in contact with the liquid shaft in stainless steel 1.4571/316 Ti with protective coating in PVDF Centrifugal impeller in PVDF Ø 5 8 mm Ø 8 1 mm Pump housing Ø mm Ø 174 mm Mounting flange in PVDF outside Ø 45 mm outside Ø 45 mm Thread on outlet G 1 1 /4 A (BSP 1 1 /4 male) G 1 1 / A (BSP 1 1 / male) Motor capacity P,37 kw,55 kw,37 kw,55 kw,75 kw 3 mm 716 6 3 716 6 13 716 6 13 716 6 113 716 6 13 4 mm 716 6 4 716 6 14 716 6 14 716 6 114 716 6 14 5 mm 716 6 5 716 6 716 6 716 6 1 716 6 Accessories: Extension tube in PP or PVDF in steps of 1 mm. Dimension p up to max. 1 mm. Suction strainer in PP or PVDF welded at the cover of the pump housing or at the extension tube. SCOPE OF SUPPLY A complete vertical centrifugal immersion pump consists of: pump with mounting flange and integral three-phase motor and necessary accessories. Weight per pump: 9 kg depending on the pump size, immersion length and motor kw. CENTRIFUGAL IMMERSION PUMP F 716 PP AND F 716 PVDF FLUX CENTRIFUGAL IMMERSION PUMP F 716 PP AND F 716 PVDF IN POLYPROPYLENE OR POLYVINYLIDENFLUORIDE SIZE 185 AND 3 Typical applications Transferring and circulating of neutral or corrosive liquids in the chemical industry and chemical engineering, electroplating industry, steel or stainless steel pickling plants, flue gas decontamination, exhaust air purification, water and waste water treatment. Construction features Vertical centrifugal immersion pump for stationary application. With a compact design requiring very little head room above the mounting flange. This design uses a three-phase motor with extended shaft, allowing the pump to use the motor shaft. All wetted parts are made in PP or PVDF. The robust support tube (bars) solidly connected to the mounting flange ensures a very smooth running, prevents the rotating elements from making contact with the pump housing and guarantees F 716 PP1-185 a very long service life, even in case of continuous use. As neither bearings nor seals are in contact with the liquid, the pump is very wear-resistant and suitable for dry running operation. The immersion length of the pump can be extended, up to mm maximum, by the suction tube option. A suction strainer welded onto the cover of the pump housing or onto the extension tube protects the pump against the ingress of coarse impurities. A range of carefully chosen impeller diameters, together with a range of three-phase motors in differing kw-ratings, ensures the optimum selection of pumps to meet the specific operating requirements. CONSTRUCTION FEATURES IN DETAIL integral three-phase motor seal kit prevents vapours entering the motor area motor shaft = pump shaft with protective coating in PP or PVDF version with support tube for temperatures up to 6 C version with support bar for temperatures up to 8 C (PP) or 1 C (PVDF) centrifugal impeller in differing diameters cover with circlip on pump size 185 F 716 PVDF-3 16
Performance chart F 716 PP1-85, F 716 PP-185 and F 716 PVDF-185 5 Ø 14 Dimensions F 716 PP1-185 Version with support tube FLUX Dimensions F 716 PP-185 and F 716 PVDF-185 Version with support bars Ø 13 Ø 1 Ø 11 Three-phase motors: see page Variant 1 Variant 1 Ø 1 Variant 3 and suction strainer 5 Ø 1 Ø 13 Ø 1 Ø 11 Ø 14 3 1 1 3 1 3 5 1 5 3 35 4 max. 5 mm Dimension p max. mm max. 5 mm Dimension p max. mm Measured values ± 1% determined with water ( C). Nominal speed n = 85 min-1 In order to obtain the desired output, centrifugal impellers in differing diameters are available. In determining the absorbed kw of the motor, multiply the absorbed kw shown in the above diagram with the specific gravity of the liquid to be pumped. Dimensions F 716 PP1-3 Version with support tube Dimensions F 716 PP-3 and F 716 PVDF-3 Version with support bars Performance chart F 716 PP1-3, F 716 PP-3 and F 716 PVDF-3 35 Ø 16 3 Ø Three-phase motors: see page Minimum or maximum liquid level when starting the pump. Also valid for the variants 1, and 3 5 Ø 14 1 3 1 3 Ø 13 1 5 Ø 14 Ø13 Ø 16 Ø 6 4 max. 5 mm Dimension p max. mm max. 5 mm Dimension p max. mm 5 1 5 3 35 4 45 5 16.1 16.
