SKID STEER LOADER ATTACHMENT DIRECTORY SK714-5 SK815-5 SK818-5 SK820-5 SK1020-5 SK1026-5
INTRODUCTION This directory provides Komatsu Skid Steer Loader distributors and customers with a listing of single source, worksite application, attachments. These attachments are designed and manufactured by some of the leading attachment manufacturers for specific fit to our Skid Steer Loaders. And since these attachments are sold through Komatsu, they qualify for the same finance programs offered on the base loaders. Customer satisfaction is our first priority. Before choosing the attachment from this directory for a specific application, you should consider: 1) The customer application and whether that attachment is designed to perform this application 2) Whether the attachment and machine are sized appropriately for the customer s application and production requirements 3) Whether the attachment width is as wide or wider than the machine width measured over the tires 4) Whether all manufacturers recommendations can be followed, including additional counterweights, guarding and protective devices STATEMENT OF LIMITATION The attachments listed in this directory have not been designed, tested, or manufactured by Komatsu and we assume no responsibility for their performance. The attachment manufacturer is solely responsible for any defects or failures, personal injury or property damage caused by the equipment or its use. All attachment information was supplied by the attachment manufacturers and its accuracy was not verified by Komatsu. The information is being provided for the convenience of our dealers and customers as a general depiction and description of the attachment and its usage. The actual attachment may vary from the information included in this directory. Please check with the manufacturer for the latest specifications. Note: As used herein, "we", "us" or "our" refers to Komatsu America Corp. and its parents, subsidiaries and affiliates. The attachment manufacturer listed on the attachment page is the best source for verification of the above items. Therefore, we recommend that you contact them directly. Alternatively, you can contact your Komatsu territory manager who can, in turn, contact the manufacturer for you. The manufacturer-supplied warranty on these attachments is equal to our warranty period on the base machine. Please note that it is administered by these manufacturers along with parts and service support. The manufacturer index on page 39 provides contact information for each attachment manufacturer.
Table of Contents Worksite Application Choices...................................................... 2 Auger....................................................................... 3-4 Backhoe..................................................................... 5-6 Backhoe - Mini................................................................. 7 Blade - Dozer.................................................................. 8 Boom - Material Handling......................................................... 9 Breaker - Hydraulic............................................................. 10 Broom - Angle................................................................. 11 Broom - General Purpose Pick-Up................................................. 12 Brush Cutter.................................................................. 13 Bucket - Brush Grapple......................................................... 14 Bucket - Forked Scrap Grapple................................................... 15 Bucket - General Purpose........................................................ 16 Buckets - General Purpose Utility & Light Material.................................... 17 Bucket - Heavy Duty Scrap Grapple................................................ 18 Bucket - Multi-Purpose.......................................................... 19 Bucket - Rock................................................................. 20 Cold Planer................................................................... 21 Concrete Claw................................................................ 22 Forks - Pallet................................................................. 23 Grapple - Log Fork............................................................. 24 Hitch - Three Point............................................................. 25 Power Rake................................................................... 26 Preparator................................................................... 27 Rock Wheel................................................................... 28 Roller - Vibratory............................................................... 29 Scarifier..................................................................... 30 Snow Blade................................................................... 31 Snow Blower.................................................................. 32 Stump Grinder................................................................. 33 Tiller........................................................................ 34 Tracks - Over-the-Tire........................................................ 35-36 Tree Spade................................................................... 37 Trencher..................................................................... 38 Manufacturer Index............................................................. 39 1
