Installation Instructions SERIN Wall Mount Electronic Proximity Lavatory Faucet TE: Please refer to R30 Mounting Kit installation instructions #M4 prior to faucet installation. Certified to comply with ASME A.. 0 American Standard MODEL NUMBERS T04.34X T04.3X T0B.30X CAUTION: Use only American Standard supplied transformers and cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. Product No.'s & Options Specifications Faucet Installation Electrical Installation Start-up / Maintenance FAQ s / Troubleshooting Replacement Parts - - -0 0- TE TO INSTALLER: Please give this manual to the customer after installation. To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@lixilamericas.com For Parts, Service, Warranty or other Assistance, please call (44) CRT-TEAM / (44) -3 (In Canada: -00-3-03) (In Toronto Area only: -0-30-03) M3 REV.. (/)
Thank you for selecting American-Standard...the benchmark of fine quality for over 00 years.to ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping.. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.. Control box. Mixing Valve (optional, must be ordered separately). Control Box Cover Screws. Installation Instructions. Spout Assembly 3. Elbow Kit 4. Mounting Kit. Supply Hose Spout POWER KITS SOLD SEPARATELY Plug-In AC Power Kit PK00.PAC PRODUCT No.s All T04. SERIES Hard-Wired AC Power Kit Multi-AC Power Kit PK00.HAC PK00.MAC B a s e 3 P r o d u c t 4 0XTMV00 R30 MOUNTING KIT (Must have R30 Mounting Kit installed prior to Wall Mount faucet installation) Mixing Valve M3 REV.. (/)
Roughing-in Dimensions FINISHED WALL 0mm (-3/4) DIA. 0mm - mm MIN. (-/) - MAX. -/ 0-03mm Recommended (4" - " Recommended) GENERAL DESCRIPTION: Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on DC (battery/power pack) or AC permanent power (plug-in/hardwire). In-line strainer for solenoid is integral. Single inlet 3/ compression, built-in checks, and flexible stainless steel -/4" reach inlet hose for spout connection. Note: All plumbing and electrical wiring must be installed in accordance with applicable codes, regulations and standards. -/" MAX. (0mm) mm (3-3/) CAUTION: Use only American Standard supplied transformers and cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. *ELECTRICAL BOX (supplied by others) 3/" COMP. FINISHED FLOOR *RECOMENDED CONTROL BOX OR EQUIVALENT BY OTHERS CONTROL BOX IS ONLY REQUIRED FOR HARD-WIRED AC INSTALLATIONS (.3 &.3) 4" (0mm) SQ. X 3-/" (mm) DEEP CONTROL BOX Hubbel-RACO # OR EQUAL (BY CONTRACTOR). RECOMMENDED TOOLS Slip Jaw Pliers Adjustable Wrench 3 Plumbers' Putty or Caulking 4 Phillips Screwdriver Flat Blade Screwdriver Electric Drill & /4" Drill Bit Tape Measure FAUCET INSTALLATION 3 4 0' SPOUT ASSEMBLY INSTALLATION; Fig. CAUTION Turn off hot and cold water supplies before beginning. Remove both MOUNTING SCREWS (), then remove upper PLASTIC GUARD (). Remove the CORD HOLDER (3a) and CABLE HOLDER (4a) from the PLASTER GUARD (). IMPORTANT: Secure the CORD HOLDER (3a) and the CABLE HOLDER (4a) from falling back through the hole in the wall. Fig. 3a a 4a a. Remove the two EXTENSION CABLE ENDS (a) from the CABLE HOLDER (4a). IMPORTANT: Secure the CORD HOLDER (3a) and the EXTENSION CABLES (a) from falling back through the hole in the wall. 3b 3. Remove the CORD HOLDER (3b) and CABLE HOLDER (4b) from the two bottom PLASTER GUARDS ().Use a flat blade screwdriver to break off the two ends of the lower PLASTER GUARDS () flush with the finished wall. IMPORTANT: Be carefull not to damage the wire cables. Secure the CORD HOLDER (3b) and the CABLE HOLDER (4b) from falling back through the holes in the wall. Remove the two EXTENSION CABLE ENDS (b) from the CABLE HOLDER (4b). b 4b b M3 REV.. (/)
