Reed es/direct Mounting Type D-Z73/Z76/Z80 uto Internal Circuits Lead wire colors inside [ ] are old colors prior to conformity with IEC standards. D-Z73 Reed LED Resistor Zener diode Contact box (+) () uto Specifications With Indicator Light uto part no. pplicable load voltage Maximum load current or current range Contact Internal voltage drop Without Indicator Light uto part no. pplicable load voltage Maximum load current Contact Internal resistance 24VDC to 40m uto Weight Table D-Z73 D-Z76 D-Z80 D-Z73 D-Z76 Relay, PLC IC 100VC 4 to 8VDC to 20m 20m None 2.4V or less 0.8V or less Red LED lights up when ON C 24V DC or less 0m D-Z80 Relay, PLC, IC C 48V DC 40m None 100V 20m 1Ω or less (including lead wire length of 3m) Leakage current.. None Operating time... 1.2ms Lead wires... Heavy duty oil resistant vinyl cord,, 0.2mm², (, [Red, ]) 3 wire (,, [Red, White, ]), 0.m Impact resistance 300m/S² {30.6G} Insulation resistance.. 0MΩ or more at 00VDC (between lead wire & case) Withstand voltage 00VC for 1min. (between lead wire & case) mbient temperature. 10 to 60 C Enclosure... IEC2 standard IP67, watertight (JISC020) For a lead wire length of 3m, "L" is shown at the end of the part number. Example) D-Z73L Lead wire length 0.m 10 C DC Unit: g Lead wire length 3m 4 4 D-Z76 Reed LED D-Z80 Reed Resistor Reverse current prevention diode DC (-) Contact box (+) DC power supply () (±) ( ) ± uto Dimensions Slotted head set screw (M x 4l) 27.6 Type D-Z80 without indicator light 1. Note) 1. The load is an induction load 2. The lead wire length to the load is m or more 3. The load voltage is 100VC Use a contact box in any of the above situations, as the life of the contacts may otherwise be reduced. Refer to page 23 for detailed specifications of the contact boxes..7 l Operating range (see page 23) 1 Most sensitive position 20
Solid State es/direct Mounting Type D-Y, D-Y6, D-Y7P (V) uto Specifications D-Y, D-Y6, D-Y7P, D-Y7PV (With Indicator Light) uto part no. D-Y D-Y6 D-Y7P D-Y7PV D-Y D-Y6 Wiring 3 wire Output NPN type PNP type pplicable load Power supply voltage Current consumption IC, Relay, PLC, 12, 24VDC (4. to 28VDC) 10m 24VDC Relay, PLC voltage current 28VDC or less 40m or less 80m or less 24VDC (10 to 28VDC) to 40m or less Internal voltage drop 1.V or less (0.8V or less at load current of 10m) 0.8V or less 4V or less Leakage current 100µ or less at 24VDC 0.8m or less at 24VDC Red LED lights up when ON Operating time... 1ms or less Lead wires...heavy duty oil resistant flexible vinyl cord,, 0.mm², 3 wire (,, [Red, White, ]), (, [Red, ]) 0.m For a lead wire length of 3m, "L" is shown at the end of the part number. (Example) D-YL Impact resistance... 1,000m/s² (102G) Insulation resistance... 0MΩ or more at 00VDC (between lead wire & case) Withstand voltage... 1000VC for 1min. (between lead wire & case) mbient temperature... 10 to 60 C Enclosure... IEC2 standard IP67, watertight (JISC020) uto Internal Circuits Lead wire colors inside [ ] are old colors prior to conformity with IEC standards. D-Y, Y6 Weight Table D-Y, Y6, Y7P 0.m 10 Lead wire length 3m 3 Unit: g D-Y, Y6, Y7PV Dimensions 0 D-Y, Y D-Y7P 27.6 1. DC () Slotted head set screw (M x 4l) D-Y7P (V) 1 Most sensitive position DC () D-Y6, Y6 D-Y7PV 27.3 D-Y, Y6 (+) Slotted head set screw (M x 4l) 7 (-) 1 Most sensitive position 21
2 Color Indication Type Solid State es D-Y7NW/Y7PW, D-Y7W uto Internal Circuits Lead wire colors inside [ ] are old colors prior to conformity with IEC standards. D-Y7NW(V), 3 wire NPN output D-Y7PW(V), 3 wire PNP output D-Y7W(V), DC () DC () uto Specifications D-Y7 W, D-Y7 WV (With Indicator Light) uto part nos. D-Y7NW D-Y7NWV D-Y7PW D-Y7PWV D-Y7W D-Y7WV Wiring 3 wire Output NPN type PNP type pplicable load Power supply voltage Current consumption IC, Relay, PLC, 12, 24VDC (4. to 28VDC) 10m or less 24VDC Relay, PLC voltage current Internal voltage drop 28VDC or less 40m or less 1.V or less (0.8V or less at load current of 10m) 80m or less 0.8V or less 24VDC (10 to 28VDC) to 40m 4V or less Leakage current 100µ or less at 24VDC 0.8m or less at 24VDC uto Weight Table D-Y7N, Y7P D-Y7 uto Dimensions D-Y7 W Operating position... Red LED lights up Optimum operating position Green LED lights up Operating time...1ms or less Lead wires... Heavy duty oil resistant flexible vinyl cord,, 0.mm², 3 wire (,, [Red, White, ]), (, [Red, ]) 0.m For a lead wire length of 3m, "L" is shown at the end of the part number. (Example) D-Y7NWL Impact resistance... 1,000m/s² (102G) Insulation resistance. 0MΩ or more at 00VDC (between lead wire & case) Withstand voltage. 1000VC for 1min. (between lead wire & case) mbient temperature 10 to 60 C Enclosure... IEC2 standard IP67, watertight (JISC020) 0.m 11 33. Lead wire length Slotted head set screw (M x 4l) 1. 3m 4 0 Unit: g (+) 1 Most sensitive position () D-Y7 WV 33 s/display method Operating range ON OFF SMC Slotted head set screw (M x 4l) Indicator Red Green Red Optimum operating position 1 7 Most sensitive position 22
