Bulletin BX-4C Bell & Gossett VSC /VSCS Pumps Technical Bulletin Part of the Bell & Gossett Equipment Selection Program
VSC/VSCS Construction Materials STANDARD SEAL CONFIGURATION PART NAME STANDARD CONSTRUCTION ASTM NO. Casing Cast iron A159 Class G0 Volute cover plate (Outboard) Cast iron A159 Class G0 Volute cover plate (Inboard) Cast iron A159 Class G0 Impeller Bronze B584 Alloy C87 Shaft 18-8 Stainless A276 Type 304 Shaft Collar Bronze B16 Alloy C30 Impeller nut Bronze B16 Alloy C30 Bearing housing (radial/thrust) Cast iron A159 Glass G0 Bearing (Radial/thrust)** Grease lubricated Bearing cover (radial/thrust) Cast iron A159-70 Class G2 Gasket Cellulose fiber/sbr Lexide SV-3 Shaft seal/seat (standard) Buna/Carbon/Ceramic Type 21*** Shaft seal/seat (optional) Buna/Carbon/Ceramic Type 2 EPT/Carbon/Tungsten Carbide Type 2 STUFFING BOX CONFIGURATION PART NAME STANDARD CONSTRUCTION ASTM NO. Casing Cast iron A159 Class G0 Volute cover plate (Outboard) Cast iron A159 Class G0 Volute cover plate (Inboard) Cast iron A159 Class G0 Impeller Bronze B584 Alloy C87 Shaft Carbon steel A108 Grade 1144 Shaft sleeve 18-8 Stainless* A269 Type 304 Shaft sleeve collar Carbon Steel SAE 1018 Impeller nut Bronze B16 Alloy C30 Bearing housing (radial/thrust) Cast iron A159 Class G0 Bearing (radial/thrust)** Grease lubricated Bearing cover (radial/thrust) Cast iron A159-70 Class G2 Gasket Cellulose fiber Lexide SV-3 Shaft seal/seat Single seal (-S) Carbon/Tungsten Carbide standard Durametallic RO Wear ring (optional) Bronze B584 Alloy C93 * Bronze for 12x14x17 1 /2 ASTM B505 Alloy C93 ** Fafnir wide inner ring type (except 10x12x17, 12x14x12 1 /2 and 12x14x17 1 /2) *** Type 2 is standard on sizes 10x12x17L, 12x14x12 3 /4L and 12x14x17 1 /2L. 2
50 Hertz Performance Curves (FT) 250 1450 RPM VSC/S FLOW COVERAGE (kpa) (M) 70 50 8X10X17L 150 4X5X14 3 /4 5X6X15 1 /2 10X12X17L 12X14X17 1 /2L 30 8X8X13B 8X10X13B 10X10X13L 10X12X13L 5X5X12L 5X6X12L 6X6X12L 6X8X12L 8X8X11 3 /4L 8X10X11 3 /4L 10X12X11 3 /4L 12X14X12 3 /4L 10 50 4X4X9 1 /4L 5X5X9 3 /4B 5X6X9 3 /4B 6X6X9 3 /4 6X6X9 3 /4 6X8X9 3 /4HL 0 0 0 0 900 0 0 0 0 00 9000 0 0 0 10 30 50 70 90 30 50 70 90 900 0 0 GPM L/s m 3 /H (FT) 2900 RPM VSC/S FLOW COVERAGE (kpa) (M) 2 2 70 2 2 1 4X4X9 1 /4L 50 1 1 1 5X5X9 3 /4B 5X6X9 3 /4B 6X6X9 3 /4B 6X8X9 6X6X9 3 /4B 3 /4B 6X8X9 3 /4B 30 10 0 0 00 0 1 1 1 1 0 GPM 0 10 30 50 70 90 110 1 L/s 0 m 3 /H 3
Hertz Performance Curves (FT) 1 1150 RPM VSC/S FLOW COVERAGE (kpa) (M) 45 1 1 35 8X10X17L 30 10X12X17L 25 4X5X14 3 /4 5X6X15 1 /2 12X14X17 1 /2L 15 10 5X5X12L 5X6X12L 6X8X12L 6X8X12L 8X8X13B 8X10X13B 10X10X13L 10X12X13L 8X8X11 3 /4L 8X10X11 3 /4L 12X14X12 1 /2 12X14X12 3 /4L 5 4X4X9 1 /4L 5X5X9 3 /4B 5X6X9 3 /4B 6X6X9 3 /4 6X8X9 3 /4 6X8X9 3 /4HL 10X12X11 3 /4L 0 0 0 0 900 0 0 0 0 00 9000 0 0 0 10 30 50 70 90 30 50 70 90 900 0 0 GPM L/s m 3 /H (kpa) 0 900 (M) 90 70 (FT) 