Encore S8/L8/S/L/S8/L8 Section II Parts and Service Manual (9049B) CLARKE TECHNOLOGY Operator's Manual - Encore S8/L8/S/L/S8/L8 - -
HOW TO CORRECT PROBLEMS IN THE MACHINE PROBLEM CAUSE ACTION The machine does not remove all the water from the floor. The squeegee is up The vacuum tank is full. The screen filter is dirty. There is an obstruction or damage in the squeegee, squeegee hose or standpipe. The vacuum motor is not running. The squeegee hose is disconnected. The squeegee blade is damaged, worn, or incorrectly installed. The squeegee pressure is not correctly adjusted. The gaskets on the cover of the recovery tank are damaged. Lower the squeegee. Drain the tank. Clean the screen filter. Remove the obstruction or repair the damage. Check for tripped breaker. Have an authorized service person make repairs. Connect the hose. Turn or replace the squeegee blade. Correctly install the squeegee blade. Adjust the pressure of the squeegee. Replace the gaskets. The batteries do not give the normal running time. The battery terminals are dirty or damaged. The electrolyte level is too low. The batteries are not fully charged. The charger is damaged. The battery is defective. The batteries are disconnected. Clean the terminals and connectors. Replace the damaged cables. Charge the batteries. Add distilled water to each cell and charge the batteries. Charge the batteries for a full hour charge. Have an authorized service person repair the charger. Check voltage of each cell while discharging. Connect the batteries. The cleaning is not even. The scrub brushes or pads are worn. There is damage to the brush assembly, casters or the solution valve. The brush motors are not running The solution level is low. Replace the scrub brushes or pads. Have an authorized service person make the needed repairs. Check for tripped breaker, reset. Check for loose connections. Fill the solution tank. NOTE: If the motors continue to stop consult an authorized service person. The machine does not run. The machine loses power. Reset the circuit breaker. Check wire connection to traverse motor. Replace the fuses. Check the batteries connections. Check parking brake overide lever position (if installed) NOTE: If the motors continue to stop, consult an authorized service person. Page -8- CLARKE TECHNOLOGY Operator's Manual -Encore S8/L8/S/L/S8/L8
MAINTENANCE Adjusting Brush Head Position Switch: (See figure 4).Turn "ON" the key switch.. Start with the brush head up/down switch in the "Up" position and the brush pressure knob set to minimum, fully counter clockwise. This should cause the brush head to be in the full "Up" position.. Install the proper brushes or pads and pad drivers for the machine. 