mb cdef Instlltion Instructions Conversion to 16-inch tyres nd 7 1/2 J _ 16 H 2 ET 40 disk wheel 40.11 Model 124 Excluding vehicles with specil bodywork, sedns with long wheelbse nd 124.031/036/051/091/290/393. All the work described in sections A, B, C, D, nd E must be crried out in full before the wheel/tyre combintion my be used. The instlltion instructions re divided up into the following sections: A. Permitted tyre combintions B. Detching the stndrd wheels C. Modifictions to the body D. Fitting the specil wheels E. Correction of tyre infltion pressure F. Technicl detils G. Informtion for ordering replcement prts An entry in the vehicle documents is required in the Federl Republic of Germny. For this copy of the respective smple report must be submitted to the TÜV/TÜA. Copyright DimlerChrysler AG 08.12.2004 CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 1
A. Permitted tyre combintions Model Front xle Rer xle Comments 124.02/030/04/050 124.12/13 124.226/230 124.330/333 124.08/090 124.18/19 205/55 R 16 205/55 R 16 All Sedns, Coupés, (including 4MATIC, excluding 24 V) 205/55 R 16 225/50 R 16 All T-Sedns (excluding 4MATIC nd 24 V) B. Detching the stndrd wheels 1 Remove wheel covers on steel disk wheels. 2 Slcken wheel bolts. 3 Rise vehicle. 4 Unscrew wheel bolts. When unscrewing the finl wheel bolt be sure tht the wheel does not suddenly tilt off the hub. 5 Remove wheel. M Five of the stndrd wheel bolts removed must be retined for the spre wheel. C. Modifictions to the body 1 Adjusting the front fender Copyright DimlerChrysler AG 08.12.2004 CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 2
1.1 Detch side pnel on the front fender from the fixing elements, pull to the rer nd remove. 1.2 Unscrew bolts (A nd B) on fender. 1.3 Slcken bolt (A) on side of bumper. Copyright DimlerChrysler AG 08.12.2004 CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 3
1.4 Press the side prt of the bumper downwrds nd unscrew the bolts for fender fixing (A nd B). Clmp spcer between fender nd body on the left nd the right. The bore holes must lign to permit troublefree fixing. 1.5 Plce one spcer on the left nd right between the fender nd body in the side re of the bumper. 1.6 Tighten ll bolts slightly in ccordnce with lyout. Tighten bolts fter visul inspection. 2 Reworking the body t the front fenders Copyright DimlerChrysler AG 08.12.2004 CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 4
2.1 Flttening down front fender flnge: When converting to wider wheels nd tyres the inside edges of the front fender must be flttened down to n ngle of 110 over the complete wheel cutout. 2.2 If excessive PVC underbody protection hs been pplied, grind off excess before folding bck the fender flnge. 2.3 Using hot ir gun crefully het up outer edges of fender to mximum of 70-80 C. Do not overhet pint whilst pplying het (mx. 80 C). 2.4 In the mrked re (A), the fender flnge is flttened down up to the inside of the fender in severl stges. A plstic hmmer must be used to void dmging the pint. 2.5 Allow front fender flre to curve smoothly bck towrds originl, unflred line within the mrked re (B). Rectify ny dmge to pint or underbody protection. 2.6 Grind off side pnel to mtch the reworked fender contour nd ssemble. 3 Folding bck the edge of rer fender Copyright DimlerChrysler AG 08.12.2004 CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 5
3.1 If excessive PVC underbody protection hs been pplied, grind off excess before folding bck the edge of the fender. 3.2 Using hot ir gun crefully het up outer edges of fender to mximum of 70-80 C. Do not overhet pint whilst pplying het (mx. 80 C). 3.3 In the mrked re (A), the edge of the fender is flttened down s fr s the inside of the fender in severl stges. A plstic hmmer must be used to void dmging the pint. Rectify ny dmge to pint or underbody protection. 3.4 Tret wheel rch gin with underbody protection. Spry the folded bck fender edges with body cvity preserver. D. Fitting the specil wheels Copyright DimlerChrysler AG 08.12.2004 CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 6
