Extrusion Pumps and Accessories

Extrusion Pumps and Accessories

2 ARO Extrusion Pumps and Accessories

Numerical Index MODEL PAGE MODEL PAGE MODEL PAGE MODEL PAGE 128121-800 24 650542-1 11 651537-1 22 66731 18 129121-400 24 650543-1 11 651612-X 17 66731-X 18 2085 23 650683-X4X 35 651613-B 14 66732 18 23644-400 25 650684-X4X 44 651614-X 17 66732-X 18 28353 24 650685-X4X 46 651615-B 14 67073 14 62274 24 650691-X43-B 37 651616-X 15-16 67120-P4X 41 628088-7 14 650692-X43-B 45 651616-XX 15-16 67121-P4X 42 628089-X 14 650871-XX4-B 30 651729 24 67133 16 635040 25 650875-XX4-B 31 651780-XXX-B 21 67134 20 635043 25 650883-X4X 40 651790-XXX-B 21 67136 20 635106 23 650891-X47-B 43 651840-X 18 67189 14 635108 23 650935-X43-C 48 651841-1 18 67195-X 19-20 635117 23 650941-XX4-B 47 651842-1 18 67196-X 20 636075 23 650971-X44-B 38 65940 24 76751 23 636077 23 65138 14 66248 19 91363-10 20 636080 23 65139 14 66248-1 19 91364-10 18 636085 23 651412 22 66333-B 25 91790 25 636086-B 23 651412-X 22 66334-B 25 92460 25 636087-B 23 651418-XXX-B 22 66353-1 16 C28241-810 24 636088 23 651420-XX 22 66354-1 16 NM2322E-11-P4X 33 641523-1 23 651420-XXX 22 66469 18 NM2322F-11-P4X 34 650483-X4X 28 651421-XXX 22 66516 19 NP322L01-1 8 650484-X4X 32 651422-XXX 22 66516-X 19 NP322L02-1 8 650485-X4X 39 651500 23 66517 19 NP322R01-1 9 650491-X43-B 29 651511 22 66517-X 19 NP322R02-1 9 650492-4X3-B 36 651513-11-B 22 66541-X 22 NP443R01-1 11 650540-1 10 651533 23 66541-XX 23 P29241-610 24 650541-1 10 651536-1 22 66718 25 3 Table of Contents MODEL PAGE MODEL PAGE Extrusion Data: 4 Extrusion Accessories: 14-25 Typical Application: 5 Steps To Order The Right Pump 26-27 Model Reference Index: 6-7 Individual Pump Models 28-48 Extrusion Packages: 8-13

4 Extrusion Pumps Extrusion pumps are frequently put in the most difficult of applications moving high viscosity fluids that are often abrasive. Extrusion pumps are used to apply a bead of material. In some instances the pump supplies a continuous bead; other applications call for intermittent delivery. Typical highviscosity fluids pumped include caulkings, heavy lubricants, mastics, sealers and inks. Application Parameters Viscosity can be the largest obstacle in an extrusion application. As viscosities increase, fluid flow decreases. In general, 2-ball pumps can be used for fluids with viscosities up to 50,000 cps. Chop-check pumps are used for higher viscosity fluids. Pump ratios used in extrusion applications range from 9:1 to 70:1. Additional equipment is needed to keep an extrusion pump primed. Follower plates, lifts and rams force the material into the pump inlet. Without this equipment, the fluid will not flow into the pump. Lifts can be used for fluids with viscosities up to 200,000 cps. Rams are needed for fluids with higher viscosities. If a fluid is stringy, a Ram may be needed for fluids with viscosities as low as 60,000 cps. Extrusion pumps also use fluid mass to keep the pump primed. When bulk tanks are used, the weight of the fluid will push it into the pump inlet. Accessories Required Extrusion Information Several accessories will improve the efficiency of an Extrusion application. They include: Follower Plates: Seal fluid container to maintain pump prime. Plates mount directly to pump inlet. Fluid is forced into pump. Available for 19 litre pails and 208 litre drums. Follower Seals: Forms seal between Follower Plate and Container to maintain prime. Available in Single or Double Lip Models. Use Single-Lip Wiper for viscosities up to 300,000 cp. Double Lip Wiper provides better wiping action on higher viscosity fluids. Use Double-Lip Wipers for fluid viscosities over 300,000 cp. Lifts: Eases changeover of empty containers. An internal cylinder lifts the pump from the container. Weight of air motor, pump and mounting bracket maintain pump prime. Used on medium to high viscosity fluids. Available for 208 litre drums. Rams: Function like a lift, but also exert downward force. An internal piston pushes the pump inlet into the fluid. Available in single or two-post configurations, for 19 or 208 litre containers. Used on medium to high viscosity fluids. Portability Kits: For single-post ram mounted pumps. Wheels bolt onto base of ram. Eases portability of unit around application site. Floor Mounts: Used when fluid is stored in large, bulk containers. Gravity feeds material into the pump inlet. Locate as close to fluid container as possible. Downstream Fluid Regulators: Used to control fluid pressure beyond the regulator. Downstream regulators cut fluid pressure to desired level. Also used to eliminate pulsation created by pump cycling. Extrusion Guns: Used to dispense fluids with viscosities above 200,000 cps. Available in manual or automatic configurations. Snuff-back guns eliminate drippage at work site. Extrusion Nozzle Kit: For manual or automatic extrusion guns. Size of orifice diameter controls size of bead extruded with the gun.

Typical Extrusion Applications: 5 1 4 2 5 6 3 10 9 7 8 Typical Transfer Accessories: I.D. DESCRIPTION: See Page Number 1 2 3 4 5 6 7 8 9 10 F-R-L Kit Assembly 24 ARO-STOP Over-run Control 25 Two Post Ram 14-17 Downstream Fluid Regulator 21 Automatic Extrusion Gun 22 Extrusion Gun Nozzle Kit 22-23 Single Post Ram 14 Z Swivel 23 Manual Extrusion Gun 23 Extrusion Nozzle Kit 22-23 Extrusion Information

6 Ratio: Max. Flow Rate: Model Number: Pump Material: Pump Type 11:1 13.9 l/min 650483-X4X Stainless Steel 2-Ball 12:1 12.4 l/min 650491-X43-B Carbon Steel Chop Check 13:1 39.6 l/min 650871-XX4-B Carbon Steel Chop Check 20:1 39.6 l/min 650875-XX4-B Carbon Steel Chop Check 22:1 7.2 l/min 650484-X4X Stainless Steel 2-Ball 22:1 3.7 l/min NM2322E-11-P4X Carbon Steel Chop Check 22:1 3.7 l/min NM2322F-11-P4X Stainless Steel Chop Check 23:1 13.7 l/min 650683-X4X Stainless Steel 2-Ball 23:1 6.8 l/min 650492-X43-B Carbon Steel Chop Check 23:1 12.4 l/min 650691-X43-B Carbon Steel Chop Check 30:1 39.6 l/min 650971-XX4-B Carbon Steel Chop Check 30:1 4.9 l/min 650485-X4X Stainless Steel 2-Ball 40:1 13.9 l/min 650883-X4X Stainless Steel 2-Ball 43:1 3.4 l/min 67120-P4X Carbon Steel Chop Check 43:1 3.4 l/min 67121-P4X Stainless Steel Chop Check 44:1 14.3 l/min 650891-X47-B Carbon Steel Chop Check 45:1 7.2 l/min 650684-X4X Stainless Steel 2-Ball 46:1 6.4 l/min 650692-X43-B Carbon Steel Chop Check Extrusion Pump Model Reference Index 60:1 4.9 l/min 650685-X4X Stainless Steel 2-Ball 1.2:1 5.7 l/min 650841-XX4-B Carbon Steel Chop Check 3.6:1 5.7 l/min 650935-X43-C Carbon Steel Chop Check

Mount: Motor: Air Inlet: Fluid Outlet: Page #: 7 Stub 4 1 4 1/2 NPT(F) 1 NPT(F) 28 19 or 208 litre 4 1 4 1/2 NPT(F) 1 NPT(F) 29 19 or 208 litre 8 3/4 NPT(F) 1 1 2 NPT(F) 30 208 litre 10 3/4 NPT(F) 1 1 4 NPT(F) 31 Stub 4 1 4 1/2 NPT(F) 1 NPT(F) 32 19 litre 3 1/4 NPT(F) 1/2 NPT(F) 33 19 litre 3 1/4 NPT(F) 1/2 NPT(F) 34 Stub 6 1/2 NPT(F) 1 NPT(F) 35 19 or 208 litre 4 1 4 1/2 NPT(F) 1 NPT(F) 36 19 or 208 litre 6 1/2 NPT(F) 1 NPT(F) 37 208 litre 12 3/4 NPT(F) 1 1 2 NPT(F) 38 Stub 4 1 4 1/2 NPT(F) 1 NPT(F) 39 Stub 8 3/4 NPT(F) 1 NPT(F) 40 19 litre 4 1 4 1/2 NPT(F) 1/2 NPT(F) 41 19 litre 4 1 4 1/2 NPT(F) 1/2 NPT(F) 42 19 or 208 litre 8 3/4 NPT(F) 1 NPT(F) 43 Stub 6 1/2 NPT(F) 1 NPT(F) 44 19 or 208 litre 6 1/2 NPT(F) 1 NPT(F) 45 Stub 6 1/2 NPT(F) 1 NPT(F) 46 208 litre 4 in. 2 Hydraulic N/A 1 1 2 NPT (F) 47 208 litre 4 in. 2 Hydraulic N/A 1 1 2 NPT (F) 48 To use with 60 kg drums see page 11. Extrusion Pump Model Reference Index

8 Package Contents NP322L01-1 22:1 Ratio, Carbon Steel Extrusion Package NM2322E-11-P43....................Carbon Steel Pump 129121-400........................Air Filter/Regulator 651840-1..........................Carbon Steel Follower Plate 67075.............................Portable Lift Basic Pump Performance Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 44.8-244.4 bar Maximum Working Flow:.............. 3.7 l/min Displacement Per Cycle.............. 31.1 cm 3 Lower Pump Material................. Carbon Steel Plunger Material..................... 17-4 Stainless Steel Air Motor.......................... 66915 Air Motor Repair Kit.................. 637316 Lower Pump End Series.............. 67-P43 Lower Pump Repair Kit............... 637290-P43 NP322L0X-1 Portable Lift Only - Not a Ram Package Contents NP322L02-1 22:1 Ratio, Stainless Steel Extrusion Package NM2322F-11-P43....................Stainless Steel Pump 129121-400........................Air Filter/Regulator 651841-1..........................Stainless Steel Follower Plate 67075............................Portable Lift Extrusion Packages Basic Pump Performance Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 44.8-244.4 bar Maximum Working Flow.............. 3.7 l/min Displacement Per Cycle.............. 31.1 cm 3 Lower Pump Material................. 15-5 Stainless Steel Plunger Material..................... 17-4 Stainless Steel Air Motor.......................... 66915 Air Motor Repair Kit.................. 637316 Lower Pump End Series.............. 67101-P43 Lower Pump Repair Kit............... 637291-P43

