Hot Pressing Device PQ-58

Similar documents
Welding kit. Use and maintenance manual. Use and maintenance manual PQ-01. Author: FT Page 1 of 4 Edition: 06/2017 R. 0 Replaces:

PM-1209/160W-B/458 Heat press with water cooling

User Guide. Lubricus Lubrication System LUB-D1/LUB-D2/LUB-D3/LUB-D4 (24 VDC)

Service Instructions. Syntron Light-Capacity Electromagnetic Model: F-T01-A DF-T01-A

6.0 SPECIFICATIONS CONTENTS. Calibration. According to factory procedureeeeeeeeeeeeeee Accuracy*

INSTALLATION INSTRUCTION & OWNER S MANUAL

X.. Series Helical and Bevel-Helical Gear Units

Installation and Operating Manual for Tank and Equipment Cleaning Nozzles Series 5TM

CO 3-WAY PNEUMATIC VALVE INSTRUCTION MANUAL 2080

CAUTION CONTENTS 5.0 WARRANTY

HV Gate Valve with pneumatic actuator

Operating Instructions. Globoidal cam gear

Mounting and operating instructions EB 5801 EN. Electric Actuators Type 5801 (Rotary Actuator) Type 5802 (Linear Actuator)

Operating Instructions Garlock Butterfly Valves DN : mm / 2-24

Operating and Maintenance Manual. for. HADEF overhead crane. as jointed crane TA

1.0 Introduction Mounting Procedure Verifying Calibration Accuracy Specifications Tension Ranges...

Air Actuated Hydraulic Bottle Jacks

Starting up hydraulic systems

Electropneumatic Converters i/p Converters Type 6111 Mounting and Operating Instructions EB 6111 EN

Operating Instructions K Always on the safe side.

original operating manual Operating manual Translation of the Item-No.: ,

INSTALLATION AND MAINTENANCE MANUAL FORM #PM-126 REV A 12/09

CM3-E Operation Manual DOK-347E / Rev.:1.01 KH / October 1999 Portable 3 turbine check meter

Operating instructions 1 4 Mode d emploi 5 8 Instrucciones de uso 9 13 Manual de instruções 15 18

ACROBAT SWING STAND MODEL

TABLE OF CONTENTS 10.0 LIMITED WARRANTY

PM-1359/160A-B/458 Heat press with air cooling

OTTO HYDRAULICS GmbH & Co KG SYSTEME UND KOMPONENTEN FÜR ÖLHYDRAULISCHE ANTRIEBE UND STEUERUNGEN SIEMENSSTRASSE 12/ FRIEDRICHSHAFEN

SIDE-WIND, A-FRAME TRAILER JACK. Model Due to continuing improvements, actual product may differ slightly from the product described herein.

BR 31a Rack-and-pinion Actuator,

Mounting and Operating Instructions EB 3913 EN. Electropneumatic Converters i/p Converter Type

OPERATING MANUAL LA-BO. Applicator

FMM-P-L. FluidMonitoring Module. Installation and Maintenance Instructions. English (translation of original instructions) Document No.

Assembly and Maintenance Manual Type ASNU

INSTALLATION, OPERATION & MAINTENANCE MANUAL

Swiveling gripper finger GFS 16-40

Data Sheet 11.2 Issue B

TABLE OF CONTENTS NOTES. 1.0 Operating principle... 02

Instruction Manual Extruder Sensor Rheomex 252/254

MV Series Motors Operation & Parts Manual

panelclaw.com Polar Bear III for 10 Degree

USER INSTRUCTIONS. Installation Operation Maintenance. NAF Setball SF Ball Sector Valves. Experience In Motion FCD NFENIM A4 09/16

3 Scotch-Weld. User s Manual. Polyurethane Reactive Adhesive Applicator. Use only with 3M Scotch-Weld Polyurethane Reactive Adhesives

Installation and Operation Instructions. VAG ROTOP Portable Electric Drive

TBP SERIES PUMPS OPERATION & PARTS MANUAL

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/17/14

User manual Pipe notcher Type: AL 1-2E

Operating Instructions. Parallel shaft cam gear

Operating Instructions & Parts Manual. Supa-Lite Lever Grease Gun. Model 48UJ77

c-go 24V/6A 24V/8A 24V/12A

Twin Power. Manual. Pneumatic Multiturn actuator in Standard and ATEX design WARNING! WARNING! Mounting. Assembly example

