22 LP-LINEARHO DC MODULE, 800mA MAX CURRENT Low Profile design, no magnets Direct mount to luminaire housing Superior thermal performance than standard LinearHO Higher aluminum material density Extruded Aluminum material for thermal management High lumen, high efficacy General Specifications Nominal Operating Voltage @ Max Current Max Input Current 5.6VDC (with basic insulation design) 800mA Nominal DC Power Consumption @ Max Current Initial Lumens Output @ Max Current 28.50W 4,899 lumens @ 4000K / 80 CRI / 25 C Beam Angle 120 CRI Storage Temperature Range 80CRI (standard), 90CRI available -40 C to 100 C / -40 F to 212 F Operating Temperature Range (Ta) -40 C to 55 C / -40 F to 11 F Maximum Case Temperature (Tc) 2 Estimated Lumen Maintenance Color Consistency Overall Size PCB Material / Thermal Conductivity Extruded Material / Finish LED Quantity Module Weight PCB Part Number Maximum Screw Installation Torque Connector Type Packaging: Master Carton Thermal Feedback Safety/Compliance Energy Efficiency Label (EEI-Label) Warranty 1 Accessories: Diffused lens compatible For use in UL Class 2 lighting systems Suitable for DLC applications: L70 >60,000hrs/L90 40,000hrs Meets UL8750 recognized compliant The module is supplied by short circuit proof SELV controlgear L70: Tc max 105 C (Ts=110 C) / L90: Tc max 105 C (Ts=110 C) L70: >60,000Hrs / L90: 40,000Hrs Binning per ANSI C78.77-2015 @ 25 C; SDCM 22 L x 1.26 W x 0.29 H (559mm x 2mm x 7.4mm) MCPCB (Aluminum Clad)/ 1.5W / mk Aluminum/surface treatment with Anodic Oxidation 60pcs. 141g / 0.1lb PTL022C01M1 25 inch - ounces WAGO #2060-452 / 998-404 (2 pin connector) 40pcs. Not Available curus (File # E51548) Suitable for UL Class 2 Lighting Systems Compliant Dry and Damp Location CE (IEC 6201: 2008. AMD1: 2012, AMD2: 2014) SELV A++ 5 years @ Max. Tc from the date of manufacture 1 2 Measured electrical data per UL file TM-21 Reported Numbers Page 1 of 9
Part Number Matrix V M U 080 00 LP8 XX A Product Line V = Vizion Type M = Module (UL Class 2) Control Type U = None Electrical and Optical Specifications LP-LinearHO Module Part Number Number of LED VMU08000LP8xxA 60 Luminous Flux De-Rating: CCT and CRI Multipliers CRI 80(R9> 0) CRI 90(R9>50) Input Current Input Current 080 = 800mA Max. Power 00 = 0W Design LP=Low Profile 2700K 000K 500K 4000K 5000K 0.92 0.95 0.97 1.00 1.01 0.77 0.84 0.8 0.85 0.86 NOTES: 1) Performance based on Tc mod = 25 C. See thermal de-rating chart (pg. ) for higher temperature operation 2) Standard lumen output and efficacy is calculated for standard options. Reference CCT & CRI vs Luminous Flux chart for lumen ratio calculation. ) Specifications are subject to change without notice. 4) The LED DC Module can be configure with different LED chip quantities, series and parallel design configurations to meet a specific design requirement. Contact Fulham for further assistance. 5) * Indicates maximum rated current. Modules may be operated at a current less than or equal to this value, below the Tc rating. 6) 70CRI is NOT available. Standard Product offering (All other options are made to order with MOQ and lead time) 4 See page #7 for Conformal Coating information. Made to order (MTO). CRI 8 = 80 9 = 90 Color Temperature 27 = 2700K 0 = 000K 5 = 500K 40 = 4000K 50 = 5000K 57 = 5700K 65 = 6500K 75mA 2.0V 2.4W 5V W 526 lm 219 lm/w 100mA 2.0V.2W 5V 4W 700 lm 219 lm/w 125mA 2.0V 4.0W 5V 4W 87 lm 218 lm/w 150mA 2.7V 4.9W 6V 5W 1045 lm 21 lm/w 175mA 2.6V 5.7W 6V 6W 1216 lm 21 lm/w 200mA.0V 6.6W 6V 7W 187 lm 210 lm/w 225mA 2.9V 7.4W 6V 8W 1555 lm 210 lm/w 50mA.7V 11.8W 7V 1W 280 lm 202 lm/w 75mA.9V 12.7W 7V 14W 2541 lm 200 lm/w 400mA 425mA 4.0V 4.1V 1.6W 14.5W 7V 8V 15W 16W 2699 lm 2856 lm 198 lm/w 197 lm/w 450mA 4.2V 15.4W 8V 17W 010 lm 195 lm/w 500mA Nom. Forward Voltage (VDC) 4.4V Nom. Rated Power 17.2W Max. Fwd. Voltage 8V Max. Rated Power 19W Nom. Lum. Flux @4000K/80 CRI 12 lm 5700K 1.01 0.86 Nom. Efficacy @4000K/80 CRI 250mA.2V 8.W 7V 9W 1724 lm 208 lm/w 275mA.1V 9.1W 6V 10W 1890 lm 208 lm/w 00mA.V 