4. Leave the brush pressure knob set to minimum, fully counter clockwise. Switch the brush head up/down switch to the "Down" position. This should cause the brush head to travel down to the floor until the brush position switch (44A) is closed. At this time the brush head actuator will stop running down.. Check at the front of the machine to see if the brushes or pads are completely flat on the floor. The screw, that goes through the brush head actuator tube (988A), should be at the top of the. inch slot in the tube. If the brushes or pads are not on the floor, or the screw is not at the top of the slot, the brush position switch (44A) needs to be loosened and moved up or down in the slot on the switch mount bracket (9A). Retighten the brush position switch.. Figure #4.Keep the brush pressure knob set to minimum, fully counter clockwise. The brush head will need to be raised and lowered again with the brush up/down switch. Check to see if the adjustment put the brushes or pads on the floor and kept the screw at the top of the tube. If no, repeat step # until this step is completely accomplished. Replacing a Defective Brush Head Hall Affect Sensor (L Series only)(see figure ).Remove the brush head actuator assembly from the machine.. Loosen the locking nut on the brush head hall affect sensor at the top of the brush head actuator.. Unscrew the brush head hall affect sensor (Part Number 44A) from the top of the brush head actuator. Figure # 4. Screw in the new brush head hall affect sensor into the top of the brush head actuator until it touches the metal disk on the motor gear. Unscrew the brush head hall affect sensor from the top of the brush head actuator three () complete turns.. Using the supplied jam nut, lock the brush head hall affect sensor down using loctite thread locker..reinstall the brush head actuator assembly on the machine. CLARKE TECHNOLOGY Operator's Manual -- Encore S8/L8/S/L/S8/L8 -- 9 --
Squeegee/Swing Arm Assembly Drawing /99 Drawing # A - L Drawing # A - S 0 8 9 4 0 4 4 4 40 8 4 0 8 0 48 4 9 4 8 4 9 0 8 NOTE: # and # are on top of the bracket for the "S" models 44 9* 4 4 4 49 * Apply antiseize to threads Page -0- CLARKE TECHNOLOGY Operator's Manual -Encore S8/L8/S/L/S8/L8
Squeegee/Swing Arm Assembly Parts List /99 Ref # Part No. Description Qty Model A Pulley All 8A Washer, Nylon ¼x¼x /8 All 04A Swing Arm, Front All 4 8004A Screw,.-0 x.0 All 8A Screw,.- x.00 All 804A Nut, Hex ESNA SS All 80A Strap All 8 9A Cable, Lower All 9 A Bumper All 0 900 Nut, ESNA All 044A Swing Arm, Rear All 90 Nut, Hex All 80A Nut, ESNA SS All 4 909 Nut, 0-4 ESNA SS All 998 Screw, 0-4 x.0 All 84A Washer, Nylon ½x¼x /8 All 800A Screw, Shoulder All 8 4A Spring, Squ. Pressure All 9 80A Stud All 0 09 Screw, SS Hex All 490A T Handle All 980 Washer, Flat. All 08A Pivot Bracket All 4 0A Knob All 9A Hose, Squeegee Rec. All A Tube Bracket All 40B Squeegee Gasket All 8 80A Nut, Jam SS 4 All 9 99A Wheel All 0 9A Wheel Mount Bracket All 9048 Nut, Jam All 9804 Washer, Flat 4 All 990A Guide Wheel All 4 9808 Washer, Lock All NOTE: When changing squeegee blades, it might be necessary to loosen screw #9; install and secure blades with clamp #44; then retighten screw #9. This will allow for different thickness. Ref # Part No. Description Qty Model 9A Squeegee Base 8 94A Squeegee Base 9A Squeegee Base 8 9A Squeegee Base, 9" acc. 8 80A Screw, PN Phillips All 80A Spacer 8 8A Spacer 8A Spacer 8 8A Spacer, 9" accessory 8 8 A Air Duct All 9 800A Screw,.