Product Category ebus Button Panel Decora Series Setup Guide IPORTANT: www.extron.com Go to www.extron.com for the complete user guide and installation instructions before connecting the product to the power source. Overview The Extron ebus Button Panel (EBP) 05 D and EBP 06 D ebus Button Panels are fully customizable AV system control interfaces for use with Extron IPCP Pro Series Control Processors. They can be mounted in walls or furniture in any standard Decora opening. NOTE: These products are only for use with Extron U listed IPCP Pro controller products. Each EBP button panel includes two ebus ports, which support power and communications between the IPCP Pro control processor and ebus devices. Up to eight ebus endpoint devices such as EBP button panels can be connected to the control processor and to each other in various cabling topologies. Cabling topology refers to the physical layout of cabling interconnections between devices in a network such as an ebus system. ebus systems can include daisy chain, star, or hybrid system (a combination of both types) topologies (see the ebus Technology Reference Guide, available on www.extron.com, for basic diagrams). Every endpoint device must have a unique identification address (bus ID) within the system. Setup involves setting bus ID DIP switches on the EBPs, then using Extron Global Configurator (GC) Plus and Professional software, or Global Scripter programming, to configure the control processor. Once configured, the AV system can be controlled from any of its EBPs. This guide provides basic instructions for an experienced installer to install an EBP 05 D or EBP 06 D button panel. For more details on the EBPs, see the ebus Technology Reference Guide, available on www.extron.com. For details on configuration, see the software help files. EBP Front Panel Features A APTOP DOC CA PC B C DISPAY OFF VOUE D E DVD VIDEO PC VIDEO A Figure. EBP 05 D (left) and EBP 06 D (right) Front Panels NOTE: Use Global Configurator Plus and Professional to configure the EBP buttons and EDs. A Input and Function Buttons if these buttons are used to select an input, they can be configured as a group to act in a mutually exclusive manner. However, the buttons can also be configured to carry out separate functions. In that case, they can be removed from the input group and configured independently. All the buttons are back-lit with EDs to identify the active button. Dim back lighting helps read inactive buttons in low ambient lighting. B Power Buttons are labelled and OFF and control the power to the display device. The button has a nub that can be felt with the finger tips. C Volume Buttons can be used to increment or decrement audio volume. D Transmit ED at the top right corner of the faceplate blinks once when the programmed action of the button is performed. E Volume ED eter these five EDs can be configured to show the volume level.
EBP Series Decora Wall Plates Setup Guide (Continued) EBP Rear and Side Panel Features A +S -S G +V ebus B PWR OAD =.5W C D Figure 2. EBP Decora Plate Rear View (left) and Side View (right) A ebus Connectors (2 blocks) the four-pole captive screw connector blocks use the Extron ebus protocol to connect the panel to a controller and to other panels. B ebus Connection Status ED the ED provides information about the ebus connection status: z Off the unit is not receiving power. z Slow Blink (0.5 Hz) the unit is receiving power but communication with the control processor is not confirmed. z Fast Blink (2.0 Hz) there is a BUS ID address conflict. z ights solidly power and communication are both confirmed. C Reset Button resets the firmware to the factory installed version.. Disconnect the ebus cable that is providing power. 2. Press and hold down the Reset button while reconnecting power. During the reset process, the front panel buttons are not lit and the ebus Connection Status ED is lit. After about 30 seconds, the front panel buttons are lit dimly and the unit firmware is restored to the original factory installed version. For information about updating the unit firmware, see the ebus Technology Reference Guide. D DIP Switches Up to eight units can be connected to one control processor. Each unit connected to the same control processor must have a unique BUS ID, which is set using DIP switches. Planning the System and Installation When planning to install an ebus system you must consider how many EBP button panels to use, maximum cable distance, cabling topology, and mounting. See the ebus Technology Reference Guide for more information about ebus topologies. Installation Step : Get Ready Use the following check list to prepare for the installation. Download and install the latest version of the software, firmware, and device drivers needed to configure the IPCP Pro and control the connected AV products. See the IPCP Pro Series User Guide (available at www.extron.com) for details on software and drivers. Obtain network information (IP addresses, passwords, DHCP settings, and the like) and the AC address for the control processor. Obtain model names, drivers, and setup information for AV devices. Determine which ebus cabling topologies to use and obtain cables, mounting hardware, and any power supplies or hubs required by that configuration. 2
