INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 38143-40201 S 2008 ODYSSEY Issue Date AUG 2008 PARTS LIST Backup Sensor Attachment Kit P/N 08V67-SHJ-100B Backup sensor control unit Right center sensor clip (Black) Left center sensor clip (White) Buzzer 2 Corner sensor clips Switch bracket Switch 12 Wire ties Backup sensor harness 2 Wire ties with clip Backup sensor subharness Small wire tie Control unit bracket Harness clip 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38143-40201 (0808) 08V67-SHJ-1B00-91 1 of 16

Blind nut Backup Sensor Kit P/N 08V67-SHJ-1x0K Washer-screw, 4 x 14 mm Right center sensor Flange bolt, 6 x 12 mm Left center sensor 2 Flange nuts, 6 mm Fuse label 2 Corner sensors TOOL AND SUPPLIES REQUIRED Urethane tape 3 Harness tapes (Silver) #2 Phillips screwdriver Small flat-tip screwdriver Felt-tip pen 10 mm Combination wrench 10 mm and 14 mm Socket Pushpin Ratchet 3 mm and 8 mm Drill bits Eye protection (face shield, safety goggles, etc.) File Diagonal cutters Scissors Masking tape Tape measure Cardboard Isopropyl alcohol Shop towel 24 mm and 26 mm Holesaw (Holesaw set, T/N: AKS052507) Drill Utility knife Touch-up paint 2 of 16 AII 38143-40201 (0808) 2008 American Honda Motor Co., Inc. - All Rights Reserved.

Illustration of the Backup Sensors Installed on the Vehicle BUZZER CONTROL UNIT 3. Remove the rear bumper. Remove the two clips along the bottom of the bumper. Remove the four self-tapping screws from the bumper. Using a flat-tip screwdriver, pry out and remove the bumper bolt covers, then remove the four bumper bolts. With the help of an assistant, release the bumper from the fenderwell, and slide the bumper away from the vehicle. Set the bumper on a blanket. CORNER LEFT CENTER RIGHT CENTER SUB CORNER 7507140B 4 BOLTS 4 BOLT COVERS INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 4 SELF-TAPPING SCREWS 2 S 7625010B 1. Make sure you have the anti-theft code for the audio unit, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38143-40201 (0808) 3 of 16

4. Pull away the weatherstrip from the driver s sliding door sill trim. Remove the driver s sliding door sill trim (five clips). 5 S DRIVER S SLIDING DOOR SILL TRIM 6. Fold down the third-row seat, and remove the spare tire cover (17 tabs). LEFT SIDE TRIM PANEL 17 TABS SPARE TIRE COVER 4122011Y WEATHERSTRIP 7625020B 5. Pull away the weatherstrip from the rear trim panel. Remove the rear trim panel (10 clips and two screws). 7. Remove the anchor bolt and the anchor bolt cover, and take out the spare tire. SPARE TIRE 10 S TRIM PANEL ANCHOR BOLT SCREW ANCHOR BOLT COVER 4122020Y SCREW WEATHERSTRIP 4122041Y 4 of 16 AII 38143-40201 (0808) 2008 American Honda Motor Co., Inc. - All Rights Reserved.

8. Remove the jack cover (two tabs). LEFT SIDE PANEL 10. Pull away the weatherstrip from the left quarter pillar trim. Remove the left quarter pillar trim (two tabs and side curtain airbag clip). With SRS System Shown WEATHERSTRIP 2 TABS LEFT QUARTER PILLAR TRIM JACK COVER SIDE CURTAIN AIRBAG 4708010Y 9. Remove the left second-row seat belt upper anchor cover (two tabs). Remove the left second-row seat belt upper anchor bolt. 2 TABS 11. Remove the left rear side trim panel: Remove the third-row seat rail cover (four clips). 4510010Y 2 TABS 4 S THIRD-ROW SEAT RAIL COVER LEFT SECOND-ROW SEAT BELT UPPER ANCHOR BOLT 29-34 N m (21-25 lb-ft) LEFT SECOND-ROW SEAT BELT UPPER ANCHOR COVER 4508020Y LEFT SIDE TRIM THIRD ROW SEAT 4510020Y 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38143-40201 (0808) 5 of 16