Catalyser Introduction. 3. Hazard Information. 2. Area of Application. 3.1 Symbology

VESTIL MANUFACTURING CORP. OPERATION & SERVICE MANUAL PORTABLE DRUM JACK (DRUM-55-S) 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703

TK08 TUNING KIT TECHNICAL MANUAL FOR 16/26/27/28 SERIES SHOCKS Revised 6/25/14 Tech Line: (952) Fax (952)

Air Actuated Axle Jacks

PrioVino Premier. Translation of Original Operating Instructions. Status: August First edition January 2018 / PrioVino GmbH

Data Sheet High Velocity Water Spray Nozzle. Issue B. Rapidrop Global. Ref: SPTDHV/E TECHNICAL DATA MAINTENANCE DESCRIPTION

UniTorq UTQ Quarter-Turn Actuator Installation and Operation Manual

Tension Meter. Edition FT 03.E. FT Series. Instruction Manual. Valid as of: Please keep the manual for future reference!

Application Tooling Specification Sheet

SHORT-STOP. Electronic Motor Brake Type G. Instructions and Setup Manual

TM SERIES MIXER TMS OPERATION & PARTS MANUAL

3M AEROSPACE & COMMERCIAL TRANSPORTATION DIVISION St. Paul, MN USA or or Made in USA

D58 Series Brake Instructions

PUSH BUTTON KEY CABINET

Usage Instructions of Solar Control for 3Way-Ball Valve

ACTUATOR LA44 PRODUCT DATA SHEET

Operating instructions K- Control 4960, 4965, Always on the safe side.

OPTIFLUX 2000 Quick Start

Laboratory Series. Ultraviolet Ozone Destruct System Installation, Operation and Maintenance Manual. One Source for All Your UV Needs!

Hydraulic Transmission Jacks

Installation and Operating Instruction for Complete Freewheels FRS, FRSG, and FRZ. E e Anderson Place Telephone

Service Instructions. Syntron Electromagnetic Feeder Model: F-010-B DF-010-B

1. Contents 1. CONTENTS INTRODUCTION SAFETY WARNINGS POWER TILT STANDARD OPERATING INSTRUCTIONS... 5.

Shower System. Dual Head INSTRUCTION GUIDE

Tissue Master. User Manual

Installation Instructions

CAUTION 7.0 WARRANTY CONTENTS. 1.0 Overview... 2

Model C230 Pump Controller

Translation of the Original operating instructions Lifting device Z 70 /...

Operating Manual for Drum Brake Type: EBN

SRSA limited warranty Policy and Procedure

Instruction Manual. Series R Peristaltic Pump. For file reference, please record the following data:

RENA AF371Feeder Operating Manual. Feeder. Operating Manual. Manual Part #: M AF371 Operations Rev

IP 900 W/KS & IP 900 D/KS

Adjustable Speaker Mount GRAVIS 8

Adjustable Speaker Mount GRAVIS 12

Operating manual. original operating manual. HDA eco Box 12/24V DC Automatic Dispenser. Translation of the. Item No.:

Operating Instructions

NOTICE- THIS K-MEMBER REQUIRES THE USE OF COIL OVER SUSPENSION. K-MEMBER WILL NOT WORK WITH FACTORY STYLE SPRINGS.

Control Gate Valve with stepper motor actuator

Contents INTRODUCTION... 2 CHECK YOU HAVE RECEIVED... 4 WHAT YOU WILL NEED...4 TECHNICAL CHARACTERISTICS...5 WIRING DIAGRAMES...6 CABLES...

Operating manual Separator

PMD DRIVER RELOCATION KIT For Chevy 6.5L Diesel Trucks

Application Tooling Specification Sheet

REC-54M OPERATION MANUAL. REC-54M: Gear-Driven Cable Cutter

8" - 12" Hydraulic Steel Squeeze Off Tool

c-go 12V/10A 12V/20A Power supply and battery charger Instruction manual

Assembly and Maintenance Manual Type AS

Micro Diaphragm Gas Sampling Pumps

Transcription:

Habasit AG Postfach, CH-4153 Reinach-Basel Phone ++41 61 715 15 15 Fax ++41 61 715 15 55 Operating Instructions 36007 Author: Gul/Ni/Nyk Page 1 of 20 Replaces: Edition 03/0102 Hot Pressing Device The is a hot pressing device for joining of Habasit machine- and spindle tapes up to a width of 50 mm and a thickness of 3.6 mm with the Quickmelt or Flexproof method. With an additional cooling tong and a guide rail in the width required for your application you have a joining system that enables you to exchange a tape in minutes. The width of the press plate is increased somewhat compared to the PQ-57. This enables you to make 35 mm long Flexproof joints also in situations where space is tight and visibility poor.