1750 RPM VSC/S FLOW COVERAGE 8X10X17L 50 4X5X14 3 /4 5X6X15 1 /2 10X12X17L 10X12X17L 12X14X17 1 /2L 30 90 5X5X12L 5X6X12L 6X6X12L 6X8X12L 8X8X13B 8X10X13B 10X10X13L 10X12X13L 12X14X12 3 /4L TOTAL HEAD 70 50 4X4X9 1 /4L 6X8X9 3 /4L 6X6X9 3 /4L 10X12X11 3 /4L 8X8X11 3 /4L 8X10X11 3 /4L 12X14X12 1 /2 5X5X9 3 /4B 5X6X9 3 /4B 90 70 10 30 6X8X9 3 /4HL 50 5 30 10 0 900 0 0 0 0 00 9000 0 0 0 10 30 50 70 90 30 50 70 90 900 0 0 GPM L/s m 3 /H 4
Hertz Performance Curves (FT) 3 RPM VSC/S FLOW COVERAGE (kpa) (M) 1 1 1 1 1 1 0 900 4X4X9 1 /4L 6X6X9 3 /4B 6X8X9 3 /4B 5X5X9 3 /4B 5X6X9 3 /4B 0 0 0 0 900 0 0 GPM 10 30 50 70 90 150 L/s 30 50 70 90 m 3 /H Useful Pump Formulas Pressure Head (Feet) x Specific Gravity = (PSI) 2.31 Head Pressure (PSI) x 2.31 = (Feet) Specific Gravity Vacuum Dynamic Suction Lift (Feet) x.883 = (Inches of Mercury) x Specific Gravity Horsepower (Brake) = GPM x Head (Feet) x Specific Gravity 39 x Pump Efficiency Horsepower GPM x Head (Feet) x Specific Gravity = (Water) 39 Efficiency = (Pump) NPSH = (Available) Horsepower (Water) x Per Cent Horsepower (Brake) Positive Factors Negative Factors Affinity Laws: Effect of change of speed or impeller diameter on centrifugal pumps. Impeller Diameter Change GPM Capacity Ft. Head BHP D2 Q2 = Q1 D1 2 H2 = ( D2 D1 ) H1 3 P2 = ( D2 D1 ) P1 Speed Change Q2 = RPM2 Q1 RPM1 H2 = ( RPM2 RPM1 2 ) H1 P2 = ( RPM2 RPM1 3 ) P1 Where Q = GPM, H = Head, P = BHP, D = Impeller Dia., RPM = Pump Speed 5
Engineering Data VSC/VSCS Series MECHANICAL SEALS SEAL FACE- CARBON SEAT INSERT- CERAMIC SEAT INSERT CUP-BUNA RETAINER-SS SPRING-STAINLESS STEEL ELASTOMER- BUNA SELECTION GUIDE Standard Size VSC/VSCS Series Type 21*, Carbon/Ceramic, Buna elastomer, 316 S.S. spring. Temperature range to 225 F (-29 to 107 C). PH limitation 7-9. Ideally suited for open or closed systems with relatively clean liquid and few abrasives. Also available in Carbon/Tungsten Carbide, EPT elastomers construction.temperature range to F (-29 to 149 C). PH limitation 7-11. VSC/VSCS-F Standard configuration pump, Type 21*, Buna elastomer, Carbon/Ceramic seal supplied with an external flush to the seal faces. Temperature range to 225 F (-29 to 107 C), PH limitation 7-9. Best suited for fluid environments containing moderate amounts of abrasives. Ideal for cooling tower applications. VSC/VSCS-S Stuffing box configuration pump utilizes a Durametallic RO, Carbon/Tungsten Carbide with an external flush to the seal faces. Elastomers are EPR (ethylene propylene rubber) and wetted metal parts 316 S.S. Temperature range to F** (-29 to 149 C), PH limitations 7-11. For use on open or closed systems where temperature or pressure requirements exceed the limits of the standard Type 21 seal. NOTE: Refer to product submittals for individual temperature and pressure capabilities. * Type 2 is standard on sizes 10x12x17L, 12x14x12 3 /4L and 12x14x17 1 /2L (Type 2 shown in diagram). ** For operating temperatures above 250 F (121 C) a cooled flush is recommended for optimum seal life. On closed systems cooling is accomplished by inserting a small heat exchanger in the flush line to cool the seal flushing liquid. Flush-line Filters and Sediment Separators are available on special request. 6