WORKSITE APPLICATION CHOICES TYPICAL USAGE Common Seldom Attachment Landscape Industrial Construction Agriculture Page No. Auger 3-4 Backhoe 5-6 Backhoe-Mini 7 Blade-Dozer 8 Boom-Material Handling 9 Breaker-Hydraulic 10 Broom-Angle 11 Broom-General Purpose Pick-Up 12 Brush Cutter 13 Bucket-Brush Grapple 14 Bucket-Forked Scrap Grapple 15 Bucket-General Purpose 16 Buckets-Utility/Light Material 17 Bucket-H.D. Scrap Grapple 18 Bucket-Multi-Purpose 19 Bucket-Rock 20 Cold Planer 21 Concrete Claw 22 Forks-Pallet 23 Grapple-Log Fork 24 Hitch-Three Point 25 Power Rake 26 Preparator 27 Rock Wheel 28 Roller-Vibratory 29 Scarifier 30 Snow Blade 31 Snow Blower 32 Stump Grinder 33 Tiller 34 Tracks-Over the Tire 35-36 Tree Spade 37 Trencher 38 Note: Above application recommendations provided by the attachment manufacturers 2
AUGER Woods Equipment Corporation Power Augers: Dig holes up to 36" in diameter with speed and accuracy. Mount design ensures the auger will remain balanced in uneven work conditions. Large 1-1/2-inch plated pivot pins are stronger than competitors models and resist rust. Long-lasting standard auger bits are alloy steel plated; optional cast alloy bits also available. High-flow HA25 & HA30 planetary models are designed for heavy industrial use in hard soil to depths up to 20 feet, depending on conditions. Standard-flow planetary model for 10-foot depths; chain drive units maximize productivity for digging to 5-foot depths. Manufactured by Woods Equipment Corporation Attachment HA15P HA20 HA25 HA30 SK714, SK815, SK818, SK820 SK815, SK818, SK820 - HIGH FLOW * * SK1020, SK1026 SK1020, SK1026 - HIGH FLOW * * Drive Type Planetary Planetary Planetary Planetary Flow Range 10-20 gpm 10-20 gpm 10-30 gpm 10-40 gpm Pressure Range 3500 psi 3500 psi 3500 psi 3500 psi Maximum Bit Size 36" 36" 36" 36" Approximate Weight 300 lb 600 lb 620 lb 650 lb Performance Guide Construction Grade Construction Grade Heavy Duty Heavy Duty * For Low Flow Circuit Continued on Next Page 3
AUGER Woods Equipment Company Continued from Previous Page BIT SPECIFICATIONS Alloy Steel Plate Head Bolt and Lug Dual-Angle Reversible Teeth 2-9/16" round & 2" hex Hubs Standard-Duty (double flight) Size - Diameter x Length* No. of Teeth Approximate Weight 6"x50" 2 54 lb 9"x50" 4 78 lb 12"x50" 4 107 lb 15"x50" 5 117 lb 18"x50" 6 145 lb 24"x50" 8 215 lb 30"x48" 10 280 lb 35"x48" 12 385 lb 24"x50" tree 9 175 lb 30"x48" tree 11 240 lb 36"x48" tree 12 315 lb * Extensions 12", 24", 48" Heavy-Duty (double flight) bits also available 4
BACKHOE Attachment Technologies Inc. The Backhoe has the best bucket digging force for a four-bar linkage backhoe and the highest capacity buckets in its class. The longest reach from the swing post offers the ability to place material farther from the excavation and allows for fewer moves. Increase versatility by adding an optional 12" - 36" wide severe duty bucket with teeth, a fixed or hydraulic knuckle thumb, or a dual acting auxiliary hydraulic kit. Dual-cylinder cushioned swing provides maximum power where it is needed. Swing speed control standard Cushioned swing brings the backhoe to a gentle stop at each end of the swing arc. High clearance swingpost allows operation where clearance is critical. Available with SAE or ISO control pattern. Fixed or hydraulic thumb option converts backhoe into powerful loader for landscaping, land clearing or demolition. Meshes with all 16" to 24" buckets. Optional two-way auxiliary flow hydraulic kit runs hydraulic thumb, coupler, breaker or other hydraulic attachment. Skid steer rear stabilizer attachment may improve performance. Optional vertical stabilizer available. Manufactured by ATI Attachment 509 511 609 611 SK714 SK815 * * SK818, SK820 * * * * SK1020, SK1026 * * * * Transport Height A 7'9" 8'10" 7'9" 8'10" Transport Width 5'0" 5'0" 4'9" 4'9" Ground Clearance B 11" 11" 11" 11" Overall Length C 7'7" 7'9" 7'7" 7'9" Boom Pivot Height 16" 16" 16" 16" Operating Weight w/12" Bucket 1425 lb 1594 lb 1702 lb 1847 lb Digging Depth Maximum D 9'8" 11'1" 9'8" 11'1" Digging Depth (2 ft.) Flat Bottom E 9'7" 11'0" 9'7" 11'0" * For Low Flow Circuit Continued on Next Page 5
BACKHOE Attachment Technologies Inc. Continued from Previous Page K G 60 180 J H C A B 16" 17" E F M D 2' Continued Attachment 509 511 609 611 Digging Depth (8 ft.) Flat Bottom F 8'3" 9'11" 8'3" 9'11" Overall Operating Height - Fully Raised G 12'10" 14'5" 12'10" 14'5" Loading Height H 6'10" 8'0" 6'10" 8'0" Loading Reach J 4'2" 5'0" 4'2" 5'0" Reach From Swing Post K 12'9" 14'5" 12'10" 14'5" Bucket Rotation L 180 180 180 180 Swing Arc 180 180 180 180 Straight Wall Digging Depth M 7'3" 8'2" 7'3" 8'2" Stabilizer Spread Operating Position 7'11" 7'11" 9'11" 9'11" Stabilizer Down Below Grade 16" 16" 17" 17" System Relief Valve Setting 2500 psi 2500 psi 2500 psi 2500 psi Digging Force - Bucket Cylinder 5676 lb 5676 lb 5908 lb 6167 lb Digging Force - Dipper Cylinder 2754 lb 3056 lb 3232 lb 4160 lb 6
BACKHOE MINI FFC Attachments The Mini Backhoe has excellent mobility, and is perfect for digging footings. Easy mounting, no stabilizers required. 3x16 cylinder for powerful breakout force. Fast and easy for trenches up to 5'6" deep. Flat face O-ring seal couplers eliminate leaks. Manufactured by FFC Attachment MB12 MB18 MB24 SK714 * SK815, SK818, SK820, SK1020, SK1026 * * * Digging Depth 5'6" 5'6 5'6" Bucket Width 12" 18" 24" Weight 635 lb 665 lb 695 lb * For Low Flow Circuit 7