Page 2 of 20 Table of contents 1. General information... 3 1.1 Application... 3 1.2 Important safety terms... 3 1.3 Scope of supply... 4 1.3.1 Available accessories... 4 1.4 Ordering of accessories/spare parts... 5 1.5 Warranty... 5 1.6 Technical advice... 5 2. Mode of operation... 6 3. Initial start-up... 6 4. Hot-pressing of the belt/tape... 7 5. Service... 8 5.1 Maintenance... 8 5.2 Measuring of the plate temperature... 8 5.3 Adjusting of the thermostat... 9 5.4 Replacement of the power cord... 9 6. Illustrations... 10 7. Technical data... 11 8. Drawings... 12 8.1 Wiring diagram /8 (230 V)... 12 8.2 Wiring diagram /6 (120 V)... 13 8.3 Assembly of press... 14 9. Required accessories... 15 9.1 Guide rails, clamps... 15 9.2 Cooling tongs CD-60, CD-54... 16 9.3 Preparing devices... 16 9.3.1 Scissors for cutting to length AQ-40... 16 9.3.2 Flexproof cutter AF-102... 16 9.3.3 Flexproof die-cutting device AF-30... 17 Appendix: Checklist preventive maintenance Report sheet preventive maintenance Product Liability

Page 3 of 20 1. General information 1.1 Application The hot-pressing device was specifically designed for rapid and safe hot-pressing of Habasit machine tapes made of Hamid and spindle tape W-8 / W-16 with the Quickmelt and Flexproof systems. Tapes can be up to 50 mm / 2 in. wide and 3.6 mm / 0.14 in. thick. The hot-pressing device was developed solely for the purposes described in the operating instructions. Improper use, or use for other reasons than those described in the instructions, is not permissible. Habasit accepts no liability for the consequences of improper application. The hot-pressing device is manufactured according to recognized engineering principles and state-ofthe-art technology, and complies with applicable regulations. These operating instructions imply that all assembly, maintenance, and repair work, as well as operation of the press, be carried out by skilled personnel or monitored by responsible specialists. For reasons of scope, these instructions cannot cover all possible aspects of operation, maintenance, or repair. The indications given herein refer to the use of the machines according to their designated purpose by skilled personnel. In case of doubt or if further detailed information is required, please consult the manufacturer (Chapter 1.4) 1.2 Important safety terms In these operating instructions, you will find the terms WARNING, CAUTION, and INDICATION. They signal dangers or special information to be borne in mind. WARNING CAUTION INDICATION If disregarded, there is a danger of severe injury, and/or severe material damage. If disregarded, there is a danger of injury, and/or material damage may be caused. Technical information is emphasized if it is important and not readily apparent, even for skilled personnel. Please observe all indications for assembling, operating, and maintaining the machines, as well as all technical data! This will prevent possible trouble and/or damage to people or materials. Skilled personnel refer to persons authorized to perform the required work. These people have been sufficiently trained and introduced to their field of activity so that they are able to recognize and prevent dangers. They are aware of the pertinent provisions and safety regulations.

