JTC-1147 6" CHAIN WRENCH Handle: 6" Chain: 18" (400mm) Handle: 20" Chain: 25" JTC-1149 20" CHAIN WRENCH JTC-1150 12" STRAP WRENCH Handle: 12" Strap length: 36"
JTC-1355 EUROPEAN DOOR HINGE / HANDLE KIT For removing rear door hinge and handle o T30 x 250mmL BENZ 220C and NEW S. o T20 x 210mmL VW and BENZ o Bits M4, M8, M10, T40, T45 x 25mm 1998 & newer VW golf, Jetta, Passat & new Bettle o Ratchet Handle x 240mm JTC-1728 ANGLE TIP LOCK RING PLIERS Spread snap lock rings on brakes, transmissions, pedal shafts, clutch shafts & machine tools. Jaws have deep serrations on the outside of tip to help lock rings securely. Spreading : 3.5~28mm Total length : 225mm JTC-3002 36" JUMBO PRY BAR Chrome-molybdenum steel. Go-through alloy steel square. Rugged firm grip designed plastic handle. Excellent for prying engine, cylinder head, transmission cases, manifold and drive line components. Flat tip.
JTC-3003 36" JUMBO PRY BAR (BEND) JTC-3117 4PCS PRY BAR SET JTC-3207 IMPACT DRIVER SET Chrome-molybdenum steel. Go-through alloy steel square. Rugged firm grip designed plastic handle. Excellent for prying engine, cylinder head, transmission cases, manifold and drive line components. Curved tip. Spec.: o 7/16" x 24"L o 7/16" x 18"L o 3/8" x 12"L o 1/4" x 8"L Bits Material: S2 o 4 Bits x 36mml: PHILLIPS NO. 2, NO. 3 SLOTTED θ8m, 10mm o 28 Bits x 80mml: PHILLIPS NO. 2, NO. 3
JTC-3311 90 DEGREE EXTRA LONG NEEDLE NOSE PLIERS Made from CR-MO material to provide a high strength level and uniform hardness. The design of pliers means reach and application advantage at every turn. Long, slim jaws and flash-riveted joints enable pliers to reach into recessed areas. Spec: 90 BEND Length: 11" JTC-3312 EXTRA LONG ROUND JAWS PLIER Made from CR-MO material. Suitable for using on hoses, spark plug wires, etc. Ø: 8mm (5/16") Length: 11" JTC-3313 EXTRA LONG ROUND JAWS PLIERS Made from CR-MO material. Suitable for using on hoses, spark plug wires, etc. Ø: 13mm (1/2") Length: 11"
JTC-3314 EXTRA LONG ROUND JAWS PLIERS JTC-3471 10-1/2" SNAP RING PLIERS SET JTC-3504 9 PCS LONG HEX SET Made from CR-MO material. Suitable for using on hoses, spark plug wires, etc. Ø: 19mm (3/4") Length: 11" Featured replaceable tips and have a spring ratchet locking mechanism to hold circlip securely against tension. Offset tips make it easier to facilitate circlip. o 2 of each 2.75 mm tips in o, 15, 45, 90 o 2 of each 3.0 mm tips in o, 15, 45, 90 Length: 10-1/2" (265mm) Spread: o Internal: 60mm ~100mm o External: 38mm ~ 85mm Plastic holder professionally designed for nice installation and convenience usage. Extra-long arm series can save strength and time for enable pleasant operation. Material: S2 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10mm