Package Contents NP322R01-1 22:1 Ratio, Carbon Steel Extrusion Package NM2322E-11-P43....................Carbon Steel Pump F25241-........................Air Filter R27241-600........................Air Regulator 651840-1..........................Carbon Steel Follower Plate 651615-B..........................Single Post Ram 66713.............................Optional Portability Kit 67189.............................Optional Hold Down Kit 9 Basic Pump Performance Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 44.8-244.4 bar Maximum Working Flow:.............. 3.7 l/min Displacement Per Cycle.............. 31.1 cm 3 Lower Pump Material................. Carbon Steel Plunger Material..................... 17-4 Stainless Steel Air Motor.......................... 66915 Air Motor Repair Kit.................. 637316 Lower Pump End Series.............. 67-P43 Lower Pump Repair Kit............... 637290-P43 Package Contents NP322R0X-1 NP322R02-1 22:1 Ratio, Stainless Steel Extrusion Package NM2322F-11-P43....................Stainless Steel Pump F25241-........................Air Filter R27241-600........................Air Regulator 651841-1..........................Stainless Steel Follower Plate 651615-B..........................Single Post Ram 66713.............................Optional Portability Kit Basic Pump Performance Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 44.8-244.4 bar Maximum Working Flow:.............. 3.7 l/min Displacement Per Cycle.............. 31.1 cm 3 Lower Pump Material................. 15-5 Stainless Steel Plunger Material..................... 17-4 Stainless Steel Air Motor.......................... 66915 Air Motor Repair Kit.................. 637316 Lower Pump End Series.............. 67101-P43 Lower Pump Repair Kit............... 637291-P43 Extrusion Packages

10 Package Contents 650540-1 43:1 Ratio, Carbon Steel Extrusion Package 67120-P43.........................Carbon Steel Pump 651840-1..........................Carbon Steel Follower Plate 67075.............................Portable Lift Basic Pump Performance Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 87.7-438.7 bar Flow @ 75 Cycles/Minute:............. 3.4 l/min Displacement Per Cycle.............. 45.8 cm 3 Lower Pump Material................. Carbon Steel Plunger Material..................... 17-4 Stnls. Steel (Chrome Plated) Air Motor.......................... 65440 Air Motor Repair Kit.................. 61268 Lower Pump End Series.............. 67-P43 Lower Pump Repair Kit............... 637290-P43 65054X-1 Air Powered Lift ONLY - Not a Ram Package Contents 650541-1 43:1 Ratio, Stainless Steel Extrusion Package 67121-P43.........................Stainless Steel Pump 651841-1..........................Stainless Steel Follower Plate 67075............................Portable Lift Extrusion Packages Basic Pump Performance Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 87.7-438.7 bar Flow @ 75 Cycles/Minute:............. 3.4 l/min Displacement Per Cycle.............. 45.8 cm 3 Lower Pump Material................. 15-5 Stainless Steel Plunger Material..................... 17-4 Stnls. Steel (Chrome Plated) Air Motor.......................... 65440 Air Motor Repair Kit.................. 61268 Lower Pump End Series.............. 67101-P43 Lower Pump Repair Kit............... 637291-P43

Package Contents 650542-1 (-2 Same except Follower is 651840-2) 43:1 Ratio, Carbon Steel Extrusion Package 67120-P43.........................Carbon Steel Pump 651840-1..........................Carbon Steel Follower Plate 651615-B..........................Single Post Ram 66713.............................Optional Portability Kit Basic Pump Performance 11 Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 87.7-438.7 bar Flow @ 75 Cycles/Minute:............. 3.4 l/min Displacement Per Cycle.............. 45.8 cm 3 Lower Pump Material................. Carbon Steel Plunger Material..................... 17-4 St. Steel (Chrome Plated) Air Motor.......................... 65440 Air Motor Repair Kit.................. 61268 Lower Pump End Series.............. 67-P43 Lower Pump Repair Kit............... 637290-P43 Package Contents 650543-1 43:1 Ratio, Stainless Steel Extrusion Package 67121-P43.........................Stainless Steel Pump 651841-1..........................Stainless Steel Follower Plate 651615-B..........................Single Post Ram 66713.............................Optional Portability Kit Basic Pump Performance Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 87.7-438.7 bar Flow @ 75 Cycles/Minute:............. 3.4 l/min Displacement Per Cycle.............. 45.8 cm 3 Lower Pump Material................. 15-5 Stainless Steel Plunger Material..................... 17-4 St. Steel (Chrome Plated) Air Motor.......................... 65440 Air Motor Repair Kit.................. 61268 Lower Pump End Series.............. 67101-P43 Lower Pump Repair Kit............... 637291-P43 Package Contents NP443R01-1 43:1 Ratio, Carbon Steel Extrusion Package 67124-P43.........................Carbon Steel Pump 651613-B..........................Two-Post Mini Ram 651840-3..........................Follower Plate R27221-........................Regulator 91790.............................Muffler Basic Pump Performance Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 87.7-438.7 bar Flow @ 60 Cycles/Minute:..............2.8 l/min Displacement Per Cycle.............. 46.7 cm 3 Lower Pump Material................. Carbon Steel Plunger Material..................... 17-4 St. Steel (Chrome Plated) Air Motor.......................... 65440 Air Motor Repair Kit.................. 61268 Lower Pump End Series.............. 67-P43 Lower Pump Repair Kit............... 637290-P43 65054X-1 Shown with optional 67189 Stop & Bracket Assembly Kit NP443R01-1 Extrusion Packages This package can use 60 kg drums with a maximum height of 700mm

12 Extrusion Systems (Ordering) Series 4-1/4 Air Motor Pump Information 21 30:1 Stnls. Steel 2-Ball Pump (650485-X43) 22 22:1 Stnls. Steel 2-Ball Pump (650484-X43) 24 11:1 Stnls. Steel 2-Ball Pump (650483-X43) 31 23:1 Carbon Steel Chop Check Pump (650492-X43-B) 34 12:1 Carbon Steel Chop Check Pump (650491-X43-B) Follower Options 02 Aluminum Follower Plate with Polyurethane Double- Lipped Seal 52 Teflon Coated Aluminum Follower Plate with Polyurethane Double-Lipped Seal Popular Model Example: NP431R-02-G43 Packages include Pump, 651616-X Ram, Follower Plate Assembly, 65940 Filter/Regulator-Lubricator Kit, Air Motor Muffler & 90 Outlet Elbow. Extrusion Packages To get the desired pump ration and follower options, replace the X with appropriate numbers from the Pump Information, Follower Options and Packing Options Charts. NP4 XXR - XX - XXX Packing Options G43 R43 UHMW-PE/Leather Staggered Teflon/UHMW-PE Staggered (Upper) Teflon (Lower) NP431R-X

Extrusion Systems (Ordering) Packages include Pump, 651616-X Ram, Follower Plate Assembly, 65940 Filter-Regulator-Lubricator Kit, 91790 Air Motor Muffler & 90 Outlet Elbow. To get the desired pump ration and follower options, replace the X with appropriate numbers from the Pump Information, Follower Options and Packing Options Charts. NP6 XXR - XX - XXX 13 Series 6 Air Motor Pump Information 21 60:1 Stnls. Steel 2-Ball Pump (650685-X43) 22 45:1 Stnls. Steel 2-Ball Pump (650684-X43) 24 23:1 Stnls. Steel 2-Ball Pump (650683-X43) 31 46:1 Carbon Steel Chop Check Pump (650692-X43-B) 34 23:1 Carbon Steel Chop Check Pump (650691-X43-B) Packing Options G43 R43 Follower Options UHMW-PE/Leather Staggered Teflon/UHMW-PE Staggered (Upper) Teflon (Lower) 02 Aluminum Follower Plate with Polyurethane Double-Lipped Seal 52 Teflon Coated Aluminum Follower Plate with Polyurethane Double-Lipped Seal Popular Model Example: NP624R-02-G43 Packages include Pump, 651616-X Ram, Follower Plate Assembly, 651729 Filter-Regulator-Lubricator Kit, 92460 Air Motor Muffler & 90 Outlet Elbow. NP8 XXR - XX - XXX Series 8 Air Motor Pump Information 34 44:1 Carbon Steel Pump (650891-X47-B) G43 R43 Follower Options Packing Options UHMW-PE/Leather Staggered Teflon/UHMW-PE Staggered (Upper) Teflon (Lower) 02 Aluminum Follower Plate with Polyurethane Double-Lipped Seal 52 Teflon Coated Aluminium Follower Plate with Polyurethane Double-Lipped Seal NP834R-02-G43 Extrusion Packages

14 Model Pumps Number Description Used With Floor Mounts 65138 Floor Mount - Accepts suction line 4 1 4 & 6 air motor, 2-ball and from bulk containers or mixing tanks. extrusion pumps. Also 8 3 NPT(F) inlet. 1/4 NPT(F) 38:1 2-ball and 44:1 vent port with plug. extrusion pumps. 65139 65139 Floor Mount - Accepts suction line 8, 10 and 12 air motor 2-ball from bulk containers or mixing tanks. and extrusion pumps. Except 3 NPT(F) inlet. 1/4 NPT(F) vent 8 38:1 2-ball and 44:1 port with plug. extrusion pumps. Model Number Description Bulk/Tote Tank Supply Components A 628088-7 Material Supply Hose - Heavy duty (25mm diameter) hose features neoprene construction with a 340 bar max. working pressure capacity. Both ends 1 NPT(M). Length: 2.1 m. B 67073 Ball Valve - For use with 628088-7 material supply hose. 306 bar max. working pressure rated. B C A D C 628089-X Material Hose With Fittings - 76mm diameter hose has cross-linked polyethylene (internal) and neoprene (external) construction. Hose comes with female cam-lever locking coupler, male adapter, cam-lever locking dust cap and dust plug. Length: 0.6 m (628089-2), 1.2m (628089-4) & 1.8m (628089-6). Maximum working pressure: 125 psi D 65138, Pump Floor Mount - See above for floor mount information. 65139 Model Used Follower Plate Number Description With Used With Rams for 19 or 60 litre Drums 651613-B Two Post Ram N Series 22:1 & 651840-1 (19 or 60 litre drums) 4 1 4 air motor pumps 66731-1 Extrusion Accessories 651613-B 651615-B Single Post Ram - For use with N Series 651840-X, materials up to 1,000,000 CPS viscosity. 22:1 pumps or Follower For 19 litre containers. Hold-down & 4 1 4 air motor Plates clamps secure pail. 66713 Portability Kit 43:1 extrusion available for mobile applications. pump 66713 Portability Kit - Mounts directly to 651615-B the base of the 651615-B Ram, to Single Post allow ease of portability. Will clear Rams and 711 mm openings. Has Ram packages 305 mm tyres. 67189 Stop & Bracket Kit Assembly - To secure pail to ram base. NOTE: Order mounting plate 91395 separately to mount a NM2304B-11-XXX on the 651615 ram. 651615-B