Engineering Data VSC/VSCS Series ALLOWABLE STATIC FLANGE LOADINGS The orientation of the nozzles on the VSC/VSCS Series Pumps permits static loads which can be supported without impairing pump operation. The following schedule gives the maximum vertical static forces (downward) which we know from experience and judgment can be tolerated. F F FORCE (F) IN POUNDS ON VSC PUMPS VSCS PUMPS EACH VERTICAL FLANGE 4x4x9 1 /4L 2,000 (8,896) 5x5x9 3 /4B 5x6x9 3 /4B 2,750 (12,232) 5x5x12B & L 54x5x12B & L 2, (9,786) 6x6x9 3 /4B & L 6x8x9 3 /4B & L 3, (14,678) 6x8x9 3 /4H & HL 6x8x9 3 /4H & HL 4, (21,350) 6x6x12L 6x8x12L 3, (16,013) 8x8x10 1 /2 8x10x10 1 /2 5,000 (22,2) 8x8x13B 8x10x13B 5,000 (22,2) 4x5x14 3 /4 2,900 (12,899) 5x6x15 1 /2 4,000 (17,792) 10x10x13B & L 10x12x13B & L 6, (27,578) 8x10x17L 5, (25,354) 10x12x11 & 11 3 /4L 7, (33,3) 10x12x17 & L 6, (30,246) 12x14x12 1 /2 8, (36,029) 12x14x12 3 /4L 8, (36,029) 12x14x17 1 /2B & L 9,000 (,032) VSC a. The VSC Series Pumps must be installed, with the baseplate completely grouted in accordance with Bell & Gossett and Hydraulic Institute Standards. b. No external moments or transverse forces should be applied to the nozzles of the VSC/VSCS Series Pumps. Should the schedule of maximum vertical static forces (F) be exceeded, or the above limitations not be considered, malfunction of the pump and shorter life of the wearing parts will occur. 7
VSC/VSCS Series FLOOR SPACE SAVINGS FOR A VSC/VSCS PUMP AS COMPARED TO A HORIZONTAL SPLIT CASE PUMP. 4 4 2 2 1 3 5 VSC pumps eliminate the cost of all piping shown in red which is required for conventional single-stage, double suction pumps. 5 1 3 ESTIMATED ADDITIONAL INSTALLED COSTS FOR HORIZONTAL SPLIT CASE SINGLE-STAGE DOUBLE-SUCTION PUMPS ITEM DESCRIPTION 4" PIPE 6" PIPE 8" PIPE 10" PIPE 1 Two 90 long radius $ 24.00 $ 62.00 $ 115.00 $ 7.00 butt weld elbows 2 Four welding neck flanges 71.00 107.00 199.00 311.00 3 Materials for fabricating 14.00 17.00 24.00 38.00 two pipe supports 4 Time for welding four 8 hrs 9.6 hrs 12.6 hrs 15.8 hrs flanges to elbows, gapping and setting flange 5 Time for locating and 1.9 hrs 2.1 hrs 2.6 hrs 2.8 hrs welding two pipe supports; positioning and bolting two elbow assemblies. 