On-load tap-changers, types UCG, UCL, UCC and UCD with motor-drive mechanisms, types BUE and BUL Spare Parts List ZSE 5492-33 en, Rev. 3, 2004-04-5
This document must not be copied without our written permission, and the contents thereof must not be imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted.
Before You Order Check the identification of the on-load tap-changer. The type and serial number are always required for identification. Check this data on the rating plate on the tapchanger if you are not sure. Do not try to order spares without this information. It is very important that you give a complete identification for each and every part you order to have trouble-free delivery. The lists in this documentation together with the identification as described above give you all information required for correct ordering. WARNING, CAUTION and NOTE WARNING A WARNING provides information which, if disregarded, could cause injury or death. CAUTION A CAUTION provides information which, if disregarded, could cause damage to the equipment. NOTE: A NOTE provides additional information to assist in carrying out the work described. Safety Precautions WARNING This documentation is intended for procurement of spare parts only. Only personnel familiar with repairs of transformers and accessories should carry out replacement of parts. Electrical and other safety regulations at the repair site must be strictly adhered to. iii
Contents Introduction 7. Type Designation and Serial Number 7.2 Item Number 7.3 Name of Item 7.4 Quantity 7.5 Remarks 7 2 General Arrangement 8 2. Standard Spare Parts 8 2.2 Special Spare Parts 8 3 Spare Parts for On-Load Tap-Changer 0 3. Type UCG 0 3.2 Type UCL 2 3.3 Types UCC and UCD 4 4 Accessories for On-Load Tap-Changer 6 5 Spare Parts for Motor-Drive Mechanism type BUE 8 5. Electrical Details 8 5.2 Mechanical Details 20 6 Spare Parts for Motor-Drive Mechanism type BUL 24 6. Electrical Details 24 6.2 Multi Position Switches 26 6.3 Mechanical Details 28 7 Recommended Set of Spare Parts for Motor-Drive Mechanisms 30
Introduction Introduction This spare parts list has been compiled to help you with procurement of spares. To obtain trouble-free deliveries you should note a few things which are explained in the following text. The breakdown level and general contents of this list have been worked out to cover normal customer requests. Our spares sales people will be happy to assist if you require any specific item that is not included in the list.. Type Designation and Serial Number The rating plate on the on-load tap-changer (OLTC) shows the type and serial number of the device you are ordering spares for. It is important to have this information, because the manufacture of parts gradually changes as materials and manufacturing technology improves. ABB makes every effort to supply spares that should fit your requirements. Some parts of later manufacture than those you are replacing may need some adaptation to fit into your device. Our spare parts sales people need to know the type designation and serial number to supply exactly what you require..2 Item Number Item numbers are shown on the drawings and lists. As you will observe, one item number is used for several items of the same general type. These items have a specific specification for each and every variant of OLTC, hence you need to specify type and serial number in addition to the item number to obtain the appropriate spare..3 Name of item The name should be specified when ordering to make sure the right type of item is ordered..4 Quantity The figures given represent the number of items that are fitted to one OLTC..5 Remarks Information pertinent to different variants of the OLTC is given in this column. Your model should be one of those shown. 7
2 General Arrangement 2 General Arrangement The general arrangement of an UC type on-load tap-changer is shown in fig.. 2. Standard Spare Parts The rugged design of ABB OLTCs means that only the fixed and moving contacts of the diverter switch might require replacement during lifetime of the transformer. This spare parts list tells you the part number of the contacts when ordering for your replacement requirements. 2.2 Special Spare Parts If you need parts other than the contacts in the lists, our staff will be happy to assist you. Please use fig. as a reference when discussing your requirements. As usual, the type designation and serial number are essential for ordering. 8
2 General Arrangement Diverter switch housing Cover Oil valve Bevel gear Pressure relay Position indicator Serial No. Earthing terminal Connection flange for gas operated relay Insulating shaft Shielding-ring ) Shielding-ring 2) Transition resistors Top-section Shielding-ring ) Draining tube Insulating cylinder Diverter switch Plug-in contacts Fixed and moving contacts Serial No. Guide-pins Bottom section Current terminal Driving disc for the diverter switch Tap selector Bottom valve for drying process Intermediate gear Geneva gear ) Only at impulse withstand voltage to earth of 650 kv and 050 kv 2) Not on UCG of the short type Change-over selector Moving fineselector contacts Current collector Fixed fine-selector contacts Fig.. General arrangement of on-load tap-changer, type UC. 9
3 Spare Parts for On-Load Tap-Changer 3 Spare Parts for On-Load Tap-Changer 3. Type UCG Item No. Name of item Quantity Remarks set UCG.E.../300 UCG.E.../500 3 sets UCG.T.../300 UCG.T.../500 3 sets UCGYD.../300 UCGYD.../500 set UCG.E.../600 3 sets UCG.T.../600 3 sets UCGYD.../600 set UCG.N.../300 set UCG.N.../500 set UCG.E.../200 3 sets UCG.T.../200 3 sets UCGYD.../200 set UCG.N.../600 set UCG.E.../500 3 sets UCG.T.../500 3 sets UCGYD.../500 Complete diverter switch Complete tap selector 0
3 Spare Parts for On-Load Tap-Changer Fig. 2. Diverter switch for UCG with replacement contacts. NOTE: This picture shows a neutral point type. Single phase types have not always contacts in all the three poles of the diverter switch.
