PRODUCT GUIDE RSB-DC2 DOCUMENT NUMBER REVISION DATE 25 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
GETTING ED PAGE 2 OF 2 25 WELCOME Congratulations on the purchase of your RSB- DC2 solution. You are now a few simple steps away from enjoying your new remote starter unit with enhanced features. Before starting your installation, please ensure that your RSB-DC2 module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TABLE OF CONTENTS Box Contents 3 Tach Programming Procedure 4 Remote Programming Procedure 5 Valet Mode Programming Procedure 6 Compatible Accessories 7 Online Module Settings 9 Module Diagnostics 0 Remote Starter Error Codes Module Reset Procedure 2 NEED HELP? 866 427-2999 support@idatalink.com idatalink.com/support www.2voltdata.com/forum www.facebook.com/groups/idatatech RSB-DC2
BOX CONTENTS - OF PAE 3 OF 2 25 B AUTOMATIC TRANSMISSION CUT LOOP M2-2 PIN BLACK M3-0 PIN WHITE DRONE - 4 PIN GRAY RF PORT - 4 PIN BLUE M5-6 PIN BLUE M4-20 PIN BLACK 2 PIN WHITE - LED 2 PIN BLUE - THERMISTOR PROGRAMMING BUTTON 2 4 3 6 5 8 7 0 9 2 M2 0 GREEN BLACK DOT - LOCK (-) OUTPUT BLUE BLACK DOT - UNLOCK (-) OUTPUT RED/WHITE BLACK DOT - TRUNK RELEASE (-) OUTPUT EMPTY EMPTY BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 BROWN BLACK DOT - SIREN (+) OUTPUT 08 EMPTY 09 PURPLE/BLACK BLACK DOT - RAP SHUTDOWN (-) OUTPUT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT - GROUND WHEN ARMED (-) OUTPUT 2 WHITE BLACK DOT - PARKING LIGHTS (-) OUTPUT LED 2 FT-DAS - 4 PIN RED FT-DAS SENSITIVTY ADJUSTMENT DIAL WEBLINK PORT - 4 PIN BLACK -WAY REMOTE TEMPERATURE SENSOR LED ANTENNA 2 4 6 8 0 3 5 7 9 M3 0 BROWN SILVER DOT - BRAKE (+) INPUT BLACK/WHITE SILVER DOT - E-BRAKE (-) INPUT PURPLE SILVER DOT - DOOR (+) INPUT GREEN SILVER DOT - DOOR (-) INPUT EMPTY WHITE/BLUE SILVER DOT - X-TRIGGER (-) INPUT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT - TRUNK (-) INPUT 09 EMPTY 0 TAN SILVER DOT - EXT ALARM SENSOR (-) INPUT M4 X RF PORT - 4 PIN BLACK 2 4 3 6 5 8 7 0 9 2 4 3 6 5 8 7 20 9 FUNCTIONS DEFINED BY FIRMWARE STICKERS HOOD SWITCH ANTENNA CABLE 2X M5 3 5 2 4 6 FUNCTIONS DEFINED BY FIRMWARE RSB-DC2
!" # $ % $ PAGE 4 OF 2 25 0 OFF ACC ON vehicle for 5 seconds. S SOP Press and hold the brake pedal. Press and release the module s programming button. (OR if the remotes are already programmed to the vehicle, press and hold the start button of the remote for 2.5 seconds.) Wait, LED 2 will flash GREEN. (See the Module Diagnostics page) Release the brake pedal. Module Programming Procedure completed. RSB-DC2
&'()*+&*,)( *)+-().*-/*&++0/.*-2)34*) 5 6 -' 6 PAGE 5 OF 2 25 >> WARNING: Program aftermarket remotes before usage. A maximum of four [4x] aftermarket remotes per system. Parking Light will flash once [x]. 0 Time restriction. Complete next step within 7 seconds. >> To program additional remotes: repeat steps 4 to 6 using each additional remote. OFF ACC ON Cycle ignition ON ive times [5x OFF/ON] rapidly. 07 Wait, Parking Light will flash twice [2x]. Parking Light will flash once [x]. 08 OFF ACC ON Turn ignition to OFF position. Time restriction. Complete next step within 5 seconds from previous step. 09 Aftermarket Remote Programming Procedure completed. Press once [x] on LOCK button of aftermarket remote. RSB-DC2
V789: ;<=9 >?<@?7;;CD@ >?<F9=G?9 H I <J I PAGE 6 OF 2 25 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Valet Mode Programming Procedure completed. 0 Time restriction. Complete next step within 7 seconds. >> To exit valet mode: repeat steps to 5. OFF ACC ON Cycle ignition ON twice [2x OFF/ON] rapidly. Press and release the BRAKE pedal three times [3x]. Parking Light will flash once [x] then will flash twice [2x]. OFF ACC ON Set ignition to OFF position. RSB-DC2