Page 4 of 20 1.3 Scope of supply Qty. Item 1 hot-pressing device packed in a carton box, with 1 Operating instructions 1.3.1 Available accessories Also refer to chapter 9. Guide rails of fixed width, inclusive of covering plate: 6 mm (672006) 3/8" (672113) 8 mm (672008) 10 mm (672010) 1/2" (672101) 11 mm (672011) 5/8" (672114) 12 mm (672012) 13 mm (672013) 14 mm (672014) 3/4" (672102) 15 mm (672015) 7/8" (672109) 16 mm (672016) 1" (672103) 18 mm (672018) 1 1/8" (672110) 20 mm (672020) 1 1/4" (672104) 22 mm (672022) 1 3/8" (672105) 25 mm (672025) 1 1/2" (672106) 30 mm (672030) 1 5/8" (672111) 35 mm (672035) 1 3/4 " (672107) 40 mm (672040) 1 7/8 " (672112) 50 mm (672050) 2" (672108) and 2 clamps for each guide rail Guide rail of adjustable width, from 25 to 50 mm, including 1 covering plate each for 25, 30, 40, 45 and 50 mm tape width and 2 metal clamps (672201), or from 1/2" to 2", including 1 covering plate each for the tape widths 1/2", 3/4", 1",1 1/4", 1 1/2", 1 3/4" and 2", and 2 metal clamps (672202). WARNING Use only Habasit guide rails. Particularly the use of metallic guide rails is not admissible, it may destroy the hot-pressing device. Scissors for cutting to length AQ-40 (690020) Scissors for cutting of Flexproof fingers AF-102 (690060) Punching device for Flexproof fingers AF-30 (690280) Cooling tongs CD-60 (690030) Temperature measuring device (N-28714 or N-28715) for checking the pressing temperature

Page 5 of 20 1.4 Ordering of accessories/spare parts Spare parts and accessories can be ordered directly from the manufacturer. Address: Habasit Italiana S.p.A. Via A. Meucci 8, Zona Industriale I-31029 Vittorio Veneto/TV Tel. ++39 438 91 13 Fax ++39 438 91 2374 Please accurately describe the parts required. State the numbers according to Section 8.3, Drawings Assembly of press and, if applicable, the required electric voltage for connection to the mains. WARNING The use of parts by other manufacturers not meeting Habasit specifications is not admissible. Habasit declines all responsibility for the consequences if non-habasit parts are used. 1.5 Warranty All tools undergo a strict final inspection. On the assumption of correct handling, they are warranted against material and manufacturing defects for 1 year. 1.6 Technical advice Our specialists will be pleased to advise you. For technical questions concerning function and condition of the hot-pressing device, please contact the manufacturer (see Chapter 1.4 for the address).

Page 6 of 20 2. Mode of operation The hot-pressing device functions according to the pressing-tongs principle: To open the heating plates pressed together by springs, apply substantial pressure to both handles. The hot-pressing device operates at a pressing temperature of 190 C / 374 F, preset at the factory. The temperature of the heating plates is regulated by an electronic circuit. Each heating plate comes with an exchangeable electric heat cartridge, the lower heating plate also with a temperature sensor, the upper heating plate with a thermofuse. The function of the hot-pressing device is indicated with a light indicator in the handle. 3. Initial start-up Check to make sure that the voltage indicated on the rating plate (5) conforms to the electrical connection voltage. Check to make sure that the metal heating plates (4) are clean. Check temperature of the heating plate. The temperature is preset at the factory at 190 C / 374 F. If a lower temperature is required, the temperature regulator can be adjusted accordingly (see 5.2, Measuring of the plate temperature). INDICATION Safe operation is assured if the marked handle (1) with the light indicator (2) is facing up (cable connection on the upper handle). For stationary operation, place hot-pressing device on a solid and heat-resistant support. WARNING Do not hang up hot-pressing device by the electrical connecting cable! During work breaks, while hot-pressing device is connected, put it on a flat surface with the marked side facing up.

Page 7 of 20 4. Hot-pressing of the belt/tape Procedure: For Hamid machine tapes manual 32103 and individual product datasheets. For spindle tape W-8, W-16 manuals 32110, 32111 and individual product datasheets. Plug in electrical connecting cable and preheat hot-pressing device. Preheating will take approx. 5 minutes. The light indicator (2) will change from a continuous light during heating up to intermittent light as soon as the adjusted temperature is reached. WARNING Do not touch the hot-pressing zone (3). Keep device away from water and meltable substances. Open hot-pressing device by squeezing the handles (6) and place guide rail with inserted, prepared belt/tape ends into the hot-pressing device, as described in the corresponding manual (also refer to chapter 9). Close hot-pressing device. After the prescribed pressing time, remove guide rail and let it cool under pressure in a suitable device chapter 9. WARNING After use, disconnect the hot-pressing device from the power supply and allow it to cool completely before storing it.

