Compact Cylinder ISO Standards [ISO/2] New It is possible to mount small auto switches on surfaces. es can be mounted on any of the surfaces, depending on the installation conditions. Improved flexibility of system design. 2-color indication solid state auto switch Appropriate setting of the mounting position can be performed without mistakes. Operating range ON Red Green Red OFF Proper operating range The green light lights up at a proper operating range. Even if 2-color indication solid state auto switches are fixed at a proper operating range (the green light lights up), the operation may become unstable depending on the installation environment or magnetic field disturbance. (agnetic body, external magnetic field, proximal installation of cylinders with built-in magnet and actuators, temperature change, other factors for magnetic force fluctuation during operation, etc.) NEW s ø0,ø0 added. Series C CAT.ES-1
ISO Standards [ISO/2] Compact Cylinder Series C ø,ø2,ø,ø0,ø0,ø,ø0,ø0 How to Order C With auto switch CD 9 S With auto switch (uilt-in magnet) L F G C ounting style Through-hole/oth ends tapped common (Standard) Foot style Rod side flange style Head side flange style Single clevis style mm 2 2 mm mm 0 0 mm 0 0 mm mm 0 0 mm 0 0 mm Cylinder stroke Refer to page 2 for standard and intermediate strokes. Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Nil Without auto switch (uilt-in magnet cylinder) For the applicable auto switch model, refer to the table below. es are shipped together, (but not assembled). Rod end thread Nil Rod end female thread Rod end male thread Applicable Auto Switches/Refer to pages to 21 for further information on auto switches. Type Solid state switch Reed switch Special function -wire (NPN) V, 9NV 9N -wire (PNP) V 9PV 9P IC circuit 2-wire V 9V 9 -wire (NPN) V, 9NWV 9NW IC circuit -wire (PNP) V 9PWV 9PW Relay, Grommet Yes 2 V 2-wire V 9WV 9W PLC -wire (NPN) 2-wire V, V 9NAV 9AV 9NA 9A -wire (PNP) 2-wire (Non-polar) V 9PAV 9PA PDW IC circuit Grommet -wire (NPN equivalent) V A9V A9 IC circuit Yes V 0 V A9V A9 Relay, 2-wire 2 V No V, V 0 V or less A90V A90 IC circuit PLC Diagnostic indication (2-color indication) Water resistant (2-color indication) agnetic field resistant (2-color indication) Electrical entry Indicator light Wiring (Output) Load voltage DC AC model Lead wire length (m) 0. 1 (Nil) () (L) (Z) None Pre-wired Applicable load Perpendicular In-line connector (N) Lead wire length symbols: 0. m Nil (Example) 9NW Solid state auto switches marked with are produced upon receipt of order. 1 m (Example) 9NW m L (Example) 9NWL m Z (Example) 9NWZ There are other applicable auto switches other than the listed above. For details, refer to page 11. For details about auto switches with pre-wired connector, refer to pages 1 and 19 in est Pneumatics No. 2. Refer to pages and 21 for the D-PDW type. es are shipped together, (but not assembled). 1
ISO Standards [ISO/2] Compact Cylinder Series C Specifications 2 0 0 0 0 Caution e sure to read before handling. qrefer to back cover for Safety Instructions and Handling Precautions for SC Product (-E0-) for Actuators and Auto Switches Precautions. wthis product should not be used as a stopper. euse the PF thread fittings for this cylinder. Theoretical Output Operating direction IN IN IN IN IN IN IN IN IN Unit: N Operating pressure (Pa) 0. 0. 0. 1 9 11 1 11 21 1 9 9 1 9 10 1 210 20 11 1 19 2 02 02 2 2 2 92 0 0 2 0 90 2 2 9 0 110 10 190 210 10 0 00 ounting racket Part No. Foot Flange Single clevis 2 0 0 0 0 C-L0 C-L02 C-L0 C-L00 C-L00 C-L0 C-L00 C-L0 C-F0 C-F02 C-F0 C-F00 C-F00 C-F0 C-F00 C-F0 C-C0 C-C02 C-C0 C-C00 C-C00 C-C0 C-C00 C-C0 Order two foot brackets per cylinder. Parts belonging to each bracket are as follows. Foot, Flange, Single clevis/ody mounting bolt Type Action Fluid Proof pressure aximum operating pressure inimum operating pressure Pneumatic (Non-lube) Double acting, Single rod Air 1. Pa 1.0 Pa 0.0 Pa (ø to ø), 0.0 Pa (ø0, ø0) Without auto switch: to 0 C (No freezing) Ambient and fluid temperature With auto switch: to 0 C (No freezing) Cushion Rubber bumper on both end Stroke length tolerance Note) +1.0 0 mm ounting Through-hole/oth ends tapped common ø to ø 0 to 00 mm/s Piston speed ø0, ø0 0 to 00 mm/s Note) Stroke length tolerance dose not include the amount of bumper change. Standard Stroke to 0, 0 anufacture of Intermediate Stroke Description Part no. Stroke range Example Weight Without Auto Swtich 2 0 0 0 0 111 1 9 With Auto Switch (uilt-in magnet) 11 2 1 2 0 19 0 02 0 0 Unit: g Cylinder stroke 1 2 0 0 0 0 0 0 10 1 10 1 19 2 21 2 0 1 199 21 20 2 21 2 292 2 0 2 29 1 9 0 2 1 9 9 9 1 09 2 9 9 1 0 0 1 1 91 2 902 9 119 11 1 9 91 9 99 111 1 1 1 1 1 19 19 11 1 1 1 191 1 1 9 2 29 21 20 2 20 0 90 1 1 Standard stroke,, 1,, 2, 0,, 0,, 0, 0, 0, 0,, 10, 1,, 2, 0,, 0,, 0, 0, 0, 0, Dealing with the stroke by the 1 mm interval by using an exclusive body with the specified stroke Refer to How to Order for the standard model no. (page at left) to 19 Part no.: C- akes stroke tube 2 Cylinder stroke 0 0 0 Add each weight of auto switches and mounting brackets when mounting an auto switches. Refer to pages to 21 for auto switch weight. Unit: g 10 2 19 1 299 1 1 21 1 2 191 2 2 2 29 9 29 2 99 0 9 0 2 2 9 0 900 92 1 9 1 0 901 9 9 2 0 9 90 1 10 2 0 92 9 0 1 1 1 11 10 1 1 10 1 19 11 0 9 20 2 29 2 29 21 290 09 9 1 0 0 0 10 2
Series C Allowable Lateral Load ake sure to operate strictly within the allowable lateral load range to the rod end. Operation outside of this range may result in shorter service life or damage to the device. Lateral load Allowable Kinetic Energy ake sure to operate strictly within the allowable range of the load weight and maximum speed. Operation outside of this range may cause excessive impact, which may result in the damage to the device. 00 Operating pressure: 1 Pa Stroke Eccentric distance 0 00 Load weight (kg) 1.0 ø0 ø0 ø ø0 ø0 ø ø2 ø Allowable lateral load (N) 0 ø0 ø0 ø ø0 ø0 ø ø2 ø 0.1 0 00 aximum piston speed (mm/s) 1 0 0 0 10 0 Stroke + Eccentric distance Refer to odel Selection in est Pneumatics No.2 for details about model selection procedure.