- x.00 All 40 0A Grip Pad All 4* 094A Blade, Inner 8 09A Blade, Inner 094A Blade, Inner 8 090A Blade, Inner Ribbed 9" 8 4* 09A Blade, Outer 8 09A Blade, Outer 09A Blade, Outer 8 09A Bade, Outer 9" acc. 8 4 4A End Clamp All 44 44A Clamp, Weld 8 44A Clamp, Weld 444A Clamp, Weld 8 44A Clamp, Weld 9" acc. 8 4 8004A Screw,.-0 x.0 Hex All 4 09 Rivet All 4 80A Screw,.-0 x. All 48 88A Screw,.-8 x. All 49 A Squeegee Strap Latch All 0 8A Nut, ½-0 All 9008 Nut, Hex ¼-0 All 980 Washer, ¼ Lock All 8A Washer,Nylon ¼x¼x / 4 All 4 88K Asm., Squeegee 8 88K Asm., Squeegee 88K Asm., Squeegee 8 888A Asm., Squeegee* 8 80A Nut, ¼-8 All 4A Insert,Threaded /-4 All 80A Washer 4 All * See accessory page CLARKE TECHNOLOGY Operator's Manual - Encore S8/L8/S/L/S8/L8 - -
Traverse System Assembly Drawing /00 Drawing 90A 4 8 0 8 9 9 4 8 4 0 9 9 0 0 Page -- CLARKE TECHNOLOGY Operator's Manual -Encore S8/L8/S/L/S8/L8
Traverse System Assembly Parts List /00 Drawing 90A Ref # Part No. Description Qty Model A Swing Arm Pin All 8 Hair Pin All 804A Nut,.-0 ESNA All 4 98A Swing Bracket All 88A Screw,.-8 x. All A Cable Pulley All 8A Washer, Nylon ¼x¼IDx.0 All 8 8004A Screw,.-0 x.0 All 9 80A Screw,.- x.0 All 0 800A Screw,.-0 x All 900 Nut,.- ESNA All 8999 Caster Assembly All 80A Nut,.- ESNA All 4 9A Transaxle, Imperial All (see page 4, 4 for parts) 80A Screw, Hex 4 All 999A Wheel Assembly* All 99A Wheel, Foam Filled (opt.) All 4B Wheel Cover All 8 8A Lug Nut, 0-0 UNF All 9 9804 Washer, Star Lock. All 0 00A Main Frame All 9A Transaxle Mount All 9A Spacer All 8A Washer, Nylon ¼x¼IDx/ All 4 800A Screw, /8- x All 80A Nut, /8- All 088 Washer, Lock /8 All 849A Stud, /8M x /8F All 8 9800 Washer,. Fender All 9 99A Strap, Static All 0 9804 Washer, Flat /8 All 944 Screw, /8- x ¾ 4 All 9808 Lockwasher /8 4 All *009A tube, inner (included in item #) Ref. CLARKE TECHNOLOGY Operator's Manual - Encore S8/L8/S/L/S8/L8 - -
Brush Head Assembly Drawing /00 Drawing # (i) 4A, 449A, 4A Drawing # (ix) 448A, 44A, 40A 4 4 8 8 8 0 0 9 0 9 9 8 4 4 0 4 8 9 8 49 4 0 9 8 4 4 8 0 4 4 8 9 8 40 4 49 48 4 4 4 44 4 Page -4- CLARKE TECHNOLOGY Operator's Manual -Encore S8/L8/S/L/S8/L8
Brush Head Assembly Parts List /00 Ref # Part No. Description Qty Model 80A Pin All 4A Main Frame Ref All 80 Hair Pin All 4 944 Screw,.-x. 9 All 988A Switch Bracket All 98008 Washer, # 4 All 900 Nut, #- ESNA 4 All 8 80A Nut,.- ESNA All 9 900 Nut,.-8 ESNA All 0 9A Switch Mount All 44A Lever, Switch All 9980 Screw, #-x.00 PN 4 All 808A Nylon Spacer All 4 440A Diode L series 008A Actuator & Tube Asm. S series 009A Actuator & Tube Asm. L series (includes item #) 988A Head Pressure Tube All 844A Screw,.-0x. All 8 800A Washer, Flat. All 9 0 44B Whisker Switch All 0A Linkage Bar 4 All 888A Screw,.0-0.0 8 All 0B Sleeve Bearing 8 All 4 908 Nut, Jam 0-0 All 980 Washer, Lock.0 8 All 980 Washer * 4 All 804A Nut,.