brano industries (pty) ltd. P O Box 277, Bramley, 2018, Rep. of South Africa. tel (011) 887-0625 fax (011) 887-7616 Share-call :- 08600 - BRANO 08600-27266 e-mail :- sales@brano.co.za Website :- www.brano.co.za "pro-rola 1" Adaptor Kit for Steel Roll-Up Doors INSTALLER'S MANUAL Installation Instructions for Automation of Steel Roll-Up Doors "CABLE AND PULLEY" SYSTEM Manual Coce :- MAN - 04 Version 3 ( 2003 ) When in doubt...... Read the manual!!!! COPYRIGHT Patent Number 96 / 10092 ; Priority No. ZA 95 / 10422 C "pro-rola 1" version 3 ( 1995 / 1999 / Sept 2003 ) file:- Coreldraw10\Manuals\Prorola1Vers3.cdr
"pro-rola 1" Installation Instructions "Cross-over Pulley" on R.H.S. Motor Bracket Steel Wire Rope Wall Fixing Screw Steel Roll-up Door Door Towing Brackets Bottom Pulley Wheel LHS Mounting Bracket. ( Extrusion anchor side ) RHS Mounting Bracket. ( Motor support side ) Oblique angle view from inside the garage showing the relative positions of the mounting brackets Notes:- 1) For reasons of clarity, the door operator is not shown in position, and... 2) the routing of the wire rope has been overlaid and emphasised in order to show it's position relative to the door. 3) The door towing arms are attached to the forward ropes at both sides of the door. 4) The bottom pulley wheels are fixed to the floor and wall at both sides of the door. page 1
Minimum Headroom Clearance 70 mm Minimum Space Requirements Minimum Side Clearance 80 mm Both Sides of Door * Door Curtain Roll Ceiling Door Shaft Door Support Bracket Door Guide Channel Floor Level Width of door curtain Length of door shaft Overall width of garage Opening height of door Lintel Floor to centre Door Shaft NOTES:- 1) The standard "pro-rola 1" Adaptor Kit is designed to suit a door up to 2500 mm wide x 2135 mm high. 2) For non-standard size doors, special "pro-rola 1", "pro-rola 2" and "pro-rola 3" Adaptor Kits are available on request. 3) The maximum clear open height possible for the door is dependent on the overall width of the garage available for mounting the "pro-rola 1" door operator / adaptor system and the length of the door shaft. 4) ORDERING INFORMATION:- For non-standard size doors, always state the following:- Overall width of garage = mm. Overall length of door shaft = mm. Overall width of door curtain = mm. Opening height required. = mm Floor to centre of the Door Shaft. = mm page 2
Wall Extrusion Anchor Bracket always on left hand side. PLAN VIEW ( Looking from the top ) Motor Head always on right hand side. Motor Head pro-alpha 2000 LHS Mounting Bracket RHS Mounting Bracket SIDE VIEW of MOTOR MOUNTING "Towing" Bracket Driving Traveller Following Traveller Wire Rope "Eye" Bolt Tensioning Nut ENLARGED DETAIL Rope Clamp DO NOT OVER-TENSION THE WIRE ROPE page 3 Emergency Release Cord
Motor Support Bracket ( RHS Bracket ) INSTALLATION PROCEDURES 1 Place the two support brackets in place approx. 20 mm from the edge of the door curtain. Pulley No 5 ( Cross-over Pulley ) Wall Fixing Pulley No 8 2 Fix the brackets to the wall and clamp them to the door shaft using the "U" bolts supplied. 3 Place the motor in the RHS Motorhead Support Bracket and secure the extrusion to the LHS Anchor Bracket. 4 Slide the "Slave Traveller" into the extrusion. NOTE:- The "Slave Traveller" does not have a worm-nut as it is used only as a stabilising support Door "U" Bolt Pulley No 7 Front Rope Bottom Pulley Bracket Pulley No 6 Lintel Back Rope VIEW FROM RIGHT HAND SIDE Pulley No 4 Pulley No 1 Extrusion Support Bracket ( LHS Bracket ) Back Rope Bottom Pulley Bracket Pulley No 2 Front Rope Pulley No 3 for the "T", ( i.e. "Towing" ), Bracket. 5 Insert the "Eye" Bolt through the "T" Bracket as shown. 6 Establish the positions for the two Bottom Pulley Brackets, ( Pulleys Nos. 3 & 6 ). Drill the holes for the fixing screws. 7 Anchor the two Bottom Pulley Brackets in place. 8 Reeve the wire rope around the pulleys in the order shown, i.e. Nos. 1, 2, 3, 4, 5, 6, 7 & 8 and back to the "T" Bracket. VIEW FROM LEFT HAND SIDE page 4