Page 8 of 20 5. Service 5.1 Maintenance Keep the hot-pressing device clean at all times. Clean the heating plates (4) regularly and remove all material residues. WARNING For cleaning with a cloth moistened with water or solvent, the press must be disconnected from the power supply. Do not reconnect to the power supply until the press is completely dry. Periodically inspect the power supply cable and connector plug for defects (insulation damage, etc.) and rectify or replace with the correct type where necessary. 5.2 Measuring of the plate temperature Check the operating temperature of the hot-pressing device once a month. Carry out this check in an interior room in a draft-free environment with an ambient temperature of between 18 C / 64 F and 25 C / 77 F Clamp sensor of temperature gauge between the heating plates (4) and heat for 5 minutes. Both plates are thus measured jointly. Heat up press for at least 5 minutes. The operating temperature has been reached when the electronic control switches the heating on and off in short intervals; the light indicator (2) will blink. The temperature gauge ought to indicate 190 C ± 3 C / 374 F ± 5,4 F If this is not the case, the temperature regulator has to be adjusted. See 5.3, Adjusting of the thermostat.

Page 9 of 20 5.3 Adjusting of the thermostat The maximum plate temperature of 190 C / 374 F, preset at the factory, must not be exceeded by more than ± 3 C / ± 5.4 F from 190 C / 374 F. It can therefore only be adjusted with a precision temperature measuring device (see 1.3.1, Available accessories). WARNING All work on the hot-pressing device involving electrical parts has to be carried out by the respective specialists only. Observe your local laws about required training of such personnel. If the measured temperature deviates above the maximum value of 193 C / 379.4 F or below 187 C / 368.6 F, the heating control is to be adjusted as follows: Remove cover screw (8) from adjustment potentiometer (7) Move adjustment potentiometer of the heating control (7), using an insulated screwdriver, turning it ever so slightly: clockwise: temperature will rise, counterclockwise: temperature will drop. After 5 minutes measure plate temperature to check as described above. Proceed carefully and adjust gradually. Observe temperature change. Re-cover adjustment potentiometer (7) with cover screw (8) CAUTION Make sure not to let the temperature rise above 195 C / 383 F during adjustment. Excessive temperatures may damage the hot-pressing device or blow the thermofuse. 5.4 Replacement of the power cord Check power cord periodically. In case of damage replace with the same type (H05-RNF). To make sure only skilled staff will do this repair, special tools are required for this operation. WARNING All work on the hot-pressing device involving electrical parts has to be carried out by the respective specialists only. Observe your local laws about required training of such personnel.

Page 10 of 20 6. Illustrations 1 2 3 6 Illustration 1 5 4 8 7 Legend illustration 1 and 2 1 2 3 4 5 6 7 8 Top side of the hot-pressing device Light indicator Hot-pressing zone Pivoting metal heating plates Rating plate Heat insulated handles Adjustment potentiometer of the heating controller Cover screw of adjustment potentiometer Illustration 2

Page 11 of 20 7. Technical data Belt / tape width max. [mm] [in] 50 2.0 Belt / tape thickness max. [mm] [in] 3.6 0.14 Finger length for Flexproof, max. [mm] [in] 35 1.4 Min. endless belt/tape length [mm] [in.] 250 10 Max. deviation of plate temperature [ C] [ F] ± 3 ± 5.4 Heating up time to 190 C / 374 F [min.] 5 Power consumption [W] 2 x 225 Voltage [V~] 230 (/8) or 120 (/6) Dimensions (L x W x H) [mm] [in] 280 x 70x 120 11 x 2.8 x 4.7 Net weight [kg] [lbs] 0.83 1.85

Page 12 of 20 8. Drawings 8.1 Wiring diagram /8 (230 V)

Page 13 of 20 8.2 Wiring diagram /6 (120 V)

Page 14 of 20 8.3 Assembly of press

Page 15 of 20 9. Required accessories 9.1 Guide rails, clamps These accessories are necessary for producing perfect fusion joints. The width and numbers of guide rails to be used will depend on the width of the tape used and the requirements of the machine/installation. Once the tape ends have been inserted into the corresponding guide rail of fixed width ill. (3), or adjustable width ill. (4) and fixed in place with the covering plate, the two clamps are applied at an angle so as to prevent the tape from shifting during the hot-pressing process. Place the guide rail in the precise center of the open hot-pressing device and close ill. (5). This assures uniform distribution of the heat to guide rail and joining area. Illustration 3 Illustration 4 Illustration 5