ISO Standards [ISO/2] Compact Cylinder Series C Construction!1 ø, ø2 With auto switch (uilt-in magnet) i r t!2! y e q! o w u!0 : Rod end male thread ø to ø!2 r t! y i e q! o w u With auto switch (uilt-in magnet)!0 ø0, ø0!2 r t! y i q e! w u With auto switch (uilt-in magnet)!0 Component Parts No. Description aterial Note 1 2 9 11 1 1 Cylinder tube Piston Piston rod Collar Retaining ring umper A umper ushing Wear ring agnet Rod end nut Rod seal Piston seal Tube gasket Aluminum alloy Aluminum alloy Stainless steel Carbon steel Aluminum alloy Aluminum alloy casted Carbon tool steel Urethane Urethane earing alloy Resin Carbon steel NR NR NR Hard anodized Chromated ø, ø2 ø to ø0 Hard chrome plated ø to ø0 Anodized ø0 to ø0 Painted after chromated Phosphate coated ø to ø Nickel plated Replacement Parts/Seal Kit 2 0 0 0 0 Kit no. CQ2-PS CQ22-PS CQ2-PS CQ20-PS CQ20-PS CQ2-PS CQ20-PS CQ20-PS Contents Set of nos. at left!2,!,! Seal kit includes!2,!,!. Order the seal kit, based on each bore size.
Series C ounting olt Should use recommended bolt shown as below table when mounting the cylinder using through-hole. ounting bolt OA thread Note) To install a through-hole type mounting bolt, bore size to 0 mm, make sure to use the flat washer that is provided. ounting olt for C odel C D ounting bolt x l 0 x 0 l x l 0 x 0 l.2 x l 0 x 0 l x l 0 x 0 l x l 90 x 90 l C(D)- - -1 - -2-0 - -0 - -0-0 -0-0 - -10 C(D)2- - -1 - -2-0 - -0 - -0-0 -0-0 - -10 C(D)- - -1 - -2-0 - -0 - -0-0 -0-0 - -10 Fix the cylinder by using the OA thread that are provided with the cylinder tube..2 0 0 0 0 90 9 x 0 l x l x 0 l x l x 0 l x l x 0 l x l x 90 l x 9 l Fix the cylinder by using the OA thread that are provided with the cylinder tube. 0 0 0 90 9 0 1 10 10 x l x 0 l x l x 0 l x l x 0 l x l x 90 l x 9 l x 0 l x 1 l x 10 l x 10 l Fix the cylinder by using the OA thread that are provided with the cylinder tube. odel C D ounting bolt odel C D ounting bolt x l C(D)0-0 x 0 l 0 x 0 l -1 x l x l - 0 x 0 l 0 x 0 l -2 x l x l -0 90 x 90 l 0 x 0 l - 9 x 9 l 11 9 x l -0 0 x 0 l 90 x 90 l - x l 9 x 9 l -0 1 x 1 l 0 x 0 l -0 1 x 1 l 1 x 1 l -0 10 x 10 l 10 x 10 l -0 0 x 0 l 10 x 10 l C(D)0- - -1 - -2-0 - -0 - -0-0 -0-0 - -10 C(D)0- - -1 - -2-0 - -0 - -0-0 -0-0 - -10 C(D)- - -1 - -2-0 - -0 - -0-0 -0-0 - -10 Fix the cylinder by using the OA thread that are provided with the cylinder tube.. 9. 0 0 0 90 9 0 1 10 10 0 0 0 90 9 0 11 1 1 x l x 0 l x l x 0 l x l x 0 l x l x 90 l x 9 l x 0 l x 1 l x 10 l x 10 l Fix the cylinder by using the OA thread that are provided with the cylinder tube. x 0 l x l x 0 l x l x 0 l x l x 90 l x 9 l x 0 l x l x 11 l x 1 l x 1 l Fix the cylinder by using the OA thread that are provided with the cylinder tube. - C(D)0- -1 - -2-0 - -0 - -0-0 -0-0 - Fix the cylinder by using the OA thread that are provided with the cylinder tube. 1 90 9 0 1 11 1 1 1 1 x l x 90 l x 9 l x 0 l x l x 1 l x 11 l x 1 l x l x 1 l x 1 l x 1 l Fix the cylinder by using the OA thread that are provided with the cylinder tube.
