SIREN DRIVER BOARD. Free running siren activated by the application of a V DC power source. This module is capable of driving a maximum of 2 x 8 ohm 10W speakers and produces approximately 110 db at one metre. Security alarms, warning systems. Supply voltage - V DC. Output level - 110 db at one metre. Capacity - 2 x 8 ohm 10w horn speakers. Termination - 4 way screw terminal. Mounting - self-adhesive standoffs or housing. Reverse polarity protection on the V DC input. Back EMF diode protection on the speaker output. Red led indicates power is on and siren operating. +Vdc input MCM ELECTRICS PTY. LTD. LSP-PCBS1.PM4
FLASHER DC OUTPUT BOARD. On application of thev DC input, the output will be pulsed at 1HZ (maximum load of 1A). Security alarms, warning systems. Supply voltage Output level Capacity Termination Mounting - V DC. - Switching from gnd to V DC. - V DC @ 1A maximum. - 4 way screw terminal. - Self-adhesive standoffs or housing. Reverse polarity protection on the V DC input. Back EMF diode protection on the flasher output. Red led indicates power is on and output flashing. load MCM ELECTRICS PTY. LTD. LSP-PCBS2.PM4
FLASHER RELAY OUTPUT BOARD. On application of the V DC input, the output will be pulsed at 1HZ (maximum load of 1A). Relay will operate at a time constant of 0.5 seconds on and 0.5 seconds off. Security alarms, warning systems. Supply voltage - V DC. Output level - Switching from gnd to V DC. Capacity - V DC @ 1 AMP maximum Relay rating - Max. switching power 150W - Max. switching voltage 30V DC - Max. switching current 5A - Min. voltage and current 5V DC 0.1A Termination - 4 way screw terminal. Reverse polarity protection on the V DC input. Back EMF diode protection on the flasher output. Red led indicates power is on and output flashing. Voltage Free Contacts load Output V dc pulsed MCM ELECTRICS PTY. LTD. LSP-PCBS3.PM4
FUSE DISTRIBUTI BOARD. Upon application of the V DC in, there will be four individually fuse protected outputs rated at 2 AMPS each. Security alarms, any application requiring seperately fused supplies. Supply voltage Output Rating Termination Mounting - V DC. - V DC. at 2 AMPS. - 10 way screw terminal. - self-adhesive standoffs or housing. Individual 2 AMP fuses on all four outputs. vdc OUT1 OUT3 OUT2 vdc vdc vdc OUT4 MCM ELECTRICS PTY. LTD. LSP-PCBS4.PM4
AC SPDT RELAY BOARD. On application of the 16V AC or V DC input, the relay will operate until the power is removed. Security alarms, any application requiring the operation of a spdt relay. Supply voltage - 16V AC/V DC. Relay rating - Max. switching power 150W - Max. switching voltage 30V DC - Max. switching current 5A Termination - 5 way screw terminal. Mounting - Self-adhesive standoffs or housing Red led indicates power is on and relay is energised Voltage Free Contacts MCM ELECTRICS PTY. LTD. LSP-PCBS5.PM4
DC SPDT RELAY BOARD. On application of the V DC input, the relay will operate until the V DC is removed. Security alarms, any application requiring the operation of a spdt relay. Supply voltage - V DC. Relay rating - Max. switching power 150W - Max. switching voltage 30V DC - Max. switching current 5A Termination - 5 way screw terminal. Reverse polarity protection on the V DC input. Red led indicates power is on and relay is energised. Voltage Free Contacts MCM ELECTRICS PTY. LTD. LSP-PCBS6.PM4
AC DPDT RELAY BOARD. On application of the 16V AC or V DC input, the relay will operate until the power is removed. Security alarms, any application requiring the operation of a dpdt relay. Supply voltage - 16V AC/V DC. Relay rating - Max. switching power 60W - Max. switching voltage 220V DC - Max. switching current 2A - Max. Carrying current 3A Termination - 8 way screw terminal. Mounting - Self-adhesive standoffs or housing Red led indicates power is on and relay is energised. Voltage Free Contacts MCM ELECTRICS PTY. LTD. LSP-PCBS7.PM4
DC DPDT RELAY BOARD. On application of the V DC input, the relay will operate until the V DC is removed. Security alarms, any application requiring the operation of a dpdt relay. Supply voltage - V DC Relay rating - Max. switching power 60W Max. switching voltage 220V DC Max. switching current 2A Max. carrying current 3A Termination - 8 way screw terminal. Reverse polarity protection on the V DC input. Red led indicates power is on and relay is energised. output led Voltage Free Contacts MCM ELECTRICS PTY. LTD. LSP-PCBS8.PM4
CLUTCH RELAY BOARD. On power up the relay will not be energised. On application of +V DC to the +TR terminal or 0V to the -TR terminal the relay will toggle once. On subsequent triggering the relay will toggle again. Security alarms, any application requiring the use of multiple push buttons, keyswitches, coded entry units. Supply voltage - V DC Relay rating - Max. switching power 150W Max. switching voltage 30V DC Max. switching current 5A Min. voltage and current 5V DC 0.1A Termination - 8 way screw terminal. Reverse polarity protection on the V DC input. Red led indicates power is on and relay is energised. Voltage Free Contacts MCM ELECTRICS PTY. LTD. LSP-PCBS9.PM4
TIMER BOARD. 1 of 2 Options: Delay to operate timer. Operate, delay to release timer. * Delay to operate: Link LK1 position 2. Upon application of a positive or negative trigger the relay will remain de-energised for a period of time dependant on the setting of the dipswitches. * Delay to release: Link LK1 position 3. Upon application of a positive or negative trigger the relay will energise energised for a period of time dependant on the setting of the dipswitches. Security alarms, any application requiring the operation of a SPDT relay for a period of time or after a specified time. Supply voltage- V DC Relay rating - Max. switching power 150W Max. switching voltage 30V DC Max. switching current 5A Termination - 8 way screw terminal. Reverse polarity protection on the V DC input. Red led indicates relay is energised. +RST - Not used. -TR - Negative trigger (0-3V). +TR - Positive trigger (7-V). Pot Adjustments position 1 position 2 position 3 LK1 RV1 SW1 Min Max Voltage Free Contacts MCM ELECTRICS PTY. LTD.