Model Used Follower Plate Number Description With Used With 15 Rams for 19 or 208 litre drums 651616-1 Two Post Ram - For use with materials 4 1 4 & 6 66516 Follower over 200,000 CPS viscosity. Consists of air motor Plate. two 3-1/2 diameter air cylinders joined by Integrity pumps. For 19 litre cross-over tubes and welded to a steel Also 8 air motor containers use base. Cast aluminum follower plate has 44:1 extrusion 66469 double edge Buna N wiper to clean drum pumps & 40:1 Follower Plate. and seal material from atmosphere. Integrity Base is 991 mm x 610 mm. pumps. Raised height is 2.5 m Lowered position is 1.6 m. 651616-51 Two Post Ram - Same as 651616-1, Same as above 66516-5 except follower plate has Telfon coating. 651616-2 Two Post Ram - Same as 651616-1 Same as above 66516-1 except for polyurethane wiper. 651616-52 Two Post Ram - Same as 651616-2, Same as above 66516-6 except follower plate has Telfon coating. 651616-3 Two Post Ram - Same as 651616-1 Same as above 66516-2 except for EPR wiper. 651616-53 Two Post Ram - Same as 651616-3, Same as above 66516-7 except follower plate has Telfon coating. 651616-4 Two Post Ram - Same as 651616-1 8, 10, 12 66517 except for the mounting for larger pumps air motor extrusion and Follower Plate. pump. Except 8 44:1 extrusion pump & 40:1 Integrity pumps. 651616-54 Two Post Ram - Same as 651616-4, Same as above 66517-5 except follower plate has Telfon coating. 651616-5 Two Post Ram - Same as 651616-4, Same as above 66517-1 except for polyurethane wiper. 651616-55 Two Post Ram - Same as 651616-5, Same as above 66517-6 except follower plate has Telfon coating. 651616-6 Two Post Ram - Same as 651616-4 Same as above 66517-2 except for EPR wiper. 651616-56 Two Post Ram - Same as 651616-6, Same as above 66517-7 except follower plate has Telfon coating. 651616-13 Two Post Ram - Same as 651616-1 4 1 2 & 6 air motor 67195-2 except follower plate has two EPR 2-ball & extrusion tube type wiper seals. pumps. Also 8 air motor 44:1 extrusion pumps & 40:1 Integrity pumps. 651616-57 Two Post Ram - Same as 651616-13, Same as above 67195-6 except follower plate has Telfon coating. 651616-14 Two Post Ram - Same as 651616-13, Same as above 67195-1 except for Neoprene wiper seals 651616-58 Two Post Ram - Same as 651616-14, Same as above 67195-5 except plate has Telfon coating. 651616-15 Two Post Ram - Same as 651616-13, Same as above 67195-3 except for Viton wiper seals. 651616-X Extrusion Accessories

16 Model Used Follower Plate Number Description With Used With 651616-X 66354-1 651616-59 Two Post Ram - Same as 651616-15, 4 1 2 & 6 air motor 67195-7 except follower plate has Teflon coating. Integrity pumps pumps. Also 8 air motor 44:1 extrusion pumps & 40:1 Integrity pumps 651616-16 Two Post Ram - Same as 651616-4 8, 10 & 12 air 67196-2 except follower plate has two EPR motor extrusion pumps. tube type wiper seals. Except 8 44:1 extrusion & 40:1 Integrity pumps 651616-60 Two Post Ram - Same as 651616-16, Same as above 67196-6 except follower plate has Telfon coating. 651616-17 Two Post Ram - Same as 651616-16, Same as above 67196-1 except for Neoprene wiper seals. 651616-61 Two Post Ram - Same as 651616-17, Same as above 67196-5 except plate has Telfon coating. 651616-18 Two Post Ram - Same as 651616-16, Same as above 67196-3 except for Viton wiper seals. 651616-62 Two Post Ram - Same as 651616-18, Same as above 67196-7 except plate has Telfon coating. 66353-1 Pump Stabilising Brackets - Attaches 8, 10, 12 easily to 651616 Ram. Kit includes hardware. Air Motor Pumps 66354-1 Pump Stabilising Brackets - Same as 4 1 4 & 6 66353-1 except fits smaller pumps. Air Motor Pumps 67133 Drum Hold-Down Brackets - Kit includes 2 brackets, clamp screws, nuts. 67133 Extrusion Accessories Rams (Continued) Pump/Drum Stabilising Brackets

Model Follower Pumps Number Model No. Material Used With 17 Extra Heavy-Duty Rams 208 litre Containers The 651612-X extra heavy-duty ram features 139mm diameter post construction capable of delivering 0-0.75 bar* follower down force. This extra measure of down force makes the 651612 Ram the best choice for the hard-duty supply of heavy inks, RTV silicones, caulkings, varnishes, highly viscous adhesives and much more. 651612-1 66516 Buna N 4 1 4, 6 air motor Chop Check and Two-Ball pumps. 8 air motor 44:1 Chop Check and 40:1 Integrity pumps. 651612-2 66516-1 Polyurethane same as 651612-1 651612-4 66517 Buna N 8,10 and 12 air motor Chop Check and Two-Ball pumps, except 8 air motor 44:1 and 40:1 Integrity pumps. 651612-5 66517-1 Polyurethane same as 651612-4 651612-6 66517-2 EPR same as 651612-4 * WARNING: Before using maximum follower down force, check container or consult container manufacturer for maximum pressure rating. The 651614 Ram / Lift provides responsive pump lifting and pump lowering with sufficient downforce to permit pump extrusion of materials up to 500,000 c.p.s. Its ability to revolve 360-degrees allows the ongoing placement and rotation of three, 208 litre containers a critical feature in applications that demand continuous material supply. 651612-X Model Fits Height Height Air Number ARO Pump Raised Lowered Inlet Single Post Rams 651614-1 4-1/4-6 Air Motors 2.8 m 1.6 m 1/4 NPT 651614-2 8 to 12 Air Motors 2.8 m 1.6 m 1/4 NPT 651614-3 Small Hydraulic Motor 2.8 m 1.6 m 1/4 NPT 651614-4 Large Hydraulic Motor 2.8 m 1.6 m 1/4 NPT The above models include the brackets and hardware needed to accommodate two-ball or extrusion tie-rod style pumps. 651614-1 (Pump sold separate) 651614-2 (Pump, Follower, and Follower Assist Kit sold separate) Extrusion Accessories

18 Model Ram or Lift Follower Plate Number Description Used With Used With Follower Plates 19 litre Containers 66469 Follower Plate - Carbon 651614-1, 651616-X 4 1 4 &6 steel with Buna N wiper. & 651615-B Rams Integrity* or 640169 Lift pumps. 66731 Follower Plate - Electroless 651615-B NM2322X-11-X, nickel-plated with double-edge Rams 4 1 4 air motor Buna N wiper and seal. 9:1 & 46:1 pumps. 66469 66731-1 Follower Plate - Electroless 651614-1, 651616 NM2304B-11-X, nickel-plated with double-edge & 651615-B 4 1 4 air motor polyurethane wiper and seal. Rams 9:1 & 46:1 pumps. 66731-2 Follower Plate - Electroless 651614-1, NM2322X-11-X, nickel-plated with double-edge 651615-B 4 1 4 air motor EPR wiper and seal. Rams 9:1 & 46:1 pumps. 66732 Follower Plate - Electroless 651614-1, 4 1 4 & 6 air nickel-plated with double-edge 651615-B motor Integrity Buna N wiper and seal. Rams pumps. Also 8 air motor 44:1 extrusion pumps & 40:1 Integrity* pumps. 66732-1 66732-1 Follower Plate - Electroless 651614-1, 4 1 4 & 6 air motor nickel-plated with double-edge 651615-B Integrity pumps. polyurethane wiper and seal. Rams Also 8 air motor 44:1 extrusion & 40:1 Integrity* pumps. 66732-2 Follower Plate - Electroless 651614-1, 4 1 4 & 6 air motor nickel-plated with double-edge 651615-B Integrity pumps. EPR wiper and seal. Rams Also 8 air motor 44:1 extrusion & 40:1 Integrity* pumps. Extrusion Accessories 651842-1 67136 651840-1 Follower Plate - Carbon steel 651615-B NM2322X-11-X. with 290-mm polyethylene - Rams Replaces urethane wiper seal 651810. 651840-2 Follower Plate - Carbon Steel 651615-B NM2322X-11-X. with 295-mm nitrile seal. Rams Replaces Designed for metric pails 651810. 651840-3 Follower Plate - Carbon Steel, 651615-B NM2322X-11-X. with 311.9-mm polyethylene - Rams Replaces urethane wiper seal. Designed 651810. for metric pails. 651841-1 Follower Plate - Stainless Steel 651615-B NM2304B-11-X with 290-mm polyethylene - Rams & 4 1 4 air motor urethane wiper seal. 43:1 pumps 651842-1 Follower Plate - Stainless Steel 651615-B Integrity with 290-mm polyethylene - Rams pumps urethane wiper seal. (No adapter required) * Requires 67136 Follower Plate Adapter. Accessories 91364-10 Seal Protectors - Package of 10 for 19 litre followers 19 litre to be inserted between the follower plate and the material Follower Plates in the container. This helps to prevent corrosive materials from attacking the wiper and reduces clean-up time. 67136 Follower Plate Adapter - For attaching Integrity 66248 & 66516 to follower plates or floor stand. Includes stainless Followers. steel adapter w/2 NPT(F) threads, seal and hardware. 651616-1,-2,-3 Rams. 65138 Floor Mounts

Model Rams Pumps Number Description Used With Used With 19 Follower Plates 208 litre Containers 66248 Follower Plate - Single lip 651614-X Ram 4 1 4 & 6 air Buna N wiper with polyethylene 640169 Lift motor 2-ball & back-up. extrusion pumps 66248-1 Follower Plate - Same as 66248, Same as above Same as above except with polyethylene wiper. 66516 Follower Plate - Cast Aluminum 651614-X, 4 1 4 & 6 air with double-edged 651616-X motor 2-ball & Buna N wiper & seal. extrusion pumps Also 8 air motor 40:1 Integrity & 44:1 extrusion pumps 66516-5 Follower Plate - Same as Same as above Same as above 66516, except follower plate has Teflon coating. 66516-1 Follower Plate - Same as Same as above Same as above 66516, except with polyurethane wiper & seal. 66516-6 Follower Plate - Same as Same as above Same as above 66516-1, except follower plate has Teflon coating. 66516-2 Follower Plate - Same as Same as above Same as above 66516, except with EPR wiper & seal. 66516-7 Follower Plate - Same as, Same as above Same as above 66516-2 except follower plate has Teflon coating. 66517 Follower Plate - Cast 651614-X, 8, 10 & 12 air Aluminum with double- 651616-X motor extrusion edge Buna N wiper and seal. pumps. Except 8 40:1 Integrity & 44:1 extrusion pumps. 66517-5 Follower Plate - Same as Same as above Same as above 66517, except follower plate has Teflon coating. 66517-1 Follower Plate - Same as Same as above Same as above 66517, except with polyurethane wiper & seal. 66517-6 Follower Plate - Same as Same as above Same as above 66517-1, except follower plate has Teflon coating. 66517-2 Follower Plate - Same as Same as above Same as above 66517, except with EPR wiper & seal. 66517-7 Follower Plate - Same as Same as above Same as above 66517-2, except follower plate has Teflon coating. 67195-2 Follower Plate - Cast Aluminum 651614-X, 4 1 4 & 6 air motor with two EPR tube type wiper 651616-X 2-ball & extrusion seals. pumps. Also 8 40:1 Integrity & 44:1 extrusion pumps. 67195-6 Follower Plate - Same as Same as above Same as above 67195-2, except follower plate has Teflon coating. 66248 66516 67195-X Extrusion Accessories

20 Model Rams Pumps Number Description Used With Used With 6719X-X Follower Plates 208 litre Containers 67195-1 Follower Plate - Same as 651614-X, 4 1 4 & 6 air motor 67195-2, except with Neoprene 651616-X 2-ball & extrusion wiper seals. pumps. Also 8 40:1 Integrity & 44:1 extrusion pumps. 67195-5 Follower Plate - Same as Same as Same as 67195-1, except follower plate previous previous has Teflon coating. 67195-3 Follower Plate - Same as Same as Same as 67195-1, except with Viton wiper seals. previous previous Extrusion Accessories 67136 67195-7 Follower Plate - Same as Same as Same as 67195-3, except follower plate previous previous has Teflon coating. 67196-2 Follower Plate - Cast Aluminum 651614-X, 8, 10 & 12 air with two EPR tube type wiper 651616-X motor extrusion seals. pumps. Except 8 40:1 Integrity & 44:1 extrusion pumps 67196-6 Follower Plate - Same as Same as above Same as above 67196-2, except follower plate has Teflon coating. 67196-1 Follower Plate - Same as Same as above Same as above 67196-2, except with EPR wiper seals. 67196-5 Follower Plate - Same as, Same as above Same as above 67196-1 except follower plate has Teflon coating. 67196-3 Follower Plate - Same as Same as above Same as above 67196-2, except with Viton wiper seals. 67196-7 Follower Plate - Same as Same as above Same as above 67196-3, except follower plate has Teflon coating. Seal Protectors 91363-10 Seal Protectors - Package of 10 for 208 litre followers 208 litre to be inserted between the follower plate and the material Follower in the container. This helps to prevent corrosive materials Plates from attacking the wiper and reduces clean-up time. Model Ram Number Description Used With Pump Follower/Floor Stand Adapters 67134 Follower Plate Adapter - 66516-X & 6719X-X Followers For attaching NM2322X-X & 651616-1, -2, -3, 651614-X 6712X-P43 pumps to 55-gal. and 651612-X Rams. follower plates or floor stands 65138 Floor Mount 67136 Follower Plate Adapter - 66248 & 66516 For attaching Integrity pumps Followers. to follower plates or floor stand. 651616-1, -2, -3 Rams Includes stainless steel adapter w/2 65138 Floor Mount NPT(F) threads, seal and hardware.

