Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE OL-AL(MDB)-TL2-EN TL2 AVAILABLE FOR : OL-MDB-ALL Rev. Date: April 08, 2016 Doc. No.: ##28069## U.S. PATENT NO. 8,856,780 The brand names and logos found in this guide are property of their respective owners. NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
Page 2 of 11 OL-AL(MDB)-TL2-EN Doc. No.: ##28069## 20160407 INSTALL TYPE SELECTION FEATURES MAKE MODEL NOTE I Keyless and smartkey systems will remain functional during remote start. YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS PUSH TO START CTRL ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) TRUNK/HATCH RELEASE POWER LIFTGATE TACHOMETER OUTPUT BRAKE PEDAL STATUS OUTPUT E-BRAKE OUTPUT DOOR STATUS OUTPUT TRUNK STATUS OUTPUT HOOD STATUS OUTPUT* TOYOTA LEXUS CT200h 11-15 3 GX460 10-15 2 HS250h 10-12 3 RX350 10-15 2 RX450h 10-15 2 4Runner 10-16 2 Prius 10-15 3 Prius V 12-16 3 Sienna 11-16 2 Venza 09-16 1 * Available only if vehicle is equipped with factory hood switch.
Page 3 of 11 OL-AL(MDB)-TL2-EN Doc. No.: ##28069## 20160407 COMPONENT LOCATOR A B C D
Page 4 of 11 OL-AL(MDB)-TL2-EN Doc. No.: ##28069## 20160407 TYPE 1 - CROSS REFERENCE CHART - 1 OF 1 MAKE MODEL TOYOTA YEAR DESCRIPTION NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR CanH D1 ~ 16 pin 06 Yellow (DATA) OBDII D CanL D1 ~ 16 pin 14 White (DATA) OBDII D 12V D17 ~ 07 pin 07 Pink (+) Black connector at steering lock B Venza 09-16 Ignition D17 ~ 07 pin 06 LtGreen (+) Black connector at steering lock B SLP D17 ~ 07 pin 04 Purple (-) Black connector at steering lock B TX D49 ~ 28 pin 22 Blue (DATA) Main body ECU, back side A RX D49 ~ 28 pin 23 Black (DATA) Main body ECU, back side A Parking D50 ~ 26 pin 23 Red (-) Main body ECU, back side A D13 ~ 14 pin 07 Blue (-) Push to start button C
Page 5 of 11 OL-AL(MDB)-TL2-EN Doc. No.: ##28069## 20160407 TYPE 1 - WIRING DIAGRAM MAIN BODY ECU BACK SIDE RX WARNING: DO NOT CONNECT ANY OTHER ACCESSORY,IGNITION OR START FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLING THE REQUIRED VEHICLE POWER AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. 18 19 20 21 22 23 24 25 26 7 8 9 10 11 12 13 14 15 16 17 1 2 3 4 5 6 21 22 23 24 25 26 27 28 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 TX PARKING LIGHT (-) REMOTE STARTER STEERING LOCK 7 6 5 4 3 2 1 PARKING LIGHT (-) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT LIFTGATE (-) OUTPUT <- OPTIONAL UNLOCK/DISARM (-) OUTPUT LOCK/ARM (-) OUTPUT GROUND (-) GROUND WHEN RUNNING (-) OUTPUT 7.5 AMPS INPUT IGNITION (+) INPUT BRAKE (+) INPUT HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT 1 2 3 4 5 6 7 8 IGNITION (+) DIODE 1N4001 SLP (-) N/A LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE GROUND (-) - BLACK - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK LIFTGATE (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW RX - PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE 9 10 11 12 13 14 15 16 CANL CANH WHITE/BLACK - SLP (-) OUTPUT WHITE/RED (NC) WHITE - GROUND (-) INPUT YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK - GROUND (-) INPUT ORANGE/WHITE - TX ORANGE - BRAKE (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED - GROUND (-) INPUT BLUE/YELLOW - (-) OUTPUT GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) WITHOUT OEM HOOD SWITCH ONLY CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED IMPORTANT: 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. ENGINE START STOP 8 9 10 11 12 13 14 1 2 3 4 5 6 7 (-)