SWITCH Series MF uto Mounting Positions Contact Protection oxes/, D-Z7, D-Z80 (pplicable models) D-Z73, Z80 The above auto es do not have built-in contact s. 1. The load is an induction load. 2. The lead wire length to the load is m or more. 3. The load voltage is 100V or 200VC. Use a contact box in any of the above situations, as the life of the contacts may otherwise be reduced (they stay ON continuously). (mm) Mounting position Operating range Note) MF 103. 134. 8 MF 32 124. 14. Contact Protection ox Specifications Part No. voltage Max. load current 100VC or less 2m 200VC 1m 24VDC 0m D-Y, D-Y6, D-Y7P(V) Lead wire length connection side 0.m connection side 0.m Mounting position Operating range Note) uto Mounting MF 103. 134. (mm) MF 32 124. 14. Note) The operating range is a standard including hysteresis, but is not guaranteed (variation ±30%). There may be large changes depending on the ambient environment. 3 Contact Protection ox Internal Circuits Lead wire colors inside [ ] are old colors prior to conformity with IEC standards. Surge absorber Zener diodes Choke coil Choke coil (+) () Contact Protection ox/dimensions 4.4 3.4 CD-P VOLT 18 uto 38 46. Flat head watchmakers screw driver Contact Protection ox/connection Caution (M x 4l) (ccessory) When tightening the auto mounting screw, use a flat head watchmakers screw driver with a handle about to 6mm in diameter. Tighten the screw to a torque of about 0.0 to 0.1N m. s a rule, it can be turned approximately 0 past the position at which tightening can be felt. To connect a unit and contact box, connect the lead wire on the side of the contact box marked SWITCH to the lead wire coming out of the unit. In addition, place the unit and contact box as close together as possible, with a lead wire length of no more than 1 meter. 23
asic Wiring Series MF uto Connections and Examples Solid state 3 wire, NPN (Power supplies for and load are separate.) Solid state 3 wire, PNP Examples of Connection to PLC <Solid state> <Reed > Indicator light,, etc. Indicator light,, etc. Specification for sink input Specification for source input 3 wire, NPN 3 wire, PNP Connect according to the applicable PLC input specifications, as the connection method will vary depending on the PLC input specifications. PLC internal PLC internal PLC internal Connection Examples for ND (Series) and OR (Parallel) 3 wire ND connection for NPN output (Using relays) Relay Relay Relay contact PLC internal with 2 ND connection with 2 OR connection ND connection for NPN output (Performed with es only) The indicator lights will light up when both es are turned ON. OR connection for NPN output = 24V 4V x 2 pcs. = 16V Example: Power supply is 24VDC Voltage decline in is 4V When two es are connected in series, a load may malfunction because the load voltage will decline when in the ON state. The indicator lights will light up if both of the es are in the ON state. Residual voltage voltage at ON = Power supply voltage x 2 pcs. = 1m x 2 pcs. x 3kΩ = 6V Example: impedance is 3kΩ Leakage current from is 1m <Solid state> When two es are connected in parallel, malfunction may occur because the load voltage will increase when in the OFF state. leakage load voltage at OFF = current x 2 pcs. x impedance <Reed > ecause there is no current leakage, the load voltage will not increase when turned OFF, but due to the number of es in the ON state, the indicator lights will sometimes get dark or not light up, because of dispersion and reduction of the current flowing to the es. 24
Series MF Selection Types of Units and Parts Type of units and parts Type of units Catalog pages Single units P.1 to P. Combination Units P.11 to P.18 2 types are available, curved type and straight type. Mounting and piping methods are the same as for existing products. 2 types of construction are available. 2 dimensional structures are created by combining curved and straight type units, and long strokes are created by combining straight type units only. Content Connecting section Configuration End units End unit MF ore size MFT ore size Single units Combination units 37
Selection Series MF Type of parts Set parts P.11 to P.14 Parts P.16 Spare parts P. 4, Optional parts P. 2 Connecting parts Note 1) Parts for combination units. These consist of combinations of cylinder tube and body parts, and "combination units" are made by linking these set parts. Curved units, straight units, maintenance units and end units, etc. are available. Set parts can also be used as service parts (for unit replacement of cylinder tubes and bodies). Service parts. These are service parts for each of the cylinder tubes and bodies included in the set parts. Spare parts Service parts (seal list) consisting of various seals and wear rings, etc. Optional parts Support brackets for Support brackets attaching cylinders & side supports are available as optional parts. Connecting parts Required for connection of the set parts. Tube ody Wear ring Piston seal Tube ody End unit Oil felt seal Support bracket MFT ore size Connecting units (set parts) MFP T G Cylinder tube ody ore size Parts Spare parts MF ore size PS single unit Spare parts Optional parts MF-S32 (side support) MY-S (support bracket) Connecting parts MFT 32-CP Connecting parts Note 1) Since the connecting parts (MFT 32 CP) are required for connection of the set parts, order in accordance with the number of connecting sections (unit joints). Note 2) Connecting parts are also available for the cylinder tube section and body section parts only. MFPT 32 CP (For cylinder tube) Cylinder tube Connecting parts MFPG 32 CP (For body) ody Connecting parts 38