SOUTHWEST OILFIELD PRODUCTS, INC. MUD PUMP EXPENDABLE PARTS LIST SOUTHWEST 8482-A FLUID END FOR NATIONAL 14-P-220 MUD PUMP PERFORMANCE CHART PUMP MAX MAX STROKE LINER SIZE IN INCHES MODEL I.H.P. S.P.M. LENGTH 5 5 ½ 6 6 ½ 7 7 ½ 8 8 ½ 9 14-P-220 2200 105 MAX-P.S.I. 7500 7475 6285 5360 4615 4025 3535 3130 2795 14 G.P.R. 3.57 4.32 5.14 6.03 7.00 8.03 9.14 10.31 11.57 G.P.M. @ 105 R.P.M 374.9 453.6 539.7 633.15 735 843.2 959.7 1082.6 1214.9 NOTE: I.H.P.= INPUT HORSE POWER S.P.M.= STROKE PER MINUTE P.S.I.= POUNDS PER SQUARE INCH G.P.R.= GALLONS PER REVOLUTION *MAX P.S.I. CALCULATIONS DO NOT EXCEED MAXIMUM FLUID END PRESSURE RATINGS BASED ON 100% VOLUMETRIC EFFICIENCY AND 90% MECHANICAL EFFICIENCY Page 1 of 10
Page 2 of 10 10/15/15
8 7 6 5 4 3 2 1 79 23 64 " D 3 39 4 " D 10000# 5-1/8" BLIND FLANGE BX-169 RING JOINT GASKETS Page 3 of 10 C 10 1 4 " C 10"-150# ANSI FLANGES B B 89" 1 44 2 " 1 10 2 " 17 3 4 " 36 3 4 " A UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES TOLERANCES: FRACTIONAL 1/64 ANGULAR: 0.5 DECIMAL +.005 / -.000 ALL FILLETS & RADII - 1/16 MAX CHAMFERS 1/16 X 45 MAX SURFACE FINISH 125 RMS MAX CONCENTRICITY NOT TO EXCEED.005 T.I.R. BREAK SHARP CORNERS 1/32 X 45 MAX DRAWN BH CHECKED JM DATE 09/13/2013 DATE 09/13/2013 TITLE: SOUTHWEST OILFIELD PRODUCTS 10340 WALLISVILLE ROAD, HOUSTON,TX 77013 PIPING LAYOUT FOR NATIONAL 14-P-220 SWFE W/ EXTERNAL DISCHARGE CONNECTORS A MATERIAL N/A HEAT TREAT N/A THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF SOUTHWEST OILFIELD PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF SOUTHWEST OILFIELD PRODUCTS IS PROHIBITED. SIZE B DWG. NO. 8482A-APL REV SHEET 1 OF 1 8 7 6 5 4 3 2 1
FLUID END TYPE MODEL OF PUMP SIZE OF PUMP SOUTHWEST 7500 P.S.I. NATIONAL 14-P-220 9 X 14 ITEM NO. PART NO. DESCRIPTION QTY. REQ D 8482-A FLUID END ASSEMBLY: (CONSISTS OF ITEMS 3, 4, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 32, 33, 34) 1 6382G-XX LINER (REFER TO GUIDE FOR ORDERING CHART FOR TYPE (G); (Y); AND FOR BORE SIZE (XX)) 3 2 2930-XX LINER SEAL 3 3 8482-4 WEARPLATE 3 4 2930-09 WEARPLATE & MODULE SEAL 6 5 XX-BYY PISTON (REFER TO GUIDE FOR ORDERING CHART FOR SIZE (XX) AND FOR TYPE (YY)) 3 6 568-225 PISTON O-RING 3 7 6282W32 PISTON ROD (W/ ELASTIC STOP NUT) 3 8 API-4ESN PISTON ROD ELASTIC STOP NUT 