hrottle check valve ype Z2FS Size 6 Component series 3X Maximum operating pressure 350 bar [5076 psi] Maximum flow 250 l/min [66 US gpm] tb022 able of contents Content Page Features Ordering code 2 Symbols 2 Function, section 3 echnical data 4 Characteristic curves 5 Unit dimensions 6 Features Sandwich plate valve Porting pattern to ISO 440-07-07-0-05 and NFPA 3.5. R2-D07 For limiting the flow in 2 actuator ports Adjustment element: Spindle with hexagon socket For meter-in or meter-out throttling
Ordering code Z2FS 6 8 3X * hrottle check valve, sandwich plate design Size 6 = 6 hrottle check valve Side A and B = hrottle check valve Side A = A hrottle check valve Side B = B Adjustment element Spindle with hexagon socket = 8 Component series 30 to 39 = 3X (30 to 39: unchanged installation and connection dimensions) Standard types and components are given in the EPS (standard price list). S = Further details in clear text Seal material No code = NBR seals V = FKM seals (other seals on request) Attention! Observe compatibility of seals with hydraulic fluid used ( A8 3X/S) meter-in throttling on side A ( B8 3X/S) meter-in throttling on side B ( 8 3X/S) meter-in throttling on sides A and B S2 = ( A8 3X/S2) meter-out throttling on side A ( B8 3X/S2) meter-out throttling on side B ( 8 3X/S2) meter-out throttling on sides A and B Symbols ( = component side, 2 = plate side) Meter-in throttling S Meter-out throttling S2 Variant L P X L P X Variant A L P X L P X Variant B L P X L P X
Function, section Valves of type Z2FS are throttle check valves of sandwich plate design. hey are used to limit the flow in one or two actuator ports. wo throttle check valves, which are arranged symmetrically to each other, limit flows (through adjustable throttle spools) in one direction and allow free return flow in the opposite direction. In the case of meter-in throttling the hydraulic fluid is fed through channel A via throttling point () to actuator A2. he throttle spool (2.) can be axially adjusted by means of spindle (3), thus allowing throttling point () to be adjusted. At the same time, the hydraulic fluid present in channel A gets via bore (4) to spool side (5). ogether with the spring force, the applied pressure holds the throttle spool (2.) in the throttling position. he hydraulic fluid returning from actuator B2 shifts throttle spool (2.2). he valve then acts as check valve with free flow. Depending on the variant ( S or S2 ) throttling can be effective in the inflow or outflow. Flow limitation o change the velocity of an actuator, the throttle check valve is to be installed between the directional valve and the subplate. 3 5 4 2. 2.2 Meter-in throttling L A P B X 2 = component side 2 = plate side
echnical data (for applications outside these parameters, please consult us!) General Weight kg [lbs] ca. 4.7 [0.4] Installation orientation Optional Ambient temperature range C [ F] 30 to +80 [ 22 to +76] (NBR seals) 20 to +80 [ 4 to +76] (FKM seals) Hydraulic Maximum operating pressure bar [psi] 350 [5076] Maximum flow l/min [US gpm] 250 [66] Hydraulic fluid Mineral oil (HL, HLP) to DIN 5524 ) ; fast bio-degradable hydraulic fluids to VDMA 24568 (see also RE 9022); HEG (rape seed oil) ) ; HEPG (polyglycols) 2) ; HEES (synthetic esters) 2) ; other hydraulic fluids on request Hydraulic fluid temperature range C [ F] 30 to +80 [ 22 to +76] (NBR seals) 20 to +80 [ 4 to +76] (FKM seals) Viscosity range mm 2 /s [SUS] 2.8 to 380 [3 to 760] Permissible max. degree of contamination of the hydraulic fluid - cleanliness class to ISO 4406 (c) Class 20/8/5 3) ) Suitable for NBR and FKM seals 2) Suitable only for FKM seals 3) he cleanliness classes specified for components must be adhered to in hydraulic systems. Effective filtration prevents malfunction and, at the same time, prolongs the service life of components. For the selection of filters, see data sheets RE 50070, RE 50076, RE 5008, RE 50086, RE 50087 and RE 50088.