ISO Standards [ISO/2] Compact Cylinder Series C Dimensions ø, ø2 [First angle projection] T ød x 0. (2 positions) Port size øn through ( positions) (The same four-place size) Q F H thread effective depth C. 2 øi øo counterbore R ( positions) (The same four-place size) E Flat washer pcs. L 2 x x RA (R) + Stroke A + Stroke OA ( positions) (The same four-place size) K E ø ø2 Width across flats K : Rod end male thread ød H Hexagon width across flats 1 Rod end nut H1 C X L1 asic Style 2 9 0.. x 1.0 x 1.0 Rod End ale Thread 2 A C D E F H I K L N OA O Q RA R T 1 C D H H1 K L1 X 1 1 2 1 1.. x 1.2 x 1.2 x 0. x 0... 1 1 0. 0.
Series C Dimensions ø to ø [First angle projection] G1/ (2 positions) Port size øo counterbore R ( positions) (The same four-place size) Q F Z H thread effective depth C T ød øn through ( positions) (The same four-place size) øi E J Flat washer pcs. L 2 x x RA (R) + Stroke A + Stroke OA ( positions) (The same four-place size) K E Width across flats K : Rod end male thread ød H Hexagon width across flats 1 Rod end nut H1 C X L1 asic Style 0 0 A C D E F H I J K L N OA O Q RA R T Z 1 2 9 2. 9.. 1. x 1.2 x 1.2 x 1. x 1. 9 2 9 2 2 Rod End ale Thread 1 1 1 1 0 0... 1 C D H H1 K L1 X 1 1 19 19...... 19. 19. x 1.0 x 1.0 x 1.2 x 1.2 x 1.2 x 1.2 x 1.2 x 1.2 9 9.. 1. 1. 1. 1. 11 11 1 1 1 1 1 1 2 2 0 0 1 1 1. 1. 19 19 1 1 1 1
ISO Standards [ISO/2] Compact Cylinder Series C Dimensions ø0, ø0 [First angle projection] x 1. effective depth 21 Q F øi 2 x G1/ Z E : Rod end male thread x 1. effective depth 1 ( positions) (The same four-place size) + Stroke A + Stroke ø. through ( positions) (The same four-place size) ø1. counterbore ( positions) (The same four-place size) K E 2. Width across flats K Hexagon width across flats 2 ød x 1. C ød C 2 2 + Stroke A1 + Stroke asic Style 0 0 A C D E F I K Q Z 11 1 2 0 91 111 1 1 1 1 2 2 9 19 2 2 Rod End ale Thread A1 0 92 0.
CZ Series C ounting racket Foot bracket Flange bracket Hexagon socket head cap screw (Accessory) FL x øfd [First angle projection] 2 x øfd LH R /2 Hexagon socket head cap screw (Accessory) 2 x øld FZ FX ødh11 L 2 0 0 0 0 LX LZ LT L LD LH LT LX LZ R X Y 2. 2 1 1. 1. 2 29. 0 2 0 0 2 9 1 2... 2 9 1 1.. Y 1 21 21 2 2 X 9 9 9 11 1 Hexagon socket head cap screw FT 2 0 0 0 0 D 0 0 ø to ø0 FD. 2.. 9. 9. 9 2 9 1 FL 2. 2. FY FV FT FV 0 0 0 0 1 FX 0 2 90 0 10 FY 0 ø, ø2 FZ 9 90 1 1 1 1 Hexagon socket head cap screw Single clevis bracket CL Hexagon socket head cap screw (Accessory) øcd hole H9 CX -0.2-0. CU CW RR CZ 9 2 0 0 0 0 CDH9 CL.... CU 1 1 2 CW 2 2 1 CX 2 2 0 0 0 CZ 0 1 9 11 2... 2 9 RR 9 9 9. Hexagon socket head cap screw
ISO Standards [ISO/2] Compact Cylinder Series C Proper Auto Switch ounting Position (Detection at Stroke End) and Its ounting Height [First angle projection] Reed auto switch D-A9 Solid state auto switch D-9 D-9W D-9AL D-PDW ø, ø2 A W Hs A W Hs ø, ø0, ø0, ø, ø0, ø0 Figures in the table below are used as a reference when mounting the auto switches for stroke end detection. In the case of actually setting the auto switches, adjust them after confirming their operation. model D-A9 A 11. 2. 1. 0 1 0 9.. 0. 0 2. The dimension inside ( ) is for D-A9... 9. 1. 1. 1.. W 1 (.) (.) (.). () 11 (1.) 1 (.) 1 (1.) 1 (.) A 1.. 1. 1 1. 1.. 2. D-9 D-9W 9. 11. 1. 19.. 21. 2. W -0. 1.. 9.. 11.. A 1.. 1. 1 1. 1.. 2. D-9AL 9. 11. 1. 19.. 21. 2. W -2. -0. 1... 9. 1. A.0 9... 11. 19. D-PDW 0. 2.. 1.. 1. W -.0-1 1. 9 1 Hs 0 9.. Negative figures in the table W indicate an auto switch is mounted outward from the edge of the cylinder body. Reed auto switch D-A9V Solid state auto switch D-9V D-9WV D-9AVL ø, ø2 A Hs A Hs ø, ø0, ø0, ø, ø0, ø0 Figures in the table below are used as a reference when mounting the auto switches for stroke end detection. In the case of actually setting the auto switches, adjust them after confirming their operation. model 2 0 0 0 0 D-9V D-A9V D-9WV D-9AVL A Hs A Hs 11.. 1. 1 9... 2... 9. 1. 1. 1.. 2 2 0 1 9. 0 1.. 1. 1 1. 1.. 2. 9. 11. 1. 19.. 21. 2. 2 2 29 2 2
Series C The Number of Surfaces and Grooves Where an Auto Switch Can e ounted (As Direct ounting) The number of the surfaces and grooves where the auto switch can be mounted, by switch type, are shown in the table below. D A C Piping port ounting the D-PDW on a ø to ø2 port surface interferes with the fitting, so it needs to be mounted on a place other than the port surface. For ø to ø0, if the corner of the fitting hexagon interferes with the D-PDW Series, adjust the tightening of the fitting to eliminate the interference. Also, in the case of interference with an elbow type fitting, direct the port of the fitting away from the D-PDW Series. If you have any other questions, please contact SC. View from piston rod end model 2 0 0 0 0 A (ounting groove no.) (1) D-A9, 9 (ounting groove no.) C (ounting groove no.) D (ounting groove no.) A (ounting groove no.) D-PDW (ounting groove no.) C (ounting groove no.) D (ounting groove no.) Operating Range model D-A9(V) D-9(V) D-9W(V) D-9A(V) D-PDW 2 0 0 0 0 9 9 9 9 9. 1... The operating ranges are provided as guidelines including hystereses and are not guaranteed values (assuming approximately ±0% variations). They may vary significantly with ambient environments...... 9 inimum Auto Switch ounting Stroke 2, 0, 0 0, 0 model No. of auto switch mounted 2 pcs. 1 pc. 2 pcs. 1 pc. 2 pcs. 1 pc. 2 pcs. 1 pc. 2 pcs. 1 pc. D-A9 D-A9V D-9 1 1 1 1 D-9W D-9A 1 1 1 1 1 1 1 1 1 1 D-9V D-9WV D-9AV D-PDW 1 1 1 1 esides the models listed in How to Order, the following auto switches are applicable. Normally closed (NC = b contact), solid state auto switch (D-F9G/F9H type, and D-F type) are also available. For details, refer to est Pneumatics No.2. For solid state auto switches, auto switches with a pre-wired connector are also available. Refer to est Pneumatics No.2 for details. 11