Product Category Step 2: Prepare the Installation Site ATTENTI: Installation and service must be performed by authorized personnel only. installation et l entretien doivent être effectués par le personnel autorisé uniquement. Extron recommends installing the EBP into a grounded, U isted electrical junction box. Extron recommande d installer le EBP dans un boîtier d encastrement électrique mis à la terre, listé U. If the EBP will be installed into fine furniture, it is best to hire a licenced, bonded craftsperson to cut the access hole and perform the physical installation so the surface will not be damaged. S il est prévu d installer le EBP dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et qualifié pour couper le trou d accès et réaliser l installation de telle façon que la surface ne soit pas endommagée. Follow all national and local building and electrical codes that apply to the installation site. Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s appliquent au site de l installation. All electrical installation should be performed by qualified personnel in accordance with local and national building codes, fire and safety codes, and local and national electrical codes. Toute installation électrique devrait être effectuée par un personnel qualifié, conformément aux codes du bâtiment, aux codes incendie et sécurité, et aux codes électriques locaux et nationaux. Americans with Disabilities Act (ADA) compliance When planning where to install these devices, you may need to consider factors affecting accessibility of the button panel such as height from the floor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see sections 307 ( Protruding Objects ) and 308 ( Reach Ranges ) of the 200 ADA Standards for Accessible Design available at http://www.ada.gov/regs200/200adastandards/200adastandards.pdf. Site preparation The EBP 05 D and EBP 06 D fit any standard Decora wall opening. The units ship with a mud ring. In addition, Extron offers an assortment of optional U isted in-wall junction boxes, external wall boxes (EWBs), and surface or tabletop mounting boxes for use with the ebus button panels (see www.extron.com). Step 3: Change the Buttons You can replace a faceplate or one or more of the individual buttons. Some additional buttons ship with the unit. You can order others from www.extron.com. To change the buttons:. Remove the two screws holding the wallplate to the button plate (figure 3, ) and separate the wallplate from the button plate. 2. Insert a small flat-bladed screw driver into the notch at the top of the button plate. Release the catch holding the button plate to the control plate (2). 3. Repeat step 3 to release the catch at the bottom of the button plate. 4. Tilt the top of the button plate forward as you remove it to prevent the buttons falling out. EBP 06 D 2 Wallplate Figure 3. Removing the Button Panel 3
EBP Series Decora Wall Plates Setup Guide (Continued) 5. From the front of the faceplate, press the button or button pair to be replaced backward through its slots in the faceplate until the membrane containing the button is free. 6. On the back of the faceplate, insert the replacement button or button pair into the appropriate slots. Ensure the text is in the correct orientation. Align the two pegs in the button membrane (see figure 4, ) with the holes located at opposite corners of the empty space in the faceplate. 7. Press the two buttons into the faceplate until the pegs on the membrane are seated in the corresponding holes. 8. Repeat steps 5 through 7 for any other buttons that you want to replace. 9. Align the button plate with the back plate, using the pegs on the button plate (2) as guides. 0. Snap the button plate into place.. Reattach the wallplate, using the two screws removed in step. APTOP UTE 2 Step 4: Set the ebus ID Addresses Up to eight units can be connected to one control processor. Each unit connected to the same control processor must have a unique six-bit, binary ebus ID (address), which is set with the DIP switch assembly on the side panel of the EBP (figure 5, ). If other modules have the same bus ID, address conflicts may cause one or more of the panels to not be recognized by the IPCP Pro control processor. Set the bus identification DIP switches for each EBP button panel in the system using the diagrams in this section as a guide. NOTES: By factory default, the EBP 05 D is set to address three (binary: 0000). The EBP 06 D is set to address four (binary: 00000). Any address can be used except address 0 (binary: 000000), which is reserved (as the address of the controller) and may not be used. Switch (on the left) is the highest value (32, the most significant bit) and is labelled. Switch 6 (on the right) is the lowest value (, the least significant bit) and is labelled. Up = on =, Down = off = 0 Figure 4. Replacing Buttons Bus ID (Decimal) Example Addresses Binary Address 0 000000* *Reserved (for controller address) 00000 2 00000 3 0000 (default for EBP 05 D) 4 00000 (default for EBP 06 D) 5 0000 6 0000 7 000 DIP Switch Setting 8 00000 Slide BUS ID Figure 5. Setting the ebus ID 4
