FIFTH WHEELS Combination Fifth Wheel and Gooseneck Hitch The FIREHAWK II was designed from the ground up provide you with the ability to haul either a fifth type trailer (RV) or a gooseneck type trailer (utility). Take out two hitch pins and remove the fifth wheel head unit and the FIREHAWK II converts from a 23,000 pound fifth wheel hitch to a 23,000 pound gooseneck hitch. 28-800-1 Complete Firehawk Hitch (A, B & C) 28-810-1 Fire Hawk Head Unit (A) 15051 28-803-1 GooseNeck Base Unit (B) 15053 28-821-1 Installation Base Plate (C) 15058 KING PINS The Buyers King Pins are forged from AISI 8630 steel and heat treated to create and maintain a hardness of 302-363 BHN (this makes them easier to weld). 19-500 2 SAE King Pin (Weld On) (Refer to Appendix) KP20038 19-KPT-809BF 2.00 X.500 KPT-809BF 19-KPT-809CF 2.00 X.250 KPT-809CF 19-KPT-809EF 2.00 X.312 KPT-809EF 19-KPT-809F 2.00 X.375 KPT-809F 19-KPT-847 3.50 X.375 KPT-847 19-KPT-847B 3.50 X.500 KPT-847B 19-KPT-880 2.00 X.375 KPT-880 19-KPT-880-1 2.00 X.375 PT-880-1 19-KPT847-BF 3.50 X.50 KPT847-BF 19-KP-0412 Mushroom Style 2 Kingpin & Housing H2KP-0412 19-KP-0413 Mushroom Style 3.5 Kingpin & Housing H2KP-0413 A-FRAMES SQUARE 0000-18-002 HB Square TW Jack 3.5 K 15 Travel A-FRAME JACKS 18-325 A- Frame Jack - Plate Not Included (5K), 14 Travel Height 19 80
A-FRAME JACKS This A-Frame Jack has a triangular mounting bracket for easy bolt-on or weld-on mounting through coupler or bracket systems. Casters or feet can easily be installed with the unique lock-in key slot. Jack mounting bolts are free with the jack, ask your Nuera Transport salesperson. 18-240 A-Frame Top Wind Jack (1K) (Refer to Appendix) 80167 18-250 A-Frame Top Wind Jack (5K) (Refer to Appendix) 80391 18-260 A-Frame Top Wind Jack (2K) (Refer to Appendix) 80401 18-260-A Replacement Handle Only 82700 18-267 A-Frame Side Wind Jack (2K), Atwood 87510 18-267-S A-Frame Side Wind Jack (2K), Shelby 5717-24 18-326 A-Frame Top Wind Jack (5K), Travel Plate Height 9 18-303-1S A-Frame Side Wind Jack (1K), 22 Plate Height 6 18-448 A-Frame Side Wind Jack (2K), 21 Plate Height 7 18-448-1 A-Frame Side Wind Jack (3K), 22.6 Plate Height 7 18-307-B A-Frame Top Wind Jack (2K) - Standard Height TJD-2000-B 18-307-LB A-Frame Top Wind Jack (2K) - 5.5 Bracket Height TJA-2001 18-309 A-Frame Top Wind Jack (5K) - Standard Height TJA-5000 Easy cranking 8 turns per inch, dependable lift and side load capacity, extra thick A-frame mounting bracket (weld-on or bolt-on), 15 of travel. 18-459 A-Frame Top Wind Jack (2K) (Refer to Appendix) 155022 18-460 A-Frame Top Wind Jack (5K) (Refer to Appendix) 175000 18-461-1 A-Frame Top Wind Jack (2K) 5.5 Bracket Height 155033 18-463 A-Frame Top Wind Jack (2K) with Steel Wheel 017125 18-308 Economy jack 2k capacity, 14 travel - 22.25 (Fulton) B1 EA2000 SWIVEL JACK 18-299-I Marine Swivel Jack with Wheel (1K) (RAM) MJ1000B 18-298 Swivel Jack and Wheel - 500 lb (Atwood) QT 87535 18-TS3000101 Kickstand and Wheel - 300 lb (Fulton) FL TS3000101 18-264 Swivel Jack and Wheel - 600 lb (Fulton) TJ 600T 18-262 Swivel Jack and Wheel - (1.5K) (Fulton) XP15-0101 18-299 Swivel Jack and Wheel - 800 lb (Fulton) TJ50J 18-263 Swivel Jack and Wheel - (1K) (Fulton) XP100101 98-90-098 Swivel Jack and Wheel - Double Wheel (1.5K) (Fulton) XPD15L 81