6 Total labor time 10 hrs 11.7 hrs 15.2 hrs 18.6 hrs 7 Labor @ $35.00 per hr $350.00 $9.00 $532.00 $651.00 8 Total estimated $459.00 $595.00 $870.00 $17.00 additional installed cost over B&G VSC Pump FLOOR SPACE SAVED WITH B&G VSC PUMPS AREA AREA FOR SAVED CONVEN- AREA FOR WITH PIPE TIONAL VSC VSC SIZE PUMPS PUMPS PUMPS 4" 16 sq. ft. 10 sq. ft. 6 sq. ft. 1.5 sq. m 1.0 sq. m.6 sq. m 6" 19 sq. ft. 12 sq. ft. 7 sq. ft. 1.8 sq. m 1.1 sq. m.7 sq. m 8" 24 sq. ft. 15 sq. ft. 9 sq. ft. 2.2 sq. m 1.4 sq. m.8 sq. m 10" 32 sq. ft. sq. ft. 12 sq. ft. 3.0 sq. m 1.9 sq. m 1.1 sq. m COST SAVINGS IN FLOOR SPACE WITH B&G VSC PUMPS AVERAGE SAVINGS WITH FLOOR SPACE VSC PUMPS PIPE SAVED WITH $.00* PER SIZE VSC PUMPS SQ. FT. 4" 6 sq. ft. $4.00.6 sq. m 6" 7 sq. ft. 5.00.7 sq. m 8" 9 sq. ft. 7.00.8 sq. m 10" 12 sq. ft. 9.00 1.1 sq. m The above estimated additional installed costs for conventional single-stage, double-suction pumps are conservative. Actual cost differentials will depend upon locale and piping practices employed. 1994 Price of Labor Estimated * Based on average construction costs per sq. ft. of various buildings as supplied by Dodge Construction Statistic for 1994. 8
DIMENSIONS Dimensions subject to change without notice. Do not use for construction purposes. NOTE: Flanges are 125# ANSI Standard. Optional 250# ANSI rating is available. DISCHARGE Z S SUCTION S Z DISCHARGE CP HC Right hand rotation is furnished unless otherwise specified. HO HD HA Viewed From Pump End HA HB LEFT HAND ROTATION RIGHT HAND ROTATION PUMP END MOTOR END STANDARD MECHANICAL SEAL CONSTRUCTION STUFFING BOX CONSTRUCTION PUMP MODEL VSC, VSC-F VSC-PF, VSC-S & VSC-D PUMP MOTOR DIMENSIONS IN INCHES (MM) DIMENSIONS IN INCHES (MM) SIZE FRAME CP HA HB HC MAX. HD HO S Z CP HA HB HC MAX. HD HO S Z 182T-184T 1 /8(1019) 38 1 /4(972) 46 3 /8(1178) 4x4x9 1 /4L 213T-215T 19(483) 19 1 /2(495) 38 1 /4(972) 43 3 /8(1102) 13 1 /4(337) 22 3 /4(578) 6(152) 6(152) 25 1 /4(641) 19 1 /2(495) 43 3 /8(1102) 49 5 /8(12) 13 1 /4(337) 22 3 /4(578) 6(152) 6(152) 254T-256T 43 3 /8(1102) 48 1 /8(1222) 49 5 /8(12) 54 3 /8(1381) 254T-256T 43 3 /8(1102) 49 7 /8(1267) 56 1 /8(1426) 284TS-286TS 50 3 /4(1289) 13 1 /4(337) 22 3 /4(578) 57(1448) 13 1 /4(337) 22 3 /4(578) 4x4x9 1 /4L 324TS-326TS 19 1 /2(495) 49 5 /8(12) 54 1 /8(1375) 14 1 /4(362) 23 3 /4(3) 3 /8(1534) 14 1 /4(362) 23 3 /4(3) 19(483) 6(152) 6(152) 25 1 /4(641) 19 1 /2(495) 49 5 /8(12) 3 RPM 364TS-365TS 56 3 /8(1432) 15 1 /4(387) 24 3 /4(629) 62 5 /8(1591) 15 1 /4(387) 24 3 /4(629) 6(152) 6(152) 4TS 58 5 /8(1489) 14(356) 23 1 /2(597) 64 7 /8(1648) 14(356) 23 1 /2(597) 444TS 26(6) 64 1 /2(1638) 18(457) 27 1 /2(699) 26(6) 70 3 /4(1797) 18(457) 27 1 /2(699) 182T-184T 1 /8(1019) 38 1 /4(972) 46 3 /8(1178) 5x5x9 3 /4B 213T-215T 19(483) 19 1 /2(495) 38 1 /4(972) 43 3 /8(1102) 13 1 /4(337) 23 3 /4(3) 7 1 /4(184) 7 1 /4(184) 25 1 /4(641) 19 1 /2(495) 43 3 /8(1102) 49 5 /8(12) 13 1 /4(337) 23 3 /4(3) 7 1 /4(184) 7 1 /4(184) 254T-256T 43 3 /8(1102) 49 7 /8(1267) 49 5 /8(12) 56 1 /8(1426) 284TS 49 1 /4(1251) 55 1 /2(1410) 286TS 50 3 /4(1289) 13 1 /4(337) 23 3 /4(3) 57(1448) 13 1 /4(337) 23 3 /4(3) 324TS 52 5 /8(1337) 58 7 /8(1495) 14 1 /4(362) 24 3 /4(629) 14 1 /4(362) 24 3 /4(629) 5x5x9 3 /4B 326TS 19 1 /2(495) 49 5 /8(12) 54 1 /8(1375) 3 /8(1534) 19(483) 7 1 /4(184) 7 1 /4(184) 25 1 /4(641) 19 1 /2(495) 49 5 /8(12) 3550 RPM 364TS 55 3 /4(1416) 62(1575) 7 1 /4(184) 7 1 /4(184) 365TS 56 3 /8(1432) 15 1 /4(387) 25 3 /4(654) 62 5 /8(1591) 15 1 /4(387) 25 3 /4(654) 4TS-5TS 58 5 /8(1489) 14(356) 24 1 /2(622) 64 7 /8(1648) 14(356) 24 1 /2(622) 444TS 26(6) 64 1 /2(1638) 18(457) 28 1 /2(724) 26(6) 70 3 /4(1797) 18(457) 28 1 /2(724) 213T-215T 38 1 /4(972) 43 3 /8(1102) 49 5 /8(12) 43 3 /8(1102) 5x5x12B 254T-256T 43 3 /8(1102) 49 7 /8(1267) 13 1 /4(337) 24 3 /4(629) 56 1 /8(1426) 19(483) 19 1 /2(495) 8(3) 8(3) 25 1 /4(641) 19 1 /2(495) 5x5x12L 284T-286T 52 1 /8(1324) 58 3 /8(1483) 13 1 /4(337) 24 3 /4(629) 8(3) 8(3) 324T-326T 49 5 /8(12) 55 5 /8(1413) 14 1 /4(362) 25 3 /4(654) 49 5 /8(12) 61 7 /8(1572) 14 1 /4(362) 25 3 /4(654) 213T-215T 48 1 /8(1222) 55 3 /8(17) 55 3 /4(1416) 6x6x9 3 /4B 254T-256T 53 5 /8(1362) 61 1 /4(1556) 22 3 /4(578) 26(6) 15 1 /2(394) 27(686) 8(3) 8(3) 30 3 /8(772) 26(6) 6x6x9 3 /4L 284T-286T 55 7 /8(1419) 63 1 /2(1613) 15 1 /2(394) 27(686) 8(3) 8(3) 324T 58(1473) 65 5 /8(1667) 286TS 54 1 /2(1384) 62 1 /8(1578) 324TS 56 3 /8(1432) 15 1 /2(394) 27(686) 64(1626) 15 1 /2(394) 27(686) 326TS 57 7 /8(1470) 65 1 /2(1664) 6x6x9 3 /4B 364TS 26(6) 59 1 /2(1511) 26(6) 67 1 /8(1705) 22 3 /4(578) 16(6) 27 1 /2(699) 8(3) 8(3) 30 3 /8(772) 3550 RPM 365TS 1 /8(1527) 67 3 /4(1721) 16(6) 27 1 /2(699) 8(3) 8(3) 4TS 62 3 /8(1584) 70(1778) 17(432) 28 1 /2(724) 5TS 63 7 /8(1622) 71 1 /2(1816) 17(432) 28 1 /2(724) 444TS 32(813) 71(13) 68 1 /4(1734) (508) 31 1 /2() 32(813) 71(13) 75 7 /8(1927) (508) 31 1 /2() 213T-215T 47 1 /8(1197) 54 1 /8(1375) 6x8x9 3 /4H 254T-256T 52 5 /8(1337) 59 5 /8(1514) 21 3 /4(552) 26(6) 15 1 /2(394) 28(711) 8 1 /4(210) 8 1 /4(210) 28 11 /16(729) 26(6) 6x8x9 3 /4HL 284T-286T 54 7 /8(1394) 61 3 /4(1568) 15 1 /2(394) 28(711) 8 1 /4(210) 8 1 /4(210) 324T-326T 58 3 /8(1483) 65 3 /8(1661) 215T 48 1 /8(1222) 55 3 /4(1416) 254T-256T 53 5 /8(1362) 61 1 /4(1556) 15 1 /2(394) 28(711) 15 1 /2(394) 28(711) 6x6x12L 284T-286T 22 3 /4(578) 26(6) 55 7 /8(1419) 8 3 /4(222) 8 3 /4(222) 30 3 /8(772) 26(6) 63 1 /2(1613) 8 3 /4(222) 8 3 /4(222) 324T-326T 59 3 /8(1508) 67(1702) 364TS 59 1 /2(1511) 16(6) 28 1 /2(724) 67 1 /8(1705) 16(6) 28 1 /2(724) 254T-256T 54 7 /8(1394) 62 1 /2(1588) 8x8x10 1 /2 284T-286T 57(1448)) 15 1 /2(394) 29 1 /2(749) 64 5 /8(1641) 15 1 /2(394) 29 1 /2(749) 23 15 /16(8) 26(6) 8 1 /2(216) 8 1 /2(216) 31 9 /16(2) 26(6) 8x8x11 3 /4L 324T-326T 5 /8(15) 68 1 /4(1734) 8 1 /2(216) 8 1 /2(216) 364TS-365TS 61 1 /4(1556) 16(6) 30(762) 68 7 /8(1749) 16(6) 30(762) 256T 54 7 /8(1394) 62 1 /2(1588) 284T-286T 57(1448) 64 5 /8(1641) 8x8x13B 324T-326T 23 15 /16(8) 26(6) 5 /8(15) 17(432) 31(787) 9 1 /2(241) 9 1 /2(241) 31 9 /16(2) 26(6) 68 1 /4(1734) 17(432) 31(787) 9 1 /2(241) 9 1 /2(241) 364TS-365TS 61 3 /8(1559) 69(1753) 4TS 63 5 /8(1616) 71 1 /4(1810) 286T 1 /2(1537) 68 3 /4(1746) 324T-326T 64(1626) 72 1 /4(1835) 10x10x13 364T-365T 64 3 /4(1645) 75 1 /8(1908) 27 3 /8(695) 32(813) 71(13) (508) 37(9) 11(279) 11(279) 35 5 /8(905) 32(813) 71(13) 10x10x13L 364TS-365TS 68 1 /2(17) 73(1854) (508) 37(9) 11(279) 11(279) 4TS-5TS 74 7 /8(1902) 76 3 /4(1949) 444TS-445TS 66 7 /8(1699) 83 1 /8(2111) 9