Regulated Working Maximum Gauge Base Pressure Pressure Inlet Pressure Model Housing Seat Range W/Gauge Pressure Range Number (See code at bottom) bar bar bar bar 21 Downstream Fluid Regulators 3/8 ports, standard flow to 11.4 litres Gauge Included. 651780-A1A-B C/S T/C 28-86 207 651780-A1B-B C/S T/C 69-207 414 651780-A3A-B S/S T/C 28-86 207 651780-A3B-B S/S T/C 69-207 414 3/8 ports, high-flow to 22.7 litres 651790-B1D-B Z/A T/C 2-14 41.4 86 0-20 651790-B1E-B Z/A T/C 7-55 86.2 86 0-69 651790-B3D-B S/S T/C 2-14 41.4 86 0-20 651790-B3E-B S/S T/C 7-55 86.2 86 0-69 Gauge Included. 651780-B1A-B C/S T/C 28-86 207 651780-B1B-B C/S T/C 69-207 414 651780-B3A-B S/S T/C 28-86 207 651780-B3B-B S/S T/C 69-207 414 3/8 Ports Model 3/4 ports, mastic-flow to 75.7 litres** 651780-C1C-B C/S T/C 138-345 414 651780-C3B-B S/S T/C 52-172 414 3/8 ports, remote models, flow to 22.7 litres *651790-B4R-B S/S 3/S 2-14 34 651780-B1R-B C/S T/C 14-345 414-651780-B3R-B S/S T/C 14-345 414 - Gauge NOT Included. ** Flow rates tested in 30 wt. oil. 3/4 Ports Model 3/4 ports, remote models, mastic-flow to 75.7 litres** 651780-C1R-B C/S T/C 52-345 414 651780-C3R-B S/S T/C 52-345 414 ** Flow rates tested in 55 CPS material. Code Description Code Description High Pressure Remote Model Material Codes 3/S 300 Series Stainless Steel T/C Tungsten Carbide 4/S 400 Series Stainless Steel S/S Stainless Steel C/S Carbon Steel Z/A Zinc Aluminum Z Zinc Code Description Material Fluid Regulator Gauges / Adapters 93506-1 Gauge, 0-204 bar Stainless Steel 93505-1 Gauge, 0-204 bar Non-Stainless Steel 93507-1 Gauge, 0-340 bar Non-Stainless Steel 92968 Adapter, 3/8 Dual Outlet Ports 92969 Adapter, 3/4 Single Outlet Ports Extrusion Accessories

22 Max. Fluid Fluid Fluid Outlet Working Model Pressure Inlet I.D. & Thread Pressure Number Description Bar in mm Bar Extrusion Accessories 651513 66541-XX 651412-X 651420-XX-B 651511 651418-XX-B Automatic Extrusion Guns 651511 Flow Gun - Requires 345 3/8 6 & (2) 3.4 at 4-way air valve to open NPT 11/16-16 1/8 F 138 bar and close. Adjusting (F) (2) (M) fluid screw varies stroke length. pressure Secures to 1/2 diameter rod by allen screw. Aluminum body with tungsten carbide seats. Order 66541-XX Extrusion Nozzle Kit separately. 651513-11-B Flow Gun - Has air 345 1/4 2.3 & 1/8 3.4 at open, spring return NPS 11/16-16 (F) 138 bar cylinder. Requires (M) (M) fluid 3-way air valve to open. pressure Adjusting screw varies stroke length. Secures to 1/2 diameter rod by allen screw. 316 stainless steel with tungsten carbide seat. Order 66541-XX Extrusion Nozzle Kit separately. 651536-1 Snuff-Back Gun - High 345 3/8 1/4 (2) flow automatic dispensing NPT NPT 1/8 gun is designed to handle (F) (F) NPT (F) high-viscosity materials. (2) Requires a 4-way air valve to open and close. 651537-1 Flow Gun - Similar to 345 3/8 3/8 (2) 3.4 at 651511 except with carbon NPT 18 (M) 1/8 138 bar steel body and has ball (F) NPT (F) fluid seat located at material inlet pressure of valve seat assembly. Model Orifice Model Orifice Model Orifice Number Diameter Nimber Diameter Number Diameter Extrusion Gun Nozzle Kits 66541-XX Extrusion Nozzle Kit - Used on manual or automatic extrusion guns. Hardened steel assembly includes nozzle and cap. 11/16-16 UN(F). 66541-3.031 66541-9.093 66541-17.172 66541-4.046 66541-12.125 66541-18.187 66541-6.063 66541-15.156 66541-25.250 66541-37.375 Maximum Fluid Filter Filter Model Pressure Filter Inlet(s) Size Outlet(s) Size Number Bar Mesh Microns (Qty) NPT (Qty) NPT Material Filters-Standard Models 1/4 fluid inlet/carbon steel construction 651412 345 70 200 1/4-F (2) 1/4-F (3) Bottom swivel 651412-6 345 70 200 1/4-F (2) 1/4-F (3) Side swivel 651412-8 345 149 1/4-F (2) 1/4-F (3) 1/2 fluid inlet/stainless steel construction (passivated) 651422-40 414 40 375 1/2-F (2) 1/2-F (1) 651422-70 414 70 200 1/2-F (2) 1/2-F (1) 651422-414 149 1/2-F (2) 1/2-F (1) 1/2 fluid inlet/carbon steel construction (e-nickel plated)) 651420-40 414 40 375 1/2-F (2) 1/2-F (1) 651420-70 414 70 200 1/2-F (2) 1/2-F (1) 651420-414 149 1/2-F (2) 1/2-F (1) 651421-70 414 Dual Screens 1-8 3/4-F (1) 1 fluid inlet/carbon steel construction (e-nickel plated)) 651418-40-B 414 40 375 1-F (2) 3/8-F (3) 651418-70-B 414 70 200 1-F (2) 3/8-F (3) 651418--B 414 149 1-F (2) 3/8-F (3)

Max Fluid Fluid Fluid Outlet Model Pressure Inlet I.D. & Thread Number Description bar In. mm 23 Manual Extrusion Guns *651500 Flow Gun - Aluminum body with 517 3/8 (F) 6 & tungsten carbide seats. Used to 11/16-16 (M) extrude material over 200,000 CPS. Order 66541-XX Extrusion Nozzle Kit separately. 651533 Flow Gun - Wetted parts of 316 345 1/4 2.3 & series stainless steel with tungsten NPS(M) 11/16-16 (M) carbide seats. Used to extrude material up to 200,000 CPS. Order 66541-XX Extrusion Nozzle Kit separately. 641523-1 Flow Gun - Wetted parts of 300 207 3/8 (F) 6 & Series stainless steel with Teflon 1/4 NPT(F) packings. Used to extrude material over 200,000 CPS. Order 76751 Adapter and 66541-XX Extrusion Nozzle Kit separately. *WARNING: Do not use with halogenated hydrocarbons. This model contains aluminum parts that come in contact with the material being dispensed. Aluminum is not compatible with halogenated hydrocarbon solvents. 651533 651500 Extrusion Gun Nozzle Kits 76751 Adapter - 1/4NPT(M) to 11/16-16(M) adapts 66541-XX Extrusion Nozzle Kit to fluid outlet for 641523 Flow Guns. 66541-XX Extrusion Nozzle Kit - Used on manual or automatic extrusion guns. Hardened steel assembly includes nozzle and cap. 11/16-16 UN(F). For orifice diameter, see chart on previous page. Model Thread Size Type Max. Working Number In. NPT x NPT of Seals Pressure bar 641523-1 (Shown with 66541-XX) 66541-XX Swivels Swivels are used to give mobility and flexibility for material hoses and dispensing guns. Select the proper working pressure and check the compatibility of the seals with the material being pumped. straight 636075 1/8 (M) x 1/8 (F) Fabric with Neoprene 552 2085 1/8 (M) x 1/8 (F) Fabric with Neoprene 552 636085 3/8 (M) x 3/8 (F) Fabric with Neoprene 552 635117 1/2 (M) x 1/2 (F) Fabric with Neoprene 552 635108 3/4 (M) x 3/4 (F) Fabric with Neoprene 69 Z 636077 1/8 (M) x 1/8 (F) Fabric with Neoprene 552 636080 1/8 (M) x 1/4 (F) Fabric with Neoprene 552 636088 3/8 (M) x 3/8 (F) Fabric with Neoprene 552 635106 1/2 (F) x 3/8 (M) Fabric with Neoprene 552 636087-B* 1/4-18 NPT (F) x 1/4-18 NPT (M) Fabric with Neoprene 345 636086-B 1/4-18 NPT (F) x 1/4-18 NPT (M) Fabric with Neoprene 345 * Includes internally mounted element 636075 636075 Extrusion Accessories

24 Pumps Port Reg. Pressure Max. Model Used Size Range Flow Number Description With NPT bar Pressure Air Filter/Regulator/Lubricator MINIATURE F/R/L 128121-800 Filter/Regulator/Lubricator 2 & 3, 1/4 (F) 0.3-8.6 6 dm 3 /s Drop/fog-type lubrication, air motor 20 micron filter, pumps polycarbonate bowls. 128121-800 129121-400 C28241-810 129121-400 Filter/Regulator 2 & N, 1/4 (F) 0.3-8.5 6 dm 3 /s Drop/fog-type lubrication, air motor 20 micron filter, pumps polycarbonate bowls. MODULE/AIR 2000 F/R/L C28241-810 Filter/Regulator/Lubricator 4 1 4 & 1/2 (F) 0.3-8.6 52 dm 3 /s Drop/fog-type lubrication, 6 air 40 micron filter, motor metal bowls w/ sight glass. pumps P29241-610 Filter/Regulator 4 1 4 & 6 1/2 (F) 0.3-8.5 66 dm 3 /s Drop/fog-type lubrication, air motor 40 micron filter, pumps metal bowls w/ sight glass. HEAVY DUTY F/R/L 28353 Filter/Regulator/Lubricator 8, 10 3/4 (F) 0.3-8.6 35 dm 3 /s Drop/fog-type lubrication, & 12 40 micron filter, air motor polycarbonate bowls. pumps F/R/L Assemblies 651729 Kit Assembly 8, 10, 3/4 (M) 0.3-8.6 35 dm 3 /s Heavy-Duty FRL w/ hose & 12 & mounting bracket for air motor installation to Two Post pumps Ram. 65940 Kit Assembly 4 1 4 & 1/2 (M) 0.3-13.8 31 dm 3 /s Heavy-Duty FRL w/ hose 6 air & mounting bracket for motor installation to Two Post pumps Ram. Extrusion Accessories C28241-810 28353 Air Line Lubricant 62274 One Quart Bottle - A high quality EP extreme pressure gear oil, nondetergent, rust or oxidation inhibited, with a viscosity of 700-0 S.U.S. at F.

