1KV DIGITAL MULTIFUNCTION INSULATION RESISTANCE AND CONTINUITY-VOLTAGE TESTER WITH MOV & GAS ARRESTER TESTING. Model 1154TMF

Similar documents
SOIL RESISTIVITY TESTER

4-20mA DC PROCESS CLAMP METER

OPERATION MANUAL MILLIAMP PROCESS CLAMPMETER MODEL - KM 071 LIST OF PRODUCTS

ANALOG INSULATION RESISTANCE TESTER

DIGITAL EARTH RESISTANCE Model KM 2030

THERMOCOUPLE CALIBRATOR Mode KM-CAL-710

HIGH VOLTAGE PROXIMITY DETECTOR

DIGITAL INSULATION RESISTANCE TESTER (5KV, 1T )

RTD CALIBRATOR Mode KM-CAL-720

TEMPERATURE CALIBRATOR Model KM-CAL-801

DIGITAL 4 WIRE EARTH RESISTANCE TESTER

LH41A. User Manual. Clamp On Ammeter. For detailed specifications and ordering info go to

INSTRUCTION MANUAL DT173 DT175 DIGITAL THERMOMETERS ALWAYS READ THESE INSTRUCTIONS BEFORE PROCEEDING

LM-100 LM-120. Light Meters. Users Manual. For detailed specifications and ordering info go to

INSTRUCTION MANUAL CM95/ CM100 TRUE RMS FLEXIBLE CLAMP METER. 1. SAFETY INFORMATION: Always read before proceeding. REMEMBER: SAFETY IS NO ACCIDENT

Tachometer. English. Users Manual

Instruction Manual PC104/PC105 3-PHASE SOCKET TESTER. Check out what else you can get from Martindale:

KMP Insulation-Continuity Tester. Users Manual

INSTRUCTION MANUAL CM69 TRMS AC EARTH LEAKAGE CLAMP METER. 1. SAFETY INFORMATION: Always read before proceeding. REMEMBER: SAFETY IS NO ACCIDENT

TX900. Microwave Leakage Detector. 99 Washington Street Melrose, MA Phone Toll Free

Temperature Probe, Battery (installed), Instruction Sheet, Quick Reference Card and Warranty Card.

Instruction Manual VT4 VOLTAGE TESTER. Check out what else you can get from Martindale:

MARTINDALE MARTINDALE IN2001/IN2003 INSULATION & CONTINUITY TESTERS INSTRUCTION MANUAL IN2001/IN2003 INSULATION & CONTINUITY TESTERS

Infrared Thermocouple Probe

TACH-10 Contact / Non-Contact Tachometer

THWD-3 and TH-3 Relative Humidity and Temperature Meters

CM100. Carbon Monoxide Meter. 99 Washington Street Melrose, MA Phone Toll Free

THWD-5. Relative Humidity Temperature Meter. Users Manual. For detailed specifications and ordering info go to

TIME-10 Process Control Stopwatch

Temperature Calibrator

MANUAL PCE-IT111

DT33B/C/D OPERATOR S MANUAL LIMITED WARRANTY AND LIMITATION OF LIABILITY

PRM-4. Phase Sequence and Motor Rotation Tester. Users Manual. For detailed specifications and ordering info go to

Users Manual. MegOhmMeter

i400s Calibration Information Introduction

PY-11 Voltage & Continuity Tester

362 Clamp Meter. Users Manual

TMD90A Dual Input Digital Thermometer

51 & 52 Series II. Users Manual. Thermometer. Test Equipment Depot Washington Street Melrose, MA TestEquipmentDepot.