-0 ESNA All 8 8A Sleeve All 9 8A Nylon Spacer All 0 4A Head Pressure Spring L series 4a Head Pressure Spring S series 9A Brush Head Mount All 40A Connector 4 All 40A Housing 4 All **** 40A Brush Motor. HP S8/L8/S 40A Brush Motor.00 HP L/S8/L8 4 90 Key All 09 Screw, Hex 4 All 80044A "U" Bolt All 480A Electric Valve All 8 00 Hose Clamp All 9 04A Hose All 40 804A Solution Splitter All 4 0B Left Brush Housing 8 44B Left Brush Housing 4B Left Brush Housing 8 4 84A Left Skirt 8 844A Left Skirt 84A Left Skirt 8 *Used only as required to square up linkage bars # to the frame. **Attach to Brush Motor. ***See page for installation ****Includes Item # Ref # Part No. Description Qty Model 4 800 Clamp All 44 04A Brush Hose All 4 809A Nut, 8- ESNA SS 4 All 4 880 Gimbal, Female All 4 880 Brush Holder Spring All 48 A Latch All 49 999 Screw, 8-x. SS 4 All 0 9808 Washer, Lock. 8 All 949 Screw,.-0x.00Pn Hd All 98A Rubber Washer All 4400B Gimbal, Male All 4 94 Screw,.-8x. Soc. All 4B Poly Brush Assembly-4 8 44B Poly Brush Assembly- 44B Poly Brush Assembly-9 8 4B Grit Brush Assembly-4 8 4B Grit Brush Assembly- 4B Grit Brush Assembly-9 8 C Pad Driver Assembly-4 8 0C Pad Driver Assembly- 4B Pad Driver Assembly-9 8 94A Center-Lok Asm. All (Pad Driver Only) 9 Screw, 0-x.88 All (Pad Driver Only) 8 8A Gimbal Collar All 9 A Brush Plate-8 8 A Brush Plate- 4A Brush Plate-8 8 0 88A Screw,.-8x. Hex 4 All 84A Right Skirt 8 84A Right Skirt 84A Right Skirt 8 98A Latch Tab All 80A Screw,.-x. SS Pn All 4 8A Screw, 0-x. Pn SS 8 8A Screw, 0-x. Pn SS 8 8004A "T" Nut 0-8 8004A "T" Nut 0-8 4A Keeper All 00A Right Brush Housing S8 00A Right Brush Housing L8 00A Right Brush Housing S 00A Right Brush Housing L 004A Right Brush Housing S8 00A Right Brush Housing L8 8 9048 Nut,.- Jam Thin ESNA All 9 990A Guide Wheel All 0 9804 Washer, Flat. All 9808 Lockwasher All 0 Hose Clamp All *** 44A Brush Head Sensor Lseries **NI A Label, Front Motor Sseries **NI A Label, Front Motor Lseries **NI 09A Label, Moving Parts All CLARKE TECHNOLOGY Operator's Manual - Encore S8/L8/S/L/S8/L8 - -
Solution/Recovery System Assembly Drawing /00 4 9 8 8 9 0 4 9 8 4 0 4 8 8 4 9 4 0 8 9 4 48 4 49 0 8 9 40 4 4 44 4 4 44 4 4 8 8 0 0 44 44 0 9 Page -- CLARKE TECHNOLOGY Operator's Manual -Encore S8/L8/S/L/S8/L8
Solution/Recovery System Assembly Parts List /00 Ref # Part No. Description Qty Model 4A Recovery Lid Gasket All 04A Recovery Lid All 98A Stand Tube All 4 4000A Float Switch (include # All & each # & #8) 49A Strain Relief All 8A Seal All 804 O-Ring All 8* 909 Nut All 9 448 Gasket All 0 8A Vac Motor Spacer All 80A Washer, Flat. All 88A Screw,.-0 x 4.00 Hex All 409A Vac Motor (also order All each # and #9) 4 B Label, Battery Installation All (NI*) 88A Screw,.-8x. Hex 4 All 980 Washer, Lock. 4 All 9800 Washer, Fender. 4 All 8 9A Vac Hose All 9 09A Label, Falling Parts All (NI*) 0 0A Squeegee Adapter All 4809A Contact 4 All 800A Locknut All A Rocovery Tank Drain Hose All 4 800 Hose Clamp All 90A Hinge Pin 4 All 88C Recovery Tank, incl # All 88 Battery - 0 AH - Volt All 8984 Battery - 0 AH - Volt All 4004A Battery - 0 AH - Volt All 8 800A Strap 4 All 9 998 Screw, 0-4x. Pan All 0 9804 Washer, Flat. All 80A Nut,.