JTC-3505 9 PCS LONG BALL POINT HEX SET JTC-3506 9 PCS LONG BALL POINT HEX SET JTC-3313 58 PCS POWER BIT SET Work in hard to reach areas. Faster inserting and removing. Full depth engagement. Material: S2 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10mm Special offer for CR-V material JTC-3508A Work in hard to reach areas. Faster inserting and removing. Full depth engagement. Material: S2 1/16", 5/64", 3/32", 1/8", 5/32", 3/16", 1/4", 5/16", 3/8" Material: S2 o 9 pcs 30mmL star power bit: T20, T25,T27, T30,T40, T45, T50, T55, T60 o 9 pcs 75mmL star power bit: T20, T25, T27, T30, T40, T45, T50, T55, T60 o 9 pcs 30mmL hex power bit: 4, 5, 6, 7, 8, 10, 12, 14, 17 o 9 pcs 75mmL hex power bit: 4, 5, 6, 7, 8, 9, 10, 12, 3/8" o 5 pcs 30mmL spline power bit: M5, M6, M8, M10, M12 o 8 pcs 75mmL spline power bit: M5, M6, M8, M9, M10, M12, M14, M16H o 5 pcs 75mmL ribe power bit: RM6, RM7, RM8, RM10, RM12 o 2 pcs 75mmL square power bit: 8, 10 o 1 pc 10mm(hex) x 3/8" Dr. Adapter o 1 pc 10mm(hex) x 1/2" Dr. Adapter
JTC-3629 90 DEGREE EXTRA LONG NEEDLE NOSE PLIERS JTC-3701 90 DEGREE ANGLE SCREWDRIVER SET JTC-3819 EXTRA LONG NEEDLE NOSE PLIERS Go-through alloy steel square. Perfect for fastening jobs in confined Made from CR-MO material to Rugged firm grip designed plastic handle. areas. provide a high strength level and Excellent for prying engine, cylinder head, transmission cases, manifold and drive line components. Features a quick-set handle holding in all angle for efficient performance and 1/4" hex shank can be used with power driver or by included hand driver. uniform hardness. The design of pliers means reach and application advantage at every turn. Long, slim jaws and flash-riveted joints enable pliers to reach into #1 & #2-25m/m bit included. recessed areas. Spec: 0 STRAIGHT Length: 11"
JTC-3820 EXTRA LONG NEEDLE NOSE PLIERS Made from CR-MO material to provide a high strength level and uniform hardness. The design of pliers means reach and application advantage at every turn. Long, slim jaws and flash-riveted joints enable pliers to reach into recessed areas. Spec: 45 BEND Length: 11" JTC-3924 9 IN 1 STAR KEY SET (TAMPER PROOF) Made from SNCM8660 material. Long shank to reach confined areas or increase torque. With double end tamper resist. T10H, 15H, 20H, 25H, 27H, 30H, 40H, 45H, 50H. JTC-3925 9 PCS STAR SCREWDRIVER SET (TAMPER PROOF) Chrome molybdenum steel with heat treated blade & magnetic tip Special design with hole in the head to fit the special screws T8H x 100mm, T9H x 100mm, T10H x 100mm, T15H x 125mm, T20H x 125mm, T25H x 125mm, T27H x 150mm, T30H x 150mm, T40H x 150mm.
JTC-3933 42 PC POWER BIT SET Material: S2 o 8 pcs 30mm star power bit:t20, T25, T27, T30, T40, T45, T50, T55 o 8 pcs 75mm star power bit:t20, T25, T27, T30, T40, T45, T50, T55 o 7 pcs 30mm hex power bit:4, 5, 6, 7, 8, 10, 12mm o 7 pcs 75mm hex power bit:4, 5, 6, 7, 8, 10, 12mm o 5 pcs 30mm spline power bit:m5, M6, M8, M10, M12 o 5 pcs 75mm spline power bit:m5, M6, M8, M10, M12 o 1 pcs 10mm (hex) x 3/8" Dr. Adapter o 1 pcs 10mm (hex) x 1/2" Dr. Adapter JTC-4066 LARGE LOCKING RING PLIERS Applicable: Large rings on drive shafts in earth-movers and construction vehicles. Tip form: Interchange, wide, milled. Tip size (mm):3.5 x 8mm; spreading 8-75mm Total length: 330mm JTC-4093 S TYPE WRENCH (12MM) Special S angle designed for better operation. Use for installing and removing the door hinge screws. Size: 12mm; 12PT Applicable: TOYOTA, NISSAN, HONDA, MITSUBISH, SUZUKI, etc.