ISO Standards [ISO/2] Compact Cylinder Series C ounting of Auto Switch/Direct ounting Style To mount auto switches, follow the instruction illustrated below. <Applicable auto switch> Solid state D-9(V) D-9W(V) D-9A(V) Reed D-A(V) ø to ø0 Watchmakers screw driver mounting screw <Applicable auto switch> Solid state D-PDW ø to ø0 Hexagon socket head cap screw (2. x 9 L) Hexagon socket head cap screw (2. x L) Protrusion mounting bracket Note) Note) When the auto switch mounting bracket is ordered by its part number, it includes all the bracket and bolts in the above chart. Use a watchmakers screwdriver with a handle to mm in diameter when tightening the auto switch mounting screw. Tightening Torque of Auto Switch ounting Screws (N. m) model Tightening torque D-9(V) D-9W(V) 0.0 to 0.1 D-9A(V)L D-A9(V) 0. to 0. Applicable auto switch mounting bracket part no. D-PDW Q-0S q Insert the protrusion on the bottom of the auto switch into the mating part of the auto switch mounting bracket and fix the auto switch and the auto switch mounting bracket temporarily by tightening the hexagon socket head cap screw (2. x 9 L) 1 to 2 turns. w Insert the temporarily tightened mounting bracket into the mating groove of the cylinder/actuator, and slide the auto switch onto the cylinder/actuator through the groove. e Check the detecting position of the auto switch and fix the auto switch firmly with the hexagon socket head cap screw (2. x L, 2. x 9 L). r If the detecting position is changed, go back to step w. The hexagon socket head cap screw (2. x L) is used to fix the mounting bracket and cylinder/actuator. This enables the replacement of the auto switch without adjusting the auto switch position. Note 1) Ensure that the auto switch is covered with the mating groove to protect the auto switch. Note 2) The torque for tightening the hexagon socket head cap screw (2. x L, 2. x 9 L) is 0.2 to 0. N m. Note ) Tighten the hexagon socket head cap screws evenly. Note ) For ø0 or ø0, in the case of mounting the auto switch of the D-PDW Series onto the port surface, if the corner of the fitting hexagon interferes with the auto switch, adjust the tightening of the fitting to eliminate the interference. In the case of interference with an elbow type fitting, direct the port of the fitting away from the auto switch. Such interference must be avoided especially when selecting a speed controller with fittings or speed exhaust controller, etc. Note ) When the cylinder with auto switches is ordered, the body of the cylinder/auto switch and auto switch mounting bracket are shipped together.
Prior to Use Auto Switches Common Specifications 1 Auto Switches Common Specifications Specific Product Precautions efore handling auto switches, refer to Handling Precautions for SC Products (-E0-) for Auto Switches Precautions. Type Operating time Impact resistance Reed auto switch 1.2 ms 00 m/s 2 Solid state auto switch 1 ms or less 00 m/s 2 Insulation resistance Withstand voltage Ambient temperature Enclosure 0 Ω or more at 00 VDC ega (etween lead wire and case) to 0 C IEC029 Standard IP VAC for 1 minute 00 VAC for 1 minute (etween lead wire and case) (etween lead wire and case) The operating time for the D-PDW is 0 ms or less. Lead Wire Lead wire length indication (Example) D-9W L Lead wire length Nil L Z Lead wire length 0. m 1 m m m 0. m 1 m m m Note 1) Lead wire length Z: m Applicable auto switches Solid state auto switch: anufactured upon receipt of order as standard. Note 2) The standard lead wire length for water resistant 2-color indication solid state auto switches is m. (D-9A(V)L can be used with a lead wire of 0. m and m.) Note ) 1 m (): D-9(V), 9W(V), 9A(V)L only. Note ) Lead wire length tolerance Tolerance ±1 mm ±0 mm ±90 mm ±10 mm 1
Prior to Use Auto Switches Common Specifications 2 Specific Product Precautions efore handling auto switches, refer to Handling Precautions for SC Products (-E0-) for Auto Switches Precautions. Auto Switch Hysteresis Hysteresis is the distance between the position at which piston movement operates an auto switch to the position at which reverse movement turns the switch off. This hysteresis is included in part of the operating range (one side). Switch operating Note) position (ON) Hysteresis Reed auto switch: 2 mm or less Solid state auto switch: 1 mm or less Switch operating position (OFF) Note) Hysteresis may fluctuate due to the operating environment. Please contact SC if hysteresis causes an operational problem. Contact Protection ox: CD-P11, CD-P <Applicable switch models> D-A9/A9V The auto switches above do not have a built-in contact protection circuit. A contact protection box is not required for solid state auto switches due to their construction. q Where the operation load is an inductive load. w Where the wiring length to load is greater than m. e Where the load voltage is 0 VAC. Therefore, use a contact protection box with the switch for any of the above cases: The contact life may be shortened (due to permanent energizing conditions.) When the load voltage is increased by more than % to the rating of applicable auto switches above, use a contact protection box (CD-P11) to reduce the upper limit of the load current by % so that it can be set within the range of the load current range, 1 VAC. Contact Protection ox Specifications Part no. CD-P11 Load voltage ax. load current 0 VAC or less 2 ma 0 VAC. ma Lead wire length connection side 0. m Load connection side 0. m CD-P 2 VDC 0 ma Contact Protection ox Internal Circuit CD-P11 Surge absorber Choke coil ~ CD-P Zener diode Choke coil (+) ( ) Contact Protection ox/dimensions Contact Protection ox Connection To connect a switch unit to a contact protection box, connect the lead wire from the side of the contact protection box marked SWITCH to the lead wire coming out of the switch unit. Keep the switch as close as possible to the contact protection box, with a lead wire length of no more than 1 meter. 1
Prior to Use Auto Switches Connection and Example asic Wiring Solid state -wire, NPN Solid state -wire, PNP 2-wire (Solid state) 2-wire (Reed switch) ain curcuit Load ain curcuit Load ain curcuit Load Indicator protection circuit, etc. Load ~ (Power supply for switch and load are separate) ain curcuit Load ain curcuit Load Indicator protection circuit, etc. Load ~ Example of Connection with PLC (Programmable Logic Controller) Sink input specifications -wire, NPN 2-wire Input CO PLC internal circuit Input Source input specifications -wire, PNP CO PLC internal circuit 2-wire Input Input Connect according to the applicable PLC input specifications, as the connection method will vary depending on the PLC input specifications. CO PLC internal circuit CO PLC internal circuit Example of AND (Series) and OR (Parallel) Connection -wire AND connection for NPN output (Using relays) 1 2 Relay Relay Load Relay contact AND connection for NPN output (Performed with auto switches only) 1 2 Load OR connection for NPN output 1 2 Load 2-wire 2-wire with 2-switch AND connection 1 1 2 Load When two auto switches are connected in series, a load may malfunction because the load voltage will decline when in the ON state. The indicator lights will light up when both of the auto switches are in the ON state. Load voltage at ON = Power supply voltage Residual voltage x 2 pcs. = 2 V V x 2 pcs. = V Example: Power supply is 2 VDC Internal voltage drop in auto switch is V. The indicator lights will light up when both auto switches are turned ON. 2-wire with 2-switch OR connection (Solid state auto switch) When two auto switches Load are connected in parallel, 1 malfunction may occur because the load voltage will increase when in the OFF state. 2 Load voltage at OFF = Leakage current x 2 pcs. x Load impedance = 1 ma x 2 pcs. x kω = V Example: Load impedance is kω. Leakage current from auto switch is 1 ma. (Reed auto switch) ecause there is no current leakage, the load voltage will not increase when turned OFF. However, depending on the number of auto switches in the ON state, the indicator lights may sometimes grow dim or not light up, due to the dispersion and reduction of the current flowing to the auto switches.
Solid State Auto Switch Direct ounting Style D-9N(V)/D-9P(V)/D-9(V) Grommet 2-wire load current is reduced (2. to 0 ma). Flexibility is 1. times greater than the conventional model (SC comparison). Using flexible cable as standard spec. Auto Switch Specifications For details about certified products conforming to international standards, visit us at www.smcworld.com. PLC: Programmable Logic Controller D-9, D-9V (With indicator light) model D-9N D-9NV D-9P D-9PV D-9 D-9V Electrical entry direction In-line Perpendicular In-line Perpendicular In-line Perpendicular Wiring type -wire 2-wire Output type NPN PNP Applicable load Power supply voltage Current consumption IC circuit, Relay, PLC,, 2 VDC (. to 2 V) ma or less 2 VDC relay, PLC Load voltage 2 VDC or less 2 VDC ( to 2 VDC) Load current 0 ma or less 2. to 0 ma Internal voltage drop Leakage current 0. V or less at ma (2 V or less at 0 ma) 0 μa or less at 2 VDC V or less 0. ma or less Standard Red LED illuminates when turned ON. CE marking Lead wires Oilproof flexible heavy-duty vinyl cord: ø2. x.2 ellipse, 0.1 mm 2, 2 cores (D-9(V)), cores (D-9N(V), D-9P(V)) Note 1) Refer to page 1 for solid state auto switch common specifications. Note 2) Refer to page 1 for lead wire lengths. Weight Unit: g Caution Precautions Fix the auto switch with the existing screw installed on the auto switch body. The auto switch may be damaged if a screw other than the one supplied is used. model Lead wire length (m) Dimensions 0. 1 D-9N(V) 1 1 D-9P(V) 1 1 D-9(V) 1 Unit: mm Auto Switch Internal Circuit D-9N, D-9NV DC (+) D-9 2. 2. x l Slotted set screw ain circuit 2. 2. DC ( ).2 D-9P, D-9PV ost sensitive position DC (+) D-9V ain circuit DC ( ) 2. x l Slotted set screw 2.2. D-9, D-9V (+) 9. 2. 2. ain circuit 2. ( ) ost sensitive position