Calibrator Capabilities Function Range Resolution Measure V dc 28 V 1 mv Measure ma dc Source ma dc

TIC 300 PRO. Users Manual Mode d emploi Bedienungshandbuch Manual d uso Manual de uso. Non Contact AC Voltage Detector. High Energy Tic Tracer

RS-3 PRO RS-1007 PRO. CAT IV Analog Clamp meter Series. Users Manual. For detailed specifications and ordering info go to

Flo-Way. Measure Granular or Powdered Material. Stand Alone or Connect to Other Devices for Blending. Used by Successful Producers World-Wide

User's Guide. Model RPM10 Laser Photo / Contact Tachometer with IR Thermometer. Introduction

Instruction Manual. 99 Washington Street Melrose, MA Fax TestEquipmentDepot.com. Model 308A Digital Insulation & Continuity Meter

P5510. Users Manual. Pneumatic Comparison Test Pump

Chek-A-Cell TM. Instruction Manual Rev A 8/12

362 Clamp Meter. Users Manual

Calibration Manual. Detachable Jaw True-rms Clamp Meter

IN1001/IN1003 ANALOGUE INSULATION & CONTINUITY TESTERS INSTRUCTION MANUAL IN1001/IN1003 ANALOGUE INSULATION & CONTINUITY TESTERS INSTRUCTION MANUAL

The following table shows the symbols used on the product and/or in this manual. Hazardous Voltage. Risk of electric shock.

80PK-2A Type K Immersion Probe

User's Manual. Earth Ground Resistance Tester. Model Introduction

User's Manual. Model Hot Wire Thermo-Anemometer. Introduction

1662/1663/1664 FC. Electrical Installation Tester. Safety Information. Warnings

IAQ-CALC INDOOR AIR QUALITY METER MODEL 7515

Instruction Manual VT25 / VT28 VOLTAGE TESTER ALWAYS READ THESE INSTRUCTIONS BEFORE PROCEEDING

FR1118- P10. User s Manual

Virtual Measurements & Control. VC210 Operators Manual

1587 FC/1587/1577. Insulation Multimeter. Safety Information. Warnings

TMA5 Mini Vane Anemometer

Panel Mount Digital Tachometer Model

This manual covers the following model:

TMULD-300 ULD-300. Ultrasonic Leak Detector. Users Manual. 99 Washington Street Melrose, MA Phone Toll Free

ODY-05-2 VOLTMETER FOR REMOTE MONITORING

Users Manual. Phase Rotation Indicator

Model Battery Powered Milliohm Meter

SOLAR DASH CHARGING SYSTEM USER GUIDE

TTH-1315 TTH-1315-A Temperature & Humidity Sensor User s Manual

IAQ-CALC TM Indoor Air Quality Meter

NEW 15KV HIGH VOLTAGE INSULATION RESISTANCE TESTER MODEL KM 7015 IN FEATURES : CAT IV 600V. Short Circuit Current 5mA.

Visit us at

Auto-Off & Power Hold Function

P5514, P5514-V & P5514-EP Hydraulic Comparison Test Pump

Digital Low Resistance Ohm Meter

Go to to register your product and find more information.

373 Clamp Meter. Users Manual

IAQ-CALC TM Indoor Air Quality Meter

KMP7010. Ground Resistance Tester. Users Manual

User's Guide. Vane Anemometer. Model Measures Air Velocity & Temperature. Degrees C/F switchable


A Member of the. Integrated Metering Technologies

Spy pocket Jeepmeter ope rati ng instructions

INSTRUCTION MANUAL. Rotary Unidirectional Piezoelectric Motor Evaluation Kit. (Model: UPM-28) Made in USA

Indoor Air Quality Meter

PVI 1800/PVI Residential/Commercial Grid-Tied Photovoltaic Inverter WARRANTY MANUAL. Subject to Change REV , Solectria Renewables

Cable Length Meter INSTRUCTION MANUAL

Models DP10 & DP20 Series Low Voltage Disconnects User s Manual Rev. 1.1 October 31, 2007

50407 / DUAL INDEPENDENT FOOTWEAR AND WRIST STRAP TESTER

365 Detachable Jaw True-rms Clamp Meter

302+/303 Clamp Meter. Users Manual

D4BS CSM_D4BS_DS_E_8_4

Freedom Designs, Inc. Embroidery Catalog. Over 50 New Design Options! Freedom 12Pg Embroidery Self Cov 1

MANLEY LABORATORIES, INC. MANLEY REFERENCE JUNIOR DAC OWNER'S MANUAL 20 BIT DIGITAL TO ANALOG CONVERTER

323/324/325 Clamp Meter

41210S CIRCUIT BREAKER FINDER WITH GFCI Instrucciones de uso Detector de Interruptores con GFCI 41210S. Operating Instructions

LED Emergency Drivers

MAX. AC 600V HOLD V M H.V. LIVE CIRCUIT DIGITAL INSULATION TESTER DO NOT OPERATE IF LIT POWER DATA HOLD TEST ON / OFF 250V 500V 1000V OFF CAT.