JTC-4754 DOOR HINGE BOLTS REMOVER KIT Special angle wrench design to quickly and easily loosen and tighten the bolts in door hinges. Also adjusts the toe on the rear axle. o 7 pcs bits: M8, M10, M12, T30, T40, T45, T50 o 1 pc special angle 3/8"DR. wrench o 1 pc 45 8mm gear wrench Applicable: VW, AUDI, BENZ, etc. JTC-5610 55 PCS MINI RATCHET BITS SET Bit material: S2 Length: 20mm Ratchet length: 20mm o 1 pc mini ratchet o 1 pc ratchet screwdriver o 1 pc magnet extension bar o 11 pc STAR T6, T7, T8, T9, T10, T15, T20, T25, T27, T30, T40 o 11 pc STAR (tamper-proof) o 6 pc HEX H2, H2.5, H3, H4, H5, H6 o 8 pc 5PT. STAR(tamper-proof) TS8H, TS10H, TS15H, TS20H, TS25H, TS27H, TS30H, TS40H o 4 pc Slotted FD3, FD4, FD5, FD6, FD7 o 4 pc Y-type 1-2-3-4 o 4 pc X-type 6-8-10 JTC-5709 EXTRA LONG RETAINING RING PLIER (INTERNAL STRAIGHT) Length: 255mm Tip length: 75mm Tip diameter: Ø 1.2mm
JTC-5710 EXTRA LONG RETAINING RING PLIER (INTERNAL BENT) JTC-5711 EXTRA LONG RETAINING RING PLIER (EXTERNAL STRAIGHT) JTC-5712 EXTRA LONG RETAINING RING PLIER (EXTERNAL BENT) Length: 255mm Bent Tip length: 65mm Tip diameter: Ø 1.2mm Length: 225mm Tip length: 75mm Tip diameter: Ø 1.2mm Length: 225mm Bent Tip length: 65mm Tip diameter: Ø 1.2mm
JTC-5713 12" EXTRA LONG NEEDLE NOSE PLIER (LONG JAWS) Long jaws design for better reaching into recessed areas. Length: 12" (300mm) Jaw length: 170mm JTC-5714 7" WIRE CUTTER Applicable: o Wire: Ø 1.5mm o Copper: Ø 4mm Length: 165mm JTC-5715 POWER RIBE BIT SET Bit material: S2 o 10 pcs 30mmL ribe power bit: RM5, 6, 7, 8, 9, 10, 11, 12, 13, 14 o 11 pcs 100mmL ribe power bit:rm5, 6, 7, 8, 9, 10, 10.3, 11, 12, 13, 14 o 2 pcs Adapter: 10mm (Hex) x 1/2"DR., 10mm(Hex) x 3/8"DR.
JTC-5909 16" EXTRA LONG HANDLE NEEDLE NOSE PLIERS (0 ) Made from CR-MO material to provide a high strength level and uniform hardness. The design of pliers mean reach and application advantage at every turn. Long, slim jaws and flash-riveted enable pliers to reach into recessed areas. Spec: Straight Length: 16" JTC-5910 16" EXTRA LONG HANDLE NEEDLE NOSE PLIERS (45 ) Made from CR-MO material to provide a high strength level and uniform hardness. The design of pliers mean reach and application advantage at every turn. Long, slim jaws and flash-riveted enable pliers to reach into recessed areas. Spec: 45 Bent Length: 16" JTC-193810 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 10mm
JTC-19382 FLEXIBLE SHAFT NUT DRIVERS JTC-19385 FLEXIBLE SHAFT NUT DRIVERS JTC-19386 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose Spec: 1/4" clamp. clamp. Spec: 5mm Spec: 6mm
JTC-19387 FLEXIBLE SHAFT NUT DRIVERS JTC-19388 FLEXIBLE SHAFT NUT DRIVERS JTC-11R LOCKING "C" CLAMP Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose Cr-MO drop forget jaws. Bodily heat-treated. Spec: 7mm clamp. Welding brazed. Spec: 8mm Nickel plated. Spec: 11" Function: C Shaped plier
JTC-18R LOCKING "C" CLAMP Cr-MO drop forget jaws. Bodily heat-treated. Welding brazed. Nickel plated. Spec: 18" Function: C Shaped plier JTC-3210S 50 PCS GO-THROUGH SCREWDRIVER SET 50 pcs The set could be hanged on the display board. ITEM SPEC ITEM SPEC 3707 1-1/2" two-way 3713 8" x 8Θ x x 4PCS 5PCS 3708 4" x 6mm x 5PCS 3709 4" x 6mmΘ x 5PCS 3710 6" x 8mm x 5PCS 3711 6" x 8mmΘ x 5PCS 3210 12" x 10Θ x 4PCS 3804 101 3 x 3"Θ x 6PCS 3808 102 5 x 12"Θ x 6PCS 3811 107 6 x 12" x 5PCS JTC- 3470S 44 PCS HEAVY DUTY SCREWDRIVER SET 44 The set could be hanged on the display board. ITEM SPEC ITEM SPEC 3463 3.0 x 75Θ x 3467 6.5 x 100Θ x 6PCS 8PCS 3464 #0 x 75 x 6PCS 3465 6.5 x 38Θ x 4PCS 3766 #2 x 38 x 4PCS 3468 #2 x 100 x 8PCS 3469 8.0 x 150Θ x 4PCS 3470 #3 x 150 x 4PCS