JACK BOTTOM SUPPORT PLATE When welded under the A-frame of the trailer tongue, this plate provides extra support to keep the jack from bending the coupler. 18-302 Bottom Support Plate (5K) (Refer to Appendix) SPB50-300 18-80560 Support Plate for A-frame Jack Tube, 1.920 Hole (1K) QT 80560 18-80570 Support Plate for A-frame Jack Tube, 2.230 Hole (2-5K) QT 80570 Easy cranking 8 turns per inch Smooth, comfortable, ergonomic design Dependable vertical and side load capacity Proven reliability for long term use at rated loads Precision fitted parts for extra stability Painted outer tube, zinc plated inner tube 18-440 2K Top Wind Jack w/bracket Mount (10 Travel) (Refer to Appendix) 151401 18-440-6 2K Top Wind Jack w/bracket Mount (15 Travel) 151421 18-445 Snap Ring Replacement Part Only 015904 18-446 L Bracket Replacement Part Only 015909 18-440-1 Top Wind Handle Kit Only 018917 18-442 1/2 Pull Pin (fits all BullDog Jacks) 018400 18-440-4 2K Sinde Wind Bracket Mount (10 Travel) 151101 92-90-190 5K Top Wind Bracket Kit 171401 19-902 Top Wind (10 Travel) (7K) QT 198100 19-904 Side Wind (10 Travel) (7K) QT 198150 19-903 Top Wind (15 Travel) (7K) QT 198200 07-19-010 Side Wind (15 Travel) (7K) QT 198250 18-440-4 Sidewind (10" Travel) (2K) B1 171101 92-90-190 Topwind (10 Travel) (5 K) B1 171401 JACK FOOT 18-311 Jack Foot - 6.2 Length 018173 18-312 Jack Foot - 2.25 Length 0180231 18-470 Jack Foot with Pin, Shelby 018564 18-F2000 Jack Foot Plate FL F2000 06-18-005 Tall Jack Foot 8.9 for 2 Tube B1 019373 18-18520 Rack Post/Foot QT 18520 18-312 Jack Foot with hardware, Cequint FP2000-0201 18-311-1 Cequent Disc Foot Hardware 4,25 X 2 RAM jack feet, with convenient "twist-lock", provide easy attachment to the jack and quick removal for towing. They mount on all Atwood A-Frame jacks and jack screws. 18-309-L Ram Jack Foot - Long (Refer to Appendix) JF-101 18-309-S Ram Jack Foot - Short (Refer to Appendix) JF-100 82
JACK FOOT 18-265 Jack Foot (1K) - Short 82650 Fits both jack number 18-260 & 18-250 (see page #57) CASTER WHEELS Atwood caster wheels, with convenient "twist-lock", provide easy attachment to the jack and quick removal for towing. They mount on all Atwood A-Frame jacks and jack screws. 18-268 Caster Wheel (1K) Fits both jack number 18-260 & 18-250 (see page #57 ) 80552 Bulldog all-steel removable jack wheel. 18-462 Steel Caster Wheel (1K) 017125 18-310 Poly Cast Wheel (750 lbs.) 017137 18-18006 Rack Post and Wheel QT 18006 18-CE5550301 6 Jack fitting 2 OD Jacks FL CE5550301 18-299-W Plastic Wheel 6 GEARBOXES Part # Item# Description Mfg. # 18-161 A Features an L-bend bracket that welds to side and bottom of tongue QT 161 18-165 B This gearbox crank welds or bolts to an A-frame tongue QT 165 GEAR AND BEARING KITS 19-914 2K Side Wind Bulldog Jack Crank and Gear Kit 500256 19-918-1 5K Side Wind Bulldog Jack Gear Kit 500106 19-918 7K Side Wind Bulldog Jack Gear Kit 500156 18-443 2K Thrust Bearing Kit 500251 18-453 5K Thrust Bearing Kit 500223 19-919 7K Thrust Bearing Kit 500224 19-906-BB Mounting Bracket Kit 19-906-PC Holding Pin, Clip and Chain 19-906-BH-1 Handle for 19-006-B 19-906-BC Top Cap for 19-906-B 19-906-BG Gear Kit for 19-906-B 19-916-B Handle for 19-907-B 19-906-BTB Bearing Thrust for 19-907-B 18-440-B 2K Top Wind Jack w/bracket Mount (10 Travel) 0091210 83