CENTRIFUGAL IMMERSION PUMP F 716 PP IN POLYPROPYLENE, WITH INTEGRAL THREE-PHASE MOTOR Accessories: Extension tube in PP or PVDF in steps of 1 mm. Dimension p up to max. mm. Suction strainer in PP or PVDF welded onto the cover of the pump housing or onto the extension tube. Weight per pump: 5 kg depending on the pump size, immersion length and motor kw. FLUX Type / Size F 716 PP1-185 F 716 PP-185 F 716 PP1-3 F 716 PP-3 Version with support tube with support bars with support tube with support bars Delivery rate Q max. 38 m 3 /h 38 m 3 /h 45 m 3 /h 45 m 3 /h Delivery head H max. 3 m water column 3 m water column 35 m water column 35 m water column Viscosity max. mpas (cp) mpas (cp) mpas (cp) mpas (cp) Temperature max. 6 C 8 C 6 C 8 C Seal material no bearings nor seals in contact with the liquid shaft in stainless steel 1.4571/316 Ti with protective coating in PP Centrifugal impeller in PP Ø 1 14 mm Ø 1 14 mm Ø 13 16 mm Ø 13 16 mm Pump housing Ø 49 mm Ø 49 mm Ø 64 mm Ø 64 mm Mounting flange in PP outside Ø 34 mm outside Ø 34 mm outside Ø 34 mm outside Ø 34 mm Thread on outlet G 1 /4 A (BSP 1 /4 male) G 1 /4 A (BSP 1 /4 male) G 1 /4 A (BSP 1 /4 male) G 1 /4 A (BSP 1 /4 male) Motor capacity P 1,5 kw 1,5 kw 3, kw 3, kw 3 mm 716 41 3 716 4 3 716 41 33 716 4 33 4 mm 716 41 4 716 4 4 716 41 34 716 4 34 5 mm 716 41 5 716 4 5 716 41 35 716 4 35 Motor capacity P, kw, kw 4, kw 4, kw 3 mm 716 41 13 716 4 13 716 41 313 716 4 313 4 mm 716 41 14 716 4 14 716 41 314 716 4 314 5 mm 716 41 716 4 716 41 3 716 4 3 Motor capacity P 3, kw 3, kw 5,5 kw 5,5 kw 3 mm 716 41 3 716 4 3 716 41 33 716 4 33 4 mm 716 41 4 716 4 4 716 41 34 716 4 34 5 mm 716 41 5 716 4 5 716 41 35 716 4 35 Motor capacity P 4, kw 4, kw 3 mm 716 41 33 716 4 33 4 mm 716 41 34 716 4 34 5 mm 716 41 35 716 4 35 CENTRIFUGAL IMMERSION PUMP F 716 PVDF IN POLYVINYLIDENFLUORIDE, WITH INTEGRAL THREE-PHASE MOTOR Type / Size F 716 PVDF-185 F 716 PVDF-3 Version with support bars with support bars Delivery rate Q max. 38 m 3 /h 45 m 3 /h Delivery head H max. 3 m water column 35 m water column Viscosity max. mpas (cp) mpas (cp) Temperature max. 1 C 1 C Seal material no bearings nor seals in contact with the liquid shaft in stainless steel 1.4571/316 Ti with protective coating in PVDF Centrifugal impeller in PVDF Ø 1 14 mm Ø 13 16 mm Pump housing Ø 49 mm Ø 64 mm Mounting flange in RCH1 outer Ø 34 mm outer Ø 34 mm Thread on outlet G 1 /4 A G 1 /4 A Motor capacity P 1,5 kw, kw 3, kw 4, kw 3 mm 716 6 3 716 6 13 716 6 33 716 6 313 4 mm 716 6 4 716 6 14 716 6 34 716 6 314 5 mm 716 6 5 716 6 716 6 35 716 6 3 Puissance de moteur P 3, kw 4, kw 5,5 kw 3 mm 716 6 3 716 6 33 716 6 33 4 mm 716 6 4 716 6 34 716 6 34 5 mm 716 6 5 716 6 35 716 6 35 CENTRIFUGAL IMMERSION PUMP F 716 PP AND F 716 PVDF 17 18 FLUX CENTRIFUGAL IMMERSION