DIMENSIONS Discharge NOTE: Flanges are 125# ANSI Standard. Optional 250# ANSI rating is available. Z Dimensions subject to change without notice. Do not use for construction purposes. YY Z YY Discharge HC CP Right hand rotation is furnished unless otherwise specified. S Suction S HO HD HA LEFT HAND ROTATION Viewed From Pump End HA RIGHT HAND ROTATION STANDARD MECHANICAL SEAL CONSTRUCTION STUFFING BOX CONSTRUCTION PUMP MODEL VSCS, VSCS-F VSCS-PF, VSCS-S & VSCS-D PUMP MOTOR DIMENSIONS IN INCHES (MM) DIMENSIONS IN INCHES (MM) SIZE FRAME CP HA HB HC MAX. HD HO S YY Z CP HA HB HC MAX HD HO S YY Z 254T-256T 55 5 /8(1413) 61 1 /4(1556) 284T-286T 55 7 /8(1419) 63 1 /2(1613) 4x5x14 3 /4 324T-326T 22 3 /4(578) 26(6) 59 3 /8(1508) 17(432) 30(762) 6(152) 15(381) 9(229) 30 3 /8(772) 26(6) 67(1702) 17(432) 30(762) 6(152) 15(381) 9(229) 364TS-365TS 1 /8(1527) 67 3 /4(1721) 4TST 62 3 /8(1584) 70(1778) 182T-184T 1 /8(1019) 38 1 /4(972) 46 3 /8(1178) 38 1 /4(972) 5x6x9 3 /4B 213T-215T 19(483) 19 1 /2(495) 43 3 /8(1102) 13 1 /4(337) 23 3 /4(3) 3(76) 13(330) 7 1 /4(184) 25 1 /4(641) 19 1 /2(495) 43 3 /8(1102) 49 5 /8(12) 13 1 /4(337) 23 3 /4(3) 3(76) 13(330) 7 1 /4(184) 254T-256T 43 3 /8(1102) 49 7 /8(1267) 49 5 /8(12) 56 1 /8(1426) PUMP END 284TS 49 1 /4(1251) 55 1 /2(1410) 286TS 50 3 /4(1289) 13 1 /4(337) 23 3 /4(3) 57(1448) 13 1 /4(337) 23 3 /4(3) 5x6x9 3 /4B 324TS 52 5 /8(1337) 57 7 /8(1470) 3550 RPM 326TS 19(483) 19 1 /2(495) 49 5 /8(12) 54 1 /8(1375) 14 1 /4(362) 24 3 /4(629) 3(76) 13(330) 7 1 /4(184) 25 1 /4(641) 19 1 /2(495) 49 5 /8(12) 3 /8(1533) 14 1 /4(362) 24 3 /8(619) 3(76) 13(330) 7 1 /4(184) 5x6x12B 5x6x12L 5x6x15 1 /2 364TS 55 3 /4(1416) 62(1575) 365TS 56 3 /8(1432) 15 1 /4(387) 25 3 /4(654) 62 5 /8(1591) 15 1 /4(387) 25 3 /4(654) 4TS 58 5 /8(1489) 14(356) 24 1 /2(622) 64 7 /8(1648) 14(356) 24 1 /2(622) 213T-215T 38 1 /4(968) 43 3 /8(1102) 43 3 /8(1102) 49 5 /8(12) 254T-256T 43 3 /8(1102) 49 7 /8(1267) 13 1 /4(337) 24 3 /4(629) 56 1 /8(1426) 13 1 /4(337) 24 3 /4(629) 19(483) 19 1 /2(495) 2(51) 12 7 /8(327) 8(3) 25 1 /4(641) 19 1 /2(495) 284T-286T 52 1 /8(1324) 49 5 /8(12) 58 3 /8(1483) 49 5 /8(12) 324T-326T 55 5 /8(1413) 14 1 /4(362) 25 3 /4(654) 61 7 /8(1572) 14 1 /4(362) 25 3 /4(654) 254T-256T 54 7 /8(1394) 62 1 /2(1588) 284T-286T 57(1448) 64 5 /8(1641) 324T-326T 26(6) 5 /8(15) 17(432) 30(762) 26(6) 68 1 /4(1734) 17(432) 30(762) 364TS-365TS 23 15 /16(8) 61 3 /8(1559) 4 9 /16(116) 17 3 /4(451) 10 1 /2(267) 31 9 /16(2) 69(1753) 