2 Minimum Minimum Maximum Maximum Dipswitch Settings Dipswitch Settings Potentiometer Adjustments Potentiometer Adjustments Seconds Seconds 0 0 6 6 46 46 50 50 50 50 52 52 18 18 38 38 20 20 46 46 2 32 32 30 30 0 TIMER BOARD. TIMER BOARD. 1 3 4 Minutes Minutes 0 1 2 3 4 5 6 7 10 10 11 11 13 13 15 15 16 16 17 17 18 18 Minutes Minutes 1 2 3 4 5 6 7 8 11 11 13 13 14 14 16 16 17 17 18 18 19 19 Seconds Seconds 0 0 46 46 58 58 52 52 52 52 26 26 34 34 42 42 42 42 20 20 30 30 43 43 42 42 MCM ELECTRICS PTY. LTD. MCM ELECTRICS PTY. LTD.
FULL FUNCTI TIMER / CLUTCH BOARD. 1 of 2 Options: Delay to operate timer. Operate, delay to release timer. Clutch relay * Timer - Delay to operate: Link LK1 position 2. Upon application of a positive or negative trigger the relay will remain de-energised for a period of time dependant on the setting of the dipswitches. * Timer - Delay to release: Link LK1 position 3. Upon application of a positive or negative trigger the relay will energise energised for a period of time dependant on the setting of the dipswitches. * Clutch relay: Link LK1 position 1. On power up the relay will not be energised. On application of +V DC to the +TR terminal or 0V to the -TR terminal the relay will toggle once. On subsequent triggering the relay will toggle again. Supply voltage - V DC Relay rating - Max. switching power 150W Max. switching voltage 30V DC Max. switching current 5A Termination - 8 way screw terminal. Reverse polarity protection on the V DC input. Red led indicates relay is energised. +RST - Not used. -TR - Negative trigger (0-3V). +TR - Positive trigger (7-V). Pot Adjustments position 1 position 2 position 3 LK1 RV1 SW1 Min Max Voltage Free Contacts MCM ELECTRICS PTY. LTD. LSP-PCBS.PM4
1AMP POWER SUPPLY BOARD. 1 Amp 13.7 Volts DC power supply, open collector outputs via 10 ohm resistors for Mains Fail and Mains On. Battery output for Battery backup. Security alarms, any application requiring 13.7 Vdc at 1 Amp. Supply Voltage - 16V AC. Output Voltage - Factory set to 13.7 Vdc. Battery Voltage - 13.7 Vdc (Current Limited). Termination - 8 way screw terminal. Varistor across AC input, 2 Amp fuse protected DC output, Battery output is Current Limited for protection. Red led indicates Mains on. 10 ohm Mains on 0V 10 ohm Mains fail 0V Mains fail and Mains on output stage. Mains on Mains fail load MCM ELECTRICS PTY. LTD. LSP-PCBS13.PM4
MICROPHE PRE-AMP BOARD. Security alarms, any application requiring 13.7 Vdc at 1 Amp. Supply Voltage - V DC. Termination - 3 way screw terminal. Mounting - Affixed to electrical wall plate by MCM. Varistor across AC input, 2 Amp fuse protected DC output, Battery output is Current Limited for protection. Red led indicates Mains on. Microphone Input input +V dc To amplifier MCM ELECTRICS PTY. LTD. LSP-PCBS14.PM4
1AMP POWER SUPPLY BOARD. 1 Amp 13.7 Volts DC power supply, open collector outputs via 10 ohm resistors for Mains Fail and Mains On. Battery output for Battery backup. Security alarms, any application requiring 13.7 Vdc at 1 Amp. Supply Voltage - 16V AC. Output Voltage - Factory set to 13.7 Vdc. Battery Voltage - 13.7 Vdc (Current Limited). Termination - 8 way screw terminal. Varistor across AC input, 2 Amp fuse protected DC output, Battery output is Current Limited for protection. Red led indicates Mains on. +RST - Not used. -TR - Negative trigger (0-3V). +TR - Positive trigger (7-V). Pot Adjustments position 1 position 2 position 3 LK1 RV1 SW1 Min Max Voltage Free Contacts MCM ELECTRICS PTY. LTD. LSP-PCBS15.PM4