- ESNA All 909 Nut, 0-4 ESNA 4 All 00A Solution Lid All 4 409B Front Cover 8, 49B Front Cover 8 N *Recommended torque +_ inch/ pounds. *klskfjlksdjflkjflksajflkjfdlksfdj (NI*) = Not Illustrated Ref # Part No. Description Qty Model 989A Support Bracket All 089 Washer, Lock. All 09 Screw,.-0x. SS Hex All 8 8A Washer, Nylon /x /8x / All 9 8004A Screw,Shoulder.-0x All 40 948A Recovery Tank Support All 4 A Latch All 4 90 Screw, 8-x.0 Pn. 4 All 4 09A Solution Tank Adapter All 44 00 Hose Clamp All 4 8440 Series Cable - 9" All 40A Series Cable - " All 4 408A Battery Cable All 4 804A Washer,Fender.x¼ All 48 80A Screw,.-x.0 Hex All 49 88C Solution Tank All 0 4900A Stationary Handle All 044A Hose All 998 Screw, 0-4x. Pn. All 890 Drain Valve Handle All 4 840 Drain Gasket All 8940 Drain Valve All 800 Hose Clamp, Drain Valve All 994 Screw, 8-8x. Pn. All 8 0449A Drain Hose All 9 94A Battery Drain Valve All 0 044A Solution Hose All 08A Connector All 88 Filter Screen All 804 Hose Adapter All 4 880 Elbow All 04Au Hose All 809A Vac Filter All 984A Clamp, Metal All 8 440A Housing, Blue All 9 440A Housing - Black All 0 8940 Asm., Drain Valve 980 Washer, ¼ Lock All 99 Screw, ¼-0x/8 All 9A Washer, Rubber All 4 80A Washer All 84A Screw All 9 Screw All 9 Screw 0-x All 8 8A Cable Clamp All 9 8800A Well Nut All 80 09A Label, Gases & Chem. All(NI*) CLARKE TECHNOLOGY Operator's Manual - Encore S8/L8/S/L/S8/L8 - -
Control Housing Assembly Drawing /00 Drawing# A (IX) and A (I) 4 8 0 9 0 44 0 8 48 49 4 9 0 44 4 8 4 9 4 4 44 4 4 44 9 4 4 4 0 9 8 8 4 4 0 4 8 9 40 4 4 Page -8- CLARKE TECHNOLOGY Operator's Manual -Encore S8/L8/S/L/S8/L8
Control Housing Assembly Parts List /00 *#8 must use red loctite set screws. Ref # Part No. Description Qty Model 0A Knob S series 0A Knob L series 48B Switch, Head up & down Rocker All 48A Switch, Squeegee/Vac Pos./Rocker L series 4 8A Screw, 0-4 x. Pn. All 44B Control Panel Label L series 000A Control Panel L series 4B Control Panel Label S series 008A Control Panel S series 4408A Solution Flow Module All 8 4900B Speed Control Harness All 9 444B Battery Meter All 0 84B Spacer All 900 Nut, - ESNA All 00A Head Pressure Adjustor L series 89A Screw,.-0 x. Pn All 4 99 Screw,.-0 x. L series 99 Screw,.-0 x. S series 999 Screw 8- x. Pn 4 L series 4A Head Pressure Control Board L series 4A Upper Electrical Panel L series 8 480A Key Switch All 9 44A Actuator Control Board L series 0 84849 Insulator All 08 Screw, ¼-0 x /4 Set All 44A Circuit Breaker A All 9 Screw, 8- x. Set L series 9 Screw, 8- x. Set S series 4 4448A Circuit Breaker 0A Scr. All 44A Circuit Breaker A Scr. All 44A Circuit Breaker A All 440A Circuit Breaker.A L series 8 4B Control Housing L series B Control Housing S series 9 80A Nylon Washer, Key Switch All 0 9 Hour Meter All 409A Control Handle All 890A Screw,.