KLMNOPQRTU OKKUVVLWQUV X Y LZ [ PAGE 7 OF 2 25 WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE WEBLINK MOBILE (accessory sold separately) OBDII CONNECTOR MODULE WEBLINK PORT 4 PIN BLACK CABLE MOBILE DEVICE PORT 2 3 4 5 6 7 8 OBDII CONNECTOR 9 0 2 3 4 5 6 TELEMATIC KIT (accessory sold separately) DRONE MODULE TELEMATIC PORT (NC) RSB-DC2
\]^_`abcde `\\eff]gbef h i ]j i PAGE 8 OF 2 25 kl mno pqrstuvwvx RF KIT MODULE RF PORT ANTENNA ALARM KIT (accessories sold separately) MODULE 2 PIN BLACK 07 BROWN BLACK DOT - SIREN (+) OUTPUT RED BLACK SIREN MODULE 2 PIN WHITE ALARM LED FT-DAS MODULE 4 PIN RED yz{ z}~y}z z } ƒ ˆ Š TEMPERATURE SENSOR MODULE 2 PIN BLUE RSB-DC2
ONLINE MODULE SETTINGS Œ Ž PAGE 9 OF 2 25 WEB PROGRAMMABLE MENUS MENU Remote Starter MENU 2 Doorlock Options MENU 3 Security Options MENU 4 AUX function assignments MENU 5 Programmable outputs (POC) MENU 6 Pulse Timer Output Coniguration (PTO) MENU 7 Input Conigurations MENU 8 Output Conigurations Programming options are avaible through Weblink and Weblink Mobile only. DESCRIPTION RS related coniguration options Convenience feature coniguration options Alarm activation and settings Set transmitter AUX buttons controls Set actions for programmable outputs Set duration for pulse timer outputs (if used) Set inputs for Auto by irmware/data/analog Set outputs for Auto by irmware/data/analog RSB-DC2
MODULE DIAGNOSTICS - OF PAGE 0 OF 2 25 TEST MODULE LED STATUS DIAGNOSTIC I II III IV DURING MODULE PROGRAMMING DURING TACH PROGRAMMING DURING REMOTE WITH IGNITION OFF š Missing/wr œ ž Ÿ œ ž rmwar ehicle. š Modul Ÿ œ ž ehicl œormation. Ÿ t equir Ÿ ªomplet ž «ogramming. Ÿ Modul ªorrectl ogrammed. OFF ªŸ Ÿ ž «ogrammed. ash T ª ogr žž og ashes T ª ogr žž š Ÿa ± š ashes Ÿ ª Ÿected ² š ashes Syst ž al Ÿ ž ³ š ashes T ª Ÿ œ µ Ÿ ª ogr žž equired ¹ š ashes T ª Ÿ œ «ž t Ÿ Ÿ ª ogr žž equired š Modul ªorrectl ogrammed. š Modul ªorrectl ogrammed. Modul ªorrectl ogr žž ational. Ÿ Ÿ ogress. OFF º ««t Ÿ«œ ž emot tarter. š Modul ªorrectl ogr žž ªonnected. š Modul Ÿ ogr žž» Ÿ œ ž ehicl œormation. F ««t Ÿ«œ ž emot tarter. Ÿ Ÿ ogress. OFF Modul Ÿ esÿ œ emot t Ÿ ¼«ªe. Automotiv½ ¾ À ÁÂÃÄÀÅÂÆÇ ÈÆÉÊ Ë ÌÍÎÏ RSB-DC2
ÐÑÒÓTE ER ERROR CODES - OF PAGE OF 2 25 REMOTE ER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash three [3x] times, then will flash [X] number times to indicate an error code. See table. 0 Engine running. Key in ignition at ON position. Door is open. Trunk is open. Foot brake is ON. Hood is open. 07 The reservation is OFF. (Manual transmission only) 08 Tach failure. 09 The vehicle is moving (VSS). 0 System is in Valet Mode. CAN communication failure 2 RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 3 Bypass problem. REMOTE ER SHUTDOWN ERROR CODES: NOTES [Y] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for 2.5 seconds when using a -WAY remote. OR Press once [x] on button 4 when using a 2-WAY remote. The parking lights will flash four [4x] times, then will flash [Y] number times to indicate an error code. See table. 0 Engine tach signal is lost. Emergency brake is lost. Foot brake is ON. Hood is open. Engine RPM limiter is ON. Glow plug timeout error. 07 Vehicle is moving (VSS). 08 N/A 09 N/A 0 Door is open. CAN communication failure during RS sequence. 2 RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 3 Takeover is not allowed. 4 Shutdown error, board overheat protection. RSB-DC2
MODULE RESET PROCEDURE - OF PAGE 2 OF 2 25 >> ÔÕÖ ollowing procedure resets the module programming to the vehicle. It does not reset any settings conigured online. Module RESET completed. 0 Disconnect all connectors from module except the M BLACK 8-pin connector and the M4 BLACK 20-pin connector. 07 Reconnect all connectors. Disconnect the M BLACK 8-pin connector and the M4 BLACK 20-pin connector. 08 Repeat programming procedure. PRESS AND HOLD the module s programming button while connecting the M BLACK 8-pin connector and the M4 BLACK 20-pin connector. >> Failure to follow procedure may result with a DTC or a CHECK error message. Wait, LED will flash RED. RELEASE programming button. LED will turn RED for 2 seconds. RSB-DC2