3 9 6282-1 SUB ROD 3 10 6282CWY ROD CLAMP (CONSIST OF 10A, 10B, 10C) (FOR CLAMP ONLY USE 6282C) 6 10A 1200H30 HOSE (1/2 X 30 WITH ½ MALE X 3/8 MALE CONNECTIONS) 6 10B 1200160 PIPE (3/8 X 16 GALVANIZED AND THREADED ON ONE END) 6 10C 4020-29 ROD CLAMP BOLT (3/4-10 GRADE 8 BOLT WITH LOCK NUT AND WASHER) 12 11 6200G82 PONY ROD 3 12 SEE PAGE VALVE 6 13 SEE PAGE VALVE INSERT (IF REQUIRED) 6 14 SEE PAGE VALVE SPRING 6 15 SEE PAGE VALVE SEAT 6 SWTM1700 HYDRAULIC SEAT PULLER KIT COMPLETE (REFER TO TOOLS SECTION IN CATALOG) 1 4482A VALVE COVER ASSEMBLY (CONSIST OF ITEMS NO. 16-23) 6 16 4482 THREADED FLANGE 6 17 4582 SCREW GLAND 6 18 4682A PLUG (COMPLETE WITH VALVE GUIDE, BUSHING, AND SCREWS, AND BUSHING) 6 19 P113 HP VALVE COVER PLUG NITRILE SEAL 6 20 4782R VALVE GUIDE (COMPLETE W/ BUSHING #4700I) 6 21 4700I VALVE GUIDE INSERT (ALSO AVAILABLE IN URETHANE PART# 4700IU) 6 22 4019-75 VALVE GUIDE SCREW 24 23 4015-54 VALVE COVER STUD (WITH SW PART# HHN1500-6 1 ½-6 HEAVY HEX NUT) 84 Page 4 of 10
FLUID END TYPE MODEL OF PUMP SIZE OF PUMP SOUTHWEST 7500 P.S.I. NATIONAL 14-P-220 9 X 14 ITEM NO. PART NO. DESCRIPTION QTY. REQ D 24 4019-24 POWER END STUD (WITH SW PART# HHN1500-6 1 1/2-6 HEAVY HEX NUT) 30 25 6482 LINER RETAINER FLANGE 3 26 4015-52 LINER RETAINER STUD (WITH SW PART# HHN1250-7 1 ¼-7 HEAVY HEX NUT) 18 27 6582 LINER RETAINER NUT 3 28 4019-74 SUCTION MODULE STUD (WITH SW PART# HHN2000-8 2-8 HEAVY HEX NUT) 18 29 4018-19 SUCTION MANIFOLD CAP SCREW 24 30 8582 SUCTION MANIFOLD 1 31 AJO326 SUCTION MANIFOLD SEAL 3 32 8482-2S SUCTION MODULE 3 33 8482-1D DISCHARGE MODULE 3 34 8488-5 DOWEL PIN 6 35 2982-3 DISCHARGE END ADAPTER SEAL 2 36 4017-4 DISCHARGE END ADAPTER CAP SCREW 24 37 BX169 RING JOINT 2 38 4020-21 BLIND FLANGE STUDS (WITH SW PART# HHN1125-7 1-1/8-7 HEAVY HEX NUTS) 24 39 2982-2 DISCHARGE CONNECTOR SEAL 4 40 8382-1 DISCHARGE CONNECTOR 2 41 8382-3 DISCHARGE CONNECTOR BACK-UP RING 2 42 4018-18 DISCHARGE CONNECTOR CAPSCREW 16 43 2982-1 DISCHARGE CONNECTOR END SEAL 2 44 8382-2 DISCHARGE CONNECTOR ADAPTER 2 45 8382-4 DISCHARGE END FLANGE ADAPTER 2 ** POLYURETHANE SEALS AVAILABLE** Page 5 of 10
Page 6 of 10 10/15/15