BLADE DOZER Attachment Technologies Inc. This Dozer Blade is designed specifically for material handling with heavy-duty construction with a round moldboard and a pre-drilled front to accept a bolt-on edge. Available with standard skid shoe. Hydro-electric controlled angle and tilt, using only one loader valve. Angle and tilt cylinders are interchangeable and equipped with selfaligning bushings. Reversible.75" x 8" bolt-on cutting edge and rolled moldboard.31" thick and 28" high. Blade angles 30 left or right and tilts 10 each way from horizontal. Tilt indicator visible from operator s seat. Flat face O-ring seal couplers eliminate leaks. Manufactured by ATI Attachment DB84 DB96 SK714 SK815, SK818, SK820, SK1020, SK1026 * Width from Centerline to Inside Edge @ 15 Angle 43.53" 49.31" Width from Centerline to Inside Edge @ 30 Angle 42.19" 47.38" Dozer Blade Width @15 Angle 81.13" 92.73" Dozer Blade Width @30 Angle 73.13" 83.56" Width from Centerline to Outside Edge @ 15 Angle 37.63" 43.41" Width from Centerline to Outside Edge @ 30 Angle 30.94" 36.16" Overall Width 84.00" 96.00" Angle Left and Right 30 30 Overall Length 36.68" 36.68" Overall Height 29.89" 29.89" Approx. Weight 1365 lb 1460 lb * For Low Flow Circuit 8
BOOM MATERIAL HANDLING Attachment Technologies Inc. The Material Handling Boom is the perfect piece to complete your landscape tool inventory. Use it to set trees and move cut trees. Also, this boom can handle moving attachments or concrete forms around the job site. Pintle hitch standard. 1500 lb lift capacity. Skid steer rear counterweight attachment recommended for some applications. Manufactured by ATI Attachment MH66 SK714, SK815, SK818, SK820, SK1020, SK1026 Rated Load Capacity 1500 lb Height 66" 9
BREAKER HYDRAULIC These low maintenance Hydraulic Breakers from Komatsu have a high energy transmission and are fully hydraulic in operation. Narrow shape for ease of work in confined areas. Extra long piston stroke. Reliable in-body accumulator. Replaceable tool bushing. Dual rectangular shaped tool retainers. Flat face O-ring seal couplers eliminate leaks. Skid steer special application front door attachment is recommended. Attachment JPB200 JPB210 SK714, SK815, SK818, SK820 * SK1020, SK1026 * CIMA Tool Energy Rating 198 ft lb 212 ft lb Flow Range 17 gpm 22 gpm Striking Rate 1108 bpm 1375 bpm Operating Pressure 1900 psi 2059 psi Working Weight 440 lb 527 lb Striking Rate (blows per minute) 740 min 1040 min Adjusted Breaker Pressure 1750 psi 2000 psi Max. Operating Pressure 1950 psi 2100 psi Tool Diameter 2.5" 2.5" * For Low Flow Circuit 10
BROOM ANGLE Attachment Technologies Inc. Angle Brooms are excellent for cleaning and removing dirt, small rocks, snow and other debris from parking lots, driveways, streets, sidewalks and floors. Moves loose materials ahead and to the side of the broom. Angles 30 left or right. Adjustable down force. Easily adjusted brush settings. Side shifts 10" off center (left or right). Heavy gauge side plates and shell. Inset hydraulic motor for motor protection and better obstacle clearance. Flat face O-ring seal couplers eliminate hydraulic leaks. Poly/wire brush uses more wafers than many competitors. Optional water kit with 25 gallon water reservoir. Optional hydraulic angle kit. Manufactured by ATI Attachment AB72 AB84 SK714, SK815 * SK818, SK820, SK1020, SK1026 * Overall Width 82" 94" Sweeping Width 76" 88" Overall Height 35.5" 35.5" Length Coupler to Brush Front 59.60" 59.60" Transport Height On Stand 40.0" 40.0" Maximum Angle (Left and Right) 30 30 Sweeping Width @ 30 Angle 66" 76" Weight 972 lb 1031 lb Brush Diameter 32" 32" Wafers (Quantity) 38 45 * For Low Flow Circuit 11
BROOM GENERAL PURPOSE PICK-UP Woods Equipment Corporation The General Purpose Pick-Up Broom is excellent for sweeping and scraping dirt, small rocks and other debris from parking lots, driveways, streets, sidewalks and depositing debris in the bucket. Reduces spillage and airborne contaminants. Forward and reverse sweeping directions provide greatest versatility. Bolt-on cutting edge scrapes hard packed mud before sweeping. Heavy gauge side-plate and shelf. Optional gutter broom allows for closer sweeping next to curbs and other vertical surfaces. Flat face O-ring seal couplers eliminate leaks. Sweeps and deposits materials into the bucket for easy removal and dumping. Manufactured by Woods Equipment Corporation Attachment PB68 SK714, SK815, SK818, SK820, SK1020 SK815, SK818, SK820, SK1020, SK1026 - HIGH FLOW * Brush Width 60" Overall Width 68.5" Height 25.25" Length 67.7" Approximate Weight 714 lb Hopper Capacity 13.5 cu. ft. * For Low Flow Circuit 12
BRUSH CUTTER FFC Attachments Brush Cutter cuts undergrowth and brush while mulching with an added feature of a stump jumper. 1/4" deck thickness. High speed one direction blade with a cutting capacity of 3". Automatic hydraulic blade shut-off, no hold down chains or cables to contend with. One direction lift. Front chain guard/rear roller with tapered roller bearings. Single motor hydraulic drive. Optional front caster wheels. Manufactured by FFC Attachment LAF3748 LAF3760 LAF3772 SK714, SK815 SK818, SK820 SK1020, SK1026 Overall Width 51.5" 63.5" 75.5" Cutting Width 48" 60" 72" Height 27" 27" 27" GPM range 15-30 gpm 15-30 gpm 15-30 gpm Max PSI range 3500 psi 3500 psi 3500 psi Blade Speed Min/Max 8316/12751 ft/min 10395/15939 ft/min 12474/19127 ft/min Weight, Approx. 1324 lb 1464 lb 1653 lb 13