Page 6 of 11 OL-AL(MDB)-TL2-EN Doc. No.: ##28069## 20160407 TYPE 2 - CROSS REFERENCE CHART - 1 OF 1 MAKE MODEL YEAR LEXUS DESCRIPTION NAME TYPE POSITION TOYOTA POLARITY MODULE LOCATION COMPONENT LOCATOR GX460 RX350 RX450h 4Runner Sienna 10-15 10-15 10-15 10-16 11-16 CanH G37 White 16 pin 06 Red (DATA) OBDII D CanL G37 White 16 pin 14 White (DATA) OBDII D 12V G23 Black 07 pin 07 Green (+) Steering lock B Ignition G23 Black 07 pin 06 White (+) Steering lock B SLP G23 Black 07 pin 04 LtBlue (-) Steering lock B TX G47 White 30 pin 16 Green (DATA) Main body ECU A RX G47 White 30 pin 04 Red (DATA) Main body ECU A Parking Light G47 White 30 pin 30 White (-) Main body ECU A G24 Black 14 pin 07 LtGreen (-) Push to start button C CanH F17 ~ 16 pin 06 Purple (DATA) OBDII D CanL F17 ~ 16 pin 14 Red (DATA) OBDII D 12V F37 Black 07 pin 07 Blue (+) Steering lock B Ignition F37 Black 07 pin 06 Black (+) Steering lock B SLP F37 Black 07 pin 04 Green (-) Steering lock B TX F14 ~ 30 pin 16 LtGreen (DATA) Main body ECU A RX F14 ~ 30 pin 04 Pink (DATA) Main body ECU A Parking Light F14 ~ 30 pin 30 Purple (-) Main body ECU A F22 ~ 14 pin 07 LtGreen (-) Push to start button C CanH F17 ~ 16 pin 06 Purple (DATA) OBDII D CanL F17 ~ 16 pin 14 Red (DATA) OBDII D 12V F37 Black 07 pin 07 Blue (+) Steering lock B Ignition F37 Black 07 pin 06 Black (+) Steering lock B SLP F37 Black 07 pin 04 Green (-) Steering lock B TX F14 ~ 30 pin 16 LtGreen (DATA) Main body ECU A RX F14 ~ 30 pin 04 Pink (DATA) Main body ECU A Parking Light F14 ~ 30 pin 30 Purple (-) Main body ECU A F22 ~ 14 pin 07 LtGreen (-) Push to start button C CanH F13 ~ 16 pin 06 Purple (DATA) OBDII D CanL F13 ~ 16 pin 14 White (DATA) OBDII D 12V F68 Black 07 pin 07 Gray (+) Steering lock B Ignition F68 Black 07 pin 06 White (+) Steering lock B SLP F68 Black 07 pin 04 LtBlue (-) Steering lock B TX F10 ~ 30 pin 16 White (DATA) Main body ECU A RX F10 ~ 30 pin 04 Gray (DATA) Main body ECU A Parking Light F10 ~ 30 pin 30 Red (-) Main body ECU A F71 ~ 14 pin 07 LtGreen (-) Push to start button C CanH D16 ~ 16 pin 06 Red (DATA) OBDII D CanL D16 ~ 16 pin 14 White (DATA) OBDII D 12V D29 Black 07 pin 07 Red (+) Steering lock B Ignition D29 Black 07 pin 06 Black (+) Steering lock B SLP D29 Black 07 pin 04 Green (-) Steering lock B TX D13 ~ 30 pin 16 Blue (DATA) Main body ECU A RX D13 ~ 30 pin 04 Black (DATA) Main body ECU A Parking Light D13 ~ 30 pin 30 Yellow (-) Main body ECU A D33 ~ 14 pin 07 LtBlue (-) Push to start button C
Page 7 of 11 OL-AL(MDB)-TL2-EN Doc. No.: ##28069## 20160407 TYPE 2 - WIRING DIAGRAM RX TX MAIN BODY ECU WARNING: DO NOT CONNECT ANY OTHER ACCESSORY,IGNITION OR START FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLING THE REQUIRED VEHICLE POWER AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. 