Seamer Lubrication Suggestions, Requirements & Specifications By Pneumatic Scale Angelus CAUTION: Contact your lubricant suppliers to verify the compatibility of lubricant with paints and components on the seamer before use. Some additives and base oil may affect stability of internal & external coatings resulting severe machine internal damage. 1/6
PNEUMATIC SCALE SANGELUS SERVICE NOTICE LUBRICATION Appropriate Lubricants are essential to the longevity of the machine. Quality engineering is of no value if good maintenance practices are ignored or poor quality or improper lubricants are employed. Generally, good quality lubricants of the correct type will provide long, trouble-free service. In some cases, we recommend very specific products for successful operation. When oil circulation and filtration systems are used, monitoring oil integrity on a monthly basis is recommended. Oil change out on circulating systems should never exceed a six month period or two thousand hours of run time whichever comes first, unless specified & certified by lubricant suppliers. More and more companies are choosing to use food grade lubricants throughout their machines. Historically, food grade lubricants had shorter service life and poorer wear protection than regular petroleum lubricants. Improved additives and synthetic base oils have done much to overcome this shortfall. Paying close attention to maintenance practices and properly chosen lubricants are keys for trouble-free operation of your Pneumatic Scale Angelus Seamers. USDA eliminated their internal group that registered Non Food Compounds such as Lubricants H1 and H2 in 1998. They still have the responsibility for monitoring food and beverage plants to make sure they comply in the use of these lubricants. After several years of self certification by lubricant companies, NSF International was approved in 2001 as a 3rd party registrant for Non Food Compounds. NSF uses guidelines originally set up by USDA conforming to ingredients as specified by the FDA. As an equipment manufacturer, it is our responsibility to specify the lubricants that will meet the application requirements. Due to the high cost and the duration of time to put each lubricant through the test, Pneumatic Scale Angelus has no plan to test more lubricants in the near future. As specified in this document, users of Pneumatic Scale Angelus seamers may use lubricant that is equivalent or exceed the performance of the suggested lubricants listed on this document, and lubricant companies are responsible to guarantee the quality and performance of their products. If users decide to change out the lubricant, it is important to specify lubricant that is compatiable with the factory filled lubricants, or a complete flush/clean out the existing lubricant is necessary. Abbreviations of Industry Terms A.S.T.M. U.S.D.A. N.L.G.I. A.G.M.A. F.D.A. A.P.I. S.A.E. I.S.O. cst S.U.S. NSF American Society for Testing and Materials United States Department of Agriculture National Lubricating Grease Institute America Gear Manufacturers Association Food and Drug Administration American Petroleum Institute Society of Automotive Engineers International Organization for Standardization Centistokes Saybolt Universal Seconds National Sanitation Foundation International 2/6
PSANGELUS Model P Seamers Seamer Grease Fittings unless otherwise noted Grease Grade 1 Drive Case EP Gear Lube 220 ** Lower Chuck Cam Area on Model 53P & 58P Seamers only EP Gear Lube 220 ** PSANGELUS Model 41L Seamers Manzel 7 Feed Lubricators, Interlube Systems, Trabon Oil Pump Systems, Oil Filtration and Recirculation Systems Special Seamer Oil 150 PSANGELUS Model 60L Seamers Grease for Lincoln Electroluber, Lower Chuck Bearings (24L616) Grease Grade 0 Grease for all other Fittings Grease Grade 1 Drive Case Oil EP Gear Lube 220 ** In-motion Timer EP Gear Lube 220 ** Can Feed Drive EP Gear Lube 460 ** Can Feed Chain Lubricator Chain Lube 100 PSANGELUS Models 61H, 62H Seamers Manzel 7 Feed Lubricators, Interlube Systems, Trabon Oil Pump Systems, Oil Filtration and Recirculation Systems Special Seamer Oil 150 Filler Drive Gear Case EP Gear Lube 220 ** 61H Seamer Base Grease Grade 1 PSANGELUS Models 81L, 101L, 121L, 12M, 140S Seamers Manzel 7 Feed Lubricators (80,100,120L), Trabon Oil Pump Systems, Oil Filtration and Recirculation Systems Special Seamer Oil 150 Filler Drive Gear Case EP Gear Lube 220 ** Lincoln Electroluber or Hand Greasing Grease Grade 0 80/81/100/101/120/121L Seamer Base (Utilizing Grease Injectors) Grease Grade 1 3/6