BUCKET BRUSH GRAPPLE Attachment Technologies Inc. Brush Grapple Buckets performs many jobs in one. In a single pass, rake away debris, keep it in a manageable pile, move it around with ease, or use it to backfill. Load or pile logs, brush, rocks, demolition debris, and many other types of materials. Dual independent see-through grapples. Helix tooth design to aid in pulling the work into the bucket. Complete protection for cylinders (top, bottom and outboard sides). Double pilot-operated check valve for locking grapple into position. Hydraulic hose protection and seclusion (hoses route immediately into top cross tubing). Pivot pins have lubrication capabilities. Flat face O-ring seal couplers eliminate leaks. Skid steer rear counterweight attachment recommended for some applications. Manufactured by ATI Attachment BG72 BG84 SK714 * SK815, SK818, SK820 * * SK1020, SK1026 * Overall Width 72" 84" Overall Depth 35.9" 35.9" Grapple Width 20.5" 20.5" Tine Spacing 6" 6" Grapple Height - Closed 26.4" 26.4" Grapple Hook - Opening 42" 42" Overall Weight (lbs) 794 lb 826 lb Clamping Force (lbs) 1250 lb 1250 lb Number of Grapple Teeth 4 4 Number of Cylinders 2 2 Tines & End Plates 1/2" T1 Steel (100,000 lb yield) 1/2" T1 Steel (100,000 lb yield) Bore 2.00" 2.00" Stroke 8.25" 8.25" Rod Diameter 1.25" 1.25" * For Low Flow Circuit 14
BUCKET FORKED SCRAP GRAPPLE FFC Attachments The Forked Scrap Grapple Bucket is great for brush and refuse removal. In addition to enclosed cylinders, our grapple bucket also offers enclosed hoses for added protection on the job site. Load loose material while leaving dirt behind. Grapples work independently to handle uneven loads. Heat-treated tines. Cylinder guard standard. Flat face O-ring seal couplers eliminate leaks. Skid steer rear counterweight attachment recommended for some applications. Manufactured by FFC Attachment FSG63 FSG72 SK714 SK815, SK818, SK820, SK1020, SK1026 * * Opening Height 41" 41" Height Closed 20" 20" Usable Tooth 24.13" 24.13" Width 63.44" 73.06" Number of Teeth 8 10 Approximate Weight 990 lb 1100 lb Cylinder Bore 2" 2" Cylinder Stroke 8" 8" * For Low Flow Circuit 15
BUCKET GENERAL PURPOSE Woods Equipment Corporation General Purpose Bucket is ideal for medium to heavy load and carry, general construction and excavating type work. Choose between the long or short-lip design. The long-lip design provides increased visibility and maximum capacity while the short lip design provides maximum breakout force. The heavy-duty construction utilizes no internal gussets or obstructions. Round design moldboard offers maximum loading and unloading capabilities with higher capacities for light material handling applications. The square back profile allows for reverse grading. A pre-drilled front edge will accept a bolt-on edge. Available with welded Hensley tooth adapters. width Toothbar Option Bucket with factory-installed bolt-on edge available. Skid steer rear counterweight attachment recommended for some applications. Manufactured by Woods Equipment Corporation Attachment GP61S GP68S GP73S GP61L GP68L GP73L SK714-5 SK815-5, SK818, SK820 SK1020, SK1026 Type of Bottom Short Short Short Long Long Long Width 61" 68" 73" 61" 68" 73" Height 19" 19" 19" 19" 19" 19" Length 29" 29" 29" 35" 35" 35" Approximate Weight 404 lb 440 lb 469 lb 439 lb 475 lb 508 lb Heaped Capacity 11 cu ft 13.4 cu ft 14.4 cu ft 14.8 cu ft 16.5 cu ft 17.8 cu ft Optional Teeth weld-on weld-on weld-on weld-on weld-on weld-on Optional Bolt-on Cutting Edge 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible Optional Bolt-on Toothbar Inside Bucket Width 59-3/8" - 59-3/4" 66-3/8"- 66-3/4" 71-3/8"- 71-3/4" 59-3/8"- 59-3/4" 66-3/8"- 66-3/4" 71-3/8"- 71-3/4" 16
BUCKETS GENERAL PURPOSE UTILITY & LIGHT MATERIAL Woods Equipment Corporation General Purpose Utility Buckets are ideal for light to medium material load and carry operations. The Light Material Buckets are primarily for low density material such as woodchips, mulch, fertilizer, snow and other light aggregate. Heavy-duty construction utilizes no internal gussets or obstructions. Round design moldboard offers maximum loading and unloading capabilities and higher capacities for light material handling applications. The square back profile allows for reverse grading. A pre-drilled front edge will accept a bolt-on edge. Bucket with factory-installed bolt-on edge available. width Toothbar Option Bucket with welded Hensley tooth adapters available (utility only). Skid steer rear counterweight attachment recommended for some applications. Manufactured by Woods Equipment Corporation Attachment UT66 UT72 LM66 LM72 LM78 LM84 SK714-5 SK815-5, SK818, SK820 SK1020, SK1026 Type GPU GPU LM LM LM LM Width 66" 72" 66" 72" 78" 84" Height 25" 25" 26" 26" 26" 26" Length 35" 35" 38" 38" 38" 38" Approximate Weight 513 lb 553 lb 543 lb 585 lb 617 lb 660 lb Heaped Capacity 20.8 cu ft 22.8 cu ft 23.5 cu ft 25.8 cu ft 28.1 cu ft 30.3 cu ft Optional Bolt-on Cutting Edge 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible Optional Bolt-on Toothbar 64-3/8"- 70-3/8"- not not not not Inside Bucket Width 64-3/4" 70-3/4" recommended recommended recommended recommended 17