1 Screw in centering bolts (tool kit) in upper tpped hole of the wheel hub. 2 Put on AMG light lloy wheel nd press onto wheel hub. 3 Screw in wheel bolts nd tighten positively. The wheel bolts must be dry nd free from grese. Ensure tht the wheels re not tensioned by tightening the wheel bolts on one side. (Tighten wheel bolts digonlly in severl stges). M Only M12 x 1.5 x 40 mm sphericl collr bolts supplied with the rims re to be used for the wheel fixing. 4 Unscrew centering bolt nd replce by wheel bolt. 5 Lower vehicle. 6 Evenly tighten wheel bolts digonlly to tightening torque of 110 Nm. M AMG light lloy wheel bolts must be retightened fter 100-500 km. (Tightening torque 110 Nm). Fitting snow chins is not permitted. E. Correction of tyre infltion pressure The minimum tyre infltion pressures required cn be obtined from the tyre infltion pressure tble (ppendix). The front xle or rer xle tyre infltion pressures determined re to be noted on the AMG sticker using wterproof felt tip pen. Attch sticker to suitble point on the loding edge of luggge comprtment. Copyright DimlerChrysler AG 08.12.2004 CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 7
F. Technicl detils Mnufcturer: AMG/RUOTE OZ Model: C 7 40 0119 Wheel size: 7 1/2 J _ 16 H 2 Offset: Pitch circle: Permitted wheel lod: Centering: Type: 40 mm d=112 mm, 5 hole 615 kg t rdyn=307 mm Centrl centering d=66.5+0.1 One-piece light lloy wheel with double hump Mrking: Outer side of wheel: AMG Germny C 7 40 0119 7 1/2 J _ 16 H 2 ET 40 Inner side of wheel: RUOTE OZ (foundry symbol) nd dte of mnufcture Vlves: Metl screw-on vlves in ccordnce with DIN 7779 with long nut Fixing: Tightening torque: Blnce weights: Only with M12 x 1.5 x 40 mm sphericl collr bolts supplied by the wheel mnufcturer 110 Nm Only dhesive weights re permitted G. Informtion for ordering replcement prts Replcement prts Designtion Prt no. Copyright DimlerChrysler AG 08.12.2004 CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 8
Light lloy disk wheel 7 1/2 J _ 16 H 2 ET 40 B6 602 00 57 Wheel trim B6 602 00 96 Sphericl collr bolt L=40 mm H WA201 401 02 70 Vlve H WA201 400 01 13 Tyre pressure sticker H WA201 584 00 39 Fender extension kit B6 602 00 72 A set of wheel locking bolts (Prt no. B6 602 02 01) cn be supplied upon request. Conversion to AMG 7 1/2 J _ 16 H 2 ET 40 disk wheel Refer to pge 2 for tyre dimensions. Pssenger cr Model 124 sedn/coupé/t-model The ppendix is divided up into the following sections: A. Assignment of tyre mke/model B. Specified minimum tyre infltion pressures A. Permitted mkes of tyre Vehicle model 124 Mke Description Sedn Coupé T-model Bridgestone RE 71 X X X Michelin MXX X X X Dunlop SP Sport D 40 X X X Pirelli P 700 Z X X X Pirelli P 700/P 7 X X not permitted Goodyer Egle VR/NCT X X not permitted B. Specified minimum tyre infltion pressures (br) Copyright DimlerChrysler AG 08.12.2004 CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 9
Refer to pge 2 for tyre dimensions. Vehicle model: 124 sedn/coupé/t-model Permitted mximum speed Vmx (km/h)1) Front xle Rer xle Level control system Perm. rer xle lod (kg)1) Permitted front xle lod (kg)1) Steel suspension Perm. rer xle lod (kg)1) 205/55 225/50 205/55 up to 1015 up to 1055 up to 1025 up to 1230 up to 1025 210 2.8 2.7 3.1 3.0 2.9 2.8 220 2.9 2.8 3.2 3.1 3.0 2.9 230 3.0 2.9 3.3 3.2 3.1 3.0 240 3.1 3.0 3.4 3.3 3.2 3.1 250 3.2 3.1 3.5 3.5 3.3 3.2 225/50 up to 1230 Mx. wheel cmber ngle (degrees) - 1 30' - 4-2 30' 1) Vlues for mximum speed nd permitted front xle or rer xle lods cn be obtined from the vehicle documents. Comments: Tyre infltion detils only pply for vehicles with mximum speed of up to 250 km/h. The tyre infltion pressure cn be reduced by p = 0.1 (br) per 100 kg reduction in xle lod. Remember tht tyre infltion pressure detils only pply for cold tyres! On wrm tyres vlues of up to 0.5 br higher re permissible. Do not reduce pressure of wrm tyres! Tyre infltion pressure my only be corrected when tyres re cold! Tyre infltion pressure detils relte to the use of permitted mximum speed nd permitted xle lod. Copyright DimlerChrysler AG 08.12.2004 CD-Ausgbe G/05/02 Will not be recorded by Modifiction services Pge 10