INSTALL GUIDE 2-2 MAZDA 3 HATCHBACK PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE COM-RSA-MA3-[RSB-DC2] HARDWARE RSB-DC2 ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
T-HARNESS / COMPONENT LOCATOR - OF PAGE 2 OF 8 C BA T00_H 2-2 Mazda 3 Hatchback PTS AT
T-HARNESS / WIRING DIAGRAM - OF PAGE 3 OF 8! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY. THE TAKEOVER FEATURE IS NOT AVAILABLE. THE VEHICLE WILL SHUT DOWN WHEN A DOOR IS OPENED. RELAY VS2 UNIT, UNDER STEERING COLUMN (A) VS : WHITE : VEHICLE HARNESS VS4 VS3 2: WHITE 2 2: VEHICLE HARNESS M2 0 07 08 09 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 2 HORN (-) BLUE - 0 OPTIONAL 8 9 34 2 3 4 5 6 7 CLOCK SPRING (B) PARKING LIGHTS SWITCH, LEFT OF STEERING COLUMN (C) M3 0 07 GRAY SILVER DOT - HOOD STATUS (-) INPUT 08 09 0 GRAY BLUE DOT GRAY/BLACK BLUE DOT GRAY/RED BLUE DOT (SWITCH SIDE) (CONNECTOR SIDE) PARKING LIGHT (-) YELLOW - PARKING LIGHT 2 (-) GREEN - : WHITE 2 3 4 5 6 M4 M5 0 07 08 09 0 2 3 4 5 6 7 8 9 20 0 MS MS2 HOOD SWITCH 2 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE SET THE PROGRAMMING OPTION THROUGH WEBLINK AS FOLLOWS: IN MENU #7 INPUTS CONFIGURATION, FOR 4-HOOD INPUT SOURCE SELECT -ANALOG. 2 T00_H 2-2 Mazda 3 Hatchback PTS AT
HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 8 C BA T00_W 2-2 Mazda 3 Hatchback PTS AT
HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 8! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY. THE TAKEOVER FEATURE IS NOT AVAILABLE. THE VEHICLE WILL SHUT DOWN WHEN A DOOR IS OPENED. KEYLESS (DATA) LTBLUE - 09 : WHITE UNIT, UNDER STEERING COLUMN (A) IGNITION (+) PURPLE - 7 6 5 4 3 2 0 9 8 7 6 5 4 3 2 32 3 30 29 28 27 26 25 24 23 22 2 20 9 8 7 CANH (DATA) WHITE - 07 2: WHITE CANL (DATA) RED - 08 IGNITION (+) LTGREEN - 0 M2 0 GREEN BLACK DOT BLUE BLACK DOT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT GREEN/BLACK BLACK DOT BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 2 (+) YELLOW - 2 GROUND (-) BLACK - 3 ACCESSORY (+) BROWN - 4 PTS (-) LTBLUE - 7 ER (+) GREEN - 23 HORN (-) BLUE - 0 2 0 9 8 7 6 5 4 3 2 24 23 22 2 20 9 8 7 6 5 4 3 8 9 34 2 3 4 5 6 7 2 CLOCK SPRING (B) M3 0 BROWN SILVER DOT BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT PURPLE/WHITE SILVER DOT WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD STATUS (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY PARKING LIGHT (-) YELLOW - PARKING LIGHT 2 (-) GREEN - : WHITE PARKING LIGHTS SWITCH, LEFT OF STEERING COLUMN (C) 2 3 4 5 6 M4 0 EMPTY EMPTY BROWN/RED - CANH BROWN/YELLOW - CANL BLUE/RED BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED - PTS (-) OUTPUT 2 GRAY/YELLOW 3 GREEN/RED - KEYLESS (DATA) 4 ORANGE/WHITE 5 BROWN - ACCESSORY (+) IN/OUT 6 ORANGE/BLACK 7 PINK - IGNITION (+) IN/OUT 8 PURPLE - ER (+) OUTPUT 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) M5 0 GRAY/BLACK BLUE DOT - PARKING LIGHT 2 (-) SWITCH SIDE WHITE/BLACK BLUE DOT - IGNITION (+) GRAY/RED BLUE DOT - PARKING LIGHT 2 (-) CONNECTOR SIDE WHITE/RED BLUE DOT - IGNITION (+) GRAY BLUE DOT - PARKING LIGHT (-) OUTPUT WHITE BLUE DOT T00_W HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE SET THE PROGRAMMING OPTION THROUGH WEBLINK AS FOLLOWS: IN MENU #7 INPUTS CONFIGURATION, FOR 4-HOOD INPUT SOURCE SELECT -ANALOG. 2-2 Mazda 3 Hatchback PTS AT
MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF 8 >> WARNING: All vehicle doors must be closed and locked prior to remote start sequence. Connect module to computer and proceed with extended programming. 2 ACC ON vehicle for 5 seconds. 0 ACC ON Set ignition to ON position. 07 Connect power first. Connect module to vehicle. 3 Press and hold the brake pedal. Wait, LED will turn solid RED to confirm that the ignition is ON. 08 ACC ON Set ignition to ON position. 4 Press and release the module s programming button. Wait 0 seconds, LED will flash GREEN rapidly. 09 Wait, LED will turn solid RED to confirm that the ignition is ON. 5 Release the brake pedal. ACC ON Set ignition to OFF position. 0 Wait, LED will turn solid GREEN for 2 seconds. 6 Wait, LED 2 will flash GREEN. WARNING: Disconnect power last. Disconnect module from vehicle. ACC ON Set ignition to OFF position. 7 Module Programming Procedure completed. 2-2 Mazda 3 Hatchback PTS AT
INSTALLATION CHECKLIST - OF 2 PAGE 7 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. 2-2 Mazda 3 Hatchback PTS AT
INSTALLATION CHECKLIST - 2 OF 2 PAGE 8 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. 2-2 Mazda 3 Hatchback PTS AT
INSTALL GUIDE 2-2 MAZDA 3 SEDAN PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE COM-RSA-MA3-[RSB-DC2] HARDWARE RSB-DC2 ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
T-HARNESS / COMPONENT LOCATOR - OF PAGE 2 OF 8 C BA T00_H 2-2 Mazda 3 Sedan PTS AT
T-HARNESS / WIRING DIAGRAM - OF PAGE 3 OF 8! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY. THE TAKEOVER FEATURE IS NOT AVAILABLE. THE VEHICLE WILL SHUT DOWN WHEN A DOOR IS OPENED. RELAY VS2 UNIT, UNDER STEERING COLUMN (A) VS : WHITE : VEHICLE HARNESS VS4 VS3 2: WHITE 2 2: VEHICLE HARNESS M2 0 07 08 09 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 2 HORN (-) BLUE - 0 OPTIONAL 8 9 34 2 3 4 5 6 7 CLOCK SPRING (B) PARKING LIGHTS SWITCH, LEFT OF STEERING COLUMN (C) M3 0 07 GRAY SILVER DOT - HOOD STATUS (-) INPUT 08 09 0 GRAY BLUE DOT GRAY/BLACK BLUE DOT GRAY/RED BLUE DOT (SWITCH SIDE) (CONNECTOR SIDE) PARKING LIGHT (-) YELLOW - PARKING LIGHT 2 (-) GREEN - : WHITE 2 3 4 5 6 M4 M5 0 07 08 09 0 2 3 4 5 6 7 8 9 20 0 MS MS2 HOOD SWITCH 2 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE SET THE PROGRAMMING OPTION THROUGH WEBLINK AS FOLLOWS: IN MENU #7 INPUTS CONFIGURATION, FOR 4-HOOD INPUT SOURCE SELECT -ANALOG. 2 T00_H 2-2 Mazda 3 Sedan PTS AT
HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 8 C BA T00_W 2-2 Mazda 3 Sedan PTS AT
HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 8! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY. THE TAKEOVER FEATURE IS NOT AVAILABLE. THE VEHICLE WILL SHUT DOWN WHEN A DOOR IS OPENED. KEYLESS (DATA) LTBLUE - 09 : WHITE UNIT, UNDER STEERING COLUMN (A) IGNITION (+) PURPLE - 7 6 5 4 3 2 0 9 8 7 6 5 4 3 2 32 3 30 29 28 27 26 25 24 23 22 2 20 9 8 7 CANH (DATA) WHITE - 07 2: WHITE CANL (DATA) RED - 08 IGNITION (+) LTGREEN - 0 M2 0 GREEN BLACK DOT BLUE BLACK DOT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT GREEN/BLACK BLACK DOT BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 2 (+) YELLOW - 2 GROUND (-) BLACK - 3 ACCESSORY (+) BROWN - 4 PTS (-) LTBLUE - 7 ER (+) GREEN - 23 HORN (-) BLUE - 0 2 0 9 8 7 6 5 4 3 2 24 23 22 2 20 9 8 7 6 5 4 3 8 9 34 2 3 4 5 6 7 2 CLOCK SPRING (B) M3 0 BROWN SILVER DOT BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT PURPLE/WHITE SILVER DOT WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD STATUS (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY PARKING LIGHT (-) YELLOW - PARKING LIGHT 2 (-) GREEN - : WHITE PARKING LIGHTS SWITCH, LEFT OF STEERING COLUMN (C) 2 3 4 5 6 M4 0 EMPTY EMPTY BROWN/RED - CANH BROWN/YELLOW - CANL BLUE/RED BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED - PTS (-) OUTPUT 2 GRAY/YELLOW 3 GREEN/RED - KEYLESS (DATA) 4 ORANGE/WHITE 5 BROWN - ACCESSORY (+) IN/OUT 6 ORANGE/BLACK 7 PINK - IGNITION (+) IN/OUT 8 PURPLE - ER (+) OUTPUT 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) M5 0 GRAY/BLACK BLUE DOT - PARKING LIGHT 2 (-) SWITCH SIDE WHITE/BLACK BLUE DOT - IGNITION (+) GRAY/RED BLUE DOT - PARKING LIGHT 2 (-) CONNECTOR SIDE WHITE/RED BLUE DOT - IGNITION (+) GRAY BLUE DOT - PARKING LIGHT (-) OUTPUT WHITE BLUE DOT T00_W HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE SET THE PROGRAMMING OPTION THROUGH WEBLINK AS FOLLOWS: IN MENU #7 INPUTS CONFIGURATION, FOR 4-HOOD INPUT SOURCE SELECT -ANALOG. 2-2 Mazda 3 Sedan PTS AT
MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF 8 >> WARNING: All vehicle doors must be closed and locked prior to remote start sequence. Connect module to computer and proceed with extended programming. 2 ACC ON vehicle for 5 seconds. 0 ACC ON Set ignition to ON position. 07 Connect power first. Connect module to vehicle. 3 Press and hold the brake pedal. Wait, LED will turn solid RED to confirm that the ignition is ON. 08 ACC ON Set ignition to ON position. 4 Press and release the module s programming button. Wait 0 seconds, LED will flash GREEN rapidly. 09 Wait, LED will turn solid RED to confirm that the ignition is ON. 5 Release the brake pedal. ACC ON Set ignition to OFF position. 0 Wait, LED will turn solid GREEN for 2 seconds. 6 Wait, LED 2 will flash GREEN. WARNING: Disconnect power last. Disconnect module from vehicle. ACC ON Set ignition to OFF position. 7 Module Programming Procedure completed. 2-2 Mazda 3 Sedan PTS AT
INSTALLATION CHECKLIST - OF 2 PAGE 7 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. 2-2 Mazda 3 Sedan PTS AT
INSTALLATION CHECKLIST - 2 OF 2 PAGE 8 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. 2-2 Mazda 3 Sedan PTS AT
INSTALL GUIDE 2-2 MAZDA 6 PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE COM-RSA-MA3-[RSB-DC2] HARDWARE RSB-DC2 ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
T-HARNESS / COMPONENT LOCATOR - OF PAGE 2 OF 8 C BA T0_H 2-2 Mazda 6 PTS AT
T-HARNESS / WIRING DIAGRAM - OF PAGE 3 OF 8! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY. THE TAKEOVER FEATURE IS NOT AVAILABLE. THE VEHICLE WILL SHUT DOWN WHEN A DOOR IS OPENED. RELAY VS2 : WHITE UNIT, UNDER STEERING COLUMN (B) VS : VEHICLE HARNESS VS4 2: WHITE VS3 2: VEHICLE HARNESS 2 M2 0 07 08 09 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 2 HORN (-) BLUE - 0 OPTIONAL 8 9 34 2 3 4 5 6 7 CLOCK SPRING (D) PARKING LIGHTS SWITCH, LEFT OF STEERING COLUMN (C) M3 0 07 GRAY SILVER DOT - HOOD STATUS (-) INPUT 08 09 0 GRAY BLUE DOT GRAY/BLACK BLUE DOT GRAY/RED BLUE DOT (SWITCH SIDE) (CONNECTOR SIDE) PARKING LIGHT (-) YELLOW - PARKING LIGHT 2 (-) GREEN - : WHITE 2 3 4 5 6 M4 M5 0 07 08 09 0 2 3 4 5 6 7 8 9 20 0 MS MS2 HOOD SWITCH 2 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE SET THE PROGRAMMING OPTION THROUGH WEBLINK AS FOLLOWS: IN MENU #7 INPUTS CONFIGURATION, FOR 4-HOOD INPUT SOURCE SELECT -ANALOG. 2 T0_H 2-2 Mazda 6 PTS AT
HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 8 C BA T0_W 2-2 Mazda 6 PTS AT
HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 8! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY. THE TAKEOVER FEATURE IS NOT AVAILABLE. THE VEHICLE WILL SHUT DOWN WHEN A DOOR IS OPENED. KEYLESS (DATA) GREEN/ORANGE - 09 : WHITE UNIT, UNDER STEERING COLUMN (A) IGNITION (+) PURPLE - 7 6 5 4 3 2 0 9 8 7 6 5 4 3 2 32 3 30 29 28 27 26 25 24 23 22 2 20 9 8 7 CANH (DATA) WHITE OR WHITE/BLACK - 07 2: WHITE CANL (DATA) RED OR RED/YELLOW - 08 IGNITION (+) LTGREEN/RED - 0 M2 0 GREEN BLACK DOT BLUE BLACK DOT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT GREEN/BLACK BLACK DOT BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 2 (+) YELLOW - 2 GROUND (-) BLACK - 3 ACCESSORY (+) BROWN/RED - 4 PTS (-) RED/BLACK - 7 ER (+) BROWN/BLACK - 23 HORN (-) BLUE - 0 2 0 9 8 7 6 5 4 3 2 24 23 22 2 20 9 8 7 6 5 4 3 8 9 34 2 3 4 5 6 7 2 CLOCK SPRING (B) M3 0 BROWN SILVER DOT BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT PURPLE/WHITE SILVER DOT WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD STATUS (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY PARKING LIGHT (-) YELLOW - PARKING LIGHT 2 (-) GREEN - : WHITE PARKING LIGHTS SWITCH, LEFT OF STEERING COLUMN (C) 2 3 4 5 6 M4 0 EMPTY EMPTY BROWN/RED - CANH BROWN/YELLOW - CANL BLUE/RED BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED - PTS (-) OUTPUT 2 GRAY/YELLOW 3 GREEN/RED - KEYLESS (DATA) 4 ORANGE/WHITE 5 BROWN - ACCESSORY (+) IN/OUT 6 ORANGE/BLACK 7 PINK - IGNITION (+) IN/OUT 8 PURPLE - ER (+) OUTPUT 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) M5 0 GRAY/BLACK BLUE DOT - PARKING LIGHT 2 (-) SWITCH SIDE WHITE/BLACK BLUE DOT - IGNITION (+) GRAY/RED BLUE DOT - PARKING LIGHT 2 (-) CONNECTOR SIDE WHITE/RED BLUE DOT - IGNITION (+) GRAY BLUE DOT - PARKING LIGHT (-) OUTPUT WHITE BLUE DOT T0_W HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE SET THE PROGRAMMING OPTION THROUGH WEBLINK AS FOLLOWS: IN MENU #7 INPUTS CONFIGURATION, FOR 4-HOOD INPUT SOURCE SELECT -ANALOG. 2-2 Mazda 6 PTS AT
MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF 8 >> WARNING: All vehicle doors must be closed and locked prior to remote start sequence. Connect module to computer and proceed with extended programming. 2 ACC ON vehicle for 5 seconds. 0 ACC ON Set ignition to ON position. 07 Connect power first. Connect module to vehicle. 3 Press and hold the brake pedal. Wait, LED will turn solid RED to confirm that the ignition is ON. 08 ACC ON Set ignition to ON position. 4 Press and release the module s programming button. Wait 0 seconds, LED will flash GREEN rapidly. 09 Wait, LED will turn solid RED to confirm that the ignition is ON. 5 Release the brake pedal. ACC ON Set ignition to OFF position. 0 Wait, LED will turn solid GREEN for 2 seconds. 6 Wait, LED 2 will flash GREEN. WARNING: Disconnect power last. Disconnect module from vehicle. ACC ON Set ignition to OFF position. 7 Module Programming Procedure completed. 2-2 Mazda 6 PTS AT
INSTALLATION CHECKLIST - OF 2 PAGE 7 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. 2-2 Mazda 6 PTS AT
INSTALLATION CHECKLIST - 2 OF 2 PAGE 8 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. 2-2 Mazda 6 PTS AT
INSTALL GUIDE 2 MAZDA CX-3 PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE COM-RSA-MA3-[RSB-DC2] HARDWARE RSB-DC2 ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
T-HARNESS / COMPONENT LOCATOR - OF PAGE 2 OF 8 B C A T0_H 2 Mazda CX-3 PTS AT
T-HARNESS / WIRING DIAGRAM - OF PAGE 3 OF 8! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY. THE TAKEOVER FEATURE IS NOT AVAILABLE. THE VEHICLE WILL SHUT DOWN WHEN A DOOR IS OPENED. RELAY VS2 : WHITE UNIT, UNDER STEERING COLUMN (A) VS : VEHICLE HARNESS VS4 2: WHITE VS3 2: VEHICLE HARNESS 2 M2 0 07 08 09 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 2 HORN (-) PINK - 0 8 CLOCK SPRING (B) 9 34 2 3 4 5 6 7 PARKING LIGHTS SWITCH, LEFT OF STEERING COLUMN (C) M3 0 07 GRAY SILVER DOT - HOOD STATUS (-) INPUT 08 09 0 GRAY BLUE DOT GRAY/BLACK BLUE DOT GRAY/RED BLUE DOT (SWITCH SIDE) (CONNECTOR SIDE) PARKING LIGHT (-) BLUE - 0 PARKING LIGHT 2 (-) BLACK - : WHITE 2 3 4 5 6 7 8 M4 M5 0 07 08 09 0 2 3 4 5 6 7 8 9 20 0 MS MS2 HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE SET THE PROGRAMMING OPTION THROUGH WEBLINK AS FOLLOWS: IN MENU #7 INPUTS CONFIGURATION, FOR 4-HOOD INPUT SOURCE SELECT -ANALOG. T0_H 2 Mazda CX-3 PTS AT
HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 8 B C A T0_W 2 Mazda CX-3 PTS AT
HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 8! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY. THE TAKEOVER FEATURE IS NOT AVAILABLE. THE VEHICLE WILL SHUT DOWN WHEN A DOOR IS OPENED. KEYLESS (DATA) PINK - 09 : WHITE UNIT, UNDER STEERING COLUMN (A) IGNITION (+) BROWN - 7 6 5 4 3 2 0 9 8 7 6 5 4 3 2 32 3 30 29 28 27 26 25 24 23 22 2 20 9 8 7 ACCESSORY (+) PINK- 2: WHITE CANH (DATA) GREEN - 07 CANL (DATA) RED - 08 M2 0 GREEN BLACK DOT BLUE BLACK DOT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT GREEN/BLACK BLACK DOT BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT IGNITION (+) YELLOW - 0 2 (+) PINK - 2 GROUND (-) BLACK - 3 PTS 2 (-) RED - 7 ER (+) GRAY - 23 HORN (-) PINK - 0 2 0 9 8 7 6 5 4 3 2 24 23 22 2 20 9 8 7 6 5 4 3 8 9 34 2 3 4 5 6 7 2 CLOCK SPRING (B) M3 0 BROWN SILVER DOT BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT PURPLE/WHITE SILVER DOT WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD STATUS (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY PARKING LIGHT (-) BLUE - 0 PARKING LIGHT 2 (-) BLACK - PARKING LIGHTS SWITCH, LEFT OF STEERING COLUMN (C) : WHITE 2 3 4 5 6 7 8 M4 0 EMPTY EMPTY BROWN/RED - CANH BROWN/YELLOW - CANL BLUE/RED BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED - PTS (-) OUTPUT 2 GRAY/YELLOW 3 GREEN/RED - KEYLESS (DATA) 4 ORANGE/WHITE 5 BROWN - ACCESSORY (+) IN/OUT 6 ORANGE/BLACK 7 PINK - IGNITION (+) IN/OUT 8 PURPLE - ER (+) OUTPUT 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) M5 0 GRAY/BLACK BLUE DOT - PARKING LIGHT 2 (-) SWITCH SIDE WHITE/BLACK BLUE DOT - IGNITION (+) GRAY/RED BLUE DOTDOT - PARKING LIGHT 2 (-) CONNECTOR SIDE WHITE/RED BLUE - IGNITION (+) GRAY BLUE DOT - PARKING LIGHT (-) OUTPUT WHITE BLUE T0_W HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE SET THE PROGRAMMING OPTION THROUGH WEBLINK AS FOLLOWS: IN MENU #7 INPUTS CONFIGURATION, FOR 4-HOOD INPUT SOURCE SELECT -ANALOG. 2 Mazda CX-3 PTS AT
MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF 8 >> WARNING: All vehicle doors must be closed and locked prior to remote start sequence. Connect module to computer and proceed with extended programming. 2 ACC ON vehicle for 5 seconds. 0 ACC ON Set ignition to ON position. 07 Connect power first. Connect module to vehicle. 3 Press and hold the brake pedal. Wait, LED will turn solid RED to confirm that the ignition is ON. 08 ACC ON Set ignition to ON position. 4 Press and release the module s programming button. Wait 0 seconds, LED will flash GREEN rapidly. 09 Wait, LED will turn solid RED to confirm that the ignition is ON. 5 Release the brake pedal. ACC ON Set ignition to OFF position. 0 Wait, LED will turn solid GREEN for 2 seconds. 6 Wait, LED 2 will flash GREEN. WARNING: Disconnect power last. Disconnect module from vehicle. ACC ON Set ignition to OFF position. 7 Module Programming Procedure completed. 2 Mazda CX-3 PTS AT
INSTALLATION CHECKLIST - OF 2 PAGE 7 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. 2 Mazda CX-3 PTS AT
INSTALLATION CHECKLIST - 2 OF 2 PAGE 8 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. 2 Mazda CX-3 PTS AT
INSTALL GUIDE 2-2 MAZDA CX-5 PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE COM-RSA-MA3-[RSB-DC2] HARDWARE RSB-DC2 ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
T-HARNESS / COMPONENT LOCATOR - OF PAGE 2 OF 8 C BA T0_H 2-2 Mazda CX-5 PTS AT
T-HARNESS / WIRING DIAGRAM - OF PAGE 3 OF 8! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY. THE TAKEOVER FEATURE IS NOT AVAILABLE. THE VEHICLE WILL SHUT DOWN WHEN A DOOR IS OPENED. RELAY VS2 : WHITE UNIT, UNDER STEERING COLUMN (A) VS : VEHICLE HARNESS VS4 2: WHITE VS3 2: VEHICLE HARNESS 2 M2 0 07 08 09 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 2 HORN (-) PURPLE - 0 8 9 34 2 3 4 5 6 7 CLOCK SPRING (B) PARKING LIGHTS SWITCH, LEFT OF STEERING COLUMN (C) M3 0 07 GRAY SILVER DOT - HOOD STATUS (-) INPUT 08 09 0 GRAY BLUE DOT GRAY/BLACK BLUE DOT GRAY/RED BLUE DOT (SWITCH SIDE) (CONNECTOR SIDE) PARKING LIGHT (-) YELLOW - PARKING LIGHT 2 (-) GREEN - : WHITE 2 3 4 5 6 M4 M5 0 07 08 09 0 2 3 4 5 6 7 8 9 20 0 MS MS2 HOOD SWITCH 2 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE SET THE PROGRAMMING OPTION THROUGH WEBLINK AS FOLLOWS: IN MENU #7 INPUTS CONFIGURATION, FOR 4-HOOD INPUT SOURCE SELECT -ANALOG. 2 T0_H 2-2 Mazda CX-5 PTS AT
HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 8 C BA T0_W 2-2 Mazda CX-5 PTS AT
HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 8! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY. THE TAKEOVER FEATURE IS NOT AVAILABLE. THE VEHICLE WILL SHUT DOWN WHEN A DOOR IS OPENED. KEYLESS (DATA) GREEN/ORANGE - 09 : WHITE UNIT, UNDER STEERING COLUMN (A) IGNITION (+) PURPLE - 7 6 5 4 3 2 0 9 8 7 6 5 4 3 2 32 3 30 29 28 27 26 25 24 23 22 2 20 9 8 7 CANH (DATA) WHITE/BLACK - 07 2: WHITE CANL (DATA) RED/YELLOW - 08 IGNITION (+) LTGREEN/RED - 0 M2 0 GREEN BLACK DOT BLUE BLACK DOT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT GREEN/BLACK BLACK DOT BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT 2 WHITE BLACK DOT 2 (+) YELLOW - 2 GROUND (-) BLACK - 3 ACCESSORY (+) BROWN/RED - 4 PTS (-) RED/BLACK - 7 ER (+) BROWN/BLACK - 23 HORN (-) PURPLE - 0 2 0 9 8 7 6 5 4 3 2 24 23 22 2 20 9 8 7 6 5 4 3 8 9 34 2 3 4 5 6 7 2 CLOCK SPRING (B) M3 0 BROWN SILVER DOT BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT PURPLE/WHITE SILVER DOT WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD STATUS (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY PARKING LIGHT (-) YELLOW - PARKING LIGHT 2 (-) GREEN - : WHITE PARKING LIGHTS SWITCH, LEFT OF STEERING COLUMN (C) 2 3 4 5 6 M4 0 EMPTY EMPTY BROWN/RED - CANH BROWN/YELLOW - CANL BLUE/RED BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED - PTS (-) OUTPUT 2 GRAY/YELLOW 3 GREEN/RED - KEYLESS DATA) 4 ORANGE/WHITE 5 BROWN - ACCESSORY (+) IN/OUT 6 ORANGE/BLACK 7 PINK - IGNITION (+) IN/OUT 8 PURPLE - ER (+) OUTPUT 9 RED - 2V (+) INPUT 20 BLACK - GROUND (-) M5 0 GRAY/BLACK BLUE DOT - PARKING LIGHT 2 (-) SWITCH SIDE WHITE/BLACK BLU DOTE - IGNITION (+) GRAY/RED BLUE DOT - PARKING LIGHT 2 (-) CONNECTOR SIDE WHITE/RED BLUE DOT - IGNITION (+) GRAY BLUE DOT - PARKING LIGHT (-) OUTPUT WHITE BLUE DOT T0_W HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE SET THE PROGRAMMING OPTION THROUGH WEBLINK AS FOLLOWS: IN MENU #7 INPUTS CONFIGURATION, FOR 4-HOOD INPUT SOURCE SELECT -ANALOG. 2-2 Mazda CX-5 PTS AT
MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF 8 >> WARNING: All vehicle doors must be closed and locked prior to remote start sequence. Connect module to computer and proceed with extended programming. 2 ACC ON vehicle for 5 seconds. 0 ACC ON Set ignition to ON position. 07 Connect power first. Connect module to vehicle. 3 Press and hold the brake pedal. Wait, LED will turn solid RED to confirm that the ignition is ON. 08 ACC ON Set ignition to ON position. 4 Press and release the module s programming button. Wait 0 seconds, LED will flash GREEN rapidly. 09 Wait, LED will turn solid RED to confirm that the ignition is ON. 5 Release the brake pedal. ACC ON Set ignition to OFF position. 0 Wait, LED will turn solid GREEN for 2 seconds. 6 Wait, LED 2 will flash GREEN. WARNING: Disconnect power last. Disconnect module from vehicle. ACC ON Set ignition to OFF position. 7 Module Programming Procedure completed. 2-2 Mazda CX-5 PTS AT
INSTALLATION CHECKLIST - OF 2 PAGE 7 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX 2 button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. 2 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 20 Installation checklist completed. 2-2 Mazda CX-5 PTS AT
INSTALLATION CHECKLIST - 2 OF 2 PAGE 8 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 2 Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. 2-2 Mazda CX-5 PTS AT
INSTALL GUIDE 2 MAZDA CX-9 PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE COM-RSA-MA3-[RSB-DC2] HARDWARE RSB-DC2 ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.