Easy cranking 8 turns per inch Smooth, comfortable, ergonomic design Dependable vertical and side load capacity Proven reliability for long term use at rated loads Precision fitted parts for extra stability Painted outer tube, zinc plated inner tube 18-440-2 2K Side Wind Jack w/pipe Mount (15 Travel) (Refer to Appendix) 158151 18-450 5K Side Wind Jack w/pipe Mount (10 Travel) (Refer to Appendix 178201 18-450-1 5K Side Wind Jack w/pipe Mount (15 Travel) (Refer to Appendix 178203 18-451 Side Wind Handle Kit Only 700056 18-440-7 Pin & Chain Assembly Replacement Part Only, 5K, 5/8 018403 18-440-8 2K Side Wind Jack w/pipe Mount (10 Travel) 158109 19-921-C Pin & Chain Assembly, 2K, 9/16 18-440-5 2K Top Wind Jack w/pipe Mount (10 Travel) (Refer to Appendix) 158451 18-440-3 2K Top Wind Jack w/pipe Mount (15 Travel) (Refer to Appendix) 158452 18-450-2 5K Top Wind Jack w/pipe Mount (10 Travel) (Refer to Appendix) 178101 18-450-3 5K Top Wind Jack w/pipe Mount (15 Travel) (Refer to Appendix) 178151 This male mounting tube is used to mount any of the Hammerblow (Bulldog) tube mount jacks. See previous page for applicable jacks. 18-444 Male Mounting Tube 015279 The picture shows both the gear box and mounting plate. You must order both part numbers if you want a complete assembly. 18-427 Gear Box Only 018191 18-426 Mounting Plate Only 018476 Smooth-cranking 4 turns per inch of travel Powerful heavy duty gear box Extra heavy duty gauge post for maximum side load strength Specially designed gusseted caster bracket for increased stability Self-lubricating grease fitting Weather resistant yellow zinc plated rack post Red oxide primer painted steel wheel and gear box 18-428 Jack Post w/poly Wheel - Only (750 lbs) 018308 18-403 Jack Post w/steel Wheel - Only - Heavy Duty (1200 lbs) 019060 18-402 Gear box - Only (Refer to Appendix) 019141 84
Welds to side and bottom of tongue. For use with rack and wheel 18-403 (see page # 84) 18-430 Weld-on Gear Box Only 018161 Atwood Bolt Swivel Jacks are designed to allow the jack tube to swing easily from its horizontal transit position to the vertical stationery position, locking securely into place with a solid ½" diameter spring-loaded pin. The bolt design of the swivel firmly holds the jack against the mounting bracket, substantially reducing the side-to-side wobble and virtually eliminating the annoying chatter during travel. Requires either mounting bracket 18-292 or 18-291 (see next section) 18-298 Atwood Side Crank, Swivel Jack w/wheel (500lbs) (Refer to Appendix) 87535 18-295 Atwood Top Crank, Swivel Jack w/wheel (500lbs) (Refer to Appendix) 80043 MOUNTING PLATES Used with Atwood Jack # s 18-295 & 18-298 (see previous section) 18-292 Atwood Weld-On Mounting Bracket 87501 18-445 Swivel Jack Snap RIng 015904 Used with Atwood Jack # s 18-295 & 18-298 (see previous section) 18-291 Atwood Bolt-On Mounting Bracket 81412 Note: May also work with other side mount jacks (i.e. 18-440 on page #59 ) ATWOOD STABILIZER JACKS - Lifts 650 lbs. / Holds 1000 lbs. - Retracted - 11.5 - Swing away storage - Jack Rod Not Included 18-281 Atwood Stabilizer Jack (17.75 Extended) 82301 18-281-1 Atwood Stabilizer Jack (21.75 Extended) 82297 18-281-JR Jack Rod for Atwood Stabilizer Jack 80480 18-281-P Jack Foot for Atwood Stabilizer Jack 18-82300 Atwood Stabilizer Jack (retracted height 11 ) QT 82300 18-282 Scissor Jack, 5K (24 Extended) 5740-24 18-282-H Handle for Scissor Jack 5740H-24 18-TJ01 Domar Stabillizer Jack Picture not available. 85