LOW MOTOR S MT BP SPRING LOADED BACK PRESS. w/reduced INNER APPLICATIONS: Liquid or gas systems where a 0 to psig adjustable back pressure is desired, such as treaters, free water knockouts, pressure vessels, vent lines on separators, flow treaters, compressor stations, and gas gathering systems. FEATURES: Single adjustment Single soft seat Removable valve seat Internal sense line Minimum maintenance All internal parts can be removed with valve in line Spring adjustment 0 to 0 psig. 0 to 0 psig. 0 to 0 psig. 0 to 6 psig. 6 to 90 psig. to psig. Adjusting Screw CERTIFICATIONS: Canadian Registration Number (CRN): 0C676.67890NTY (Ductile) 0C.67890NTY (Steel) CONSTRUCTION: Body and housings are available in cast iron, ductile iron or steel. Valve stem is 0 stainless steel. Spring is stainless steel. Diaphragm and seating materials are oil resistant synthetic rubber or polyurethane. After assembly each valve is given a complete operational test. OPERATION: The Stem Assembly is the only moving unit in the motor valve. The PRELOAD SPRING loads the Stem Assembly and is opposed by Upstream Pressure (Green) on the under side of the DIAPHRAGM plus the differential of Upstream Pressure (Green) minus Downstream Pressure (Blue) across the INNER SEAT. An increase in Upstream Pressure (Green) exceeding the set pressure of the PRELOAD SPRING moves the Stem Assembly upward, opening the INNER SEAT. A decrease in Upstream Pressure (Green) decreases the force on the INNER SEAT and DIAPHRAGM allowing the PRELOAD SPRING to move the Stem Assembly downward reducing the flow from Upstream Pressure (Green) to Downstream Pressure (Blue). The interaction between the PRELOAD SPRING and the Upstream Pressure (Green) on the INNER SEAT and the DIAPHRAGM will cause the valve to open or close the amount required to maintain the Upstream Pressure (Green) set by the ADJUSTING SCREW. Cf & Cv VALUES Line Size Trim Size Cf Cv ".0" 0.86.6 "." 0.8.0 ".6" 0.8. Preload Spring Stem Assembly Upstream Pressure Downstream Pressure Diaphragm Oil Inner Valve Seat Add Certifications Kimray is an ISO 900- certified manufacturer. E:. Issued /6
LOW MOTOR S MT BP SPRING LOADED BACK PRESS. w/reduced INNER DUCTILE IRON 69, Adjusting Screw 76, Upper Spring Guide 888 Bonnet Stem Upper Diaphragm Plate Screw Nut 897 0, " 8, " 0, " 8, " 77, " 7, " 96, 8 Req d. " 907, 0 Req d. " Housing, " 6, " 68 (0 lbs.) Silver, " ( lbs.) Blue, " 6 (0 lbs.) Green, " Spring 0 (6 lbs.) Yellow, " 7 (90 lbs.) Orange, " 006 & 676 ( lbs.) Red, " 006 (0 lbs.) Red, " Lock Nut 7, "* 906, " Lower Spring Guide Diaphragm 09, " 9, " 69, "* 7, " Lower Diaphragm Plate SS6, " 78, " O Ring Q, "*, " *Gasket 96, " 97, " Seat Disc, " 9, " *Back Up 9T to 0T, Req d. Oil *Seat 0P, " 0P, " Removable Seat 00, " 9D, " Gasket 76, " 77, " Ratio Plug 9 Body Lock Nut 7* Line Size " " Screwed 9 6 Flanged 9 9 Grooved 96 -- Removable Seat Wrench 6SW, " 9SW, " THRU S AVAILABLE: NOTES: CAT. SIZE MOTOR OPER MAX. NO. TYPE S PRESS W.P. KIT ALU ". 0 SMT BP-D 0-0 00 RTB ALU ". 0 SMT BP-D 0-0 00 RTB ALU ". 