Characteristic curves (measured with HLP46, ϑ oil ( = 90 SUS) = 40 C ±5 C [04 F ± 9 F]) Pressure differential in bar [psi] [6] [00] [80] [60] [40] [20] [0] 8 6 4 2 0 p-q V characteristic curves (through check valve, with closed throttle) 25 50 75 00 25 50 75 [0] [5] [0] [5] [20] [25] [30] [35] [40] [45] [50] [55] [60] [66] Flow in l/min [US gpm] 200 225 250 p-q V characteristic curves (throtlte position constant) [3626] [2900] 250 200 4 5 6 6,5 7 7,5 8 8,5 Pressure differential in bar [psi] [275] [450] [725] [45] [72.5] 50 00 50 0 5 9 0 2 4 6 hrottle position in turns [0] 0 50 00 50 200 250 [0] [5] [0] [5] [20] [25] [30] [35] [40] [45] [50] [55] [60] [66] Flow in l/min [US gpm]
Unit dimensions (dimensions in mm [inch]) max 294 [.57] min 246 [9.68] max 248 [9.76] min 224 [8.82] max 248 [9.76] min 224 [8.82] 9. 9.2 9 [3.58] 56,5 [2.22] L A 2 5 8 4 2 [0.8] 5 [2.0] 3 [Ø0.8] 6 [0.4] 35,5 [.40] 2 x 9,5 [Ø0.374] 4 x 3 [Ø0.52] 3 3 3 0,5 F F5 G F2 7 7 L A P B X 0,0/00 [0.0004/4.0] Rzmax 4 F4 G2 F6 F3 Required surface quality of valve mounting face Nameplate 2 ype of adjustment 8 Spindle for adjusting the flow cross-section (hexagon socket 6 A/F) urning counter-clockwise = larger flow urning clockwise = smaller flow 3 hrough-bores for valve mounting 4 Identical seal rings for ports A, B, P, 5 Identical seal rings for ports X,, L 6 Locating pin (included in the sope of supply) 7 Hexagon 9 A/F, tightening torque M = 25 Nm [8.4 ft-lbs] 8 Porting pattern to ISO 440-07-07-0-05 and NFPA 3.5. R2-D07 9. Plug screw on variant B 9.2 Plug screw on variant A Valve mounting screws (separate order) Metric 4 hexagon socket head cap screws ISO 4762 - M0-0.9-flZn-240h-L 2 hexagon socket head cap screws ISO 4762 - M6-0.9-flZn-240h-L UNC 4 hexagon socket head cap screws 3/8-6 UNC 2 hexagon socket head cap screws /4-20 UNC Note! he length and tightening torque of valve mounting screws must be calculated taking account of the components mounted above and below the sandwich plate valve.
hrottle check valve ype Z2FS Size 25 Component series 3X Maximum operating pressure 350 bar [5076 psi] Maximum flow 360 l/min [95 US gpm] tb0222 able of contents Content Page Features Ordering code 2 Symbols 2 Function, section 3 echnical data 4 Characteristic curves 5 Unit dimensions 6 Features Sandwich plate valve Porting pattern to ISO 440-08-08-0-05 and NFPA 3.5. R2-D08 For limiting the flow of 2 actuator ports Adjustment element: Spindle with hexagon socket For meter-in or meter-out throttling
Ordering code Z2FS 22 8 3X * hrottle check valve, sandwich plate design Size 25 = 22 hrottle check valve, sides A and B = hrottle check valve, side A = A hrottle check valve, side B = B Adjustment element Spindle with hexagon socket = 8 Component series 30 to 39 = 3X (30 to 39: unchanged installation and connection dimensions) S = Further details in clear text Seal material No code = NBR seals V = FKM seals (other seals on request) Attention! Observe compatibility of seals with the hydraulic fluid used ( A8 3X/S) meter-in throttling on side A ( B8 3X/S) meter-in throttling on side B ( 8 3X/S) meter-in throttling on sides A and B S2 = ( A8 3X/S2) meter-out throttling on side A ( B8 3X/S2) meter-out throttling on side B ( 8 3X/S2) meter-out throttling on sides A and B Symbols ( = component side, 2 = plate side) Meter-in throttling S Meter-out throttling S2 Variant L P X L P X Variant A L P X L P X Variant B L P X L P X