2-Color Indication Type Solid State Auto Switch Direct ounting Style D-9NW(V)/D-9PW(V)/D-9W(V) Grommet 2-wire load current is reduced (2. to 0 ma). Flexibility is 1. times greater than the conventional model (SC comparison). Using flexible cable as standard spec. A proper operating range can be determined by the color of the light. (Red Green Red) Caution Precautions Fix the auto switch with the existing screw installed on the auto switch body. The auto switch may be damaged if a screw other than the one supplied is used. Auto Switch Specifications PLC: Programmable Logic Controller D-9W, D-9WV (With indicator light) model Electrical entry direction D-9NW In-line D-9NWV Perpendicular D-9PW In-line D-9PWV Perpendicular D-9W In-line D-9WV Perpendicular Wiring type -wire 2-wire Output type NPN PNP Applicable load Power supply voltage Current consumption IC circuit, Relay, PLC,, 2 VDC (. to 2 V) ma or less 2 VDC relay, PLC Load voltage Load current 2 VDC or less 0 ma or less 2 VDC ( to 2 VDC) 2. to 0 ma Internal voltage drop Leakage current 0. V or less at ma (2 V or less at 0 ma) 0 μa or less at 2 VDC V or less 0. ma or less Standard Weight Operating range... Red LED illuminates. Proper operating range... Green LED illuminates. CE marking For details about certified products conforming to international standards, visit us at www.smcworld.com. Lead wires Oilproof flexible heavy-duty vinyl cord: ø2. x.2 ellipse, 0.1 mm 2, 2 cores (D-9W(V)), cores (D-9NW(V), D-9PW(V)) Note 1) Refer to page 1 for solid state auto switch common specifications. Note 2) Refer to page 1 for lead wire lengths. Unit: g Auto Switch Internal Circuit D-9NW, D-9NWV ain circuit DC (+) model Lead wire length (m) Dimensions 0. 1 D-9NW(V) 1 1 D-9PW(V) 1 1 D-9W(V) 1 Unit: mm D-9PW, D-9PWV DC ( ) DC (+) D-9W 2. 2. x l Slotted set screw ain circuit 2. 2. DC ( ).2 D-9W, D-9WV ain circuit / Display method ON (+) ( ) D-9WV ost sensitive position 2. x l Slotted set screw 2.2 2.. 2. Operating range OFF Display Red Green Red 9. 2. Proper operating range ost sensitive position 1
Water Resistant 2-Color Indication Type Solid State Auto Switch: Direct ounting Style D-9NA(V)/D-9PA(V)/D-9A(V) Grommet Water (coolant) resistant type 2-wire load current is reduced (2. to 0 ma). A proper operating range can be determined by the color of the light. (Red Green Red) Using flexible cable as standard spec. Caution Precautions Fix the auto switch with the existing screw installed on the auto switch body. The auto switch may be damaged if a screw other than the one supplied is used. Auto Switch Internal Circuit D-9NA, D-9NAV ain circuit D-9PA, D-9PAV DC (+) DC ( ) DC (+) Auto Switch Specifications PLC: Programmable Logic Controller D-9A, D-9AV (With indicator light) model Electrical entry direction D-9NA In-line D-9NAV Perpendicular D-9PA In-line D-9PAV Perpendicular D-9A In-line D-9AV Perpendicular Wiring type -wire 2-wire Output type NPN PNP Applicable load Power supply voltage Current consumption IC circuit, Relay, PLC,, 2 VDC (. to 2 V) ma or less 2 VDC relay, PLC Load voltage Load current 2 VDC or less 0 ma or less 2 VDC ( to 2 VDC) 2. to 0 ma Internal voltage drop Leakage current 0. V or less at ma (2 V or less at 0 ma) 0 μa or less at 2 VDC V or less 0. ma or less Standard Weight model Lead wire length (m) 0. 1 Operating range... Red LED illuminates. Proper operating range... Green LED illuminates. D-9NA(V) 1 1 CE marking Lead wires Oilproof flexible heavy-duty vinyl cord: ø2. x.2 ellipse, 0.1 mm 2, 2 cores (D-9A(V)), cores (D-9NA(V), D-9PA(V)) Note 1) Refer to page 1 for solid state auto switch common specifications. Note 2) Refer to page 1 for lead wire lengths. Dimensions D-9A SC 2. x l Slotted set screw D-9PA(V) 1 1 D-9A(V) 1 Unit: g Unit: mm ain circuit DC ( ) 0.2 2. 2 2..2 D-9A, D-9AV ost sensitive position (+) D-9AV ain circuit ( ) 2. x l Slotted set screw 2.2. /Display method Operating range ON OFF 2. SC 2. Display Red Green Red 9. 2. Proper operating range ost sensitive position 1
Grommet Caution Precautions Fix the auto switch with the existing screw installed on the auto switch body. The auto switch may be damaged if a screw other than the one supplied is used. Auto Switch Internal Circuit D-A90, A90V Reed switch Reed Auto Switch Direct ounting Style D-A90(V)/D-A9(V)/D-A9(V) Contact protection box CD-P11 CD-P (±) ( ) ± Auto Switch Specifications PLC: Programmable Logic Controller D-A90, D-A90V (Without indicator light) model Applicable load D-A90, D-A90V IC circuit, Relay, PLC Load voltage aximum load current AC 2 V DC or less 0 ma AC V DC or less 0 ma AC 0 V DC or less ma Contact protection circuit None Internal resistance Standard 1 Ω or less (Including lead wire length of m) CE marking D-A9, D-A9V, D-A9, D-A9V (With indicator light) model Applicable load D-A9, D-A9V Relay, PLC D-A9, D-A9V IC circuit Load voltage 2 VDC 0 VAC to VDC Load current range and aximum load current () to 0 ma to ma ma Contact protection circuit None Internal voltage drop D-A9: 2. V or less (up to ma)/ V or less (up to 0 ma) D-A9V: 2. V or less 0. V or less Standard Red LED illuminates when turned ON. CE marking Weight For details about certified products conforming to international standards, visit us at www.smcworld.com. Lead wires D-A90(V)/D-A9(V)Oilproof heavy-duty vinyl cord, ø2., 0.1 mm 2 x 2 cores (, ), 0. m D-A9(V)Oilproof heavy-duty vinyl cord, ø2., 0.1 mm 2 x cores (,, ), 0. m Note 1) Refer to page 1 for reed auto switch common specifications. Note 2) Refer to page 1 for lead wire lengths. Note ) Under ma, the strength of the indicator light is poor. In some cases, visibility of the indicator light will not be possible where the output signal is less than 2. ma. However, there is no problem in terms of contact output, when an output signal exceeds 1 ma or more. Unit: g D-A9, A9V Reed switch LED Resistor Zener diode Contact protection box CD-P11 CD-P (+) ( ) odel Lead wire length (m) 0. Dimensions D-A90/D-A9/D-A9 2. D-A90 0. D-A90V 0 2 D-A9 0 D-A9V 0 ø2. D-A9 1 D-A9V 1 Unit: mm D-A9, A9V Reed switch DC (+) LED Resistor Reverse current prevention diode DC ( ) Load (+) DC power supply ( ) 2. x L Slotted set screw D-A90V/D-A9V/D-A9V 2. () D-A90 without indicator light ost sensitive position ( ): dimensions for D-A9. Note 1) Operating load is an induction load. Note 2) Wiring to the load is m or longer. Note ) Load voltage is 0 VAC. Use the contact protection box in any of the above listed situations. The contact point life may decrease. (Refer to page 1 for contact protection box.) 2. x L Slotted set screw 2 9.1.1. ø2. D-A90V without indicator light 19 ost sensitive position