PSANGELUS Model 180S Seamers Trabon Oil Pump Systems, Oil Filtration and Recirculation Systems Special Seamer Oil 150 Lincoln Electroluber or Hand Greasing Grease Grade 0 Filler Drive Gear Case EP Gear Lube 220 ** Optional Vari-Speed Inching Mechanism: Worm Gearhead Reducer... Speed Variator Hydraulic System... EP Gear Lube 460 AW Hydraulic Oil 68 * NOTE: DO NOT use grade 1 grease on automatic seaming roll lubrication system. ** NOTE: Application could be substituted with Synthetic Seamer Oil 220. Lubricant Specifications and Manufacturers Caution: Contact your lubricant suppliers to verify the compatibility of lubricant with paints and components on the seamer before use. Some additives and base oil may effect stability of internal & external coatings resulting in severe machine internal damage. Lubricant Manufacturer Technical Support Web Sites: Shell Oil Company: www.shell.com Fuchs Cassida: www.cassida-lubricants.com Fuchs Lubritech: www.fuchs.com Total Lubricants: www.keystonelubricants.com ChevronTexaco Oil Company: www.chevrontexaco.com ExxonMobil: www.exxonmobil.com Swepco: www.swepcousa.com Kluber Lubrication: www.kluber.com Special Seamer Lubricant 150 and 220 150 220 Description: High quality paraffinic petroleum lubricating oil with ashless dispersant, rust and oxidation inhibited, anti-wear protection, non-foaming, extreme pressure protection, and emulsifier. ISO Viscosity Grade 150 220 Viscosity, cst @ 40 C 135 to 165 198 to 242 Viscosity Index, Minimum 100 100 Appearance Bright & Clear Bright & Clear Color, ASTM D-1500, typical 4.0 4.0 Flash Point, COC, C, typical 232 260 Manufacturers of H-2 rated products: Shell Oil Company Aeroshell Oil W 80 Aeroshell Oil W 100 Total Lubricants Seamer Oil 150 Seamer Oil 220 Manufacturers of H-1 (Foodgrade incidental contact) products: Fuchs Lubritech Cassida GLE 150 (synthetic) Cassida GLE 220 (synthetic) Fuchs Lubritech TLS 150 ChevronTexaco Oil Company 4/6 Chevron Seamer Oil FM
EP Gear Lube 220 and 460 220 460 Description: High quality paraffinic petroleum lubricating oil with rust and oxidation inhibitors, extreme pressure additives, thermally stable, good demulsibility and anti-foam protection. ISO Viscosity Grade 220 460 AGMA Grade 5 EP 7EP Viscosity, cst @ 40 C 198 to 242 414 to 506 Viscosity Index, Minimum 100 100 Appearance Bright & Clear Bright & Clear Flash Point, COC, C, typical 260 260 Rust Protection, ASTM D-665B Pass Pass Copper Strip Corrosion, ASTM D-130, Max. 1b 1b Manufacturers: Swepco Swepco 201 Gear ISO 220 Swepco 201 Gear ISO 460 Total Lubricants Carter EP 220 Carter EP 460 Shell Oil Company Omala Gear Oil 220 Omala Gear Oil 460 ExxonMobil Oil Company Mobilgear 630 Mobilgear 634 Chain Lube 100 Description: High quality petroleum lubricating oil with rust and oxidation inhibitors, thermally stable with tackiness additives. ISO Viscosity Grade 100 AGMA Grade 3 Viscosity, cst @ 40 C 90 to 110 Appearance Bright & Clear Flash Point, COC, C, typical 260 Rust Protection, ASTM D-665B Stringiness Pass Observable Manufacturers: Total Lubricants GP- 150 Chain Lubricant 5/6
Anti-Wear Hydraulic Oil 68 Description: High quality petroleum lubricating oil with anti-wear performance, rust and oxidation inhibitors, thermally stable, demulsible. ISO Viscosity Grade 68 Viscosity, cst @ 40 C 61.2 to 74.8 Viscosity Index, Min. 95 Appearance Bright & Clear Flash Point, COC, C, typical 234 Rust Protection, ASTM D-665A Pass Manufacturers: Total Lubricants Azolla ZS 68 Shell Oil Company Tellus 68 ExxonMobil Oil DTE 26 Grease Grades 0 and 1 0 1 Description: High performance grease with extreme pressure protection, high mechanical and thermal stability, oxidation and rust protection, highly water resistant and excellent corrosion protection. NLGI Grade 0 1 Penetration, worked (ASTM D-217) 355-385 310 to 340 Dropping Point, C, Min. 240 240 Thickener Type Base Oil Properties: Lithium complex, Aluminum Complex, or Polyurea Lithium complex, Aluminum Complex, or Polyurea ISO Viscosity Grade, Minimum 150 150 Viscosity, cst @ 40 C, Minimum 105 105 Viscosity Index, Minimum 100 100 Flash Point, COC, C, typical 260 260 Manufacturers: Non Foodgrade (old USDA H-2 rating) Total Lubricants Zeniplex EP 0 Zeniplex EP 1 ExxonMobil Oil Mobilith AW 0 Mobilith AW 1 Manufacturers: Foodgrade (old USDA H-1 rating) Kluber Lubrication Klubersynth UH1 14-151 ExxonMobil Oil Mobilgrease FM 101 Total Lubricants Nevastane HT/AW 0 Nevastane HT/AW 1 Fuchs Lubritech Cassida RLS-0 Cassida RLS-1 6/6