Series HB Subminiature Pushbuttons General Specifications Electrical apacity (Resistive Load) Power Level (silver): 0.1A maximum @ 30V A/ Other Ratings ontact Resistance: 50 milliohms maximum Insulation Resistance: 100 megohms minimum @ 500V ielectric Strength: 500V A minimum for 1 minute minimum Mechanical Life: 100,000 operations minimum Electrical Life: 50,000 operations minimum Nominal Operating Force: 3.43N ontact Timing: Nonshorting (break before make) Travel: Pretravel.087 (2.2mm); Overtravel.031 (0.8mm); Total Travel.118 (3.0mm) Materials & Finishes Housing: Base: Movable ontact: Stationary ontacts: ommon Terminal: End Terminals: Lamp Terminals: Environmental ata Operating Temperature Range: Humidity: Vibration: Shock: Installation Mounting Torque: ap Installation Force: Soldering Time & Temperature: Standards & ertifications UL: Glass fiber reinforced polyamide Glass fiber reinforced polyamide 25 through +50 ( 13 F through +122 F) for Illuminated 25 through +70 ( 13 F through +158 F) for Nonilluminated 90 ~ 95% humidity for 96 hours @ 40 (104 F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 0.49Nm (4.34 lb in) maximum for round mounting nut 9.8N (2.2 lbf) maximum downward force on cap Manual Soldering: See Profile A in Supplement section. File No. E44145 All models recognized at 0.1A @ 30V A/. Add /U to end of part number to order UL mark on switch. Add /UL to end of part number to order culus mark on switch. 12
Subminiature Pushbuttons Series HB istinctive haracteristics Full face and spot illumination available. Front panel relamping. hoice of super bright LEs in white, green, and blue in addition to bright red, amber, and green LEs. ompact front panel design with 9mm square or round bezel options. Rear panel threaded mounting. Behind panel depth of less than one inch. 8mm body diameter fits common size panel cutout. Latchdown feature gives indication of circuit status. Audible and tactile feedback with smooth and responsive operation. ual, sliding contacts with self-cleaning action provide contact stability, high reliability, and increased operating life. Solder lug terminals have spacing of (2.54mm) for choice of mounting. Longer normally closed terminal facilitates wiring and soldering. Molded-in terminals lock out flux, dust, and other contaminants. Matching indicators available. Actual Size 13
Series HB Subminiature Pushbuttons HB Pole 1 SPT S Shapes TYPIAL SWITH ORERING EXAMPLE 1 5 S K W01 6G ircuits 5 ON (ON) ( ) = Momentary 6 ON ON Alternate Action with Latchdown * Wire harness & cable assemblies offered only in Americas IMPORTANT: Switches are supplied without UL & culus markings unless specified. Specific models & ratings noted on General Specifications page. K Housing Black only, Super Bright LE W01 ontacts & Terminals Silver ontacts and Solder Lug Terminals* 0.1A @ 30V A/ 5 5 5F 6B 6F 6G LEs Bright Red Amber Super Bright ESRIPTION FOR TYPIAL ORERING EXAMPLE Shape SPT ON-(ON) ircuit No ode HB15SKW01-6G- Nonilluminated Nonilluminated ap Black Housing AB B B FB A B E F G Silver ontacts & Solder Lug Terminals; rated 0.1A @ 30V A/ ap Types & olors LE ap: Lens/iffuser olor Black ap/ Window for Spot Illuminated ( only) Red/ Amber/ / lear/ LE ap: Lens/iffuser olor lear/ Nonilluminated ap olors Black ( Only) Red Yellow 14