BUCKET HEAVY DUTY SCRAP GRAPPLE Woods Equipment Corporation Heavy Duty Scrap Grapple Buckets are designed to handle oddly-shaped objects such as railroad ties, trees, rocks, debris, and other demolition scrap. High strength design provides for longer service life. Double grapples maximize load handling capabilities. Pre-drilled front edge will accept a bolt-on edge. Flat face O-ring seal couplers eliminate leaks. Available with factory-installed bolton edge. Skid steer rear counterweight attachment recommended for some applications. Manufactured by Woods Equipment Corporation Attachment SG66 SG72 SG78 SK714 SK815, SK818, SK820 - HIGH FLOW * * SK1020 SK1020, SK1026 - HIGH FLOW * * Width 66" 72" 78" Height 28" 28" 28" Length 27-1/4" 27-1/4" 27-1/4" Capacity 12.9 cu ft 14 cu ft 15.2 cu ft Approximate Weight 826 lb 856 lb 886 lb Cylinder Bore Diameter 2" 2" 2" Cylinder Stroke 8-1/4" 8-1/4" 8-1/4" Optional Bolt-on Cutting Edge 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible * For Low Flow Circuit 18
BUCKET MULTI-PURPOSE Woods Equipment Corporation The Multi-Purpose Bucket is a versatile, multiple use tool for grading, dozing, clamping, loading, high dumping, and scraping. Like having four attachments in one. Its heavy-duty construction and industrial strength cylinders and cutting edges provide a long life for landscaping, municipal, construction or demolition jobs. A bolt-on replaceable dozer edge is standard. A pre-drilled front edge will accept a bolt-on edge. Flat face O-ring seal coupler eliminates leaks. Bucket with factory-installed bolt-on cutting edge available. width Bucket with welded Fabco crimp-on tooth adapters available. Toothbar Option Skid steer rear counterweight attachment recommended for some applications. Manufactured by Woods Equipment Corporation Attachment MP60 MP66 MP73 MP78 SK714 SK815, SK818, SK820 SK815, SK818, SK820 - HIGH FLOW * * SK1020, SK1026 SK1020, SK1026 - HIGH FLOW * * Width 60" 66" 73" 78" Height 31" 31" 31" 31" Length 33" 33" 33" 33" Heaped Capacity 11.5 cu ft 12.8 cu ft 14.2 cu ft 15.5 cu ft Approximate Weight 529 lb 582 lb 644 lb 688 lb Cylinder Rod Diameter 1-1/2" 1-1/2" 1-1/2" 1-1/2" Cylinder Bore 2-1/2" 2-1/2" 2-1/2" 2-1/2" Cylinder Stroke 8" 8" 8" 8" Optional Bolt-on Reversible Cutting Edge 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible 5/8" x 8" reversible Optional Bolt-on Toothbar Inside Bucket Width 58-3/8"- 58-3/4" 64-3/8"- 64-3/4" 71-3/8"- 71-3/4" 76-3/8"- 76-3/4" * For Low Flow Circuit 19
BUCKET ROCK Attachment Technologies Inc. Rock Buckets are designed to rake, pile and load debris from construction sites, pastures, fields and other areas. Cradles the collected rocks and debris while additional material is being collected. Tine spacing determines the size of the rocks and debris that will be retained while allowing the soil to sift back to the ground. The rake design is used to gather material away from buildings and obstructions, for faster clean up of debris, to level out clumps of dirt and to pick up pieces of sod. Manufactured by ATI Attachment RB66 RB75 SK714 * SK815, SK818, SK820, SK1020, SK1026 * Overall Width 65.85" 74.35" Overall Depth 42.45" 42.45" Depth with Skid-Steer Mounting 49.80" 49.80" Overall Height 21.77" 21.77" Tine Spacing (Center to Center) 4.25" 4.25" Tine Spacing (Between Tines) 3.125" 3.125" Overall Weight (lbs) 550 lb 619 lb Number of Tines 16 18 Tine Rod Diameter 1.125" 1.125" 20
COLD PLANER Woods Equipment Corporation Cold Planers are used for concrete and asphalt road repair, opening trenches for utility work, milling bridge decks and removing cracks and bumps. Top pivot design self levels the drum and chassis creating higher downforces, precise depth control and easier operation. Wheels on the drum chassis minimize the changes of gouging the asphalt. Side skids reduce the possibility of the wheels dropping into the cut when milling potholes or making butt joints. Cutting drum is driven through a planetary gearbox. Electrohydraulic tilt depth and sideshift control eliminate difficult manual adjustments and is standard on all models. Hinged top cover permits easy access for pick maintenance. Chassis design allows drum installation or removal in 60 minutes or less. Flat face O-ring seal couplers eliminate leaks. Skid steer rear counterweight attachment recommended for some applications. Manufactured by Woods Equipment Corporation Attachment CP12 CP16 CP18 CP24 CP30 SK714, SK815, SK818, SK820, SK1020, SK1026 SK815, SK818, SK820 - HIGH FLOW SK1020, SK1026 - HIGH FLOW Depth of Cut 0-6" 0-6" 0-6" 0-6" 0-6" Width of Cut 12" 16" 18" 24" 30" Number of Teeth 28 50 56 70 77 Sideshift 22" 22" 22" 22" 22" Tilt 19 19 19 15 11 Weight 1200 lb 1750 lb 2000 lb 2300 lb 2450 lb Hydraulic Depth Control STD STD STD STD STD Hydraulic Tilt Control STD STD STD STD STD 21
CONCRETE CLAW FFC Attachments Concrete Claw removes concrete on sidewalks, driveways or any construction sites. Replaceable points. End plates and tooth shanks are made with high strength T-1 steel. 1" x 8" wear resistant Pacal steel tapered cutting edge. Features name-brand replaceable points with 1-1/2" wide shanks. Rubberized flex pins securely fasten replaceable points. Manufactured by FFC Attachment 10024 SK714, SK815, SK818, SK820, SK1020, SK1026 Working Width 24" Working Depth 48" Height OD 21" Rear Opening Height 7.5" Weight, Approx. 575 lb 22