Pull away the weatherstrip from the left rear side trim panel. Remove the second-row seat belt lower anchor bolt. Gently pull the panel towards you to release the eight clips and four retaining clips, release the third-row seat belt through the slit in the panel, disconnect the rear accessory socket connector, and disconnect two vehicle connectors. 4 TABS 8 S 13. Remove the two self-tapping screws, disengage the retaining tab, and pull out the power door control unit. Move the control unit out of the way. LEFT SIDE PANEL POWER DOOR CONTROL UNIT BOLT LEFT SIDE TRIM WEATHERSTRIP SELF-TAPPING SCREWS 4318040Y LEFT SIDE TRIM PANEL ACCESSORY SOCKET CONNECTOR CONNECTORS SECOND-ROW SEAT BELT LOWER ANCHOR BOLT 29-34 N m (21-25 lb-ft) 12. Remove the left rear pillar trim (one cover, one bolt, one clip, and two tabs). TABS 7625030B LEFT PILLAR TRIM 14. While wearing eye protection, drill the left rear body panel using an 8 mm drill bit. To prevent drilling through the vehicle panel, wrap masking tape around the drill bit as shown. After drilling, remove any burrs at the edges of the hole you made using a file, and apply touch-up paint to the edges. Allow the touch-up paint to dry thoroughly. MASKING TAPE 10 mm PANEL BOLT COVER 4318031Y DRILL (8 mm drill bit) 7625040B 6 of 16 AII 38143-40201 (0808) 2008 American Honda Motor Co., Inc. - All Rights Reserved.

15. Install the blind nut into the 8 mm hole you drilled in step 14. Attach the buzzer to the vehicle panel using the 4 x 14 mm washer-screw. If equipped with a vehicle harness, disengage the vehicle clip from the vehicle panel. Remove the tape and the vehicle clip. Attach the harness clip to the vehicle harness with the tape as shown. Secure the buzzer to the vehicle clip before installing it to the vehicle panel. Routing the Backup Sensor Harness 16. From the outside of the vehicle, remove the vehicle grommet. Pass the backup sensor harness through the hole where the vehicle grommet has been removed. Insert the grommet on the backup sensor harness in the hole. GROMMET PANEL If equipped with vehicle harness Remove. TAPE TAPE (Remove.) (Attach.) BUZZER OUTSIDE INSIDE GROMMET GROMMET PANEL BUZZER 4 x 14 mm WASHER- SCREW 8-PIN CONNECTOR 7425062B BLIND NUT 7425051B 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38143-40201 (0808) 7 of 16

17. Install the 2 A fuse label to the fuse case. 2 A FUSE LABEL FUSE CASE WIRE TIE 20. Remove the blue tape from the backup sensor harness. Connect the backup sensor harness 2-pin connector to the vehicle harness 2-pin connector. URETHANE TAPE (Cut in half.) URETHANE TAPE 2-PIN CONNECTOR 2-PIN CONNECTOR BLUE TAPE (Remove.) WIRE TIE 7425070B 18. Route the backup sensor harness along the vehicle harness, and secure the fuse case to the vehicle harness with a wire tie. 19. Secure the backup sensor harness to the vehicle harness with a wire tie. WIRE TIE 7426012B 21. Cut a urethane tape in half, and wrap the connector with the half. Secure the connector to the vehicle harness with a wire tie. 22. Insert the control unit bracket, and connect the backup sensor 14-pin connector to the backup sensor control unit. CONTROL UNIT 14-PIN CONNECTOR CONTROL UNIT BRACKET 7426021B 8 of 16 AII 38143-40201 (0808) 2008 American Honda Motor Co., Inc. - All Rights Reserved.

23. Attach the backup sensor control unit to the vehicle panel, and secure the control unit bracket with a 6 mm flange nut. PANEL 25. If not equipped with a vehicle harness, connect the backup sensor harness to the buzzer and secure the clip on the backup sensor harness to the vehicle panel. BUZZER 2-PIN CONNECTOR PANEL WIRE TIE WITH CONTROL UNIT BRACKET 6 mm FLANGE NUT 7426030B 24. Secure the backup sensor to the vehicle harness with one wire tie. 7426052B 26. Install a wire tie with clip to the backup sensor harness, and secure the clip to the vehicle panel. WIRE TIE 7426040B 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38143-40201 (0808) 9 of 16

27. If equipped with a vehicle harness, remove the tape and release the clip from the backup sensor harness. Connect the backup sensor harness 2-pin connector to the buzzer. (Remove.) TAPE BUZZER 2-PIN CONNECTOR 29. Route the backup sensor harness toward the upper part of the vehicle, and secure the backup sensor harness to the vehicle panel with one wire with clip. If equipped with a vehicle harness, secure the backup sensor harness to the vehicle panel with one wire tie. PANEL WIRE TIES WIRE TIE WIRE TIE WITH WIRE TIES (Remove.) TAPE 28. Secure the backup sensor harness to the vehicle panel with four wire ties. 7426060B 7427012B 30. Secure the backup sensor 8-pin connector to the vehicle panel. 8-PIN CONNECTOR PANEL 7427021B 10 of 16 AII 38143-40201 (0808) 2008 American Honda Motor Co., Inc. - All Rights Reserved.