agnetic Field Resistant 2-Color Display Solid State Auto Switch D-PDWSC/D-PDWSE (Electrical entry: Pre-wired connector) It is possible to use in an environment which generates a magnetic field disturbance (AC magnetic field). A proper operating range can be determined by the color of the light. (Red Green Red) Caution Precautions For single-phase AC welding machines If it is used for current inverter welders (including rectifying type) and condenser type welders, the magnetic field resistance is reduced. Please contact SC regarding the performance. Auto Switch Internal Circuit D-PDWSC Auto Switch Specifications PLC: Programmable Logic Controller D-PDWSC/E (With indicator light) model D-PDWSC D-PDWSE Applicable load Load voltage Load current Internal voltage drop Leakage current Operating time Standards 2 VDC relay, PLC 2 VDC ( to 2 VDC) to 0 ma V or less 1 ma or less at 2 VDC 0 ms or less Operating range Red LED illuminates. Proper operating range Green LED illuminates. CE marking, UL (CSA), RoHS Lead wire Oilproof heavy-duty vinyl cable, ø., 0. mm 2, 2 cores Impact resistance Switch: 00 m/s 2, Connector: 00 m/s 2 Insulation resistance 0 Ω or more at 00 VDC ega (between lead wire and case) Withstand voltage 00 VAC for 1 minute (between lead wire and case) Ambient temperature to 0 C Enclosure IEC029 standard IP Polarity: Non-polar agnetic Field Resistance If the current of the AC welding machine is 000 A or lower, the auto switch can be used, even if the distance between the welding conductor (gun cable) and the cylinder/actuator or auto switch is 0 mm. Please contact SC when the AC welding current exceeds 000 A. Weight model D-PDWSC Lead wire length (m) 0. 2 For details about certified products conforming to international standards, visit us at www.smcworld.com. D-PDWSE Unit: g Switch main circuit NO. ( ±) NO. ( ± ) Dimensions ody ø. Unit: mm D-PDWSE Switch main circuit /Display method Operating range ON NO.1 ( ±) NO. ( ) ± OFF.2 11 1. ø2. mounting hole 29 00 ost sensitive position mounting bracket (For round groove mounting: Q-0S) 2. Heat shrink tube Note) ø1 Note) A white color heat shrink tube is attached to the D-PDWSE type only. mounting bracket (For square groove mounting: G-02S) Display Red Green Red. (29). (29) Proper operating range 2 1 Connector pin assignment 1. (1.2) ost sensitive position.2 1. (1.2) ost sensitive position When the auto switch is ordered on its own, the auto switch mounting bracket is not enclosed. In that case, please order it separately.
It is possible to use in an environment which generates a magnetic field disturbance (AC magnetic field). A proper operating range can be determined by the color of the light. (Red Green Red) Caution Precautions agnetic Field Resistant 2-Color Display Solid State Auto Switch D-PDW/L/Z (Electrical entry: Grommet) For details about certified products conforming to international standards, For single-phase AC welding machines If it is used for current inverter welders (including rectifying type) and condenser type welders, the magnetic field resistance is reduced. Please contact SC regarding the performance. Auto Switch Specifications PLC: Programmable Logic Controller D-PDW/L/Z (With indicator light) model D-PDW/L/Z Applicable load 2 VDC relay, PLC Load voltage 2 VDC ( to 2 VDC) Load current to 0 ma Internal voltage drop V or less Leakage current 1 ma or less at 2 VDC Operating time 0 ms or less Operating range Red LED illuminates. Proper operating range Green LED illuminates. Standards CE marking, UL (CSA), RoHS Lead wire Oilproof heavy-duty vinyl cable, ø., 0. mm 2, 2 cores, D-PDW: 0. m, D-PDWL: m, D-PDWZ: m Impact resistance Switch: 00 m/s 2 Insulation resistance 0 Ω or more at 00 VDC ega (between lead wire and case) Withstand voltage 00 VAC for 1 minute (between lead wire and case) Ambient temperature to 0 C Enclosure IEC029 standard IP Polarity: Non-polar agnetic Field Resistance If the current of the AC welding machine is 000 A or lower, the auto switch can be used, even if the distance between the welding conductor (gun cable) and the cylinder/actuator or auto switch is 0 mm. Please contact SC when the AC welding current exceeds 000 A. Weight visit us at www.smcworld.com. Unit: g Auto Switch Internal Circuit D-PDW/L/Z Switch main circuit (±) ( ) ± model Lead wire length (m) Dimensions ody 0. ø. D-PDW/L/Z 2 Unit: mm /Display method Operating range ON Display Red Green Red OFF Proper operating range.2 11 1 ø2. mounting hole 29 00 (000, 000) ost sensitive. position mounting bracket (For round groove mounting: Q-0S) mounting bracket (For square groove mounting: G-02S). (29). (29) 1. (1.2) ost sensitive position.2 1. (1.2) ost sensitive position 21 When the auto switch is ordered on its own, the auto switch mounting bracket is not enclosed. In that case, please order it separately.