-0 x. Pn All 49A Pin, Left Hand All 4 498A Actuator, Control Harness L series 089 Washer, Lock. All 00A Toggle Switch All 0A Centering Bracket All 8* 904 Screw, Set.-8 x. 4 All 9 08A Control Handle Spring All 40 A Control Bracket All 4 48A Pin, Right Hand All 4 49A Main Harness (L Series Only) L series 499A Main Harness (S Series only) S series 4 80A Stud All 44 800A Washer S series 800A Washer L series 4 980 Lock Washer L series 980 Lock Washer S series 4 4A Insert 8 L series 4 8A Screw, 8- x /8 4 L series 48 980 Washer, Nylon IDxODx.04 All 49 8004A Screw, Shoulder All 0 00A Gasket, Panel S series 00A Gasket, Panel L series 0B Label, Control Wiring L series B Label, Control Wiring S series 80A Washer All 804A Nut, ¼-0 ESNA All 4 A Collar All 8A Retainer Key/Hour Meter All 004A Stud, / x /4-0 Thread All 4008B Module Sequencer All 8 4008A Harness, Sequencer All 9 888A Screw, 0-4 x ½ L Series CLARKE TECHNOLOGY Operator's Manual - Encore S8/L8/S/L/S8/L8-9 -
Rear Cover Assembly Drawing /00 Drawing A & A 0 49 48 4 49 48 8 0 9 9 8 8 9 4 4 44 0 9 8 0 0 4 4 4 4 4 4 4 40 9 4 4 4 0 44 4 8 4 8 8 Page -40- CLARKE TECHNOLOGY Operator's Manual -Encore S8/L8/S/L/S8/L8
Rear Cover Assembly Parts List /0 *# must use red loctite. NOTE: indicates a change has been made since the last publication of this manual. Ref # Part No. Description Qty Model 4A Actuator, Mount Bracket L series 99 Screw,.-0x. Hex All 8004A Screw,.-0x.0 Hex L series 4 A Cable Pulley L series 804A Nut,.-0 ESNA L series 804A Nut,.-0 ESNA 9 S series 98A Pulley Bracket L series 800A Screw,.-0x.00 Hex S series 8 80A Washer, Flat. S series 9 080 Spacer S series 0 90 Nylon Bearing S series 400A Actuator L series 900 Nut, - ESNA L series 900 Nut, - ESNA 4 S series 4A Shaft S series 4 9A Squeegee Lever S series 480 Spring S series 900 Shoulder Screw S series A Squeegee Lift Bracket S series 8 84A Wear Plate S series 9 980 Washer S series 0 94 Screw, 0-4 x.0 Pn S series 44A Switch S series 9980 Screw, - x.00 Pn L series 9980 Screw, - x.00 Pn 4 S series * 904 Screw,.-8 x.0 Set S series 4 8A Lever Weld. S series 8A Upper Cable Assembly S series 408A Battery Cable Ref All 440A Cable Assembly All 8 480A Solenoid - Main / Brush All 9 988A Plug Bracket All 0 8A Upper Cable, Asm. L series 8409A Sleeve L series 44A Cable Spring L series 80A Cable Assembly Spring L series 4 9A Lower Electrical Panel All 409A Relay - Squeegee Up / Down L series 40A Solenoid - Vac All 980 Washer All 8 8004A Shoulder Screw All 9 4C Traverse, Control Board All 40 999 Screw, 8- x.4 Pn 4 All 4 40B Rear Cover L series 48B Rear Cover S series 4 89A Screw,.-0 x. Pn All 4 800A Washer All 44 980 Washer, Lock 4 All 4 880A Screw, ¼-0 x /4 Hex All 4 84A Screw, 8- x /8 PN L series 4 99 Trim, 4½" & 8" All 48 8A Washer, Nylon ¼x¼x / 0-4 L series 49 84A Washer, Nylon ½x¼x /8 L series 0 984A Clamp, Metal /8 All 09A Label, w/brake Warning 080A Label, w/o Brake Warning 9009 Rivet All 80A Stud, ¼-0 8 All 4 440A Diode All 4A Insert L series 4A Insert 4 S series 44A Insert All 0A Hose Bracket All 8 99 Screw, 0- x ½ 4 All 9 998 Screw L Series 0 909 Nut L Series 4A Label L Series A Label S Series 94B Label, Traverse All A Serial Tag All 4 800A Rivet, Pop All CLARKE TECHNOLOGY Operator's Manual - Encore S8/L8/S/L/S8/L8-4 -