Product Category Step 5: Cable All Devices Attach cables using the diagrams in this section as a guide. Connect a 4-pole captive screw connector to each end of the cable, wiring both ends as shown in figure 6. In most cases the EBPs are powered by the IPCP Pro control processor that provides the ebus signal. Power is carried on the V+ pin of each ebus connection. The four connectors are: z +V carries 2 VDC power from the controller, active hub, or power supply z +S carries the positive data signal z -S carries the negative data signal z G ground Extron STP20-2/000 or STP20-2P/000 cable is recommended for ebus connections. +2 VDC + Signal - Signal Drain Wires Red Green White Black +V +S -S G Figure 6. Basic ebus Connector Wiring and Cable Color Code NOTES: The two ebus blocks are interchangeable: either block can be used to connect the unit to a controller or EBDB and either can be used to daisy chain the unit to another EBP. Connect up to eight ebus endpoint devices for each IPCP Pro control processor. Wire the connectors in the same way at both ends. Do NOT power an EBP from more than one power source. Do not exceed a total of 000 feet (305 meters) of cable for connections between the IPCP Pro and all the EBP panels. Power is provided by the IPCP Pro, a PS 220EB power inserter, or an Extron 2 VDC power supply. Connect power cords and power on all the devices. ATTENTI: Always use a power supply supplied or specified by Extron. Use of an unauthorized power supply voids all regulatory compliance certification and may cause damage to the supply and the unit. Utilisez toujours une source d alimentation fournie par Extron. utilisation d une source d alimentation non autorisée annule toute conformité réglementaire et peut endommager la source d alimentation ainsi que l unité. If not provided with a power supply, this product is intended to be supplied by a U isted power source marked Class 2 or PS and rated output 2 VDC, minimum.0 A. Si ce produit ne dispose pas de sa propre source d alimentation électrique, il doit être alimenté par une source d alimentation certifiée U de classe 2 ou PS et paramétré à 2 VDC et,0 A minimum. Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities. Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une utilisation dans les espaces d aération ou dans les cavités murales. The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/ NFPA 70, article 725 and the Canadian Electrical Code part, section 6. The power supply shall not be permanently fixed to building structure or similar structure. Cette installation doit toujours être en accord avec les mesures qui s applique au National Electrical Code ANSI/ NFPA 70, article 725, et au Canadian Electrical Code, partie, section 6. a source d alimentation ne devra pas être fixée de façon permanente à une structure de bâtiment ou à une structure similaire. 5
EBP Series Decora Wall Plates Setup Guide (Continued) EBPs that are relatively far from the control processor (see the ebus Technology Reference Guide on www.extron.com for details) can be connected to an optional Extron PS 220EB ebus power inserter, or an Extron 2 VDC desktop power supply as shown in the following diagrams. CO Tx Rx G RTS CTS POWER VO 2V.0A AX V C G IPCP Pro CO 2 Tx Rx G REAYS 2 C DIGITA I/O 2 3 4 G ebus +V +S -S G PWR OUT = 6W X IR/S S G IPCP PRO 250 AC: 00-05-A6-XX-XX-XX S/N: ####### E###### AN 00-240V 50-60Hz 0.6A AX Power Input (00-240 VAC, 50-60 Hz) ATTENTI: Do NOT connect the power pin to any device that is already powered by the IPCP Pro control processor or by an additional power supply. + V + S G S + V + S G S S + V + S G ebus 24 WATTS AX + V + S S G X EBP ebus Panel(s) + V + S S G + V + S S G PS 220EB 3/6" (5 mm) ax. +2 VDC + Signal - Signal ebus Connections Connect up to five (5) ebus endpoint devices to the PS 220EB. Wire the connectors the same at both ends. All ports are identical and interchangeable. + V + S S G ebus port on an EBP or other ebus endpoint device + Signal - Signal Tie drain wires to ground. Figure 7. Cabling an ebus System with an PS 220EB Power Inserter + V + S S G + V + S S G ebus 3/6" (5 mm) ax. ebus port on an IPCP Pro Control Processor ebus port on an EBP or other ebus Endpoint + V + S S G + V + S S G - Signal + Signal Tie drain wires to ground. - Signal + Signal +2 VDC EBP 05 D Rear Panel Power Input, External Power Supply (optional) Connect to an Extron 2 VDC, A, power supply. +2 VDC input Return Smooth Ridged External Power Supply (2 VDC, A max.) all Devices NOTE: Check the polarity of the power supply before connecting it to the EBP. Figure 8. Cabling EBP Panels with an Extron 2 VDC, A Power Supply 6
Product Category Step 6: Configure the System NOTES: System configuration requires an IP network connection to the IPCP Pro. See the IPCP Pro Series User Guide for information about the control processors and their ports. EBP bus ID DIP switches should be set prior to uploading the configuration to the IPCP Pro. See the Global Configurator Help file as needed for step-by-step instructions and detailed information. The help file for GC includes an introduction to the software, and how to start a project and configuration.. Create a new Global Configurator Plus or Professional project and configure the controller and any ebus devices. The configuration tells the controller how its ports function; how to control other products; what to monitor; when to do things; and whom to notify, how, and under what circumstances. a. Configure ports on the control processor. z Select device drivers and link them to each assigned port. z Configure settings (serial protocol, relay behavior, digital input, volume control settings) as needed. b. Set up monitors, schedules, macros, and local variables. c. Set up the ebus button panel buttons: assign appropriate commands and actions, macros, timers, local variables monitors, or feedback to the buttons. 