PUMP F 76 PP AND F 76 PVDF IN POLYPROPYLENE OR POLYVINYLIDENFLUORIDE SIZE 1 AND 135 Typical applications Transferring and circulating of neutral or corrosive liquids in the whole field of the chemical industry and chemical engineering, electroplating industry, steel or stainless steel pickling plants, flue gas decontamination, exhaust air purification, water and waste-water treatment. Construction features Vertical centrifugal immersion pump for stationary application. The robust pump shaft is mounted in an upper pedestal and supported by two antifriction bearings. This construction, with the bearings spaced along the pedestal, ensures that any radial or axial forces are absorbed, even under heavy load. The result is a very smooth running pump. The solid version with support bars prevents the rotating elements from making contact with the pump housing and guarantees a very long service life, even in continuous use applications. As neither bearing nor seals are in contact with the liquid, the pump is very wear-resistant and suitable for dry running operation. The immersion length of the pump can be extended, up to 1 mm maximum, by the suction tube option. A suction strainer welded onto the cover of the pump housing or onto the extension tube protects the pump against the ingress of coarse impurities. A range of carefully chosen impeller diameters, together with a range of three-phase motors in differing kw-ratings, ensures the optimum selection of pumps to meet the specific operating requirements. CONSTRUCTION FEATURES IN DETAIL antifriction bearings located in a pedestal seal kit prevents vapours entering the pedestal robust pump shaft with protective coating in PP or PVDF version with support bars for temperatures up to 8 C (PP) or 1 C (PVDF) centrifugal impeller in differing diameters F 76 PP-1 F 76 PVDF-135
FLUX Performance chart F 76 PP-1 and F 76 PVDF-1 Dimensions F 76 PP-1 and F 76 PVDF-1 1 Ø8 8 Ø7 Three-phase motors: see page 6 4 Ø6.4 max. 5 mm Ø8 Ø5 Ø7 Ø6 Ø5 1 3 4 5 6 7 8.3..1. 1 3 Variant 1 dimension p max. 1 mm Variant Variant 3 and suction strainer Measured values ± 1% determined with water ( C). Nominal speed n = 85 rpm In order to achieve the desired output, centrifugal impellers in differing diameters are available. In determining the absorbed kw of the motor, multiply the absorbed kw shown in the above diagram with the specific gravity of the liquid to be pumped. Dimensions F 76 PP-135 and F 76 PVDF-135 Minimum or maximum liquid level when starting the pump. Also valid for the variants 1, and 3 Performance chart F 76 PP-135 and F 76 PVDF-135 Three-phase motors: see page 18 16 Ø1 max. 5 mm 14 1 Ø9 Variant 1 dimension p max. 1 mm 1 8 6 4 Ø8 Ø8 Ø9 Ø1.8.6.4 1 3 Variant Variant 3 and suction strainer. 1 3 4 5 6 7 8 9 1 11 1 13. 18.1 18.