19 20 21 7 8 9 1 2 3 22 23 24 10 11 12 25 26 27 13 14 15 28 29 30 16 17 18 4 5 6 PARKING LIGHT (-) PARKING LIGHT (-) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT LEFT SLIDING DOOR (-) OUTPUT <- OPTIONAL RIGHT SLIDING DOOR (-) OUTPUT <- OPTIONAL POWER LIFTGATE (-) OUTPUT <- OPTIONAL UNLOCK/DISARM (-) OUTPUT LOCK/ARM (-) OUTPUT GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REMOTE STARTER INPUT IGNITION (+) INPUT BRAKE (+) INPUT HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT STEERING LOCK 7.5 AMPS 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 SLP (-) IGNITION (+) DIODE 1N4001 N/A LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE 9 10 11 12 13 14 15 16 CANL CANH GWR (-) INPUT - BLUE/WHITE GROUND (-) - BLACK - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK LIFTGATE (-) INPUT - RED/WHITE RIGHT SLIDING DOOR (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RX - PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - SLP (-) OUTPUT WHITE/RED (NC) WHITE - GROUND (-) INPUT YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK - GROUND (-) INPUT ORANGE/WHITE - TX ORANGE - BRAKE (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED - GROUND (-) INPUT BLUE/YELLOW - (-) OUTPUT GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) WITHOUT OEM HOOD SWITCH ONLY CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED IMPORTANT: 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. ENGINE START STOP 8 9 10 11 12 13 14 1 2 3 4 5 6 7 (-)
Page 8 of 11 OL-AL(MDB)-TL2-EN Doc. No.: ##28069## 20160407 TYPE 3 - CROSS REFERENCE CHART - 1 OF 1 MAKE MODEL YEAR LEXUS DESCRIPTION NAME TYPE TOYOTA POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR CT200h HS250h Prius Prius V 11-15 10-12 10-15 12-16 CanH ~ ~ 16 pin 06 Red (DATA) OBDII D CanL ~ ~ 16 pin 14 White (DATA) OBDII D 12V ~ ~ 01 pin 01 White (+) Main body ECU A Ignition ~ ~ 40 pin 02 Red (+) Main body ECU A TX ~ ~ 30 pin 16 LtBlue (DATA) Main body ECU A RX ~ ~ 30 pin 04 Yellow (DATA) Main body ECU A Parking Light ~ ~ 30 pin 30 Yellow (-) Main body ECU A ~ ~ 14 pin 07 Black (-) Push to start button C CanH F11 ~ 16 pin 06 Green (DATA) OBDII D CanL F11 ~ 16 pin 14 Black (DATA) OBDII D 12V 2E ~ 01 pin 01 White (+) Main body ECU A Ignition 2C ~ 40 pin 02 White (+) Main body ECU A TX F9 ~ 30 pin 16 Blue (DATA) Main body ECU A RX F9 ~ 30 pin 04 Yellow (DATA) Main body ECU A Parking Light F9 ~ 30 pin 30 White/Black (-) Main body ECU A F2 ~ 14 pin 07 Blue (-) Push to start button C CanH L61 ~ 16 pin 06 White (DATA) OBDII D CanL L61 ~ 16 pin 14 Yellow (DATA) OBDII D 12V 2E ~ 01 pin 01 White (+) Main body ECU A Ignition 2C ~ 40 pin 02 Red (+) Main body ECU A TX L7 ~ 30 pin 16 Green (DATA) Main body ECU A RX L7 ~ 30 pin 04 Purple (DATA) Main body ECU A Parking Light L7 ~ 30 pin 30 Yellow (-) Main body ECU A L43 ~ 14 pin 07 Black (-) Push to start button C CanH L61 ~ 16 pin 06 Black (DATA) OBDII D CanL L61 ~ 16 pin 14 White (DATA) OBDII D 12V 2E ~ 01 pin 01 White (+) Main body ECU A Ignition 2C ~ 40 pin 02 Red (+) Main body ECU A TX L7 ~ 30 pin 16 Green (DATA) Main body ECU A RX L7 ~ 30 pin 04 Purple (DATA) Main body ECU A Parking Light L7 ~ 30 pin 30 Yellow (-) Main body ECU A L43 ~ 14 pin 07 Black (-) Push to start button C
Page 9 of 11 OL-AL(MDB)-TL2-EN Doc. No.: ##28069## 20160407 TYPE 3 - WIRING DIAGRAM WARNING: DO NOT CONNECT ANY OTHER ACCESSORY,IGNITION OR START FROM THE REMOTE STARTER TO THE VEHICLE. THE INTERFACE MODULE IS HANDLING THE REQUIRED VEHICLE POWER AND START SEQUENCE FROM THE PUSH TO START BUTTON CIRCUIT. 