2. Save the project. 3. Build and upload the system configuration to the control processor. Step 7: Test and Troubleshoot. Verify that the DIP switches on the EBPs are set to the desired address on each unit and that there are no DIP switch address conflicts in the system. As mentioned in the rear panel features diagram in Step 4: Set the ebus ID Addresses on page 4, the ebus ED lights steadily (solid) when power and communication are present and there are no bus ID address conflicts. 2. Verify that cables to and from the EBPs are wired the same at each end (pin to pin, pin 2 to pin 2, and so forth). 3. Test the system. z Press buttons on the EBPs and ensure the buttons light as desired and that the appropriate control commands or functions are triggered. z Ensure that the audio output responds correctly to the volume knob or button. Also ensure that the volume EDs light correctly as you increase or decrease the audio gain. 4. ake adjustments to wiring, bus ID address, or system configuration as needed. Remember that the rear panel ports and DIP switches will not be accessible after the EBP is mounted. If needed, upload a revised configuration to the control processor. If you have questions during installation and setup, call the Extron S3 Sales & Technical Support Hotline or the Extron S3 Control Systems Support Hotline (.800.633.9877). Step 8: ount the EBPs EBP panels can be installed directly into the wall using a -gang wall mounting bracket (mud ring) or a U-approved wall box. ATTENTI: All electrical installation should be performed by qualified personnel in accordance with local and national building codes, fire and safety codes, and local and national electrical codes. Toute installation électrique devrait être effectuée par un personnel qualifié, conformément aux codes du bâtiment, aux codes incendie et sécurité, et aux codes électriques locaux et nationaux. Prior to mounting:. If it has not already been done, feed all device cables through the wall or furniture. 2. Ensure that cables are connected to the EBP rear panel (see EBP Rear and Side Panel Features on the previous page). 7
EBP Series Decora Wall Plates Setup Guide (Continued) ounting with a Wall ounting Bracket ount an EBP with a wall mounting bracket as follows:. ark the position of the hole (3.6" [9.7 cm] H x 2.3" [5.42 cm] W) on the wall in the desired location. Use a level to ensure hole is marked at the correct angle. 2. Use a drywall saw to cut a hole (). 3. Insert the mounting bracket into the hole. Use a screw driver to turn and tighten the locking arms until they clamp the mud ring to the mounting surface (2). Do not overtighten. 4. If necessary, set the DIP switches to give the panel a unique ID number (3). 5. Use the two provided Phillips head screws to secure the control plate to the mounting bracket (4). 6. Use the two screws provided to secure the Decora wall plate to the control plate (5). 3.6" 2.3" 2 Wall Wall ounting Bracket 3 4 5 EBP 06 D ounting with a U isted Electrical Junction Box The wall box is not provided and must be purchased separately. Ensure the wall box is the correct size for the EBP.. Install the junction box by following the instructions provided by the manufacturer. 2. ocate a suitable wall stud and mark the hole on the wall. Use a level to ensure hole is marked at the correct angle. 3. Use a drywall saw to cut the hole. Follow the instructions of the wall box manufacturer for the correct dimensions of the hole to be cut. 4. Use at least two screws or nails to secure the wall box to the wall stud. 5. Follow steps 4 to 6 in ounting with a Wall ounting Bracket (above) to complete the installation. Electrical Junction Box Wallplate Figure 9. ounting with a Wall ounting Bracket 3 4 5 Decora Wall Plate Figure 0. ounting with a U isted Electrical Junction Box 8
Product Category Removing Decora ount EBPs If you need to remove a Decora EBP from where it has been mounted, follow these steps:. Remove the two screws holding the face plate to the button plate (). 2. Remove the two screws holding the button plate to the junction box or wall mounting bracket (2). 3. Remove the plate from the wall (3) and remove the ebus connector. 2 Electrical Junction Box 3 Decora Wall Plate Figure. Removing the EBP 06 D 9
EBP Series Decora Wall Plates Setup Guide (Continued) Extron Headquarters +.800.633.9876 (Inside USA/Canada Only) Extron USA - West Extron USA - East +.74.49.500 +.99.850.000 +.74.49.57 FAX +.99.850.00 FAX Extron Europe +800.3987.6673 (Inside Europe Only) +3.33.453.4040 +3.33.453.4050 FAX Extron Asia +65.6383.4400 +65.6383.4664 FAX Extron Japan +8.3.35.7655 +8.3.35.7656 FAX Extron China +86.2.3760.568 +86.2.3760.566 FAX Extron iddle East +97.4.299.800 +97.4.299.880 FAX Extron Australia +6.8.835.288 +6.8.835.25 FAX Extron India 800.3070.3777 (Inside India Only) +9.80.3055.3777 +9.80.3055.3737 FAX 0 206 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com 68-449-50 Rev. A 08 6