Pumps Air Air Pressure Model Used Inlet Outlet Range Number Description With NPT NPT bar 25 Over-run Controls 635040 ARO-STOP Valve N Series, 1/4 (F) 1/4 (M) 1.4-12 Shuts off air to the pump air motor when material container is pumps empty or line is broken. only Quick set and reset feature. 23644-400 ARO-STOP Valve 4 1 4 & 1/2 (F) 1/2 (M) 1.4-12 Shuts off air to the pump 6 air when material container is motor empty or line is broken. pumps Quick set and reset feature. 635043 ARO-STOP Valve 8", 10 3/4 (F) 3/4 (M) 1.4-12 Shuts off air to the pump & 12 when material container is air motor empty or line is broken. pumps Quick set and reset feature. only 635040 Pump Air Size Model Used Inlet Number Description With NPT mm x mm Air Motor Muffler 91790 Air Motor Muffler 4 1 4 & 6 1-1/4 (M) 89 x 284 Reduces air exhaust noise level air motor to acceptable OSHA standards. pumps 92460 Air Motor Muffler 8 air motor, 1-1/4 (M) 143 x 391 Reduces air exhaust noise level pumps to acceptable OSHA standards. 66718 Air Motor Muffler 10 & 12 Bolted-on 229 x 508 Reduces air exhaust noise level air motor, to acceptable OSHA standards. pumps 91790 92460 Model Used Number Description With Wet Sol Plus 66333-B Wet Sol - One litre Container All pumps with wet cups. Designed to prolong packing life by keeping the piston rod and packings wetted. Also reduces the possibility of material hardening on the piston rod. 66334-B Wet Sol - 3.8 litre Container 66718 66334-B Extrusion Accessories

26 Five Simple Steps to the Right ARO Pump. 1 Pump Style This identifies the type of pump. You can also identify the pump s ratio and the maximum fluid pressure the pump can produce. 2 Pump Performance Here you can locate information on the performance of each pump model. This includes air inlet and fluid pressure ranges, maximum recommended cycles and displacement per cycle. Also, use this area to locate data on flow and noise levels. A photo of each model provides dimensional data. 3 Pump Motor/Lower Specifications Important specifications for each pump are conveniently located in one area. Service kits for the air motor and lower end are listed. This section also contains data needed to spec a pump into a specific system, if necessary. 4 Pump Packings - Ordering Pump Style Ratio:? PSI:?? (Max.) Type:? 5 ARO offers several types of lower end packings in an effort to meet the performance demands of different applications. Not all packing types are available on each pump. Use this section to select the appropriate packing set-up for your application. The ordering menu easily identifies which packings can be chosen. Recommended Accessories ARO offers many accessories that can improve the performance of the pump you ve selected. Several of these accessories are listed along with each pump. There is also a complete listing of accessories at the end of each section. That way the accessories most often needed for an application are easily accessible.

Performance 27 Air Inlet Pressure Range.............. Fluid Pressure Range................ Max. Rec d Cycles Per Minute.......... Displacement Per Cycle.............. Cycles Per Gallon................... Flow @ Cycles / Minute........... 2 Noise Level @ Psi............... Specifications Lower Pump Material................. Plunger Material..................... Cylinder Material.................... Air Motor.......................... Motor Repair Kit.................... Motor Diameter.................... Stroke............................ Air Inlet........................... Lower Pump End Series.............. Lower Pump Repair Kit............... Material Inlet....................... Material Outlet...................... Weight............................ 3 NM2322E-11-P4X Ordering Recommended Accessories N M 2 3 2 2 E - 1 1 - P 4 X Packing / Plunger 3 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE Grooved Piston (Lower) 8 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE Single Lip Cup (Lower) Air F/R/L: 128121-800 Airline Oil: 62274 Wet Sol: 66333-B Follower Plate: Page 18 A.S.A.P. Packages: NM322R01-1 NP322L01-1 1 4 5 Pump Style Ratio:? Bar:?? (Max.) Type:?

28 650483-X4X Performance 4-1/4", 11:1, 2-Ball Air Inlet Pressure Range.............. 2-10.2 bar 4-1/4" (11:1) 9 mm Fluid Pressure Range................ 22.4-112.2 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 237.6 cm 3 Cycles Per Litre..................... 4.2 Flow @ 60 Cycles / Minute............ 13.9 l/min Noise Level @ 4 bar.................. 81.8 db(a) Specifications Lower Pump Material................. CF-8M Stnls. Steel Plunger Material..................... See Plunger Options Below Cylinder Material.................... See Plunger Options Below Air Motor.......................... 65465-B Motor Repair Kit.................... 61268 Motor Diameter.................... 10.8 cm (4-1/4 ) Stroke............................ 152 mm 481 mm 322 mm Air Inlet........................... 1/2 NPT(F) Lower Pump End Series.............. 66300-X4X Lower Pump Repair Kit.............. 637305-X4X Material Inlet....................... 1 NPT(F) / 2 NPT(M) Material Outlet...................... 1 NPTF-1(F) Weight............................ 19.5 kg Recommended Accessories Air F/R/L: C28241-810 Airline Oil: 62274 Air Motor Muffler: 91790 Wet Sol: 66333-B Wall Mount: 66 Floor/Follower Adapter: 67136 Floor Mount: 65138 Ordering 6 5 0 4 8 3 - X 4 X Packings Plungers 3 : Teflon 3 : 17-4 Stnls. Steel, C : UHMW-PE Hard Chrome Plated G : UHMW-PE/Leather B : 17-4 Stnls. Steel, P : UHMW-PE/Leather (Upper), Ultra Coated UHMW-PE (Lower) R : Teflon/UHMW-PE (Upper), Teflon (Lower) COATING Piston Pumps Ratio: 11:1 Bar: 112.2 (Max.) Type: 2-Ball Fluid Pressure (Bar) CYCLES PER MINUTE 0 20 40 60 80 120 50 90 Performance based on 5 poise oil at ambient temperature 8.3 bar 45 80 8.3 bar 40 70 60 50 40 30 20 10 35 30 25 20 15 10 5 Air Consumption (litres/sec.) 0 0 0 5 10 15 20 25 LITRES PER MINUTE DELIVERY

Fluid Pressure (Bar) Performance 4-1/4", 12:1, Chop Check Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 24.4-122.4 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 206.4 cm 3 Cycles Per Litre..................... 4.8 Flow @ 60 Cycles / Minute............ 12.4 l/min Noise Level @ 4 bar.................. 80 db(a) w/muffler Specifications Lower Pump Material................. Carbon Steel (Nickel Plated) Plunger Material..................... 17.4 Stnls. Steel (Hard Chrome Plated) Cylinder Material.................... Carbon Steel (Nickel Plated) Air Motor.......................... 65465-B Motor Repair Kit.................... 61268 Motor Diameter.................... 4-1/4 Stroke............................ 152 mm Air Inlet........................... 1/2 NPT(F) Exhaust Port...................... 1-1/4 NPT(F) Chop Check Pump Model............. 66243-X43-B Lower Pump Repair Kit.............. 637071-X43-B Material Inlet....................... Flange Mount Material Outlet...................... 1 NPT(F) Weight............................ 29 kg Ordering 6 5 0 4 9 1 - X 4 3 - B Packings G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-(Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) CYCLES PER MINUTE 0 50 150 200 250 300 120 120 Performance based on 90 wt. gear oil at ambient temperature 8.3 bar 80 80 60 60 40 40 20 20 0 0 0 10 20 30 40 50 LITRES PER MINUTE DELIVERY 8.3 bar Air Consumption (litres/sec.) 1311.9 mm 650491-X43-B 780.6 mm 450.4 mm Recommended Accessories Air F/R/L: C28241-810 Airline Oil: 62274 Air Motor Muffler: 91790 Wet Sol: 66333-B Floor Mount: 65138 Rams: Page 15 Ratio: 12:1 Bar: 122.4 (Max.) Type: Chop Check 29 4-1/4" (12:1) CS Extrusion Pumps

30 8" (13:1) CS Extrusion Pumps Ratio: 13:1 Bar: 106.1 (Max.) Type: Chop Check 650871-XX4-B 1329.5 mm 508 mm Recommended Accessories Air F/R/L: 28353 Airline Oil: 62274 Air Motor Muffler: 92460 Wet Sol: 66333-B Floor Mount: 65139 Ram: Page 15 797.7 mm Fluid Pressure (Bar) Performance 8", 13:1, Chop Check Air Inlet Pressure Range.............. 2-8.1 bar Fluid Pressure Range................ 26.5-106.1 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 662 cm 3 Cycles Per Litre..................... 1.5 Flow @ 60 Cycles / Minute............ 39.6 lpm Noise Level @ 4 bar.................. 80 db(a) w/muffler Specifications Lower Pump Material................. Carbon Steel (Nickel Plated) Plunger Material..................... Carbon Steel (Chrome Plated) Cylinder Material.................... Carbon Steel (Nickel Plated) Air Motor.......................... 66523 Motor Repair Kit.................... 66614 Motor Diameter.................... 8 Stroke............................ 152 mm Air Inlet........................... 3/4 NPT(F) Exhaust Port...................... 1-1/4 NPT(F) Chop Check Pump Model............. 66236-XX4-B Lower Pump Repair Kit.............. 637128-XX4-B Material Inlet....................... Flange Mount Material Outlet...................... 1-1/2 NPT(F) Weight............................ 57 kg Ordering 6 5 0 8 7 1 - X X 4 - B Packings / Springs F4 : UHMW-PE/Leather Staggered (Upper), UHMW-PE (Lower), Multiple Wave Spring J3 : Polyurethane (Upper), UHMW-PE (Lower), No Spring P4 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower), Multiple Wave Spring R4 : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Multiple Wave Spring CYCLES PER MINUTE 0 20 40 60 80 120 120 8.3 bar Performance based on 90 wt. gear oil at ambient temperature 8.3 bar 80 80 60 60 40 40 20 20 0 0 0 10 20 30 40 50 LITRES PER MINUTE DELIVERY Air Consumption (litres/sec.)