a INSTALL SPOUT MOUNTING KIT; Fig.. Make sure that SEAL () is installed into the groove on the back of the MOUNTING FLANGE (). Feed the CORD HOLDER (3a) and the EXTENSION CABLES (a) through the MOUNTING FLANGE ().. Install the MOUNTING FLANGE () to the wall with three SCREWS () that thread into the MOUNTING PLATE (0) within the wall. DO T fully tighten the SCREWS (). HAND TIGHTEN ONLY. Fig. 3a a 0 b INSTALL SPOUT ASSEMBLY; Fig. 3 Fig. 3. Slide SPOUT ESCUTCHEON () onto SPOUT ().. Slide COMPRESSION RING (3) and COMPRESSION SEAL (4) onto SPOUT (). 3. Connect SPOUT HOSE () onto CORD HOLDER (3a) by pressing until secure connection is achieved. 3 4 3a c SECURE WIRE CONNECTIONS; Fig. 4 Fig. 4. Connect the FAUCET SENSOR CONNECTORS () to the EXTENSION CABLES (a), and secure the connections by installing into CONNECTOR HOUSINGS () as shown. Rotate the END CAPS () to secure the connection within the CONNECTOR HOUSINGS ().. Pull the bottom end of EXTENSION CABLES (b) so that the CONNECTOR HOUSINGS () are inside the wall. 4. Pull bottom CORD HOLDER (3b) and fish SPOUT HOSE () through the wall and out through the bottom wall opening ().. Cut the CORD HOLDER (3a) off the end of the SPOUT HOSE () as shown. IMPORTANT: Secure the SPOUT HOSE () from falling back through the wall opening (). a 3b 3a CUT SPOUT HOSE b 3 M3 REV.. (/)
d ALIGN SPOUT ASSEMBLY; Fig.. Align and push SPOUT () through hole, loosely installed MOUNTING FLANGE () and MOUNTING PLATE (0).. Once MOUNTING FLANGE () is aligned with MOUNTING PLATE (0) opening, tighten the three MOUNTING FLANGE SCREWS (). (Tighten each screw little by little to avoid missalignment!) Fig. SPOUT LENGTH 0mm - mm MIN. (-/) - MAX. -/ 0 3. Align and slide and COMPRESSION SEAL (4) and COMPRESSION RING (3) to MOUNTING FLANGE (). e SECURE SPOUT ASSEMBLY; Fig. 3 4 0. Once MOUNTING FLANGE () is installed, move the SPOUT () in or out to determine desired spout length from finished wall. Note: The Min. is 0mm, (-/) and the Max. is mm, (-/) from the finished wall to center of the spout end.. Tighten COMPRESSION RING (3) to MOUNTING FLANGE () by tightening the three COMPRESSION RING SCREWS (0) with HEX WRENCH () supplied. This will fix SPOUT () length from finished wall. 3. Push ESCUTCHEON () to MOUNTING FLANGE () and hand tighten to complete spout installation. 3 4 Fig. 3 0 0mm - mm MIN. (-/) - MAX. -/ 4 M3 REV.. (/)
INSTALL SUPPLY ELBOW ASSEMBLY & CONTROL BOX; Fig. and Fig. a Fig. 3. Install HOSE CLAMP () onto SPOUT HOSE (). Install SPOUT HOSE () onto ELBOW NIPPLE (3). Fully tighten HOSE CLAMP () to secure SPOUT HOSE () to ELBOW ASSEMBLY (4). Fig... Using the ANCHORS () and SCREWS () supplied, attach ELBOW ASSEMBLY (4) to finished wall, covering the hole in wall. Fig.. 3. Remove CONTROL BOX COVER (). Feed EXTENSION CABLES (b) THROUGH GROMMET () in back of CONTROL BOX (). (Refer to VIEW A ). Hold the CONTROL BOX () so that it covers the wall opening and mark the four mounting hole locations as shown. Fig. a. 4. It is recommended that the CONTROL BOX () be secured to a wall stud or cross brace within the wall using the SCREWS (30) supplied. If the CONTROL BOX () is to be installed on tile or plaster walls, the ANCHORS (3) and SCREWS (30) should be used. Fig. a VIEW A 4 30 VIEW A b 3 TE: Find plastic bag containing 4 MX screws to be used for securing the CONTROL BOX COVER () when installation is complete. Fig. 3 CONNECT SPOUT HOSE TO CONTROL BOX; Fig.. Connect G / end of SUPPLY HOSE (3) to the ELBOW ASSEMBLY (4). Tighten with adjustable wrench to make a water tight connection. LAVATORY RIM OR MOUNTING SURFACE. Connect G 3/ end of SUPPLY HOSE (3) to nipple on top of CONTROL BOX (). Tighten with adjustable wrench to make a water tight connection. 