Installing the Switch 31. On the inside of the left rear pillar trim, measure from the inside of the ribs, and mark the pillar trim at the measurements shown. While wearing eye protection, drill a 3 mm hole at the marked position. Then drill with a 26 mm hole saw. Do not drill with a 1 inch drill bit. Remove any burrs with a file. 32. Insert the switch into the hole made in step 31, and install the switch bracket onto the switch as shown. LEFT PILLAR TRIM UP CONNECTOR 18 mm DOWN RIB LEFT PILLAR TRIM 20 mm LEFT PILLAR TRIM 26 mm HOLE Hole in SIDE VIEW the switch Hole in the switch SMALL WIRE TIE DRILL (3 mm DRILL BIT) 26 mm HOLESAW BRACKET SMALL WIRE TIE BRACKET LEFT PILLAR TRIM 33. Secure the switch bracket to the switch with a small wire tie. 7507052B 7625051B 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38143-40201 (0808) 11 of 16

34. While holding the switch with your hand, plug the backup sensor harness 3-pin connector into the switch as shown. For installation of the connector, check its vertical direction and connect securely so that no unreasonable force is used on the connector part of the switch. 35. For the left rear pillar trim, insert the clip matching the upper tab and install the trim. At the time of installation, take care that the switch does not come in contact with the left rear pillar trim. NOTE: Tapping on the switch can damage the switch connector. LEFT PILLAR TRIM 2 UPPER TABS Do not tap on the switch. LEFT PILLAR TRIM 3-PIN CONNECTOR 7507060B 36. Reinstall the power door control unit that was removed in step 13. 6731700Y 12 of 16 AII 38143-40201 (0808) 2008 American Honda Motor Co., Inc. - All Rights Reserved.

Installing the Backup Sensor 37. On the inside of the rear bumper, locate and pierce the eight scribe marks on the rear bumper with a pushpin. Pierce the hole vertically against the rear bumper. MARK FOR (Mark in the same position of the other side.) 38. While wearing eye protection, drill 3 mm holes at the four pierced marks on the corner of the rear bumper from the outside. Widen the two lower holes with a 24 mm holesaw as shown. Remove any burrs. DRILL (3 mm DRILL BIT) DRILL PUSHPIN MARK FOR MARK FOR (Mark in the same position of the other side.) MARK (Do not pierce through the mark.) MARK (Do not pierce through the mark.) 24 mm HOLESAW Pierce the hole vertically against the rear bumper. DRILL MARK (Do not pierce through the mark.) MARK FOR 26 mm HOLESAW DRILL (3 mm DRILL BIT) Pierce the hole vertically against the rear bumper. 7507083B PUSHPIN Pierce the hole vertically against the rear bumper. MARK FOR Mark in the same position of the other side. 7507073B 39. While wearing eye protection, drill 3 mm holes at the four pierced marks on the center of the rear bumper from the outside. Widen the two lower holes with a 26 mm holesaw as shown. Remove any burrs. NOTE: The two center holes are larger than the two outer holes. 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38143-40201 (0808) 13 of 16

40. From the outside of the rear bumper, insert the right center sensor and left center sensor into the hole as shown. NOTE: Make sure the sensors are inserted into the correct holes. 42. From the outside of the rear bumper, insert the two corner sensors into the holes as shown. NOTE: Make sure the sensors are inserted into the correct holes. RIGHT CENTER LEFT CENTER 7507091B CORNER CORNER 7625070B 41. From the inside of the rear bumper, insert the right center sensor clip (black) and left center sensor clip (white) to the right center sensor and left center sensor. LEFT CENTER (WHITE) RIGHT CENTER (BLACK) 43. From the inside of the rear bumper, insert the two corner sensor clips to the two corner sensors. 2 CORNER S 2 CORNER S LEFT CENTER RIGHT CENTER 7625080B 7625060B 14 of 16 AII 38143-40201 (0808) 2008 American Honda Motor Co., Inc. - All Rights Reserved.

44. Connect the four backup sensor subharness 2-pin connectors to the right center sensor, left center sensor, and two corner sensors. CORNER LEFT CENTER RIGHT CENTER CORNER 46. Using isopropyl alcohol on a shop towel, throughly clean the area where the harness tapes will attach. Secure the backup sensor subharness to the rear bumper with three harness tapes. SUB TAPES 4 SUB 2-PIN CONNECTORS 7507100B 7507120B 45. Secure the backup sensor subharness connector at the green tape with four wire ties. 47. Bring the rear bumper to the vehicle, and connect the backup sensor subharness 8-pin connector to the backup sensor harness 8-pin connector. SUB CONNECTOR 4 WIRE TIES GREEN TAPE 7507110B 8-PIN CONNECTOR SUB 8-PIN CONNECTOR 48. Install the rear bumper back onto the vehicle. 7507130B 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38143-40201 (0808) 15 of 16

49. Check that all wire harnesses are routed properly and that all connectors are plugged in. 50. Reinstall all removed parts. 51. Reconnect the negative cable to the battery. 52. Enter the customer s audio unit anti-theft code, and reset the radio station presets. 53. Reset the clock. 54. Check the operation of the backup sensors as described in the accessory user's information manual supplied. 55. Initialize and test the front window auto up/down function. 16 of 16 AII 38143-40201 (0808) 2008 American Honda Motor Co., Inc. - All Rights Reserved.