SOUTHWEST 7500 PSI NATIONAL 14-P-220 GUIDE TO ORDERING PISTONS LINERS LINER GASKETS SIZE FAIL-SAFE DUAL-DURO BLACK CAT GRAYLOY ZIRCONIA RUBBER URETHANE 5" 81BFS 81BDD 81BBC 6382G1 6382ZIR1 2930-1 2930-1U 5 1/2" 83BFS 83BDD 83BBC 6382G3 6382ZIR3 2930-3 2930-3U 6" 85BFS 85BDD 85BBC 6382G5 6382ZIR5 2930-5 2930-5U 6 1/2" 87BFS 87BDD 87BBC 6382G7 6382ZIR7 2930-7 2930-7U 7" 89BFS 89BDD 89BBC 6382G9 6382ZIR9 2930-9 2930-9U 7 1/2" 92BFS 92BDD 92BBC 6382G11 NA 2930-11 2930-11U 8" 94BFS 94BDD 94BBC 6382G13 NA 2930-13 2930-13U NOTE: DUAL-DURO AND GRAYLOY ARE REGISTERED TRADEMARKS OF SOUTHWEST OILFIELD PRODUCTS. Page 7 of 10
TYPE SOUTHWEST (Full Open) FULL OPEN-ROUGHNECK (Cast N Place Insert Valve) FULL OPEN-ROUGHNECK (High Temp) FULL OPEN-ROUGHNECK (w/replaceable Urethane Insert) 3 WEB DOUBLE ANGLE O-RING 3 WEB (High Temp) 3 WEB STANDARD PLATE 4 WEB 4 WEB (High Temp) VALVES & SEATS (8482-A) 14-P-220 VALVE INSERT SPRING STAINLESS SPRING SWND-8V2 N/A SW5710-115L N/A SWND-8S7 SWND-8V2HC N/A SW5710-115L N/A SWND-8S7 SEAT PULLER HEAD SWND-8PH SWTM48-SN SWND-8PH SWTM48-SN N/A N/A N/A N/A N/A N/A SWR0500120 SWR0515831 SWR0520503 SWR0520504 SWR0504845 SWTM3-8 SWR050012022 SWR051583101 N/A N/A N/A N/A SWR0505109 SWR0504897 N/A SWR0514423 SWR0504845 SWTM3-8 SWU5B-23 SWUDD-8B SW5710-32 N/A SW8DD-B7 SWTM4-8 N/A N/A N/A N/A N/A N/A PULLER HEAD STYLE SPLIT JAW PANCAKE SPLIT JAW PANCAKE SPLIT JAW 3 J HOOK 4 J HOOK PANCAKE SPLIT JAW 3 J HOOK 4 J HOOK Page 8 of 10
TORQUE SPECIFICATIONS FOR 8482-A SOUTHWEST FLUID END ASSEMBLY NATIONAL 14-P-220 7500 P.S.I. TORQUE TYPE (EXPRESSED IN FOOT-POUNDS) PART NUMBER DESCRIPTION COPPERCOTE MOLY GREASE DRY (NOT RECOMMENDED) API-4 ESN PISTON NUT NO MORE FORCE THAN ONE MAN ON 3' WRENCH/CHEATER COMBINATION 4019-77 ROD CLAMP BOLT 150 MAXIMUM 4019-75 VALVE GUIDE SCREW 106 159 212 4015-54 VALVE COVER STUD 1208 1752 2417 4019-24 POWER END STUD 1150 1668 2301 4015-52 LINER RETAINER STUD 669 940 1338 4019-74 SUCTION MODULE STUD 3463 5021 6925 4018-19 SUCTION MANIFOLD CAP SCREW 215 322 430 4018-18 DISCHARGE CONNECTOR CAP SCREW 53 80 107 Page 9 of 10
8482-A National 14-P-220 7500 PSI FLUID END REVISION SUMMARY REVISION DATE REASON OF CHANGE REV A 1/20/15 Changed Item No. 10C Part No. 4019-77 to 4020-29 what shows in MASS. REV B 10/14/15 ADDED PART NO. 4482A VALVE COVER ASSEMBLY Southwest Oilfield Products 10340 Wallisville Road, Houston, TX 77013 Office 713-675-7541 Page 10 of 10