3 Spare Parts for On-Load Tap-Changer 3.2 Type UCL Item No. Name of item Quantity Remarks set 3 sets UCL.E.../600, UCL.E.../900 When the step voltage is outside the envelope for the 900 A type 3 sets UCL.E.../800, UCL.E.../2400 3 sets UCL.N.../600, UCL.N.../900 3 sets 9 sets UCL.T.../600, UCL.T.../900 When the step voltage is outside the envelope for the 900 A type 9 sets UCL.T.../800, UCL.T.../2400 3 sets UCL.B.../600, UCL.B.../900 Complete diverter switch Complete tap selector 2
3 Spare Parts for On-Load Tap-Changer Fig. 3. Diverter switch for UCL with replacement contacts. 3
3 Spare Parts for On-Load Tap-Changer 3.3 Types UCC and UCD Item No. Name of item Quantity Remarks set UCC.N.../800 UCC.N.../200 UCC.N.../600 UCC.E.../3600 UCC.E.../4500 Complete diverter switch Complete tap selector UCD.N.../000 UCD.E.../2400 4
3 Spare Parts for On-Load Tap-Changer Fig. 4. Diverter switch for UCC and UCD with replacement contacts. 5
4 Accessories for On-Load Tap-Changer 4 Accessories for On-Load Tap-Changer Item No. Name of item Quantity Remarks 2 3 4 5 6 7 Pressure relay Pressure relay with test valve Pressure relief valve Oil valve Vent Cover for connection to oil conservator Bottom valve key 6
4 Accessories for On-Load Tap-Changer 3 fm_00283 Fig. 5. Accessories (The figure shows type UCG). 7
5 Spare Parts for Motor-Drive Mechanism type BUE 5 Spare Parts for Motor-Drive Mechanism type BUE Item No. Name of item Quantity Remarks Complete motor-drive mechanism with cabinet 5. Electrical Details Item No. Name of item Quantity Remarks Control selector switch 2 Control switch raise/lower 3 Motor contactor Raise 4 Motor contactor Lower 5 Starting contact 6 Maintaining contact 7 Motor 8 Limit switch Interlocking switch 2 Heater 50 W 4 Position transmitter 5 Continuation contact 9 Motor-protective switch 2 Step-by-step contactor 26 Terminal blocks 27 Heater 00 W 28 Thermostat 29 Switch for heater 3 Tap-changer for current transformer 33 Tap-changer for voltage transformer 36 Lamp for cabinet light 37 Door-operated switch 83 Master switch 84 Follower switch 86 Odd-even switch 8
5 Spare Parts for Motor-Drive Mechanism type BUE fm_0036 Fig. 6. Electrical details. 9
5 Spare Parts for Motor-Drive Mechanism type BUE 5.2 Mechanical Details Item No. Name of item Quantity Remarks 0 Toothed belt 02 Conical toothed wheel 03 Outgoing shaft 04 Hand crank 05 Operating shaft 06 Gear 07 One turn shaft 08 Geneva drive with shaft 09 Conical toothed wheel 0 2 2 3 Hand for position indication Coupling Geneva drive with shaft Geneva drive with shaft End stop, cam disc + for each cont. plate For pot. transmitter For other cont. device 4 Shear pin 5 Cam disc 6 Arm 7 Brake 8 Brake disc 9 Front plate 20 Operation counter 2 Pulley 22 Pulley 23 Conical toothed wheel 24 Cylindrical toothed wheel 25 26 27 28 Geneva wheel Geneva wheel with arm Contact guide device Cam bar For double contact 29 Brake for maintaining contact (item No. 6) 30 Cam disc for starting contact (item No. 5) 3 Driving disc for item No. 30 36 Screw for end stop 20
5 Spare Parts for Motor-Drive Mechanism type BUE fm_0037 Fig. 7. Mechanical details. 2
5 Spare Parts for Motor-Drive Mechanism type BUE Item No. Name of item Quantity Remarks 32 32 33 33 Cabinet Cabinet Gasket for door Gasket for door For BUE For BUE 2 For BUE For BUE 2 34 Hand knob 35 Air vent 40 Cover 4 Gasket 42 Vibration damper 4 43 Coupling 45 Shaft for maintaining contact (item No. 6) 46 Shaft for starting contact (item No. 5) 47b Lever 48 Drive 49 Shaft 50b Toothed wheel 5 Drive 52 Shaft 53 54 Shaft Panel For DAG motor-switch 55 Brake disc 2 56 Spring 2 57 Brake disc 58 Spring 59b Sleeve 60 Nave 6 80 80 Operating wire for operation counter (item No. 20) Door with window Door with window For BUE For BUE 2 22