19 20 21 7 8 9 1 2 3 RX 22 23 24 10 11 12 TX 25 26 27 13 14 15 28 29 30 16 17 18 4 5 6 PARKING LIGHT (-) MAIN BODY ECU REMOTE STARTER 10 9 8 7 6 5 25 24 23 22 21 20 19 18 17 40 39 38 37 36 35 34 33 32 4 3 2 1 16 15 14 13 12 11 31 30 29 28 27 26 PARKING LIGHT (-) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT TRUNK/LIFTGATE (-) OUTPUT <- OPTIONAL UNLOCK/DISARM (-) OUTPUT LOCK/ARM (-) OUTPUT GROUND (-) GROUND WHEN RUNNING (-) OUTPUT 7.5 AMPS INPUT IGNITION (+) INPUT BRAKE (+) INPUT HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT 1 IGNITION (+) DIODE 1N4001 1 2 3 4 5 6 7 8 N/A LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE 9 10 11 12 13 14 15 16 CANL CANH GWR (-) INPUT - BLUE/WHITE GROUND (-) - BLACK - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK/LIFTGATE (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW RX - PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK - GROUND (-) INPUT ORANGE/WHITE - TX ORANGE - BRAKE (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED - GROUND (-) INPUT BLUE/YELLOW - (-) OUTPUT GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) WITHOUT OEM HOOD SWITCH ONLY CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED IMPORTANT: 1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. 2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE. ENGINE START STOP 8 9 10 11 12 13 14 1 2 3 4 5 6 7 (-)
Page 10 of 11 OL-AL(MDB)-TL2-EN Doc. No.: ##28069## 20160407 INSTALLATION MODE SELECTION 1 Press and release programming button to select installation mode. LED flashes (1X) once = LED flashes (2X) twice = STANDARD HARD MODE 2! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PROGRAMMING PROCEDURE NOTE I 1 Between each step, LED will turn solid RED, this is the default standby mode. Æ x2 ENGINE START STOP Push start button twice [2x] to ON position. 3 4 Æ x1 ENGINE START STOP Push start button once [1x] to OFF position. Module Programming Procedure completed. 2 Wait, LED will turn solid GREEN then will turn OFF.
XX-XX PATENT INSTALL GUIDE PAGE X-X Page 11 of 11 OL-AL(MDB)-TL2-EN Doc. No.: ##28069## 20160407 IDENTIFY VEHICLE NOTICE YEAR 1 Locate the Vehicle Identification Number (VIN), identify the 10th character then match it to its corresponding year. Æ 4 3 A 5 Y 1 N 5 T A L 8 D 5 R 0 X Æ A 1980 L 1990 Y 2000 A 2010 B 1981 M 1991 1 2001 B 2011 C 1982 N 1992 2 2002 C 2012 D 1983 P 1993 3 2003 D 2013 E 1984 R 1994 4 2004 E 2014 F 1985 S 1995 5 2005 F 2015 G 1986 T 1996 6 2006 G 2016 H 1987 V 1997 7 2007 H 2017 J 1988 W 1998 8 2008 J 2018 K 1989 X 1999 9 2009 K 2019 LED STATUS Flashing RED DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE 1 2 DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for 2 seconds. RESET COMPLETED. RECONNECT all connectors. 3 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 4 When LED flashes red, RELEASE programming button. This product is protected by one or more of the following patents: U.S. LETTERS PATENT NO. 5,719,551; 6,011,460; 6,243,004; 6,249,216; 6,275,147; 6,297,731; 6,346,876; 6,392,534; 6,529,124; 6,696,927; 6,756,885; 6,756,886; 6,771,167; 6,812,829; 6,924,750; 7,010,402; 7,031,826; 7,046,126; 7,061,137; 7,068,153; 7,015,830; 7,205,679; 7,224,083; 7,369,936; 7,378,945; 7,489,233; 7,501,937; CANADIAN PATENT NO. 2,320,248; 2,415,023; 2,426,670; 2,414,991; 2,415,011; 2,415,027; 2,415,038; 2,415,041; 2,502,893; 2,451,490; 2,452,296; 2,451,487; EUROPEAN PATENT NO. 1,053,128; DE 69807-941T2; U.S. 20020145535; 20060129282; 20060129284; 20040017284; 20080030316; 20090079552; EP1500565; 1538038; 1538037;