3. IMPORTANT: INSERT FIBER WASHER (33) INTO SUPPLY NUT (34) ON CONTROL BOX (). CONTROL BOX FOR HARDWIRE INSTALLATION (supplied by others) COLD WATER OR TEMPERED WALL SUPPLY 3 4. Connect FLEXIBLE SUPPLY (3) to bottom SUPPLY NUT (34). Connect other end directly to wall supply. Connection is G 3/" compression. Note: FLEXIBLE SUPPLY (3) measures 0" from the bottom of the CONTROL BOX () base. If additional supply length is required, installer must purchase parts separately. If FLEXIBLE SUPPLY (3) is too long, loop to avoid kinking. 4 34 33 3 TE: If using Mixing Valve (optional) See Sheet #M0 for installation instructions. " TO " (mm TO 30mm) M3 REV.. (/)
ELECTRICAL INSTALLATION Fig. Product Page Plug-in AC Power Kit (PK00.PAC) Hard-Wired AC Power Kit (PK00.HAC) MULTI-AC Power Kit (PK00.MAC) Fig. a Fig. b A PWRX & STANDARD BATTERY; Fig.. Remove CONTROL BOX COVER () from CONTROL BOX (). Fig.. 3 4. Feed the EXTENSION CABLE (3) from the Faucet through SIDE GROMMET (4). Fig. a. 3. Connect SOLEID CABLE () to EXTENSION CABLE (3) from the Faucet. Fig. a. 4. Insert BATTERY () into BATTERY HOLDER (), make sure the shape of the BATTERY () follows the shape of the BATTERY HOLDER () and terminal end is inserted first. Fig. b. Fig. c a INSTALL BATTERY STANDARD BATTERY CR-P. Connect the BATTERY CONNECTOR (a) from the Standard or PWRX Battery to EXTENSION CABLE () as shown. Fig. c. Place Standard Battery or PWRX into Housing. Fig. d. PWRX. Replace CONTROL BOX COVER (). Tighten cover screws firmly. a Fig. d STANDARD BATTERY PWRX CAUTION: Use only American Standard supplied transformers and cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. M3 REV.. (/)
B AC VERSIONS (HARDWIRE / PLUG-IN); Fig. Fig. CAUTION Disconnect AC power supply before opening CONTROL BOX. TE: For AC installation, make power supply connection before mounting CONTROL BOX (3) to wall. 3. Remove CONTROL BOX COVER (). Feed the EXTENSION CABLES () from the Faucet through the top of ENCLOSURE (3). Fig.. FOR PLUG-IN HOOKUP ONLY a. Insert POWER CORD () through POWER SUPPLY GROMMET () Fig. a. 3a. Insert POWER CORD () through side GROMMET () as shown. Fig. a. 4a. Connect one of the " EXTENSION CABLES () to SOLEID CABLE () and the other to the SINGLE AC ADAPTER (0). Connect POWER CORD () to SINGLE AC ADAPTER (0) and install CONNECTOR LOCKING DEVICE (). Fig. a. Fig. a a. Mount CONTROL BOX to wall. Replace CONTROL BOX COVER (). Tighten cover screws firmly. a. Plug AC POWER SUPPLY into wall outlet. PLUG INTO WALL OUTLET FOR HARDWIRE HOOK-UP ONLY; b. Insert one end of the 0' EXTENSION (0a) through POWER SUPPLY GROMMET (). Fig. b. 3b. Insert 0' EXTENSION (0a) through side GROMMET () as shown. Fig. b. Fig. b 0 4b. Connect one of the " EXTENSION CABLES () to SOLEID CABLE () and the other to the 0' EXTENSION CABLE (0a). Install CONNECTOR LOCKING DEVICE (). Fig. b. b. Mount CONTROL BOX () to wall. Replace CONTROL BOX COVER (). Tighten cover screws firmly. Contractor to supply ELECTRICAL BOX () and power to POWER SUPPLY (3). 0a b. Mount POWER SUPPLY (3) onto ELECTRICAL BOX (). Connect connections to POWER SUPPLY CONNECTIONS (4). Fig. c. b. Connect the 0' EXTENSION (0b) to the POWER SUPPLY CABLE (). Fig. c. CAUTION: Use only American Standard supplied cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. Fig. c 0b 0' EXTENSION FROM ELECTRICAL BOX WITH POWER SUPPLY 4 BLACK & WHITE POWER CONNECTIONS 3 M3 REV.. (/)