Fluid Pressure (Bar) 0 180 160 140 Performance 10", 20:1, Chop Check Air Inlet Pressure Range.............. 6.1 bar Max. Fluid Pressure Range................ 122.4 bar Max. Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 662 cm 3 Cycles Per Litre..................... 1.5 Flow @ 60 Cycles / Minute............ 39.6 l/min Noise Level @ 4 bar.................. 82 db(a) w/muffler Specifications Lower Pump Material................. Carbon Steel (Nickel Plated) Plunger Material..................... Carbon Steel (Chrome Plated) Cylinder Material.................... Carbon Steel (Nickel Plated) Air Motor.......................... 66651 Motor Repair Kit.................... 637110 Motor Diameter.................... 10 Stroke............................ 152mm Air Inlet........................... 3/4 NPT(F) Exhaust Port...................... 1-1/4 NPT(F) Chop Check Pump Model............. 66236-XX4-B Lower Pump Repair Kit.............. 637128-XX4-B Material Inlet....................... Bolted Flange Material Outlet...................... 1-1/2 NPT(F) Weight............................ 65.4 kg Ordering 20 CYCLES PER MINUTE 40 60 80 120 180 120 120 80 60 40 6 5 0 8 7 5 - X X 4 - B Packings / Springs F4 : UHMW-PE/Leather Staggered (Upper), UHMW-PE (Lower), Multiple Wave Spring J3 : Polyurethane (Upper), UHMW-PE (Lower), No Spring P4 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower), Multiple Wave Spring R4 : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Multiple Wave Spring Performance based on 90 wt. gear oil at ambient temperature 20 20 0 0 0 10 20 30 40 50 60 70 LITRES PER MINUTE DELIVERY 160 140 80 60 40 Air Consumption (litres/sec.) 1301.7 mm 650875-XX4-B 508 mm Recommended Accessories Air F/R/L: 28353 Airline Oil: 62274 Air Motor Muffler: 66718 Wet Sol: 66333-B Floor Mount: 65139 Rams: Page 15 797.7 mm Ratio: 20:1 Bar: 122.4 (Max.) Type: Chop Check 31 10" (20:1) CS Extrusion Pumps

32 4-1/4" (22:1) CS 9 mm 650484-X4X 481 mm 322 mm Performance 4-1/4", 22:1, 2-Ball Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 44.8-224.4 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 122.9 cm 3 Cycles Per Litre..................... 8.1 Flow @ 60 Cycles / Minute............ 7.2 l/min Noise Level @ 4 bar.................. 81.8 db(a) Specifications Lower Pump Material................. CF8M (316) Stainless Steel Plunger Material..................... See Plunger Options Below Cylinder Material.................... See Plunger Options Below Air Motor.......................... 65465-B Motor Repair Kit.................... 61268 Motor Diameter.................... 4-1/4 Stroke............................ 152 mm Air Inlet........................... 1/2 NPT(F) Exhaust Port...................... 1-1/4 NPT(F) Two-Ball Pump Model................ 66301-X4X Lower Pump Repair Kit.............. 637306-X43 Material Inlet....................... 1 NPT(F) 2 NPT(M) Material Outlet...................... 1 NPT(F) Weight............................ 19.5 kg Piston Pumps Ratio: 22:1 Bar: 224.4 (Max.) Type: 2-Ball Recommended Accessories Air F/R/L: C28241-810 Airline Oil: 62274 Air Motor Muffler: 91790 Wet Sol: 66333-B Wall Mount: 66 Floor/Follower Adapter: 67136 Floor Mount: 65138 Fluid Pressure (Bar) Ordering CYCLES PER MINUTE 0 50 150 200 70 Performance based on 5 poise oil at ambient temperature 180 8.3 bar 60 160 8.3 bar 140 50 120 40 80 60 40 20 6 5 0 4 8 4 - X 4 X Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Plungers 3 : 17-4 S. S. Hard Chrome Plated B : 17-4 S.S. Ultra Coated COATING 0 0 0 5 10 15 20 LITRES PER MINUTE DELIVERY 30 20 10 Air Consumption (litres/sec.)

Fluid Pressure (Bar) Performance 3", 22:1, Chop Check Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 44.8-244.4 bar Displacement Per Cycle.............. 31.1 cm 3 Cycles Per Litre..................... 32.1 Maximum Working Flow................3.7 l/min Noise Level @ 6.8 bar................ 85 db(a) Specifications Lower Pump Material................. Carbon Steel Plunger Material..................... 17-4 Stnls. steel Air Motor.......................... 66915 Motor Repair Kit.................... 637316 Motor Diameter.................... 3 Stroke............................ 76 mm Air Inlet........................... 1/4 NPTF-1 (f) Pump Model: Model NM2322E-11-P43.............. 67-P43 Model NM2322E-11-P48.............. 67-P48 Lower Pump Repair Kits: Model NM2322E-11-P43.............. 637290-P43 Model NM2322E-11-P48.............. 637290-P48 Material Inlet....................... Follower Plate Mounted Material Outlet...................... 1/2 NPT(F) Weight............................ 13 kg Ordering N M 2 3 2 2 E - 1 1 - P 4 X Packing / Plunger 3 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE Grooved Piston (Lower) 8 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE Single Lip Cup (Lower) CYCLES PER MINUTE 0 50 150 200 160 14 Performance based on 30 wt. gear oil at ambient temperature 140 12 8.3 bar 8.3 bar 120 10 8 80 6 60 40 20 0 0 0 1 2 3 4 5 6 LITRES PER MINUTE DELIVERY 4 2 Air Consumption (litres/sec.) NM2322E-11-P4X 857 mm 621 mm 430 mm 360 mm Recommended Accessories Air F/R/L: 128121-800 Airline Oil: 62274 Wet Sol: 66333-B Follower Plate: See Page 18 A.S.A.P. Packages: NM322R01-1 NP322L01-1 Ratio: 22:1 Bar: 244.4 (Max.) Type: Chop Check 33 3" (22:1) CS Extrusion Pumps

34 3" (22:1) SS Extrusion Pumps Ratio: 22:1 Bar: 244.4 (Max.) Type: Chop Check NM2322F-11-P4X 857 mm 621 mm 430 mm 360 mm Recommended Accessories Air F/R/L: 128121-800 Airline Oil: 62274 Wet Sol: 66333-B Follower Plate: 651841-1 A.S.A.P. Packages: NP322R02-1 NP322L02-1 Fluid Pressure (Bar) Performance 3", 22:1, Chop Check Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 44.8-244.4 bar Max. Rec d Cycles Per Minute.......... 120 Displacement Per Cycle.............. 31.1 cm 3 Cycles Per Litre..................... 32.1 Maximum Working Flow................3.7 l/min Noise Level @ 6.8 bar................ 85 db(a) Lower Pump Material................. 316 Stnls. Steel Plunger Material..................... 17-4 Stnls. Steel (Chrome Plated) Cylinder Material.................... 15-5 Stnls. Steel (Chrome Plated) Air Motor.......................... 66915 Motor Repair Kit.................... 637316 Motor Diameter.................... 3 Stroke............................ 76 mm Air Inlet........................... 1/4 NPTF-1 (F) Pump Model: Model NM23228-11-P43.............. 67101-P43 Model NM23228-11-P43.............. 67101-P48 Lower Pump Repair Kits: Model NM2322F-11-P43.............. 637291-P43 Model NM2322F-11-P48.............. 637291-P48 Material Inlet....................... Follower Plate Mounted Material Outlet...................... 1/2 NPT(F) Weight............................ 13 kg Ordering N M 2 3 2 2 F - 1 1 - P 4 X Packing / Plunger 3 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE Grooved Piston (Lower) 8 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE Single Lip Cup (Lower) CYCLES PER MINUTE 0 50 150 200 160 14 Performance based on 30 wt. gear oil at ambient temperature 140 8.3 bar 12 8.3 bar 120 10 8 80 6 60 40 20 Specifications 0 0 0 1 2 3 4 5 6 LITRES PER MINUTE DELIVERY 4 2 Air Consumption (litres/sec.)

Fluid Pressure (Bar) Performance 6", 23:1, 2-Ball Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 46.9-234.6 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 237.6 cm 3 Cycles Per Gallon (Litre).............. 4.2 Flow @ 60 Cycles / Minute............ 13.9 l/min Noise Level @ 4 bar.................. 84.8 db(a) Lower Pump Material................. CF8M (316) Stns. Steel Plunger Material..................... See Plunger Option Below Cylinder Material.................... See Plunger Option Below Air Motor.......................... 65665-B Motor Repair Kit.................... 61355 Motor Diameter.................... 6 Stroke............................ 152 mm Air Inlet........................... 1/2 NPTF Exhaust Port...................... 1-1/4 NPTF Two-Ball Pump Model................ 66300-X4X Lower Pump Repair Kit.............. 637305-X43 Material Inlet....................... 1 NPT(F) 2 NPT(M) Material Outlet...................... 1 NPTF Weight............................ 21 kg Ordering CYCLES PER MINUTE 0 20 40 60 80 120 200 90 Performance based on 5 poise oil at ambient temperature 180 8.3 bar 80 160 8.3 bar 70 140 120 80 60 40 20 Specifications 6 5 0 6 8 3 - X 4 X Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Plungers 3 : 17-4 S. S. Hard Chrome Plated B : 17-4 S.S. Ultra Coated COATING 60 50 40 30 20 10 Air Consumption (litres/sec.) 9 mm 650683-X4X 481 mm 322 mm Recommended Accessories Air F/R/L: C28241-810 Airline Oil: 62274 Air Motor Muffler: 91790 Wet Sol: 66333-B Wall Mount: 66 Floor/Follower Adapter: 67136 6" (23:1) SS Ratio: 23:1 Bar: 234.6 (Max.) Type: 2-Ball 35 Piston Pumps 0 0 0 10 20 30 40 50 LITRES PER MINUTE DELIVERY

36 4-1/4" (23:1) Extrusion Pumps Ratio: 23:1 Bar: 234.6 (Max.) Type: Chop Check 650492-X43-B 1310.6 mm 779.8 mm 449.6 mm Recommended Accessories Air F/R/L: C28241-810 Airline Oil: 62274 Air Motor Muffler: 91790 Wet Sol: 66333-B Floor Mount: 65138 Rams: Page 15 Fluid Pressure (Bar) Performance 4-1/4", 23:1, Chop Check Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 46.9-234.6 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 113 cm 3 Cycles Per Litre..................... 8.8 Flow @ 60 Cycles / Minute............ 6.8 l/min Noise Level @ 4 bar.................. 80 db(a) Specifications Lower Pump Material................. Carbon Steel (Nickel Plated) Plunger Material..................... 17.4 Stainless (Hard Chrome Plated) Cylinder Material.................... Carbon Steel (Nickel Plated) Air Motor.......................... 65465-B Motor Repair Kit.................... 61268 Motor Diameter.................... 4-1/4 Stroke............................ 152 mm Air Inlet........................... 1/2 NPT(F) Exhaust Port...................... 1-1/4 NPT(F) Chop Check Pump Model............. 66266-X43-B Lower Pump Repair Kit.............. 637074-X43-B Material Inlet....................... Bolted Flange Material Outlet...................... 1 NPT(F) Weight............................ 28.9 kg Ordering 6 5 0 4 9 2 - X 4 3 - B CYCLES PER MINUTE 0 50 150 200 250 250 90 Performance based on 90 wt. gear oil at ambient temperature 8.3 bar 80 200 150 50 Packings G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) 8.3 bar 0 0 0 5 10 15 20 25 30 LITRES PER MINUTE DELIVERY 70 60 50 40 30 20 10 Air Consumption (litres/sec.)