ISO Standards [ISO/2] Compact Cylinder (ATEX directive category 2) Series -C ø,ø2,ø,ø0,ø0,ø,ø0,ø0 How to Order C D ATEX directive category 2 Compliant with ATEX directive category 2 Nil D L F G C agnet None uilt-in magnet ounting style Through-hole/oth ends tapped common (Standard) Foot style Rod side flange style Head side flange style Single clevis style mm 2 2 mm mm 0 0 mm 0 0 mm mm 0 0 mm 0 0 mm Rod end thread Nil Rod end female thread Rod end male thread Cylinder stroke Refer to page 2 for standard and intermediate strokes. Specifications Type Action Fluid Proof pressure aximum operating pressure inimum operating pressure Ambient and fluid temperature Cushion Stroke length tolerance ounting Piston speed ø to ø ø0, ø0 Pneumatic (Non-lube) Double acting, Single rod Air 1. Pa 1.0 Pa 0.0 Pa (ø to ø) 0.0 Pa (ø0, ø0) to 0 C (No freezing) Rubber bumper on both end +1.0 0 mm Through-hole/oth ends tapped common 0 to 00 mm/s 0 to 00 mm/s Note) Stroke length tolerance dose not include the amount of bumper change. When using an, select the appropriate switch from the following table and order it separately. Applicable auto switch specifications only conforms to Category. (II GD EEx na II Tx - C Ta +0 C IP) For detailed specifications on the D-9P(V), A9(V) and A90(V), please refer to page, 19. (Note: Reed auto switches for 0 VAC and 0 VDC are not within the specification. Type odel Electrical entry Indicator light Wiring (output) Load voltage DC D-9PV- Grommet (Perpendicular) Yes D-9P- Grommet (in-line) -wire 2 V V, V IC circuit D-9PWV- Grommet (Perpendicular) (PNP) Yes D-9PW- Grommet (in-line) (2-color) D-A9V- Yes 2 V V Grommet (Perpendicular) D-A90V- No 2 V or less V V or less IC circuit 2-wire D-A9- Yes 2 V V Grommet (in-line) D-A90- No 2 V or less V V or less IC circuit Lead wire length symbols: 0. m Nil (Example) D-A9- solid state auto switch is available after receiving an order. m L (Example) D-A9L- m Z (Example) D-A9Z- Reed switch Solid state switch AC Lead wire length (m) 0. (Nil) (L) (Z) Applicable load Note) When mounting an auto switch on a -series (Category 2) model, the ATEX class of the cylinder with auto switch changes to Category, which is the same class as the auto switch. Relay, PLC
Safety Instructions Caution: Warning: Danger : Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger. They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC) 1), and other safety regulations. 1) ISO 1: Pneumatic fluid power General rules relating to systems. ISO 1: Hydraulic fluid power General rules relating to systems. IEC 0-1: Safety of machinery Electrical equipment of machines. (Part 1: General requirements) ISO 21-1: anipulating industrial robots - Safety. etc. Warning 1. The compatibility of the product is the responsibility of the person who designs the equipment or decides its specifications. Since the product specified here is used under various operating conditions, its compatibility with specific equipment must be decided by the person who designs the equipment or decides its specifications based on necessary analysis and test results. The expected performance and safety assurance of the equipment will be the responsibility of the person who has determined its compatibility with the product. This person should also continuously review all specifications of the product referring to its latest catalog information, with a view to giving due consideration to any possibility of equipment failure when configuring the equipment. 2. Only personnel with appropriate training should operate machinery and equipment. The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced.. Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2. When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any appropriate source is cut, and read and understand the specific product precautions of all relevant products carefully.. efore machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.. Contact SC beforehand and take special consideration of safety measures if the product is to be used in any of the following conditions. 1. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping, vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or other applications unsuitable for the standard specifications described in the product catalog.. An application which could have negative effects on people, property, or animals requiring special safety analysis.. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. Caution 1. The product is provided for use in manufacturing industries. The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SC beforehand and exchange specifications or a contract if necessary. If anything is unclear, contact your nearest sales branch. Limited warranty and Disclaimer/ Compliance Requirements The product used is subject to the following Limited warranty and Disclaimer and Compliance Requirements. Read and accept them before using the product. Limited warranty and Disclaimer 1. The warranty period of the product is 1 year in service or 1. years after the product is delivered. 2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2. For any failure or damage reported within the warranty period which is clearly our responsibility, a replacement product or necessary parts will be provided. This limited warranty applies only to our product independently, and not to any other damage incurred due to the failure of the product.. Prior to using SC products, please read and understand the warranty terms and disclaimers noted in the specified catalog for the particular products. 2) Vacuum pads are excluded from this 1 year warranty. A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty. Compliance Requirements 1. The use of SC products with production equipment for the manufacture of weapons of mass destruction (WD) or any other weapon is strictly prohibited. 2. The exports of SC products or technology from one country to another are governed by the relevant security laws and regulations of the countries involved in the transaction. Prior to the shipment of a SC product to another country, assure that all local rules governing that export are known and followed. Record of changes Edition s ø0, ø0 added. NZ Safety Instructions e sure to read Handling Precautions for SC Products (-E0-) before using. Akihabara UDX 1F, -1-1, Sotokanda, Chiyoda-ku, Tokyo 1-0021, JAPAN Phone: 0--29 Fax: 0-29- URL http://www.smcworld.com 09 SC Corporation All Rights Reserved Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. D-G 1st printing JO printing NZ 000SZ Printed in Japan. This catalog is printed on recycled paper with concern for the global environment.