4TS 65 1 /8(1654) 72 3 /4(1848) 5TS-444TS 32(813) 71(13) 69 1 /2(1765) (508) 33(838) 32(813) 71(13) 77 1 /8(1559) (508) 33(838) 213T-215T 48 1 /8(1222) 55 3 /4(1416) HB MOTOR END 2(51) 12 7 /8(327) 8(3) 4 9 /16(116) 17 3 /4(451) 10 1 /2(267) 6x8x9 3 /4B 254T-256T 53 5 /8(1362) 61 1 /4(1556) 6x8x9 3 /4L 284T-286T 22 3 /4(578) 26(6) 55 7 /8(1419) 15 1 /2(394) 27(686) 3(76) 15(381) 8(3) 30 3 /8(772) 26(6) 63 1 /2(1613) 15 1 /2(394) 27(686) 3(76) 15(381) 8(3) 324T 58(1473) 65 5 /8(1667) 286TS 54 1 /2(1384) 62 1 /8(1578) 324TS 56 3 /8(1432) 15 1 /2(394) 27(656) 64(1626) 15 1 /2(394) 27(686) 326TS 57 7 /8(1470) 65 1 /2(1664) 6x8x9 3 /4B 364TS 26(6) 59 1 /2(1511) 26(6) 67 1 /8(1705) 22 3 /4(578) 16(6) 27 1 /2(699) 3(76) 15(381) 8(3) 30 3 /8(772) 16(6) 27 1 /2(699) 3(76) 15(381) 8(3) 3550 RPM 365TS 1 /8(1527) 67 3 /4(1721) 4TS 62 3 /8(1584) 70(1778) 5TS 63 7 /8(1622) 17(432) 28 1 /2(724) 71 1 /2(1816) 17(432) 28 1 /2(724) 444TS 32(813) 71(13) 68 1 /4(1734) (508) 31 1 /2() 32(813) 71(13) 75 7 /8(1927) (508) 31 1 /2() 213T-215T 47 1 /8(1197) 54 1 /8(1375) 6x8x9 3 /4H 254T-256T 52 5 /8(1337) 59 5 /8(1514) 6x8x9 3 /4HL 284T-286T 21 3 /4(552) 26(6) 54 7 /8(1394) 15 1 /2(394) 28(711) 5(127) 16(6) 8 1 /4(210) 28 11 /16(729) 26(6) 61 3 /4(1568) 15 1 /2(394) 28(711) 5(127) 16(6) 8 1 /4(210) 324T-326T 58 3 /8(1483) 65 3 /8(1661) 215T 48 1 /8(1222) 55 3 /4(1416) 254T-256T 53 5 /8(1362) 61 1 /4(1556) 6x8x12L 284T-286T 22 3 /4(578) 26(6) 55 7 /8(1419) 15 1 /2(394) 28(711) 2 1 /2(64) 15(381) 8 3 /4(222) 30 3 /8(772) 26(6) 63 1 /2(1613) 15 1 /2(394) 28(711) 2 1 /2(64) 15(381) 8 3 /4(222) 324T-326T 59 3 /8(1508) 67(1702) 364TS 59 1 /2(1511) 16(6) 67 1 /8(1705) 16(6) 28 1 /2(724) 254T-256T 54 7 /8(1394) 62 1 /2(1588) 8x10x10 1 /2 284T-286T 57(1448) 15 1 /2(394) 29 1 /2(749) 64 5 /8(1641) 15 1 /2(394) 29 1 /2(749) 23 15 /16(8) 26(6) 4 1 /2(114) 17(432) 8 1 /2(216) 31 9 /16(2) 26(6) 8x10x11 3 /4L 324T-326T 5 /8(15) 68 1 /4(1734) 364TS-365TS 61 1 /4(1556) 16(6) 30(762) 68 7 /8(1749) 16(6) 30(762) 256T 54 7 /8(1394) 62 1 /2(1588) 4 1 /2(114) 17(432) 8 1 /2(216) 284T-286T 57(1448) 64 5 /8(1641) 8x10x13B 324T-326T 23 15 /16(8) 26(6) 5 /8(15) 17(432) 31(787) 5 1 /2(1) 17(432) 9 1 /2(241) 31 9 /16(2) 26(6) 69 1 /4(1759) 17(932) 31(787) 5 1 /2(1) 17(432) 9 1 /2(241) 364TS-365TS 61 3 /8(1559) 69(1753) 10x12x11 10x12x11 3 /4L 4TS 63 5 /8(1616) 71 1 /4(1810) 256T 54 7 /8(1394) 62 1 /2(1588) 284T-286T 57(1448) 64 5 /8(1641) 324T-326T 23 15 /16(8) 26(6) 5 /8(15) 18 1 /2(470) 34 1 /2(876) 4 1 /2(114) 18(457) 10(254) 31 9 /16(2) 26(6) 68 1 /4(1734) 18 1 /2(470) 34 1 /2(876) 4 1 /2(114) 18(457) 10(254) 364TS-365TS 61 3 /8(1559) 69(1753) 4TS-5TS 65 1 /8(1654) 72 3 /4(1848) 286T 1 /2(1537) 68 3 /4(1746) 324T-326T 64(1626) 72 1 /4(1835) 10x12x13 364T-365T 66 7 /8(1699) 75 1 /8(1908) 10x12x13L 364TS-365TS 27 3 /8(695) 32(813) 71(13) 64 3 /4(1645) (508) 37(9) 6 1 /2(165) 21(533) 11(279) 35 5 /8(905) 32(813) 71(13) 73(1854) (508) 37(9) 6 1 /2(165) 21(533) 11(279) 4TS-5TS 68 1 /2(17) 76 3 /4(1949) 444TS-445TS 74 7 /8(1902) 83 1 /8(2111) 10