5 Spare Parts for Motor-Drive Mechanism type BUE 35 43 32 34 33 80 42 46 5 6 56 4 54 40 55 57 58 59b 50b 60 48 49 52 47b fm_00274 53 Fig. 8. Mechanical details (cont.). 23
6 Spare Parts for Motor-Drive Mechanism type BUL 6 Spare Parts for Motor-Drive Mechanism type BUL Item No. Name of item Quantity Remarks Complete motor-drive mechanism with cabinet 6. Electrical Details Item No. Name of item Quantity Remarks B Thermostat ) B2 Hygrostat ) E Anti-condensation heater 50 W E2 E3 K Extra heater Cabinet light, Hand lamp Step-by-step relay 00 W ) ) M Motor Q Motor protective switch Q2 Contactor, Raise Q3 Contactor, Lower S Control selector switch Local-0-Remote S2 S3+S4 S5 Control switch Maintaining, interlocking and auxiliary contacts Interlocking switch Lower-0-Raise Raise and lower, assembled on a mounting plate For handcrank S6 Limit switch, Upper tap position Including mounting plate with arm and roller S7 S9 S0 Limit switch, Lower tap position Door operated switch Switch for extra heater Including mounting plate with arm and roller ) U Measuring amplifier X-7 Terminal blocks X38 Outlet ) When ordering, it must be stated for this optional item, if it was already installed in the motordrive mechanism. If it is not the case, other assembly details will be included in the order. 24
6 Spare Parts for Motor-Drive Mechanism type BUL S6 S7 B2 S3 + S4 B S0 M X38 S5 K X-7 U S2 S E2 Q3 Q2 Q E E3 S9 fm_00246 Fig. 9. Electrical details, type BUL. 25
6 Spare Parts for Motor-Drive Mechanism type BUL 6.2 Multi Position Switches Item No. Name of item Quantity Remarks S4, S24 S5 S20-S23 S25-S28 S86, S87 Position transmitter, potentiometer Continuation contact Auxiliary contacts, break before make Auxiliary contacts, make before break Step switch for parallel control..2 2 64 65 66 Coupling half Torque disc Shaft Transparent cover Distance screw Terminal, plug part <3 circuit cards 4 5 circuit cards L=0, L=20, L=35 or L=60 4-pole, 8-pole 26
6 Spare Parts for Motor-Drive Mechanism type BUL..2. 2 64 65 S4 (S24) S5 S20 (S2, S22, S23) S25 (S26, S27, S28) S86 (S87) 66 fm_00247 Fig. 0. Multi Position Switches, type BUL. 27
6 Spare Parts for Motor-Drive Mechanism type BUL 6.3 Mechanical Details Item No. Name of item Quantity Remarks 0 04 0 Toothed belt Hand crank Pointer with drag hands for position indicator 20 2 3 Operation counter Pulley for toothed belt Hinges 2 Arm included Key, screw, washer included Screws, washers, shims included 32 34 35 67 68 70 7 80 Cabinet Handknob with fasteners Air vent Gasket for cabinet Thread bushing with nuts Blank, FL 2 Gasket, FL 2 Door with window 2 2 4+8 Screws, washers, shims included 28
6 Spare Parts for Motor-Drive Mechanism type BUL 68 3 80 32 34 67 04 35 7 70 0 20 2 0 fm_00248 Fig.. Mechanical details, type BUL. 29
7 Recommended Set of Spare Parts 7 Recommended Set of Spare Parts for Motor-Drive Mechanisms One set consists of the following parts: For type BUE: Item 3, pages 4 and 5 Motor contactor, raise Item 4, pages 4 and 5 Motor contactor, lower Item 7, pages 4 and 5 Motor Item 9, pages 4 and 5 Motor-protective switch Item 0, pages 6 and 7 Toothed belt For type BUL: Item Q2, pages 9 and 20 Motor contactor, raise Item Q3, pages 9 and 20 Motor contactor, lower Item M, pages 9 and 20 Motor Item Q, pages 9 and 20 Motor-protective switch Item 0, pages 25 and 26 Toothed belt 30
ABB Power Technologies AB Components Visiting address: Lyviksvägen 0 Postal address: SE-77 80 Ludvika, SWEDEN Tel.+46 240 78 20 00 Fax +46 240 2 57 E-mail: sales@se.abb.com www.abb.com/electricalcomponents ZSE 5492-33 en, Rev. 3, 2004-04-5