Accessories: Extension tube in PP or PVDF in steps of 1 mm. Dimension p up to. max. 1 mm. Suction strainer in PP or PVDF welded onto the cover of the pump housing or onto the extension tube. FLUX CENTRIFUGAL IMMERSION PUMP F 76 PP IN POLYPROPYLENE AND F 76 PVDF IN POLYVINYLIDENFLUORIDE, VERSION WITH SUPPORT BARS, WITHOUT DRIVE MOTOR Type / Size F 76 PP-1 F 76 PP-135 F 76 PVDF-1 F 76 PVDF-135 Delivery rate Q max. 8 m 3 /h 1 m 3 /h 8 m 3 /h 1 m 3 /h Delivery head H max. 8 m water column m water column 8 m water column m water column Viscosity max. mpas (cp) mpas (cp) mpas (cp) mpas (cp) Temperature max. 8 C 8 C 1 C 1 C Seal material no bearings nor seals in contact with the liquid shaft in stainless steel 1.4571/316 Ti with protective coating in PP Centrifugal impeller in PP or PVDF Ø 5 8 mm Ø 8 1 mm Ø 5 8 mm Ø 8 1 mm Pump housing Ø mm Ø 174 mm Ø mm Ø 174 mm Mounting flange in PP or PVDF outside Ø 5 mm outside Ø 5 mm outside Ø 45 mm outside Ø 45 mm Thread on outlet G 1 1 /4 A (BSP 1 1 /4 male) G 1 1 / A (BSP 1 1 / male) G 1 1 /4 A (BSP 1 1 /4 male) G 1 1 / A (BSP 1 1 / male) 3 mm 76 4 3 76 4 13 76 6 3 76 6 13 4 mm 76 4 4 76 4 14 76 6 4 76 6 14 5 mm 76 4 5 76 4 76 6 5 76 6 DRIVE MOTORS FOR CENTRIFUGAL IMMERSION PUMPS F 76 PP AND F 76 PVDF Three-phase motors protected to IP 55, with cable terminable box Capacity P Flange Ø Voltage Frequency Nominal speed,37 kw 1 mm 3/4 V 5 Hz 85 rpm 1 4,55 kw 1 mm 3/4 V 5 Hz 85 rpm 1 5,75 kw 1 mm 3/4 V 5 Hz 85 rpm 1 19 Drive motors explosion-proof to EEx e II T3 with cable terminal box on request. SCOPE OF SUPPLY A complete vertical centrifugal immersion pump consists of: drive motor, pump with mounting flange and the necessary accessories. Weight per pump 17 3 kg depending on the pump size, immersion length and motor kw. CENTRIFUGAL IMMERSION PUMP F 76 PP AND F 76 PVDF FLUX CENTRIFUGAL IMMERSION PUMPS F 76 PP AND F 76 PVDF IN POLYPROPYLENE OR POLYVINYLIDENFLUORIDE SIZE 185 AND 3 Typical applications Transferring and circulating of neutral or corrosive liquids in the whole field of the chemical industry and chemical engineering, electroplating industry, steel or stainless steel pickling plants, flue gas decontamination, exhaust air purification, water and waste-water treatment. Construction features Vertical centrifugal immersion pump for stationary application. The robust pump shaft is mounted in an upper pedestal and supported by two antifriction bearings. This construction, with the bearings spaced along the pedestal, ensures that any radial or axial forces are absorbed, even under heavy load. The result is a very smooth running pump. The solid version with support bars prevents the rotating elements from making contact with the pump housing and guarantees a very long service life, even in continuous use applications. As neither bearing nor seals are in contact with the liquid, the pump is very wear-resistant and suitable for dry running operation. The immersion length of the pump can be extended, up to mm maximum, by the suction tube option. A suction strainer welded onto the cover of the pump housing or onto the extension tube protects the pump against the ingress of coarse impurities. A range of carefully chosen impeller diameters, together with a range of three-phase motors in differing kw-ratings, ensures the optimum selection of pumps to meet the specific operating requirements. CONSTRUCTION FEATURES IN DETAIL antifriction bearings located in a pedestal seal kit prevents vapours entering the pedestal robust pump shaft with protective coating version with support bars for temperatures of up to 8 C (PP) or 1 C (PVDF) centrifugal impeller in differing diameters F 76 PP-185 F 76 PVDF-3 19
FLUX Performance chart F 76 PP-185 and F 76 PVDF-185 Dimensions F 76 PP-185 and F 76 PVDF-185 5 Ø 14 Ø 13 Ø 1 Ø 11 Three-phase motors: see page 1 5 Ø 1 Ø 1 Ø 13 Ø 1 Ø 11 Ø 14 5 1 5 3 35 4 3 1 1 3 max. 5 mm Variant 1 dimension p max. mm Variant Variant 3 and suction strainer Measured values ± 1% determined with water ( C). Nominal speed n = 85 rpm In order to achieve the desired output, centrifugal impellers in differing diameters are available. In determining the absorbed kw of the motor, multiply the absorbed kw shown in the above diagram with the specific gravity of the liquid to be pumped. Dimensions F 76 PP-3 and F 76 PVDF-3 Performance chart F 76 PP-3 and F 76 PVDF-3 35 Ø 16 Ø 3 5 Ø 14 Ø 13 Three-phase motors: see page Minimum or maximum liquid level when starting the pump. Also valid for the variants 1, and 3 max. 5 mm Variant 1 dimension p max. mm Ø 16 Ø 6 1 3 Variant 1 5 Ø 14 Ø13 4 Variant 3 and suction strainer 5 1 5 3 35 4 45 5.1.