AMB V Insulation Resistance Tester. Users Manual. For detailed specifications and ordering info go to

GRUNDFOS INSTRUCTIONS. Grundfos ALPHA Installation and operating instructions

Transcription:

An ISO 9001:2008 Company 1KV DIGITAL MULTIFUNCTION INSULATION RESISTANCE AND CONTINUITY-VOLTAGE TESTER WITH MOV & GAS ARRESTER TESTING FEATURES : Auto Discharge Function on all tests & all ranges. Gas Arrester Test MOV / Protection Devices Test Preselectable Measurement Time : Auto Stop on completion of Test Auto Stop & Hold Function. TM Ener Save Can be calibrated in All calibration laboratories Buzzer ON/OFF by key : Always ON Nominal Voltage @ 1mA on all Insulation Ranges Continuity Short Circuit Current >220mA (225mA typical) Continuity Open Circuit Voltage of 5V DC Smart Hold & Stop on Voltmeter AC / DC Test ON/OFF Fuse : fast HBC 600V / 500mA Low Voltage 50V Range for Telecom application Model 1154TMF GENERAL SPECIFICATIONS : ï Insulation Resistance Range : 0.1MW ~ 10GW ï Selectable Test Voltages(Low Voltage for Telecom) : 50 / 100 / 125 / 250 / 500 / 1000V ï LCD Type : Large Type 2 x 16 Characters ï Continuity Measurement : 0.01 to 1999 ï Automatic AC / DC Voltage Test At Start-Up ï AC Voltage Measurement : 0 to 700V ï DC Voltage Measurement : 0 to 950V ï Battery Load Current : About 300mA ï Battery Test at switch ON / RESET Lead Resistance Null Facility ï Auto Off approx. 5 minutes 0 0 ï Operating Temperature : 1 C to 55 C not in full sun 0 0 ï Storage Temperature : -20 C to 70 C ; Relative Humidity max. 80% R.H. ï Open Current : about 19.15mA ï Consumption Current : about 193.5mA. ï Power Supply : 8 x1.5v Alkaline batteries. ï Dimension : 175(L) x 85(W) x 75(H) mm ï Weight : Approx. 655gms. ACCESSORIES : Test leads, Shoulder belt, carrying case, Instruction manual & Batteries. Metal Oxide Varistor SAFETY : CE marking according to the Low Voltage Directive (73/23/eec & 93/68/eec) and EMC Directive (89/336/EEC, 92/31/EEC, & 93/68/EEC) and found to comply with the essential requirement of the directives. IEC/EN 61010-1:2001. EN61326+A1+A2+A3, EN55011+A1+A2, EN61000-3-2+A2, EN61000-3-3+A1+A2, EN61000-4-2+A1+A2, EN61000-4-3+A1, EN61000-4-4, EN61000-4-5+A1, EN61000-4-6+A1, EN61000-4-11 Gas Arrester ELECTRICAL SPECIFICATIONS : 1154T MF CONTINUITY SHORT CIRCUIT CURRENT > 220mA : Range Accuracy 0.01 ~ 100 W ±1% rdg 100 ~ 300 W ±1.5% rdg 300 ~ 1999 W ± 2% rdg Auto - Null -upto 5W Buzzer - Threshold Value Up to 3 INSULATION TEST Test Voltage Insulation Resistance Accuracy 50 V 2 k ~ 400 MW 100 V 2 k ~ 800 MW 125 V 2 k ~ 1 GW < 30kW : ± 20%rdg 30kW ~ 1MW : ± 5%rdg 250 V 2 k ~ 2 GW > 1MW : ± 3% rdg 500 V 4 k ~ 4 GW 1000 V 8 k ~ 10GW Metal Oxide Varistor (MOVs) Test Voltage Resolution Accuracy 5 ~1020V ± 2 Counts ±3%rdg Arrester Voltage result @ 1mA Test Voltage Resolution Accuracy 5 ~1020V ± 2 Counts ± 2 Counts ±3%rdg ±3%rdg VOLTMETER (AUTORANGING) Test Voltage Resolution Accuracy 0 ~ 950V DC ± 1V ± 1.5% F.S 0 ~ 700V DC ± 1V ± 1.5% F.S Auto - Hold An ISO 9001:2008 Company All Specifications are subject to change without prior notice G-17, Bharat Industrial Estate, T. J. Road, Sewree (W), Mumbai - 400 015. INDIA. Sales Direct.: 022-24156638, Tel. : 022-24124540, 24181649, Fax : 022-24149659 Email : kusam_meco@vsnl.net, Website : www.kusamelectrical.com