Back Rope ( Closest to Wall ) Front Rope Door Towing Bracket ( RHS shown ) Bottom Rail of Door Fix the Door Towing Brackets to the Bottom Rail of the door. Use the wood packing blocks if necessary. Bottom Pulley Wheel fixed to floor 9 Pull the wire rope gently by hand until the slack is taken up. Secure the rope in place using the "Rope Clamp" supplied. 10 Make the final tension adjustments using the "Tensioning Nut" on the "Eye Bolt". Tighten the nut until the rope has a tension of approx. 10 kgs. BE CAREFUL NOT TO OVER- TENSION THE WIRE ROPE. 11 Attach the two "Door Towing Arm Brackets" to the bottom rail of the door. If the door does not have a sturdy bottom rail, use the plastic ( or timber ) packing blocks supplied to space the Towing Arms away from the door channels. 12 Disengage the "Driving Traveller" from t h e w o r m - s h a f t b y p u l l i n g t h e "Emergency Release Cord" which is attached to the "Traveller Lever" 13 Move the two travellers and "T" bracket assembly to the "door closed" position, i.e. to the LHS. Now... Set the "down" travel limit switch in place. 14 Close the door. 15 Clamp the "Door Towing Arms" to the "forward" ropes as shown. 16 Raise the door to the "full open" position. Set the "up" travel limit switch in place. 17 Test the operation of the door. Be sure to check the "safety reverse" feature of the operator. If the door is obstructed during it's working cycle, the door operator must respond as follows :- whilst closing... ( Place a 40 mm thick plank or piece of square tubing under the centre of the door. ) The door must stop and reverse direction within 2 sec after making contact with the obstruction. whilst opening... the door must stop! It should remain stationary until a new command is transmitted to the operator. page 5
REEVING LAY-OUT of WIRE ROPE Pulley No. 5 ( Cross-over Pulley ) Pulley No. 7 Pulley No. 8 Pulley No. 4 Pulley No. 2 Pulley No. 1 Start Here "T" Bracket Wire Rope Coupler Wire Rope ( one piece ) Pulley No. 6 Pulley No. 3 Brano Industries ( Pty ) Ltd. P.O. Box 277 Bramley, R.S.A., 2018 (27)(011) 887-0625 (27)(011) 887-7616 page 6 Patent Number 96 / 10092 Priority No. ZA 95 / 10422 Copyright March 1996 C
- brano industries (pty) ltd. Copyright C 1995 / 1998 / 2003 Head Office :- Johannesburg Branches :- Cape Town, Pretoria, Durban, Westrand, Bloemfontein "pro-rola 1" ADAPTOR KIT for Standard Single Size Steel Roll-Up Door 2440 Wide x 2135 mm High L A 1" Kit "PRO -RO for Do or Sing le br ano i ndu stri e s (pty ) ltd Singl e Door " P RO- RO LA 1" Kit Stock Code:- 1 KROLA 1-01 "Pro-Rola 1" Adaptor Kit complete. ( Door Operator not included ) Motor Support Bracket Assembly (including Pulleys) Extrusion Anchor Bracket Assembly (including Pulleys) Door Towing Arms Left Hand Side 2 KROLA - 03 Hanger Bracket 2 KROLA 1-01 2 KROLA 1-02 Slave Traveller ( without Nut ) Right Hand Side 2 KROLA - 04 Wire Rope 2 mm ( Specify size of door )) 2 BRAH-3 2 TRAV - 02 2 KROLA 1-03 Fasteners Kit Bottom Pulley Bracket Assembly Traveller Towing Bracket Packing Blocks Hie ng F a s te ne r s 4 F K 0 2 0 1 Timber or Plastic 4 FKPR 1 2 KROLA - 02 2 KROLA 1-05 TIMB 1-02 "Pro-Rola 1" Installation Instruction Manual This "pro-rola 1" system was installed by:- Company... Date... Installer... Tel... MANUAL - 04 Comments... page 7