Accessories: Extension tube in PP or PVDF in steps of 1 mm, Dimension p up to max. mm. Suction strainer in PP or PVDF welded onto the cover of the pump housing or onto the extension tube. FLUX CENTRIFUGAL IMMERSION PUMP F 76 PP IN POLYPROPYLENE AND F 76 PVDF IN POLYVINYLIDENFLUORIDE, VERSION WITH SUPPORT BARS, WITHOUT DRIVE MOTOR Type / Size F 76 PP-185 F 76 PP-3 F 76 PVDF-185 F 76 PVDF-3 Delivery rate Q max. 38 m 3 /h 45 m 3 /h 38 m 3 /h 45 m 3 /h Delivery head H max. 3 m water column 35 m water column 3 m water column 35 m water column Viscosity max. mpas (cp) mpas (cp) mpas (cp) mpas (cp) Temperature max. 8 C 8 C 1 C 1 C Seal material no bearings nor seals in contact with the liquid shaft in stainless steel 1.4571/316 Ti with protective coating in PP Centrifugal impeller in PP or PVDF Ø 1 14 mm Ø 13 16 mm Ø 1 14 mm Ø 13 16 mm Pump housing Ø 49 mm Ø 64 mm Ø 49 mm Ø 64 mm Mounting flange in PP or RCH 1 outside Ø 34 mm outside Ø 34 mm outside Ø 34 mm outside Ø 34 mm Thread on outlet G 1 /4 A (BSP 1 /4 male) G 1 /4 A (BSP 1 /4 male) G 1 /4 A (BSP 1 /4 male) G 1 /4 A (BSP 1 /4 male) 3 mm 76 4 3 76 4 33 76 6 3 76 6 33 4 mm 76 4 4 76 4 34 76 6 4 76 6 34 5 mm 76 4 5 76 4 35 76 6 5 76 6 35 DRIVE MOTOR FOR CENTRIFUGAL IMMERSION PUMP F 76 PP Three-phase motors protected to IP 55, with cable terminal box Capacity P Flange Ø Voltage Frequency Nominal speed 1,5 kw 16 mm 3/4 V 5 Hz 85 rpm 1 8, kw 16 mm 3/4 V 5 Hz 85 rpm 1 9 3, kw 16 mm 4 V 5 Hz 85 rpm 1 1 4, kw 16 mm 4 V 5 Hz 85 rpm 1 11 5,5 kw 16 mm 4 V 5 Hz 85 rpm 1 Three-phase motors explosion-proof to EEx e II T3 with cable terminal box on request. SCOPE OF SUPPLY A complete vertical centrifugal immersion pump consists of: drive motor, pump with mounting flange and the necessary accessories. Weight per pump 5 75 kg depending on the pump size, immersion length and motor kw. CENTRIFUGAL IMMERSION PUMP F 76 PP AND F 76 PVDF DIMENSIONS OF THREE-PHASE MOTORS PROTECTED TO IP 55 Capacity P Nominal speed X Ø Y Z,37 kw 85 rpm 1 143 183,55 kw 85 rpm 1 143 183,75 kw 85 rpm 3 8 1 1,1 kw 85 rpm 3 8 1 1,5 kw 85 rpm 44 176 7, kw 85 rpm 69 176 7 3, kw 85 rpm 33 196 5 4, kw 85 rpm 3 77 5,5 kw 85 rpm 45 46 313 3, kw 145 rpm 33 196 5 4, kw 145 rpm 3 77 5,5 kw 145 rpm 45 46 313 DIMENSIONS OF THREE-PHASE MOTORS EXPLOSION-PROOF TO EEX e II T3 Capacity P Nominal speed X Ø Y Z,75 kw 85 rpm 3 8 1 1,1 kw 85 rpm 3 8 1 1,5 kw 85 rpm 44 176 37, kw 85 rpm 69 176 37,5 kw 85 rpm 33 196 56 3,3 kw 85 rpm 3 79 1