0 SMT BP-D 0-0 00 RTB ALU6 ". 06 SMT BP-D 0-6 00 RTB ALU9 ". 09 SMT BP-D 6-90 00 RTB ALU ". SMT BP-D - 00 RTB ALV " GRVD. 0 GMT BP-D 0-0 00 RTB ALV " GRVD. 0 GMT BP-D 0-0 00 RTB ALV " GRVD. 0 GMT BP-D 0-0 00 RTB ALV6 " GRVD. 06 GMT BP-D 0-6 00 RTB ALV9 " GRVD. 09 GMT BP-D 6-90 00 RTB E:. Issued /8 CAT. SIZE MOTOR OPER MAX. NO. TYPE S PRESS W.P. KIT ALV " GRVD. GMT BP-D - 00 RTB ALW " FLGD. 0 FMT BP-D 0-0 0 RTB ALW " FLGD. 0 FMT BP-D 0-0 0 RTB ALW " FLGD. 0 FMT BP-D 0-0 0 RTB ALW6 " FLGD. 06 FMT BP-D 0-6 0 RTB ALW9 " FLGD. 09 FMT BP-D 6-90 0 RTB ALW " FLGD. FMT BP-D - 0 RTB ENQ ". 0 SMT BP-D 0-0 7 RTD ENR " FLGD. 0 FMT BP-D 0-0 7 RTD *These are recommended spare parts and are stocked as repair kits. For dimensions refer to Table of Contents. Kimray is an ISO 900- certified manufacturer. Add inch valves
LOW MOTOR S LIQUID CAPACITY CHART CAPACITY - Blds. Water/Day, Steady Row SINGLE ACTING MOTOR S SIZE-INCHES 6 0 0 0 0 0 00 0 0 0 0 0 6 7 6 87 9,0, 7,0,00,00,0,00,900,00,00,0,00,0 6,00 6,0 7,00 8,00,7,00,00,00,900,0 6,0 7,900 9,0,00,00,0,0,0 7,0 9,0,0,900 6,00 7,000 7,0,000,00,0 9,00,00,0 7,00 9,00,00,00 8,00 7,0,000,00,0 7,00,0 0,00,900,0 9,00,00,00 6,00 69,0 78,00 87,00 WITH REDUCED INNER S SIZE-INCHES 0 0 0 0 0 00 6 7 9 8 0 6 6 8 00 0 0 90 90 0 0 90 6 900,0,90,0,,0,,0,,90, 7 89,0,0,,000,0,,,,000,00,0,0, 8,,,,90,,,900,0,00 6,00 6, 7,00 7,0 8,0 9,0 6,90,,,900,7 6,7 7,0 8,7 0,67,00,0,00 6,0 7,0 9,00,900 For gravity correction, multiply the above figures by Where G is the specific gravity of the flowing liquid. G Change Logo E:0. Issued /
LOW MOTOR S LIQUID CAPACITY CHART CAPACITY - Blds. Water/Day, Steady Row 0 0 0 0 0 00 DOUBLE ACTING MOTOR S 0 7 90,,,,0,,8,0,,,00,0 SIZE-INCHES 6,0,0,,00,00,0,8 6,0 8,0 9,0 0,,7,0,0,00 6,900,0,,0 6,00 7,00 9,9,00,00 7,00 9,900,00,00 6,00 8,00,00,00, 8,0 0,0,0,00 8,00,0 6,00,900 6,900,00,00 8,0,00 8,00 6,00,0 8,0,0 6,00 9,00,0 0,900 8,0 7,000 8,00 9,000 0,000 0,000 7,00,00 7,000 0 0 0 0 0 00 WITH REDUCED INNER S 0 7 00 0 90 0 7 8 90,00,0 SIZE-INCHES,00,,7,,0,87,00,00,,00,0 6,0 6,0 7,7 8,00,0,,8,0,00,00,0,0,900 6,0 7,0 8,0 9,000 9, 0,0,000,,0,8,00,0,0 6,00 7,00 9,00 0,00,0,0,0,0 6,00 8,0 6,,0 6,0 7,0 8,00,90,0 6, 0,0,0 6,0 9,00,00,0 7,00,000 ADJUSTABLE DOUBLE ACTING WITH REDUCED INNER S ADAB 0 7 00 0 0 90 0 0 0 0 0 7 8 90 00,00,0 For gravity correction, multiply the above figures by Where G is the specific gravity of the flowing liquid. G E:0. Issued / Change Logo
LOW MOTOR S DIMENSIONS MT (SINGLE ACTING MOTOR ) MT- (WITH REDUCED INNER S) MT-DA, MT-DA (DOUBLE ACTING MOTOR ) MT-DA, MT-DA (WITH REDUCED INNER S) MT-DA (DOUBLE ACTING MOTOR ) MT-DA (WITH REDUCED INNER S) MT-ADA, MT ADAB (ADJUSTABLE DOUBLE ACTING) MT BP, MT BP (SPRING LOADED BACK ) LINE SIZE BODY STYLE " " FLGD GRVD " FLGD " FLGD 6" FLGD A B C D E F G H /8 /8 / /8 /8 /8 8 8 / /8 /8 7/8 6 7/8 6 7/8 8 / 9 /8 7/8 6 7/8 6 7/8 8 / 8 / /8 /8 7/8 6 7/8 6 7/8 8 / /6 7/8 8 8 8 0 /6 / 7/8 8 8 8 0 7 / 9 / 9 / 9 / /8 / 7 / 9 / 9 / 9 / /8 / 6 / FLANGE DIMENSIONS ARE ASA 0 LB. STANDARD. Add "H" dimension to inch E:0. Issued /8