Fig. 4 Unit # Already installed Unit # Unit #3 0 ft. EXTENSION CABLE AC POWER SUPPLY BLACK & WHITE POWER CONNECTIONS OR *MAXIMUM OF UNITS PER AC POWER SUPPLY. 0' MAXIMUM CABLE LENGTH BETWEEN UNITS. C FOR AC-VERSION (MULTI HOOK-UP); Fig. 4 and Fig. 4a. Remove COVERS from all CONTROL BOX (). Fig. 4 and Fig. 4a. Fig. 4a Unit # Detail. Remove SOLID BLACK PLUG GROMMET () from left side of all CONTROL BOX (). Replace with GRAY GROMMET (). (Supplied with each Faucet). Fig. 4 and Fig. 4a. 3. Feed the EXTENSION CABLE (3) from the Faucet through GROMMET (4) and connect it to the SOLEID CABLE (). Fig. 4 and Fig. 4a. a 4a 4b b 4. Feed the EXTENSION CABLE () from the Faucet through GROMMET (4a) and connect to either of the two terminals at the one end of the Y-ADAPTER (3). Connect the 0 ft. EXTENSION (a) to the other terminal at the same end of the Y-ADAPTER (3). Fig. 4 and Fig. 4a. 3. Feed the other end of the 0 ft.extension (b) through the two GRAY GROMMETS (4a and 4b) and connect to the single terminal end of the next unit s Y-ADAPTER (3). Place Y-ADAPTER (3) into CONTROL BOX () as shown in Fig. 4 and Fig. 4a.. Repeat Steps above for each additional Unit, for a Max. of Units on one AC POWER SUPPLY. 3 4. Replace CONTROL BOX COVERS. Tighten cover screws firmly. CAUTION: Use only American Standard supplied transformers and cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. AC POWER YOU CAN USE EITHER THE PLUG-IN OR HARD-WIRED TRANSFORMER. M3 REV.. (/)
START-UP / MAINTENANCE A HAND WASH SENSOR OPERATION; Fig. Prior to making power connection, make sure detection zone is not obstructed. Sensor is self adjusting. Keep detection zone clear for!seconds after power is connected. Fig. When the Sensor detects a user, the water immediately starts to flow. Water flow will stop. seconds after user is out of sensor range. This comfort timer allows the user to move his hands without the flow cycling on and off. As a precaution, a safety timer will turn off the water after the sensor has been blocked for seconds. Water flow will resume when the blockage is removed from the detection zone and the sensor is activated again. B HOW TO INSTALL AND CHANGE BATTERY; Fig.. Remove COVER from CONTROL BOX ().. Disconnect BATTERY HOLDER (3) from SENSOR CABLE (). 3. Remove old BATTERY from BATTERY HOLDER (3). Install new BATTERY () making sure the terminal side is inserted first and shape of the battery follows the shape of the BATTERY HOLDER (3). Prior to making power connection, make sure detection zone is not obstructed. Sensor is self adjusting. Keep detection zone clear for!seconds after power is connected. 4. To change PWRX BATTERY PACK (4), unplug and replace with new Power Pack. DETECTION ZONE: BETWEEN SPOUT AND BASE OF SINK Fig. 4 CR-P 3. Reconnect BATTERY HOLDER (3) to SENSOR CABLE ().. Replace CONTROL BOX COVER. Tighten cover screws firmly. Fig.3 C HOW TO CLEAN FILTER ASSEMBLY; Fig. 3 CAUTION Before opening CONTROL BOX disconnect AC power supply. STANDARD BATTERY /" SOCKET. Remove CONTROL BOX COVER.. Close SUPPLY STOP (3) with 4mm Hex wrench. Note: Activate sensor to keep water flowing out of faucet while shutting off. 3. Unthread FILTER ASSEMBLY () using a /" socket. 