10.0W 7V 11W 2055 lm 206 lm/w 25mA.5V 10.9W 7V 12W 2219 lm 204 lm/w 475mA 4.V 16.W 8V 18W 162 lm 194 lm/w 19 lm/w 525mA 4.5V 18.1W 8V 20W 460 lm 191 lm/w 550mA 4.5V 19.0W 8V 21W 605 lm 190 lm/w 575mA 4.6V 19.9W 8V 22W 748 lm 188 lm/w 600mA 4.8V 20.9W 8V 2W 888 lm 186 lm/w 625mA 4.9V 21.8W 8V 24W 4025 lm 185 lm/w 650mA 4.9V 22.7W 8V 25W 4159 lm 18 lm/w 675mA 5.1V 2.7W 9V 26W 4291 lm 181 lm/w 700mA 5.1V 24.6W 9V 27W 4418 lm 180 lm/w 725mA 5.V 25.6W 9V 28W 4544 lm 177 lm/w 750mA 5.V 26.5W 9V 29W 4666 lm 176 lm/w 775mA 5.5V 27.5W 9V 0W 478 lm 174 lm/w 800mA* 5.6V 28.5W 9V 1W 4899 lm 172 lm/w 4 Option A = Standard D = Conformal Coating (MTO) 6500K 1.00 0.85 Page 2 of 9
Thermal Specifications Storage Temperature Range Operating Ambient Temperature Range (Ta) Maximum Case Temperature LP-LinearHO DC Module -40 to +100 C / -40 to +212 F -40 to 55 C / -40 to 11 F L70 = 105 C (221 F) / L90 = 105 C (221 F) Thermal De-Rating: Tc vs. Luminous Flux vs. Forward Voltage Module Case Temperature (Tc) 25ºC 0ºC 5ºC 40ºC 45ºC 50ºC 55ºC 60ºC 65ºC 70ºC 75ºC 80ºC 85ºC 90ºC 95ºC 100ºC Total Vf Multiplier 1.000 1.000 0.997 0.99 0.99 0.990 0.987 0.987 0.984 0.984 0.980 0.977 0.977 0.974 0.970 0.967 Luminous Flux Multiplier 1.000 0.991 0.982 0.97 0.964 0.95 0.944 0.95 0.926 0.917 0.908 0.899 0.889 0.880 0.862 0.85 Page of 9
Certification Chart Energy Star TM-21 Calculator Data Classification Model Energy Efficiency Label (EEI-Label) Suitable for UL Class 2 Lighting System VMU08000LP8xxA YES YES YES A++ YES Tc Module Reported L70 Reported L90 55 C >60,000 Hrs >54,000 Hrs 85 C >60,000 Hrs 46,000 Hrs 105 C >60,000 Hrs 40,000 Hrs Tc Module Calculated L70 Calculated L90 55 C 180,000 Hrs 54,000 Hrs 85 C 154,000 Hrs 46,000 Hrs 105 C 1,000 Hrs 40,000 Hrs Product Image: LP-LinearHO Module TOP VIEW Page 4 of 9
Mechanical Drawings (Scale 1:5) 22 [559mm] Overall Dimensions Length Width Height 22 [559mm] 1.26 [2mm] 0.29 [7.4mm] 4. [110mm] 4. [110mm] 2.40 [61mm] 0.79 [19.96mm 1.26 [2mm] 1.14 [29mm] 22.01 [559mm] ø0.17 x 12 [ø4.2mm] x 12 TOP VIEW BOTTOM VIEW 0.29 [7.4mm] 0.14 [.55mm] SIDE VIEW Page 5 of 9
Accessories 22 Diffuser Lens Harness Fulham Part Number: 22 : TLE-OPT-120-004 Interconnects White polycarbonate diffuser lens - 82% transmissivity at nominally rated currents. ISOMETRIC VIEW Interconnect Type: WAGO Double pins to interconnect Modules (#2060-952/028-000) NOTES: TLC-HN02 (1 and 2 module connection) 0. 8. mm 0.7 18.6 mm 22 560 mm ISOMETRIC VIEW TLE-OPT-120-004 (Diffused Lens) 0.74 18.7 mm PRELIMINARY Approvals: curus, UL 1977, and Compliant LENS MODULE 1.27" [2.24m] TLC-HN04 ( and 4 module connection) 0. 8. mm 0.7 18.6 mm 1) Interconnects are NOT sold by Fulham. 2) Do not connect LinearHO Modules in parallel (end to end) if the current exceeds the maximum module rated current. This type of wiring would cause the pass-through current on the first module to exceed the rated current. This setup is in reference to wiring diagram #2 per Fulham's wiring diagram (see link on page #8). If the current is higher than the rated max, it is recommended to use wiring diagram # 22 560 mm 1.18 29.9 mm ISOMETRIC VIEW SIDE VIEW Installation Steps when using clamps: 1. Place the LED Module on the luminaire surface. 2. Place the Diffuser lens on top of LED module (line it up with LED module mounting edges).. Push down to snap into place. 0.6" [16mm] Top View Page 6 of 9
Guidelines Termination Notes Connector Type: WAGO #2060-452 / 998-404 (2 pin push wire connector) AWG: 24...18 solid wire Strip length: 7...9mm / 0.28...0.5in Connector Max amp. rating: 9 Amps. For more detail information, please visit Wago s website: http://www.wago.com/infomaterial/pdf/51001.pdf Connector Fastening Notes If fastening by screw hole a recommended screw size: 6-20 x 5/8" flat head drilling screws. Use all available screw holes to ensure good contact between back side of module and mounting surface. Refer to max specified torque for installation. If fastening using double-sided tape, start with clean, oil-free and