Fluid Pressure (Bar) Performance 6", 23:1, Chop Check Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 46.9-234.6 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 206.4 cm 3 Cycles Per Litre..................... 4.8 Flow @ 60 Cycles / Minute............ 12.4 l/min Noise Level @ 4 bar.................. 83 db(a) w/muffler Specifications Ordering CYCLES PER MINUTE 0 50 150 400 120 8.3 bar Performance based on 90 wt. gear oil at ambient temperature 350 300 250 200 60 150 50 Lower Pump Material................. Carbon Steel (Nickel Plated) Plunger Material..................... 17.4 Stnls. Steel (Hard Chrome Plated) Cylinder Material.................... Carbon Steel (Nickel Plated) Air Motor.......................... 65665-B Motor Repair Kit.................... 61355 Motor Diameter.................... 6 Stroke............................ 152 mm Air Inlet........................... 1/2 NPT(F) Exhaust Port...................... 1-1/4 NPT(F) Chop Check Pump Model............. 66243-X43-B Lower Pump Repair Kit.............. 637071-X43-B Material Inlet....................... Bolted Flange Material Outlet...................... 1 NPT(F) Weight............................ 30.4 kg 6 5 0 6 9 1 - X 4 3 - B Packings G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) 0 0 0 5 10 15 LITRES PER MINUTE DELIVERY 8.3 bar 80 40 20 Air Consumption (litres/sec.) 650691-X43-B 1310.6 mm 779.8 mm 449.6 mm Recommended Accessories Air F/R/L: C28241-810 Airline Oil: 62274 Air Motor Muffler: 91790 Wet Sol: 66333-B Floor Mount: 65138 Rams: Page 15 Ratio: 23:1 Bar: 234.6 (Max.) Type: Chop Check 37 6" (23:1) CS Extrusion Pumps

38 12" (30:1) CS Extrusion Pumps Ratio: 30:1 Bar: 183.6 (Max.) Type: Chop Check 650971-XX4-B 1301.7 mm 508 mm 797,7 mm Recommended Accessories Air F/R/L: 28353 Airline Oil: 62274 Air Motor Muffler: 66718 Wet Sol: 66333-B Floor Mount: 65139 Rams Page 15 Fluid Pressure (Bar) 0 250 200 150 50 Performance 12", 30:1, Chop Check Air Inlet Pressure Range.............. 6.1 bar Max. Fluid Pressure Range................ 183.6 bar Max. Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 662 cm 3 Cycles Per Litre..................... 1.5 Flow @ 60 Cycles / Minute............ 39.6 l/min Noise Level @ 4 bar.................. 88 db(a) w/muffler Specifications Lower Pump Material................. Carbon Steel Plunger Material..................... Carbon Steel Cylinder Material.................... Carbon Steel (Nickel Plated) Air Motor.......................... 66506 Motor Repair Kit.................... 637112 Motor Diameter.................... 12 Stroke............................ 152 mm Air Inlet........................... 3/4 NPT(F) Exhaust Port...................... 1-1/4 NPT(F) Chop Check Pump Model............. 66236-XX4-B Lower Pump Repair Kit.............. 637128-XX4-B Material Inlet....................... Bolted Flange Material Outlet...................... 1-1/2 NPT(F) Weight............................ 66.8 kg Ordering 6 5 0 9 7 1 - X X 4 - B Packings / Springs F4 : UHMW-PE/Leather Staggered (Upper), UHMW-PE (Lower), Multiple Wave Spring J3 : Polyurethane (Upper), UHMW-PE (Lower), No Spring P4 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower), Multiple Wave Spring R4 : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Multiple Wave Spring 10 20 CYCLES PER MINUTE 30 40 50 Performance based on 90 wt. gear oil at ambient temperature 0 0 0 10 20 30 40 LITRES PER MINUTE DELIVERY 60 140 120 80 60 40 20 Air Consumption (litres/sec.)

Fluid Pressure (Bar) Performance 4-1/4", 30:1, 2-Ball Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 61.2-306.1 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 90.1 cm 3 Cycles Per Litre..................... 11 Flow @ 60 Cycles / Minute............ 4.9 l/min Noise Level @ 4 bar.................. 81.8 db(a) Specifications Lower Pump Material................. CF8M Stnls. Steel Plunger Material..................... See Plunger Options Below Cylinder Material.................... See Plunger Options Below Air Motor.......................... 65465-B Motor Repair Kit.................... 61268 Motor Diameter.................... 4-1/4 Stroke............................ 152 mm Air Inlet........................... 1/2 NPT(F) Exhaust Port...................... 1-1/4 NPT(F) Two-Ball Pump Model................ 66302-X4X Lower Pump Repair Kit.............. 637307-X43 Material Inlet....................... 1 NPT(F) 2 NPT(M) Material Outlet...................... 1 NPT(F) Weight............................ 19.5 kg Ordering 6 5 0 4 8 5 - X 4 X Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Plungers 3 : 17-4 S. S. Hard Chrome Plated B : 17-4 S.S. Ultra Coated COATING CYCLES PER MINUTE 0 20 40 60 80 120 300 60 Performance based on 5 poise oil at ambient temperature 250 8.3 bar 8.3 bar 50 200 40 150 30 20 50 10 Air Consumption (litres/sec.) 650485-X4X 9.3 mm 481 mm 322 mm Recommended Accessories Air F/R/L: C28241-810 Airline Oil: 62274 Air Motor Muffler: 91790 Wet Sol: 66333-B Floor/Follower Adapter: 67136 Floor Mount: 65138 4-1/4" (30:1) SS Ratio: 30:1 Bar: 306.1 (Max.) Type: 2-Ball 39 Piston Pumps 0 0 0 2 4 6 8 10 LITRES PER MINUTE DELIVERY

40 8" (40:1) SS Piston Pumps Ratio: 30:1 Bar: 326.5 (Max.) Type: 2-Ball 650883-X4X 1106 mm 575 mm 322 mm Recommended Accessories Air F/R/L: 28353 Airline Oil: 62274 Air Motor Muffler: 92460 Wet Sol: 66333-B Floor/Follower Adapter: 67136 Rams: Page 15 Floor Mounts: 65138 Fluid Pressure (Bar) Performance 8", 40:1, 2-Ball Air Inlet Pressure Range.............. 2-8.1 bar Fluid Pressure Range................ 81.6-326.5 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 237.6 cm 3 Cycles Per Litre..................... 4.2 Flow @ 60 Cycles / Minute............ 13.9 l/min Noise Level @ 4 bar.................. 89.8 db(a) Lower Pump Material................. CF8M Stnls. Steel Plunger Material..................... See Plunger Options Below Cylinder Material.................... See Plunger Options Below Air Motor.......................... 66523 Motor Repair Kit.................... 66614 Motor Diameter.................... 8 Stroke............................ 152 mm Air Inlet........................... 3/4 NPT(F) Exhaust Port...................... 1-1/4 NPT(F) Two-Ball Pump Model................ 66300-X47 Lower Pump Repair Kit.............. 637305-X43 Material Inlet....................... 1 NPT(F) 2 NPT(M) Material Outlet...................... 1 NPT(F) Weight............................ 30.9 kg Ordering CYCLES PER MINUTE 0 20 40 60 80 350 120 8.3 bar Performance based on 5 poise oil at ambient temperature 300 8.3 bar 250 200 150 50 Specifications 6 5 0 8 8 3 - X 4 X Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Plungers 7 : 17-4 S. S. Hard Chrome Plated C : 17-4 S.S. Ultra Coated COATING 80 60 40 20 Air Consumption (litres/sec.) 0 0 0 5 10 15 20 LITRES PER MINUTE DELIVERY

Fluid Pressure (Bar) Performance 4-1/4", 43:1, Chop Check Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 87.7-438.7 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 45.8 cm 3 Cycles Per Litre..................... 21.7 Flow @ 75 Cycles / Minute............ 3.4 l/min Noise Level @ 4 bar.................. 80 db(a) Lower Pump Material................. Carbon Steel Plunger Material..................... 17.4 Stnls. Steel (Chrome Plated) Cylinder Material.................... Carbon Steel (Nickel Plated) Air Motor.......................... 65440 Motor Repair Kit.................... 61268 Motor Diameter.................... 4-1/4 Stroke............................ 101 mm Air Inlet........................... 1/2 NPT(F) Exhaust Port...................... 1/2 NPT(F) Pump Model: Model NM2322E-11-P43.............. 67-P43 Model NM2322E-11-P48.............. 67-P48 Lower Pump Repair Kits: Model NM2322E-11-P43.............. 637290-P43 Model NM2322E-11-P48.............. 637290-P48 Material Inlet....................... Follower Plate Mounted Material Outlet...................... 1/2 NPT(F) Weight............................ 20 kg Ordering CYCLES PER MINUTE 0 50 150 200 350 90 8.3 bar Performance based on 30 wt. gear oil at ambient temperature 300 80 250 200 50 40 150 30 20 50 Specifications 6 7 1 2 0 - P 4 X Packing P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) Plungers 3 : HD SS w/chrome plating and standard lower packing 8 : HD SS w/chrome plating and cup type lower packing 8.3 bar 70 60 10 Air Consumption (litres/sec.) 5.8 mm 67120-P4X 429 mm 619.7 mm Recommended Accessories Air F/R/L: C28241-810 Airline Oil: 62274 Air Motor Muffler: 91790 Wet Sol: 66333-B Follower Plate: Page 18 A.S.A.P. Packages: 650540-1 650542-1 4-1/4" (43:1) CS Ratio: 43:1 Bar: 438.7 (Max.) Type: Chop Check 41 Extrusion Pumps 0 0 0 1 2 3 4 5 6 LITRES PER MINUTE DELIVERY

42 4-1/4" (43:1) SS Extrusion Pumps Ratio: 43:1 Bar: 438.7 (Max.) Type: Chop Check 67121-P4X 5.8 mm 619.7 mm 429 mm Recommended Accessories Air F/R/L: C28241-810 Airline Oil: 62274 Air Motor Muffler: 91790 Wet Sol: 66333-B Follower Plate: 651841-1 A.S.A.P. Packages: 650541-1 650543-1 Fluid Pressure (Bar) Performance 4-1/4", 43:1, Chop Check Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 87.7-438.7 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 45.8 cm 3 Cycles Per Litre..................... 21.7 Flow @ 75 Cycles / Minute............ 3.4 l/min Noise Level @ 4 bar.................. 80 db(a) Specifications Lower Pump Material................. 15-5 Stnls. Steel Plunger Material..................... 17.4 Stnls. Steel (Chrome Plated) Cylinder Material.................... 15-5 Stnls. Steel (Chrome Plated) Air Motor.......................... 65440 Motor Repair Kit.................... 61268 Motor Diameter.................... 4-1/4 Stroke............................ 101 mm Air Inlet........................... 1/2 NPT(F) Exhaust Port...................... 1-1/4 NPT(F) Pump Model: Model NM23228-11-P43.............. 67101-P43 Model NM23228-11-P43.............. 67101-P48 Lower Pump Repair Kits: Model NM2322F-11-P43.............. 637291-P43 Model NM2322F-11-P48.............. 637291-P48 Material Inlet....................... Follower Plated Mounted Material Outlet...................... 1/2 NPT(F) Weight............................ 20 kg Ordering 6 7 1 2 1 - P 4 X Packing 3 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) CYCLES PER MINUTE 0 50 150 200 350 90 8.3 bar Performance based on 30 wt. gear oil at ambient temperature 300 80 250 200 50 40 150 30 20 50 0 0 0 1 2 3 4 5 6 LITRES PER MINUTE DELIVERY 8.3 bar 70 60 10 Air Consumption (litres/sec.)