DIMENSIONS NOTE: Flanges are 125# ANSI Standard. Discharge Optional 250# ANSI rating is available. Z Dimensions subject to change without notice. Do not use for construction purposes. YY Z YY Discharge HC CP Right hand rotation is furnished unless otherwise specified. S Suction S HO HD HA LEFT HAND ROTATION Viewed From Pump End HA RIGHT HAND ROTATION PUMP MOTOR DIMENSIONS IN INCHES (MM) SIZE FRAME CP HA HB HC MAX. HD HO S YY Z 284T-286T 64 5 /8(1641) 324T-326T 68 1 /4(1734) 8x10x17 364T-365T 31 9 /16 32 71 71 1 /8(17) 39 5 1 /2 21 11 7 /8 Stuffing Box Only 364TS-365TS (2) (813) (13) 69(1753) (508) (991) (1) (533) (302) 4TS-5TS 72 3 /4(1848) 444TS-445TS 79 1 /8(10) 286T 57(1448) 324T-326T 5 /8(15) 8x10x17L 364T-365T 63 1 /2(1613) 23 15 /16 32 71 39 5 1 Standard Mechanical 365TS 61 3 /2 21 11 7 /8 /8(1559) (8) (813) (13) (508) (991) (1) (533) (302) Seal Only 4T-5T 65 1 /8(1554) 4TS-5TS 71 1 /2(1816) 444TS-445TS 68 1 /8(1730) 326T 72 3 /4(1848) 364T-365T 75 5 /8(1921) 4T-5T 32 71 1 /4(38) 21 1 /2 1 /2 444T (813) (13) 85 3 /8(2169) (546) (1029) 10x12x17 4TS-5TS 36 1 /8 77 1 /4(1962) 7 21 12 3 /16 Stuffing Box Only 444TS-445TS (918) 83 5 /8(2124) (178) (533) (310) 250 HP 1 RPM 36 HP (914) Consult Factory 1 RPM 326T 65 3 /4(1670) 364T-365T 68 5 /8(1743) 4T-5T 32 71 73 1 /4(1861) 21 1 /2 1 /2 10x12x17L 444T 29 1 /8 (813) (13) 78 3 /8(1991) (546) (1029) Standard Mechanical 7 21 12 3 4TS-5TS (7) 70 1 /16 /4(1784) Seal Only (178) (533) (310) 444TS-445TS 76 5 /8(1946) 250 HP and Larger 36(914) Consult Factory 284T-286T 69 1 /4(1759) 324T-326T 72 3 /4(1848) 12x14x12 1 /2 36 1 /8 32 71 21 1 364TS-365TS 73 1 /2 39 1 /2 6 3 /4 21 10 7 /8 /2(1867) Stuffing Box Only (918) (813) (13) (546) (3) (171) (533) (276) 4TS-5TS 77 1 /4(1962) 444TS-445TS 83 5 /8(2124) 324T-326T 65 3 /4(1670) 364T-365T 68 5 /8(1743) 4T 32 71 71 3 /4(1822) 21 1 /2 39 1 /2 12x14x12 3 /4L 364TS-365TS 29 1 /8 (813) (13) 66 1 /2(1689) (546) (3) Standard Mechanical 6 3 4TS-5TS (7) 70 1 /4 18 10 7 /8 /4(1784) Seal Only (171) (457) (276) 444TS-445TS 76 5 /8(1946) 250 HP and Larger 36 (914) Consult Factory 365T 81 1 /4(63) 4T-5T 81 85 7 /8(2181) 23 1 /2 45 1 /4 444T-445T (57) 93(2362) (597) (1149) 445TS 89 1 /4(2267) 250 HP 12x14x17 1 /2 1 RPM (Not available in HP 41 3 /4 36 7 3 /4 25 13 1 /2 PF Construction) 1 RPM (10) (914) (197) (635) (343) Stuffing Box Only 350 HP 1 RPM Consult Factory HP 1 RPM 450 HP 1 RPM 365T 73 1 /2(1867) 32(813) 71(3) 12x14x17 1 /2B 4T-5T 78 1 /8(1984) 23 1 /2 45 1 /4 12x14x17 1 /2L 444T-445T 34 85 1 /4(2165) (597) (1149) 7 3 /4 25 13 1 /2 36(914) 81(57) Standard Mechanical 444TS-445TS (864) 81 1 /2(70) (197) (635) (343) Seal Only 250 HP and Larger 36(914) Consult Factory PUMP END HB MOTOR END 11