4. Pull out the FILTER ASSEMBLY (), remove and clean white debris cup and filter screen.. Install the FILTER ASSEMBLY () back in its place and tighten with a /" socket. Caution: Do not over tighten. 3 FILTER SCREEN WHITE DEBRIS CUP. Open SUPPLY STOP (3) with 4mm Hex wrench.. Replace CONTROL BOX COVER. Tighten cover screws firmly. M3 REV.. (/)
D HOW TO CLEAN AND REMOVE THE AERATOR OR SPRAY; Fig. 4. Remove AERATOR or SPRAY HOUSING () with KEY supplied with faucet. Fig. 4. Remove AERATOR or SPRAY () from HOUSING (). 3. Clean the AERATOR or SPRAY SCREEN (). 4. Reassemble and install into spout end. Be sure the black seal washer is in place. KEY E HOW TO CLEAN FLOW REGULATOR; Fig.. Remove SUPPLY HOSE (0) from SPOUT ELBOW ASSEMBLY (). Pull out FLOW REGULATOR () from SPOUT ELBOW ASSEMBLY ().. Clean FLOW REGULATOR (). Replace FLOW REGULATOR () and reassemble SUPPLY HOSE (0) to SPOUT ELBOW ASSEMBLY (). Fig. RINSE TO CLEAN FLOW REGULATOR 0 GENERAL CLEANING; Fig. F Fig.. Only use a damp, soft cloth to clean the spout and the sensor.. For tougher dirt, use a soft cloth with diluted dish washing detergent. Wipe the area using a wet cloth and dry using a soft cloth. CAUTION Do not scratch the sensor when cleaning. Avoid using any abrasives or harsh detergents or chemicals. FAQ'S Q: How will I know if the battery needs to be replaced? A: Valve will not open and sensor will continuously blink times interrupted by a pause for up to days. Q: Why has the flow rate of the faucet reduced significantly? A: The filter assembly, flow regulator or areator/spray may be clogged. Check and clean. Refer to Start-up/Maintenance, sections C, D and E. Q: Why doesn t the water flow out of faucet when I'm within the sensor detection zone? A: Battery may need replacement. Check. If sensor continuously blinks times interrupted by pause, replace battery or call () -. Q: What is the normal operating pressure range? A: Faucet will operate with supply pressures ranging from 0-0 psi. 0 M3 REV.. (/)
TROUBLESHOOTING FLOW CHARTS UNIT DOES T FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? YES OPEN EXTERNAL SUPPLY STOPS. IS INTERNAL SUPPLY STOP OPEN? OPEN INTERNAL SUPPLY STOP. (HEX KEY NEEDED) YES REPEATED DOUBLE FLASH ON SENSOR? RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR SECONDS? YES REPLACE SOLEID YES CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR. WATER IS CONTINUOUSLY RUNNING RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR SECONDS? CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR. YES REPLACE SOLEID LOW FLOW ISSUES ARE INTERNAL & EXTERNAL SUPPLY STOPS FULLY OPEN? FULLY OPEN INTERNAL & EXTERNAL SUPPLY STOPS BY TURNING COUNTER CLOCKWISE. YES LOW FLOW COULD BE CAUSED BY DEBRIS IN THE FILTER ASSEMBLY, FLOW REGULATOR OR AERATOR/SPRAY. REMOVE, CLEAN AND INSERT BACK TO ORIGINAL POSITION. HOT LINE FOR HELP For toll-free information and answers to your questions, call: (44) CRT-TEAM / (44) -3 Mon. - Fri. :00 a.m. to :00 p.m. EST Saturday 0:00 a.m. to 4:00 p.m. EST IN MEXICO 0-00-3-00 IN CANADA -00-3-03 (TORONTO -0-30-03) Weekdays :00 a.m. to :00 p.m. EST Product names listed herein are trademarks of AS America, Inc. 0 To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@lixilamericas.com M3 REV.. (/)