Function, section Valves of type Z2FS are throttle check valves of sandwich plate design. hey are used to limit the flow of one or two actuator ports. wo throttle check valves, which are symmetrically arranged to each other, limit the flow (by means of adjustable throttle spools) in one direction and allow a free flow in the opposite direction. In the case of meter-in throttling the hydraulic fluid is fed through channel A via throttling point () to actuator A2. hrottle spool (2.) can be axially adjusted by means of spindle (3), thus allowing throttling point () to be adjusted. At the same time, the hydraulic fluid present in channel A is fed via bore (4) to spool side (5). In addition to the spring force, the applied pressure holds throttle spool (2.) in the throttling position. he hydraulic fluid returning from actuator B2 shifts throttle spool (2.2) and thus provides an unhindered flow as with a check valve. Depending on the variant ( S or S2 ) throttling can be effective on the supply or return side. Flow limitation o change the velocity of an actuator, the throttle check valve can be installed between the directional valve and the subplate. 3 5 4 2. 2.2 2 Meter-in throttling L X A P B = component side 2 = plate side
echnical data (for applications outside these parameters, please consult us!) General Weight kg [lbs] ca. 8 [7.6] Installation orientation Optional Ambient temperature range C [ F] 30 to +50 [ 22 to +22] (NBR seals) 20 to +50 [ 4 to +22] (FKM seals) Hydraulic Maximum operating pressure bar [psi] 350 [5076] Maximum flow l/min [US gpm] 360 [95] Hydraulic fluid Mineral oil (HL, HLP) to DIN 5524 ) ; fast bio-degradable hydraulic fluids to VDM 24568 (see also RE 9022); HEG (rape seed oil) ) ; HEPG (polyglycols) 2) ; HEES (synthetic esters) 2) ; other hydraulic fluids on request Hydraulic fluid temperature range C [ F] 30 to +80 [ 22 to +76] (NBR seals) 20 to +80 [ 4 to +76] (FKM seals) Viscosity range mm 2 /s [SUS] 2.8 to 380 [3 to 760] Permissible max. degree of contamination of the hydraulic fluid - cleanliness class to ISO 4406 (c) ) Suitable for NBR and FKM seals 2) Suitable for FKM seals only 3) he cleanliness classes specified for components must be adhered to in hydraulic systems. Effective filtration prevents malfunction and, at the same time, prolongs the service life of components. For the selection of filters, see data sheets RE 50070, RE 50076, RE 5008, RE 50086, RE 50087 and RE 50088. Class 20/8/5 3)
Characteristic curves (measured with HLP46, ϑ oil ( = 90 SUS) = 40 C ±5 C [04 F ± 9 F]) p-q V characteristic curves (via check valve, with closed throttle) [58] 4 Pressure differential in bar [psi] [50] [40] [30] [20] [0] [0] 3 2 0 30 60 90 20 50 80 20 240 270 300 330 360 [0] [0] [20] [30] [40] [50] [60] Flow in l/min [US gpm] [70] [80] [90] [95.] [3626] 250 p-q V characteristic curves (constant throttling position) 4 5 6 7 8 [2900] 200 9 Pressure differential in bar [psi] [275] [450] [60] [870] [580] [290] [45] [72.5] 50 00 80 60 40 20 0 5 0 2 3 5 7 hrottling position in turns [4.5] [0] 0 30 60 90 20 50 80 20 240 270 300 330 360 [0] [0] [20] [30] [40] [50] [60] Flow in l/min [US gpm] [70] [80] [90] [95.]
Unit dimensions (dimensions in mm [inch]) max 320 [2.50] min 268 [0.55] max 27,3 [0.68] min 245,3 [9.66] max 27,3 [0.68] min 245,3 [9.66] 88 [7.40] 9. 9.2 7 [4.6] 76,6 [3.02] 55 X P 4 [2.7] 2 7 5 8 4 7 2 [0.6] 6 [Ø0.24] 6 [0.50] 7,2 [0.68] 2 x 6,5 [Ø0.256] 6 x [Ø0.433] 3 2,6 F F5 G F2 L X P A B 0,0/00 [0.0004/4.0] Rzmax 4 F4 G2 F6 F3 Required surface quality of valve mounting face Nameplate 2 Adjustment element 8 Spindle for adjusting the flow cross-section (hexagon socket 6 A/F) urning counter-clockwise = greater flow urning clockwise = smaller flow 3 hrough-bores for valve mounting 4 Identical seal rings for ports A, B, P, 5 Identical seal rings for ports X,, L 6 Locating pin (included in the scope of supply) 7 Hexagon 22 A/F, tightening torque M = 25 Nm [8.4 ft-lbs] 8 Porting pattern to ISO 440-08-08-0-05 and NFPA 3.5. R2-D08 9. Plug screw for variant B 9.2 Plug screw for variant A Valve mounting screws (separate order) Metric 6 hexagon socket head cap screws ISO 4762 - M2-0.9-flZn-240h-L UNC 6 hexagon socket head cap screws 5/8- UNC Note! he length and tightening torque of valve mounting screws must be calculated taking account of the components mounted above and below the sandwich plate valve.