Page 16 of 20 9.2 Cooling tongs CD-60, CD-54 The cooling tongs CD-60 and CD-54 are designed for the rapid cooling of the joint, still within the guide rail ill. (6). After the specified pressing time has elapsed, the cooling tongs must be clamped onto the guide rail as quickly as possible. If the cooling tongs are used repeatedly at short intervals, they get warm. They may be cooled by dipping them in cold water. Illustration 6 9.3 Preparing devices 9.3.1 Scissors for cutting to length AQ-40 The scissors for cutting to length AQ-40 permit clean cutting of the tapes at a 60 angle. Tapes up to 40 mm / 1.57 in. wide and 3 mm / 0.12 in. thick can be cut to length with these scissors ill. (7). 9.3.2 Flexproof cutter AF-102 The Flexproof-Cutter AF-102 is a device for preparing (finger cutting) Habasit machine tapes up to a width of 100 mm/4 in. and a thickness of 2 mm/0.08 in. for Flexproof (finger) joints. It is suitable for the standard Habasit 8 x 30 mm finger geometry. The tape is positioned and securely clamped on an aluminum support. Fingers are then cut manually. The cutter is precisely positioned on the support with a pin matching a row of precisely cut indexing grooves; the angle is given by a guiding block fixed to the cutter. ill. (8). Illustration 7 Illustration 8

Page 17 of 20 9.3.3 Flexproof die-cutting device AF-30 The AF-30 is a device for preparing (die-cutting) of Habasit belts and tapes up to width of 30 mm / 1.2 in. and a thickness of 3 mm / 0.12 in. for Flexproof (finger) joints. It is suitable for the standard Habasit finger geometries with a pitch of 6 or 8 x 30 mm (different cutting heads). Die-cutting is done in just two manual strokes resulting in the most precise finger cut and therefore optimum joint strength. The AF-30 lends itself especially well to low to high volume production of spindle and machine tapes off pre cut coils. ill. (9). Illustration 9

Appendix Checklist preventive maintenance Page 18 of 20 Responsible persons: A: Machine Operator B: Maintenance Technician Work to be carried out Performance Spares number (see operating instructions No. 36007 for further information and reference numbers) periodically (monthly) Evaluation criterion Daily 1 6 Remarks 1. Cleaning 1.1 Clean the press after use, remove residual deposits A 2. Inspect the connector cable 2.1 Examine the cable and connector plug for defects B damaged insulation, defective couplings 3. Measurement of the heater plate temperature 3.1 Proceed as detailed in operating instructions 36007, Section 5.2 B Remarks and notes:

Appendix Report sheet preventative maintenance Page 19 of 20 Machine type: Machine no.: Actions to be performed see checklist Next (daily work not recorded) Check 2.1 Inspect the cable for damage Date of first placing in operation: Performed Next Performed Next Performed Next Performed Initials Date Check Initials Date Check Initials Date Check Initials Date 3.1 Measure the heater plate temperature Observations, repairs:

Appendix Page 20 of 20 Product liability, application considerations If the proper selection and application of Habasit products are not recommended by an authorized Habasit sales specialist, the selection and application of Habasit products, including the related area of product safety, are the responsibility of the customer. All indications / information are recommendations and believed to be reliable, but no representations, guarantees, or warranties of any kind are made as to their accuracy or suitability for particular applications. The data provided herein are based on laboratory work with small-scale test equipment, running at standard conditions, and do not necessarily match product performance in industrial use. New knowledge and experiences can lead to modifications and changes within a short time without prior notice. BECAUSE CONDITIONS OF USE ARE OUTSIDE OF HABASIT S AND ITS AFFILIATED COMPANIES CONTROL, WE CANNOT ASSUME ANY LIABILITY CONCERNING THE SUITABILITY AND PROCESS ABILITY OF THE PRODUCTS MENTIONED HEREIN. THIS ALSO APPLIES TO PROCESS RESULTS / OUTPUT / MANUFACTURING GOODS AS WELL AS TO POSSIBLE DEFECTS, DAMAGES, CONSEQUENTIAL DAMAGES, AND FURTHER-REACHING CONSEQUENCES.