FORKS PALLET Attachment Technologies Inc. Pallet Forks are designed and constructed specifically for heavy duty applications. This essential tool easily transports bulky, baled or palletized materials. Rail type, double lock down provides protection from load shifting. Certified forged teeth increase strength and service life. Backguard allows for greater operator visibility. Skid steer rear counterweight attachment recommended for some applications. Manufactured by ATI Attachment PF48 SK714, SK815, SK818, SK820, SK1020, SK1026 * Weight (including mounting) 370 lb Fork Length 48" Fork Capacity 4000 lb Fork Spread Range 4-3/8-40-3/8" High Visibility Back Guard yes Tooth Double Lock Downs yes 23
GRAPPLE LOG FORK FFC Attachments The Log Fork Grapple is an excellent attachment for handling logs, pipes, brush, and other bulky materials. 2" x 8" hydraulic cylinder. Closes to 6" log or pipe. Flat face O-ring seal couplers eliminate leaks. Skid steer rear counterweight attachment recommended for some applications. Manufactured by FFC Attachment LG28 SK714, SK815, SK818, SK820, SK1020, SK1026 SK815, SK818, SK820, SK1020, SK1026 - HIGH FLOW * Tine Length 28.4" Opening Height 43.1" Capacity 6400 lb Weight 610 lb * For Low Flow Circuit 24
HITCH THREE POINT Woods Equipment Corporation A Three Point Hitch is necessary for adapting certain attachments to Komatsu skid steer loaders. Adapts 3 point hitch, category 1 attachments to skid steer loaders. Landscape rakes, box scrapers, pulverizers and more are skid steer loader compatible. Manufactured by Woods Equipment Corporation Attachment TH3000 SK714, SK815, SK818, SK820, SK1020, SK1026 Overall Width 46" Height 26" Length 11" Approximate Weight 180 lb 25
POWER RAKE FFC Attachments Power Rakes efficiently handle the toughest landscape tasks - finish grading, pulverizing, debris removal, spreading soil or filling, and de-thatching. All-purpose versatile grading and cleaning tool. It is designed to facilitate lawn de-thatching, seedbed preparation, turf removal, and highway shoulder reclamation. Pulverize dirt clods while keeping rocks and debris ahead of the rolling action. Produce perfect beds for sodding, seeding, and much more. Bi-directional drum works soil forward and backwards, removing rocks and debris, preparing soil for sod or seed. Dual motor design delivers more power for faster cycles. Heavy-duty carbide teeth. Direct drive motor reduces maintenance. Heavy-duty frame extends life. Low height improves visibility. Available with manual or hydraulic angling of 20 degrees. Manufactured by FFC Attachment PRA72 PRR72 PRA90 PRR90 SK714, SK815, SK818, SK820 * * SK1020, SK1026 * * Working Width 72" 72" 90" 90" Overall Width 83" 83" 101" 101" Fully Angled Width 68" NA 86" NA Height 30" 30" 30.3" 30.3" Angle Option Manual / Hydraulic NA Manual / Hydraulic NA Weight 1000 lb 850 lb 1075 lb 925 lb * For Low Flow Circuit 26
PREPARATOR FFC Attachments The Preparator attacks the toughest ground condition, collects rocks and debris from 1" to 20" in diameter, and tills compacted soil to create a perfect seedbed. The adjustable rolling drum conditions the soil and carries debris into its perforated bucket. Short couple design allows good visibility of the surrounding worksite. Rotating drum carries rocks and debris into its bucket while leaving the soil ready to be planted. Perforated bucket floor allows dirt to sift through. Powerful rotating drum conditions soil with the scarifying action of A-R 400 steel teeth. Heavy-duty drum is designed to withstand the abuse of rocky working conditions. Variable speed motor and bi-directional drum capable of tilling and fluffing the soil as well as raking and grooming. Floating-head design allows it to follow ground contours while picking up rocks from 1" to 20" in diameter for virtually debris-free soil preparation. Spring tines work to eliminate skid shoe tracks. Manufactured by FFC Attachment P54 P66 P76 SK714 * SK815, SK818, SK820 * SK1020, SK1026 * Bucket Capacity 8.86 cu ft 10.32 cu ft 12.5 cu ft Overall Width 63.75" 75.25" 85.25" Bucket Swath Width 54" 66" 76" Overall Bucket Height 25.53" 25.53" 25.53" Overall Bucket Length 53" 53" 53" RPM-r/min @ 16 gpm Nominal Flow 0-100 0-100 0-100 Overall Drum Diameter 21.5" 21.5" 21.5" Tooth Thickness.19".19".19" Tooth Length 2.19" 2.19" 2.19" Number of Teeth 250 300 340 Rake Drive #80H Roller Chain #80H Roller Chain #80H Roller Chain Brush Drive #50H Roller Chain #50H Roller Chain #50H Roller Chain Overall Weight 976 lb 1270 lb 1465 lb * For Low Flow Circuit 27
ROCK WHEEL Woods Equipment Corporation The Rock Wheel is ideal to cut utility lines for gas, sewer, water, electrical, cable installation and repairs. Other applications include asphalt patch cuts and creating expansion joints in roadways. Gauge skid sets cutting depths and minimizes extra passes for more precise control. Electro-hydraulic side shift allows rockwheel to move from the center to the operator s right for placement of the cutting wheel at the desired position. Planetary wheel drive reduction generates higher torque for fast asphalt patch or roadway expansion joint cuts. Optional 20 or 50 gal. water kit. Skid steer rear counterweight attachment recommended for some applications. Manufactured by Woods Equipment Corporation Attachment RW12 RW18 RW24 SK815, SK818, SK820 - HIGH FLOW SK1020, SK1026 - HIGH FLOW Depth of Cut 0-12" 0-18" 0-24" Width of Cut 2.5/4.5" 2.5/4.5" 2.5/4.5" Number of Teeth 28/33 42/44 56/66 Side Shift 22" 22" 22" Weight 1600 lb 1800 lb 2100 lb Wheel Speed 60 rpm 60 rpm 60 rpm Cutting Speed up to 15 fpm up to 15 fpm up to 15 fpm 28