AN ISO 9001:2008 COMPANY DIGITAL MULTIFUNCTION & INSULATION CONTINUITY - VOLTAGE TESTER MODEL - KM 1154TMF 17, Bharat Industrial Estate, T. J. Road, Sewree (W), Mumbai-400015. INDIA Sales Direct: (022)24156638 Tel.:(022) 2412 4540, 2418 1649 Fax: 2414 9659 E-mail : kusam_meco@vsnl.net, Website : www.kusamelectrical.com; www.kusam-meco.co.in OPERATION MANUAL

TABLE OF CONTENTS TITLE PAGE Safety Rules... 1 Safety Checks... 2 Don't Touch... 2 General Description... 3 Brief Product Description... 4 Notes... 5 Features... 6 Pre-testing Safety... 8 Operating Instructions... 9 Inside Lid Instructions... 12 Very Important Automatic Features... 13 Features Comparisons... 14 Principle of how they work and Results... 15 Preparation for use... 17 Replacing the batteries... 17 Fuse Replacement... 17 Specifications... 18 Test Certificate... 20 Warranty... 21-1-

-2- -3-

NOTES -4- -5-

-6- -7-

-8- -9-

-10- -11-

-12- -13-

-14- -15-

-16- -17-

-18- -19-

MUMBAI TEST CERTIFICATE DIGITAL MULTIFUNCTION & INSULATION CONTINUITY - VOLTAGE TESTER This Test Certificate warrantees that the product has been inspected and tested in accordance with the published specifications. The instrument has been calibrated by using equipment which has already been calibrated to standards traceable to national standards. MODEL NO. KM 1154TMF SERIAL NO. DATE: ISO 9001 REGISTERED QC KUSAM-MECO PASS WARRANTY Each KUSAM-MECO product is warranted to be free from defects in material and workmanship under normal use & service. The warranty period is one year (12 months) and begins from the date of despatch of goods. In case any defect occurs in functioning of the instrument, under proper use, within the warranty period, the same will be rectified by us free of charges, provided the to and fro freight charges are borne by you. This warranty extends only to the original buyer or end-user customer of a KUSAM-MECO authorized dealer. This warranty does not apply for damaged Ic s, fuses, burnt PCB's, disposable batteries, carrying case, test leads, or to any product which in KUSAM-MECO s opinion, has been misused, altered, neglected, contaminated or damaged by accident or abnormal conditions of operation or handling. KUSAM-MECO authorized dealer shall extend this warranty on new and unused products to end-user customers only but have no authority to extend a greater or different warranty on behalf of KUSAM-MECO. KUSAM-MECO s warranty obligation is limited, at option, free of charge repair, or replacement of a defective product which is returned to a KUSAM-MECO authorized service center within the warranty period. THIS WARRANTY IS BUYER S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. KUSAM-MECO SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE WHATSOEVER. All transaction are subject to Mumbai Jurisdiction. -20- -21-