dust-free surface. Peel backing and place LED module on mounting surface. Firmly press down on the module to ensure good adherence. Follow the double-side tape manufacturer s installation instructions. BJB P2F (Push-to-Fix) fixing elements for PCBs can be used to fasten LED modules to mounting surface. Reference BJB's website for ordering information and specific model to use: http://www.bjb.com/index.php?pid=76706&lid=10. HEYCO HEYClip Snap Rivets 905 is recommended for fast and easy installation with clean and finish look. Heyco Rivet 905 For more detail information, please visit Heyco website: https://www.heyco.com/nylon_pvc_hardware/product.cfm?product=snap-rivets Environmental Rating / Conformal Coating The DC LP-LinearHO Modules have been evaluated for use in dry or damp locations only. If used in wet locations, acceptability and the need for additional evaluation shall be determined in the end product. Electrostatic Sensitive Product (ESD) Fulham's LP-LinearHO modules are available with conformal coating; made to order with MOQ and lead time will apply. The conformal coating is a silicone based material which is double sprayed on the module only (LEDs and PCB). Conformal coating is recommended for the following applications: near ocean where salt is present, constant moisture, refrigeration, continuously high humidity, or outdoor applications. An IP rating of IP64 or IP65 is achieved when the conformal coating is used, but other factors should be considered. Fulham still recommends the luminaire also meet an IP64/65 rating. Fulham LED products should be handled with proper measures to protect against any potential ESD damage. When servicing, personnel should be ground and direct contact with LED should be avoided. Thermal Management Proper thermal management should be employed to ensure life and reliability of product. Max Tc of module should not be exceeded. Use of thermal grease, paste, pad, or other material interface is highly recommended. Polarity Notes DC LP-Modules are polarity sensitive. Ensure that positive from LED Driver is connected to positive of LED modules and that negative from LED Driver is connected to negative of LED modules. Polarities of modules are marked with + for positive and - for negative. Page 7 of 9
Color and Binning Optical Spectrum 0.44 0.4 0.42 0.41 CIE, y 0.40 0.9 0.8 0.7 0.6 0.5 0.4 5000K 4000K 500K 000K 2700K 2700K 000K 500K 4000K 5000K 0. 0.2 0.1 0. 0. 0.1 0.2 0. 0.4 0.5 0.6 0.7 0.8 0.9 0.40 0.41 0.42 0.4 0.44 0.45 0.46 0.47 0.48 0.49 7 SCDM Rectangle SCDM Ellipse CIE, x 400 450 500 550 600 650 700 750 800 Wavelength (nm) Compatible Fulham Drivers (Please use the links below for a complete list of compatible Fulham drivers and wiring diagrams) LP-LinearHO System Combination: Fulham s Wiring Diagrams: https://cdn.fulham.com/pdfs/specsheets/dc-modules-wiring-diagrams.pdf Compatible with Fulham Hotspot EM Systems. NOTES: 1) The Color and Binning and Optical Spectrum charts are for reference only. For more detailed info, contact factory. 2) Reference Samsung Chromaticity Diagram for Color and Binning. Binning per ANSI C78.77-2015 @ 25 C; SDCM. ) The Optical Spectrum values vary depending on product type and color rank. 4) Driver not included. 5) Do not connect LinearHO Modules in parallel (end to end) if the current exceeds the maximum module rated current. This type of wiring would cause the pass-through current on the first module to exceed the rated current. This setup is in reference to wiring diagram #2 per Fulham's wiring diagram (see the link above). If the current is higher than the rated max, it is recommended to use wiring diagram #. Page 8 of 9
D/C : XXXXXXXXXX C/N : XX/100 N.W : 5.62 Kgs. G.W : 6.9 Kgs. BOX SIZE : 595 x 270 x 1 10 MM 1 0 8 4 7 0 9 8 0 4 6 2 8 QUANTITY: B.N: XXXXXXXXX MADE IN CHINA VMU08000LP8xxA Packaging Master Carton L H VMU08000LP8xxA 40 W OUTER DIMENSION L W H 2.4 (595mm) Net Weight 12.4 lbs. (5.62kg) 10.6 (270mm) Gross Weight 14.09 lbs. (6.9kg) 4. (110mm) QUANTITY 40pc. Page 9 of 9