ROLLER VIBRATORY Woods Equipment Corporation Smooth drum Vibratory Rollers are used for compaction of granular material such as sand, gravel and stone prior to asphalt or concrete curbing. Padded drum vibratory rollers are used for compacting clay material. Easily maneuvered in tight spaces where larger units will not fit; ideal for smaller compaction jobs, near foundations and foliage. Half the cost of self-propelled, walkbehind, or ride-on models; self lubricating bearings reduce maintenance. Drum and shaft bearings lubricated in oil bath; isolators on roller eliminate vibration in cab. Padded sheepsfoot drum penetrates heavy soils for effective compaction of cohesive and clay materials. Low flow hydraulic design allows full roller function and maximum compaction at only 15 gpm. Manufactured by Woods Equipment Corporation Attachment VR48A VR66A VR73A SK714, SK815, SK818, SK820 SK815, SK818, SK820 - HIGH FLOW * * SK1020, SK1026 SK1020, SK1026 - HIGH FLOW * * Drum Width 48" 66" 73" Overall Width 55.5" 73" 80.5" Drum Oscillation ±15 ±15 ±15 Overall Height 27" 27" 27" Overall Length 33" 33" 33" Drum Diameter 24" 24" 24" Total Output 7140 lb 8740 lb 10,240 lb Frequency VPM 2000 @ 15 gpm 2000 @ 15 gpm 2000 @ 15 gpm Weight lbs. Smooth 1450 lb 1633 lb 1762 lb Weight lbs. Padded 1600 lb 1850 lb 2100 lb * For Low Flow Circuit 29
SCARIFIER Woods Equipment Corporation Scarifier is ideal for loosening hard-packed soil for landscape preparation or loosening asphalt prior to removal. Built rugged for tough, heavy-duty applications Manufactured by Woods Equipment Corporation Attachment SF3000 SK714, SK815, SK818, SK820, SK1020, SK1026 Working Width 40" Overall Width 63" Height 27" Length 20" Approximate Weight 350 lb Number of Shanks 5 30
SNOW BLADE FFC Attachments Snow Blades are designed for moving snow or light dirt quickly. Hydraulic angle 30 max. in either direction. Reversible and replaceable wear edge. Adjustable skid shoes. Spring loaded trip mechanism. 7 gauge steel blade. Heavy structural steel frame. Manufactured by FFC Attachment SB72 SB84 SB96 SK714 SK815, SK818, SK820 SK1020, SK1026 Length 72" 84" 96" Height with Edge 23.25" 23.25" 23.25" Angled Width 62.1" 72.5" 82.9" Weight 475 lb 500 lb 525 lb * For Low Flow Circuit 31
SNOW BLOWER FFC Attachments This Snow Blower, with a two-stage hydraulic blower, throws snow up to 35'. Spout will rotate 280 degrees. Electronically-controlled, poly-lined chute and deflector. High volume shroud opening. Excellent visibility. Wear-resistant Pacal steel tapered wear edge, 3/8"x3". 12 gauge reinforced wrapper. Adjustable skid shoes. Manufactured by FFC Attachment 60 72 72H 84 84H SK714 SK815, SK818, SK820 SK815, SK818, SK820 - HIGH FLOW * * SK1020, SK1026 * SK1020, SK1026 - HIGH FLOW Cutting Width 60" 71.5" 72" 84" 84" Shroud Opening 24.5" 24.5" 36" 25" 36" Overall Depth 35.7" 35.5" 43" 38" 43" Overall Height 56.75" 56.75" 74" 56.75" 74" Weight 650 lb 685 lb 1150 lb 720 lb 1230 lb * For Low Flow Circuit 32
STUMP GRINDER Woods Equipment Corporation Stump Grinders for stump grinding in residential, commercial, and agricultural areas. Grinding arm swings a full 140 / 60 inches to level large diameter trees; telescopes 7 inches to minimize repositioning of the skid steer. Hydraulic controls manage swing, depth and extension for easy operation in tight areas. Higher productivity via 16-inch cutting depth and quick-attach bracket. More cost effective than tow-behind models, no engine, belts, or tires to maintain. More maneuverable than tow-behind models; goes into areas not accessible by truck. 3.25 inches wide cutting head with carbide teeth, levels stumps in minutes. Flat face O-ring seal couplers eliminate leaks Skid steer special application front door attachment is recommended. Manufactured by Woods Equipment Corporation Attachment SG20 SG40 SG60 SK714, SK815, SK818, SK820 SK815, SK818, SK820 - HIGH FLOW * SK1020, SK1026 SK1020, SK1026 - HIGH FLOW * Overall Length 64.1" 64.1" 64.1" Telescopic Extension 7" 7" 7" Horsepower Delivered To 20 HP To 40 HP To 60 HP Cutting Height Above Ground 21" 21" 21" Cutting Depth Below Ground 16" 16" 16" Cutting Wheel Width 3.25" 3.25" 3.25" Cutting Width 60" 60" 60" Swing Range 140 140 140 Type of Teeth 0.5" slanted, carbide tip 0.5" slanted, carbide tip 0.5" slanted, carbide tip Number of Teeth 32 32 32 Wheel Diameter 18" 18" 18" Wheel Speed (Approx..) 700 rpm 900 rpm 900 rpm Weight 765 lb 775 lb 840 lb * For Low Flow Circuit 33