Fluid Pressure (Bar) Performance 8", 44:1, Chop Check Air Inlet Pressure Range.............. 8.1 bar Max. Fluid Pressure Range................ 359.1 bar Max. Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 237.6 cm 3 Cycles Per Litre..................... 4.2 Flow @ 60 Cycles / Minute............ 14.3 l/min Noise Level @ 4 bar.................. 88 db(a) w/muffler Lower Pump Material................. Carbon Steel Plunger Material..................... Carbon Steel Cylinder Material.................... 17-4 Stnls. Steel (Chrome Plated) Air Motor.......................... 66523 Motor Repair Kit.................... 66614 Motor Diameter.................... 8 Stroke............................ 152 mm Air Inlet........................... 3/4 NPT(F) Exhaust Port...................... 1-14 NPT(F) Chop Check Pump Model............. 66243-X47-B Lower Pump Repair Kit.............. 637071-X47-B Material Inlet....................... Bolted Flange Material Outlet...................... 1 NPT(F) Weight............................ 40.4 kg Ordering CYCLES PER MINUTE 0 20 40 60 80 400 120 8.3 bar Performance based on 90 wt. gear oil at ambient temperature 350 8.3 bar 300 80 250 200 60 150 50 Specifications 6 5 0 8 9 1 - X 4 7 - B Packings G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) 0 0 0 5 10 15 LITRES PER MINUTE DELIVERY 40 20 Air Consumption (litres/sec.) 650891-X47-B 1328.4 mm 449.5 mm 698.5 mm Recommended Accessories Air F/R/L: 28353 Airline Oil: 62274 Air Motor Muffler: 92460 Wet Sol: 66333-B Floor Mount: 65138 Rams: Page 15 43 8" (44:1) CS Ratio: 44:1 Bar: 359.1 (Max.) Type: Chop Check Extrusion Pumps

44 6" (45:1) 650684-X4X 9 mm 481 mm 322 mm Performance 6", 45:1, 2-Ball Air Inlet Pressure Range.............. 2-8.3 bar Fluid Pressure Range................ 92.8-367.3 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 122.9 cm 3 Cycles Per Litre..................... 8.1 Flow @ 60 Cycles / Minute............ 7.2 l/min Noise Level @ 4 bar.................. 84.8 db(a) Specifications Lower Pump Material................. CF8M (316) Stnls. Steel Plunger Material..................... See Plunger Options Below Cylinder Material.................... See Plunger Options Below Air Motor.......................... 65665-B Motor Repair Kit.................... 61355 Motor Diameter.................... 6 Stroke............................ 152 mm Air Inlet........................... 1/2 NPT(F) Two-Ball Pump Model................ 66301-X4X Lower Pump Repair Kit.............. 637306-X43 Material Inlet....................... 1 NPT(F) 2 NPT(M) Material Outlet...................... 1 NPT(F) Weight............................ 21 kg Recommended Accessories Air F/R/L: C28241-810 Airline Oil: 62274 Air Motor Muffler: 91790 Wet Sol: 66333-B Wall Mounts: 66 Floor/Follower Adapter: 67136 Ordering 6 5 0 6 8 4 - X 4 X Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered Plungers 3 : 17-4 S. S. Hard Chrome Plated B : 17-4 S.S. Ultra Coated COATING Piston Pumps Ratio: 45:1 Bar: 367.3 (Max.) Type: 2-Ball Fluid Pressure (Bar) CYCLES PER MINUTE 0 20 40 60 80 120 400 90 350 300 250 200 150 Performance based on 5 poise oil at ambient temperature 8.3 bar 8.3 bar 50 10 0 0 0 2 4 6 8 10 12 14 LITRES PER MINUTE DELIVERY 80 70 60 50 40 30 20 Air Consumption (litres/sec.)

Fluid Pressure (Bar) Performance 6", 46:1, Chop Check Air Inlet Pressure Range.............. 2-10.2 bar Fluid Pressure Range................ 93.8-469.3 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 113 cm 3 Cycles Per Litre..................... 8.8 Flow @ 60 Cycles / Minute............ 6.4 l/min Noise Level @ 4 bar.................. 83 db(a) w/muffler Lower Pump Material................. Carbon Steel Plunger Material..................... 17.4 Stnls. Steel (Chrome Plated) Cylinder Material.................... Carbon Steel (Nickel Plated) Air Motor.......................... 65665-B Motor Repair Kit.................... 61355 Motor Diameter.................... 6 Stroke............................ 152 mm Air Inlet........................... 1/2 NPT(F) Exhaust Port...................... 1-1/4 NPT(F) Chop Check Pump Model............. 66266-X43-B Lower Pump Repair Kit.............. 637074-X43-B Material Inlet....................... Bolted Flange Material Outlet...................... 1 NPT(F) Weight............................ 30.4 kg Ordering CYCLES PER MINUTE 0 50 150 400 120 8.3 bar Performance based on 90 wt. gear oil at ambient temperature 350 300 250 200 60 150 50 Specifications 6 5 0 6 9 2 - X 4 3 - B Packings G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) 0 0 0 5 10 15 LITRES PER MINUTE DELIVERY 8.3 bar 80 40 20 Air Consumption (litres/sec.) 650692-X43-B 1310.6 mm 779.8 mm 449.6 mm Recommended Accessories Air F/R/L: C28241-810 Airline Oil: 62274 Air Motor Muffler: 91790 Wet Sol: 66333-B Floor Mount: 65138 Rams: Page 15 Ratio: 46:1 Bar: 469.3 (Max.) Type: Chop Check 45 6" (46:1) CS Extrusion Pumps

46 650685-X4X Performance 6", 60:1, 2-Ball Air Inlet Pressure Range.............. 2-6.9 bar 6" (60:1) Fluid Pressure Range................ 124-408 bar Max. Rec d Cycles Per Minute.......... 60 Displacement Per Cycle.............. 90.1 cm 3 Cycles Per Litre..................... 11.0 Flow @ 60 Cycles / Minute............ 4.9 l/min Noise Level @ 4 bar.................. 84.8 db(a) 9 mm Specifications Lower Pump Material................. CF8M (316) Stnls. Steel Plunger Material..................... See Plunger Options Below Cylinder Material.................... See Plunger Options Below Air Motor.......................... 65665-B Motor Repair Kit.................... 61355 Motor Diameter.................... 6 Stroke............................ 152 mm 481 mm Air Inlet........................... 1/2 NPT(F) Two-Ball Pump Model................ 66302-X4X 322 mm Lower Pump Repair Kit.............. 637307-X43 Material Inlet....................... 1 NPT(F) 2 NPT(M) Material Outlet...................... 1 NPT(F) Weight............................ 21 kg Recommended Accessories Air F/R/L: C28241-810 Airline Oil: 62274 Air Motor Muffler: 91790 Wet Sol: 66333-B Wall Mounts: 66 Floor/Follower Adapter: 67136 Ordering 6 5 0 6 8 5 - X 4 X Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered Plungers 3 : 17-4 S. S. Hard Chrome Plated B : 17-4 S.S. Ultra Coated COATING Piston Pumps Ratio: 60:1 Bar: 408 (Max.) Type: 2-Ball Fluid Pressure (Bar) CYCLES PER MINUTE 0 20 40 60 80 120 350 70 Performance based on 5 poise oil at ambient temperature 300 60 250 200 150 20 50 10 50 40 30 Air Consumption (litres/sec.) 0 0 0 2 4 6 8 10 LITRES PER MINUTE DELIVERY

Fluid Pressure (Bar) Performance 4 in 2, 1.2:1, Chop Check Hydraulic Inlet Pressure Range.......... 3.4-136 bar Fluid Pressure Range................ 4-181.5 bar Required H-power @ 50 cpm........... 3.2 @ 83 bar Hydraulic flow req d @ 50 cpm.......... 32.9 l/min Max. Rec d Cycles Per Minute.......... 50 Displacement Per Cycle.............. 114 cm 3 Volume / Cycle...................... 114 ml Cycles Per Litre..................... 8.78 Flow @ 50 Cycles / Minute............ 5.7 l/min Maximum Temperature Limit........... 54 C Specifications Lower Pump Material................. Carbon Steel (Nickel Plated) Plunger Material..................... Carbon Steel (Chrome Plated) Cylinder Material.................... Carbon Steel (Nickel Plated) Hydraulic Motor..................... 612626- Motor Repair Kit.................... 637148-1 Motor Size........................ 26.6 cm 2 Stroke............................ 152 mm Hydraulic Inlet..................... 1/2 NPT(F) Hydraulic Return................... 3/4 NPT(F) Chop Check Pump Model............. 66236-XX4-B Lower Pump Repair Kit.............. 637128-XX4-B Material Inlet...................... Bolted Flange Material Outlet...................... 1-1/2 NPT(F) Weight............................??.? Kg Ordering 650941-XX4-B Recommended Accessories 6 5 0 9 4 1 - X X 4 - B Floor Mount: 65139 Packings / Springs F : UHMW-PE/Leather Staggered (Upper), UHMW-PE (Lower) J : Polyurethane (Upper) UHMW-PE (Lower), P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE (Upper) Teflon (Lower) CYCLES PER MINUTE 0 20 40 60 80 120 180 160 137.9 bar Performance based on 30 wt. gear oil at ambient temperature 90 140 120 80 60 40 20 8 41.4 bar 0 0 0 10 20 30 40 50 60 70 LITRES PER MINUTE DELIVERY 80 70 60 50 40 30 20 10 Hydraulic Oil Consumption (litres/min.) 1344 mm 926 mm Wet Sol: 66333-B Rams: Page 15 508 mm 47 HYD" (1.2:1) CS Hydraulic Extrusion Pumps Ratio: 1.2:1 Bar: 181.5 (Max.) Type: Chop Check

48 HYD" (3.6:1) CS Hydraulic Extrusion Pumps Ratio: 3.6:1 Bar: 293.8 (Max.) Type: Chop Check 650935-X43-C 1206 mm 841 mm 450 mm Recommended Accessories Floor Mount: 65139 Wet Sol: 66333-B Rams: Page 15 Fluid Pressure (Bar) Performance 2 in 2, 3.6:1, Chop Check Hydraulic Inlet Pressure Range.......... 3.4-81.6 bar Fluid Pressure Range................ 12.2-293.8 bar Required H-power @ 50 cpm........... 3.2 @ 82.8 bar Hydraulic flow req d @ 50 cpm.......... 32.9 l/min Max. Rec d Cycles Per Minute.......... 50 Displacement Per Cycle.............. 113 cm 3 Volume / Cycle...................... 112 ml Cycles Per Litre..................... 8.8 Flow @ 50 Cycles / Minute............ 5.7 l/min Maximum Temperature Limit........... 54 C Lower Pump Material................. Carbon Steel Plunger Material..................... 17-4 Stns. Steel, (Chrome Plated) Cylinder Material.................... Carbon Steel (Nickel Plated) Hydraulic Motor..................... 67147 Motor Repair Kit.................... 637315 Motor Size........................ 13.3 cm 2 Stroke............................ 146 mm Hydraulic Inlet..................... 3/8 NPT(F) Hydraulic Return................... 1/2 NPT(F) Chop Check Pump Model............. 66266-X43-B Lower Pump Repair Kit.............. 637074-X43-B Material Inlet...................... Bolted Flange Material Outlet...................... 1 NPT(F) Weight............................ 30.9 Kg Ordering CYCLES PER MINUTE 0 20 40 60 80 120 350 60 Performance based on 30 wt. gear oil at ambient temperature 300 250 200 150 50 Specifications 6 5 0 9 3 5 - X 4 3 - C Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) 82.8 bar 62.1 bar 41.4 bar 20.7 bar 50 40 30 20 10 Hydraulic Oil Consumption (litres/min.) 0 0 0 2 4 6 8 10 12 14 LITRES PER MINUTE DELIVERY

49 Personal Notes

50 Personal Notes

MANUAL OR AUTOMATIC EXTRUSIONS APPLICATION? JUST CALL US!

Ingersoll-Rand offers a full range of diaphragm pumps. For further information contact Ingersoll-Rand or your nearest distributor Ingersoll-Rand European Sales Limited 5-7 Avenue Albert Einstein, Zone Industrielle, 78192 Trappes, France Tel: +33 (0)1 34 82 29 00 Fax: +33 (0)1 34 82 29 01 The Ingersoll-Rand distributor network gives you not only a superior product, but also a Total Quality service, to ensure your complete satisfaction. For additional information about the products shown in this catalogue, and assistance with selection, please contact your nearest Ingersoll-Rand distributor or Ingersoll-Rand office. DISTRIBUTOR: Nothing contained within this brochure is intended to extend any warranty or representation, expressed or implied, regarding the products described herein. Any such warranties or other items or conditions of sale of products shall be in accordance with Ingersoll-Rand' s standard terms and conditions of sale for such products, which are available upon request. Product improvement is a continuing goal at Ingersoll-Rand. Designs and specifications are subject to change without notice or obligation. Form No. E74 CPN 00850107 Printed in England 2000 by Ingersoll-Rand Company Printed on environmentally friendly Elemental Chlorine Free Paper