Brush Motor #40A (S, L8, S8) Brush Motor #40A (L8, L, S8) Seam Location 4 4 Rotation 8 9 0 Ref # Part No. Description Qty 40A 40A 48A Stator Assembly (w/magnets & Clips) x 44A Stator Assembly (w/magnets & Clips) x 40A Armature Asm.(w/B.E. & F.E. bearings) x 408A Armature Asm.(w/B.E. & F.E. bearings) x 904 Bearings B.E. x x 4 900 Bearing F.E. x x 840A Commutator Bracket Assembly x x (w/brush BRD Assembly Leads) 00A Commutator Bracket x x 480A Strain Relief x x 8 94 Brush Board Screw x x 9 0A Brush Board Asm. (w/springs & brushes) x x 0 4489 Brush Spring 4 x x 408A Brush Assembly 4 x x A Lead Assembly, Positive x x A Lead Assembly, Negative x x 4 980A Helical Washer x x 0A Thru Bolt x x 44809A Shaft Key x x 48A B.E. Bracket Assembly (Gear Box) x x Page -4- CLARKE TECHNOLOGY Operator's Manual -Encore S8/L8/S/L/S8/L8
Gear Box #48A 0/9 9 8 4 Ref # Part No. Description Qty 84A Ring, Snap 04 Seal, Oil, Small 00A Cap End 4 8A O'Ring A Bearing, Large 8A Shaft & Gear, Gearbox 900 Bearing, Small 8 488A Housing 9 844A Seal, Oil Large NI Darina Grease 4oz. CLARKE TECHNOLOGY Operator's Manual - Encore S8/L8/S/L/S8/L8-4 -
Vac Motor Assembly #409A 0/9 8 4 4 8 9 4 9 0 4 Ref # Part No. Description Qty 9A Clip (optional) 4809A Housing 90A Fan 4 80A Screw - 8- x /8 4 4080A Carbon Brushes 94A Clamp 08A Bracket 8 00A Disc 9 909 Bearing - Ball 0 9048 Bearing - ball, radial Ref # Part No. Description Qty 980A Washer - neoprene 00A Bracket and shell 80A Spacer 4 94A Fan - Rotating 80 Spacer 908A Fan - Stationary 80 Shell 8 99A Fan, Air Seal 9 99A Fan, Stationary Page -44- CLARKE TECHNOLOGY Operator's Manual -Encore S8/L8/S/L/S8/L8
Volt Battery Charger 0/9 WARNING: All electrical repairs must be performed by qualified personnel only. PARTS LIST FOR BATTERY CHARGERS 400A - Volt D.C., A, Volt A.C., 0 Hz 400A - Volt D.C., A, 0 Volt A.C., 0 Hz 400A - Volt D.C., A, 0 Volt A.C., 0 Hz 404A - Volt D.C., A, Volt A.C., 0 Hz 40A - Volt D.C., A, 0 Volt A.C., 0Hz Charger Model Number 400A 400A 400A 404A 40A Ref # Description Part # Part # Part # Part # Part # Charger Case 40A 404A 99A 49A 8A Transformer 48400A 484A 4840A Ref Ref Electronic Timer Kit 40A 40A 40A 40A 40A 4 Capacitor, Mfd., 0 V.A.C. 9 9 9 9 9 Heat Sink Assembly 9 9 9 40A 40A Ammeter 4000A 4000A 4000A 400A 400A Fuse Assembly 98 98 98 404A 404A 8 Strain Relief, A.C. Cord 8 8 8 4 4 9 Strain Relief, D.C. Cord 4 4 4 0 0 0 D.C. Cord Assembly 9A 9A 9A 40A 40A A.C. Cord Assembly 94A 90894 90894 94A 8A D.C. Plug 98 98 98 98 98 D.C. Plug Lock Key 900 900 900 900 900 CLARKE TECHNOLOGY Operator's Manual - Encore S8/L8/S/L/S8/L8-4 -
CLARKE TECHNOLOGY Encore S8/S/S8 Electrical Schematic Page -48- CLARKE TECHNOLOGY Operator's Manual -Encore S8/L8/S/L/S8/L8
CLARKE TECHNOLOGY Encore S8/S/S8 Connection Diagram /99 CLARKE TECHNOLOGY Operator's Manual - Encore S8/L8/S/L/S8/L8-49 -