TILLER Woods Equipment Corporation Tillers are used for mixing soils to improve seed beds and stabilize soil. Other applications include tilling construction sites and homesites prior to landscaping. Bi-directional tine rotation allows unit to operate at maximum effectiveness with loader moving forward or backward. Dual direct drive motor design eliminates the need for sprockets and chains and the required lubrication of these components. Offset mounting configuration allows right loader tracks to be covered when operated in reverse for finish tilling operations. Drive motors are recessed in the chassis which allows unit to be operated near obstacles such as fences or buildings. Hardened, replaceable tines engineered for extended life and easy replacement. Flat face O-ring seal couplers eliminate leaks Manufactured by Woods Equipment Corporation Attachment TL52 TL73 TL84 SK714, SK815, SK818, SK820 SK815, SK818, SK820 - HIGH FLOW * SK1020, SK1026 SK1020, SK1026 - HIGH FLOW * Overall Width 60" 86" 97" Cutting Width 52" 73" 84" Working Depth 6" 6" 6" Overall Height 31" 31" 31" Number of Tines 28 36 40 Tine Rotation Bi-directional Bi-directional Bi-directional Weight 760 lb 1050 lb 1228 lb Driveline (2) In-line gerotor motors (2) In-line gerotor motors (2) In-line gerotor motors Maximum Tine Speed 121 rpm 121 rpm 121 rpm Max Flow 15 gpm @ 2000 psi 25 gpm @ 2000 psi 46 gpm @ 3500 psi * For Low Flow Circuit 34
TRACKS OVER-THE-TIRE Grouser Products Over-The-Tire Tracks can be installed and removed easily and efficiently for improved traction, tire strength and protection on Komatsu Skid Steer Loaders in soft, muddy, sandy or abrasive conditions. Cross Bar Track Reduces ground pressure by as much as 50%. 1-1/4" hardened replaceable bushings. Run loose design to prevent strain on loader drive system. Built-in length adjustment. Self-cleaning. Adds counterweight. Replaceable components. Hard Shoe Track Open bar design provides maximum traction and flotation. Open side plate provides excellent cleaning in the pivot areas. Field serviceable and rebuildable. Soft Shoe Track Manufactured by Grouser Products SK714-5 Track Type Track Width Part Weight Wheel Base Tire Size Standard Tires Cross-Bar 13.25" 861 lb 37.4" 10.00 x 16.5 Wide Tires ** Cross-Bar 17.50" 974 lb 37.4" 31 x 15.5-15 (4) Wheel Spacers for Wide Tires 75 lb Standard Tires Hard Shoe 13.25" 1016 lb 37.4" 10.00 x 16.5 Standard Tires Soft Shoe 13.25" 924 lb 37.4" 10.00 x 16.5 SK815-5 thru SK820-5 Track Type Track Width Part Weight Wheel Base Tire Size Standard Tires Cross-Bar 13.25" 911 lb 41.3" 10.00 x 16.5 Wide Tires*** Cross-Bar 17.50" 1031 lb 41.3" 31 x 15.5-15 (4) Wheel Spacers for Wide Tires 75 lb Standard Tires Hard Shoe 13.25" 1058 lb 41.3" 10.00 x 16.5 Standard Tires Soft Shoe 13.25" 962 lb 41.3" 10.00 x 16.5 Continued on Next Page 35
TRACKS OVER-THE-TIRE Grouser Products Continued from Previous Page SK1020-5, SK1026 Track Type Track Width Part Weight Wheel Base Tire Size Standard Tires Cross-Bar 14.75" 1018 lb 45.8" 12.00 x 16.5 Standard Tires Hard Shoe 14.75" 1335 lb 45.8" 12.00 x 16.5 Standard Tires Soft Shoe 14.75" 1284 lb 45.8" 12.00 x 16.5 APPLICATION CHART Soft and Muddy Job Site Conditions Cross-Bar Track Hard Shoe Track Soft Shoe Track Muddy and Sandy Job Site Conditions Concrete or Asphalt Job Site Surfaces Rocky, Gravel or Abrasive Job Site Conditions 36
TREE SPADE FFC Attachments A Tree Spade can be used in planting, moving or transplanting trees and shrubbery. Other uses include placing large decorative rocks and stones. Completely transplant trees and shrubbery. Dig holes for incoming trees. Transplant pre-packaged trees. Place trees in new location. Easier to position plants. 3/8" plate with sharp, tapered edge. Place large decorative rocks and stones. Skid steer rear counterweight attachment recommended for some applications. Manufactured by FFC Attachment TS36 TS40 TS42 TS44 TS48 SK714-5 SK815-5, SK818-5, SK820, SK1020, SK1026 Maximum Ball Size 36" 40" 42" 44" 48" Weight 258 lb 312 lb 360 lb 378 lb 425 lb 37
TRENCHER Attachment Technologies Inc. Trenchers are ideal for all types of utility and footer trenches. High torque hydraulic motor for maximum digging power. 2" pitch, anti-back flex chain for maximum performance and life. Double standard chain for tooth pattern versatility. Heavy-duty chain reduction drive system amplifies torque to cutting chain. Sealed idler bearing is maintenance free. Low profile dirt shield for better operator visibility. Built-in skid shoe to provide positive depth control for auger. Pivoting crumber shoe and bar to assist with loose soil removal. Bolt-on replaceable wear strips on boom extends boom life under rough conditions. Manufactured by ATI Attachment 615 625 650C SK714 * ** SK714, SK815, SK818, SK820, SK1020, SK1026 * SK815, SK818, SK820, SK1020, SK1026 - HIGH FLOW * Boom Size 36" 36" 30" 36" 48" 30" 36" 48" 60" Trench Depth @ Recommended Angle 36" 36" 30" 36" 48" 30" 36" 48" 60" Chain Widths Available 6" 6" 6", 8", 10", 12" 6", 8", 10", 12" 6", 8" 6", 8", 10", 12" 6", 8", 10", 12" 6", 8" 6" Recommended Trenching Angle 65 65 65 65 65 65 65 65 65 Length 65" 65" 66" 73" 86" 58" 71" 84" 97" Width 42" 50.5" 53" 53" 53" 43" 43" 43" 43" Height 28" 28" 32" 32" 32" 37" 37" 37" 37" Spoil Discharge Reach 24" 24" 18" 18" 18" 27" 27" 27" 27" Weight 495 lb 775 lb 1040 lb 1200 lb * For Low Flow Circuit ** For Low Flow Circuit/Side Shift Option 38
Manufacturer Index Attachment Technologies Inc. Delhi, IA 52223 Phone: (800) 922-2981 FFC Attachments Lee, IL 60530 Phone: (800) 747-2132 Grouser Products West Fargo, ND 58078 Phone: (800) 747-6182 Woods Equipment Corporation Oregon, IL 61061 Phone: (815) 732-2141 39
NOTES
NOTES
KUSS151-02 2005 Komatsu Printed in USA D(5M)CCI 4/05 (EV-1) 440 N. Fairway Dr. Vernon Hills, IL 60061 www.komatsuamerica.com Materials and specifications are subject to change without notice is a trademark of Komatsu Ltd. Japan