Subminiature Pushbuttons Series HB Pole SP S K W01 Model HB15 *HB16 Plunger Position ( ) = Momentary onnected Terminals Throw & Switch/Lamp Schematics Normal own Normal own Notes: Switch is marked with NO, N,, L. LE circuit is isolated and requires external power source. ON ON (ON) ON 1-3 1-2 SPT * When in latchdown position for the alternate circuit, cap position is.051 (1.3mm) above the built-in bezel..354 (9.0mm) The bezel is an integral part of the switch body. Recommended Panel Thickness:.020 ~ (0.5 ~ 5.0mm) Housing available in black only. SHAPES & PANEL UTOUT Panel utout & Mounting HOUSING.354 (9.0mm) ONTAT MATERIALS, RATINGS, & TERMINALS Silver ontacts Power Level 0.1A maximum @ 30V A/ Solder Lug (2.0).079 (1.0).039 Thk = (0.3).012 POLES & IRUITS (8.0) ia.315 1 (OM) 3 2 The bezel is an integral part of the switch body. PB Mounting (+) (-) Overtightening the mounting nut AT073 may damage the switch housing. Solder lug terminals are spaced x.200 (2.54mm x 5.08mm). This enables PB mounting which can be accomplished by elongating P board holes to.080 (2.03mm). 15
Series HB Subminiature Pushbuttons Bright AT633 Super Bright AT624G AT629B AT630F ap olors Available: AB Lens/iffuser olors Available: B B FB T-1 Bi-pin No ode LE OLORS & SPEIFIATIONS The electrical specifications shown are determined at a basic temperature of 25. LE circuit is isolated and requires external power source. Single element LE is colored in OFF state. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Black ap with Translucent Window for LE isplay Red/ Amber/ / lear Lens/ iffuser Finish: Glossy Note for Super Bright: (+) (-) ATTENTION ELETROSTATI SENSITIVE EVIES AP TYPES & OLORS olored ap for Bright LEs Finish: Glossy ap for Bright & Super Bright LEs Bright AT4052 Spot Illuminated (7.4) ia (7.4) ia Super Bright 5 5 5F 6B 6F 6G olor Red Amber Unit Forward Peak urrent I FM 30 30 25 30 30 30 ma ontinuous Forward urrent I F 20 20 20 20 20 20 ma Forward Voltage V F 1.85 2.0 2.2 3.6 3.5 3.6 V Reverse Peak Voltage V RM 5 5 5 5 5 5 V urrent Reduction Rate Above 25 I F 0.40 0.42 0.38 0.50 0.50 0.50 ma/ Ambient Temperature Range 25 ~ +50 25 ~ +50 olor odes: A Black B Red Amber E Yellow F G J lear ap olors Available: A B Black ( Only) No Lamp E AT4166 AT4031 Red Yellow Finish: Glossy only Finish: Matte F G AT4032 Nonilluminated aps AT4167 AT4035 (4.6).181 AT4036 (1.2).047 (3.0).118 Transparent olored Lens Translucent iffuser olored LE AT633 Transparent lear Lens Translucent iffuser olored LEs AT624, AT629, AT630, or AT633 (7.4) ia 16
Subminiature Pushbuttons Series HB (9.0) Sq.354 (7.4) ia (9.0) ia.354 ap Removal (1.3).051 (3.5).138 (1.3).051 (3.5).138 1. Have cap in extended position (not latchdown) for alternate action models. 2. Use the grip slots on the sides of the cap and pull it out of the switch. AT111 Lamping Tool Lamping Tool AT111 may be used to remove and replace LE. (5.3).209 TYPIAL SWITH IMENSIONS (10.0).394 (15.5).610 Latchdown Position (5.3).209 (10.0).394 (15.5).610 Latchdown Position M8P0.75 (0.5).020 M8P0.75 (0.5).020 (7.0).276 (7.0).276 Single Pole (1.0) x (2.0) Typ.039 x.079 (0.3) Typ.012 Single Pole (1.0) x (2.0) Typ.039 x.079 (0.3) Typ.012 NO N OM OM ASSEMBLY INSTRUTIONS LE Polarity & Orientation in Lamp Socket For AT624, AT629, AT630: Insert the LE with the flat opposite the black dot molded inside the switch lamp socket. For AT633: Insert the LE with the Black ot on the terminal to the right. Flat AT624 AT629 AT630 (+) Anode (+) ATTENTION ELETROSTATI SENSITIVE EVIES ( ) (+) Top View of Switch ( ) athode ( ) NO N Black ot AT633 2 3 1 2 3 1 L(+) L(+) L(-) L(-) Super Bright LEs AT624, AT629, & AT630 are electrostatic sensitive. AT110 Socket Wrench Socket Wrench AT110 may be used to tighten the mounting nut. HB15SKW01-5-B HB16KW01-5-B ap Replacement 1. Match the prongs on the cap base with the projections in the switch, at the same time aligning the spring clips on the cap with the indentations in the switch. 2. Press firmly in place. 17