Effective, simple!!! KehrFix made in Germany Simply effective!!! Have you sometimes asked yourself, why your employees are not using the beautiful, new rotational sweeper that you have bought? You spent a lot of money and now it is tucked away in the most remote corner. The reason for non-usage is the inconvenient mounting and dismounting. If something has to be cleaned they continue to use the broom. Again and again you hear that they are faster with it. If at least the broom was a little bit bigger.. Congratulations! We can help you! The KehrFix block brooms are a professional choice for simple and effective sweeping and cleaning. The robust KehrFix has been developed and produced in order to perform these tasks quickly and thoroughly in all conceivable areas of application. KehrFix products are high-quality, durable, maintenance-free and universally applicable sweeping systems. They are the alternative to rotational sweeping systems. The KehrFix is suitable for loose or clinging dirt, stone chippings, mud or fluid faeces, on flat or uneven surfaces (e.g. cobble stones) and even for brushing gravel and sand as well as for brushing snow. Not using any rotating parts is a contribution to the improvement of health and safety. The considerably lower dust formation is one of the pleasant side effects. No debris is being slung away anymore. The KehrFix sweeping brushes are available in different widths of 1.25m to 2.90m and a configuration of 6 20 bristle rows and can be mounted to almost any existing carrier vehicle. Special sizes are available on request. If you need help or advice with the choice of a KehrFix sweeping brush or if you would like to know where you can purchase KehrFix sweeping brushes, just contact us we will be glad to help you! Producer KehrFix Weber Baumaschinen und Fahrzeuge GmbH Rohrbacher Weg 2 57339 Erndtebrück tel.: 02753 60398-0 fax: 02753 60398 28 email: info@mucktruck-deutschland.de
Which advantages does the use of KehrFix offer? time saving, quick mounting and dismounting, maintenance-free, lightweight, better utilisation of carrier vehicle, little dust during operation, does not spray, robust and insensitive, no rotating or moving parts, simple use, no hydraulics and no power take-off shaft required, no electrics required, no drive belt or drive chains, no waste, cables, stems, cords or animal hair get stuck in the bristles, easy to clean by tapping or hosing, not susceptible to breakdown, quick change of bristle rows, costs for replacement bristle rows about 4 times lower compared to a rotating sweeping system, durable (service life of the bristles = up to 1,000 km on asphalt), high benefit with lowest running costs, broom body powder coated, serial adaptor powder coated or galvanised, curb deflector fitted as standard, made in Germany Which carrier vehicles are suitable for the KehrFix? Tractors, municipal vehicles, forklift trucks, all terrain forklift trucks, telescopic forklifts, wheel loaders, excavators but also easy to fit to: quads, transporters, RTV's, pick-ups, bobcats and many other commercial vehicles, Which materials can be moved by the KehrFix? the KehrFix is suitable for sweeping and brushing aside soft, fluid and solid materials (snow, saw dust, metal chips, leaves, sand, grit, stone chippings, grain, potatoes, fertiliser, bark mulch, wood chips, wooden pellets, soil, gravel, mud and liquid manure), but also scrap, glass splitter, and other waste,
Which are the most important areas of application for the KehrFix? construction sites, construction goods trading sites, agricultural goods trading sites, parking spaces, farms, biogas plants, medium-size enterprises, golf courses, recycling yards, horse ranches, tournament sites, storage areas, concrete or asphalt surfaces, sawmills, car dismantlers, courtyards, paths, streets, winter road maintenance and much more, Has the KehrFix proven itself in any particular applications? brushing of sand during paving works, cleaning of faeces on farms, brushing snow or clearing snow even on very uneven surfaces, sweeping of grain during goods handling in agricultural trading, moving of feeding stuff on farms, cleaning of silo plates, usage on golf courses, maintenance works on artificial turf pitches, biogas plants, recycling yards, glass manufacturers, medium-sized enterprises, Technical data model working width weight bristle rows bristle height m kg mm KF125-6 1.25 36 6 280 KF150-6 1.50 42 6 280 KF150-9 1.50 67 9 280 KF200-9 2.00 98 9 280 KF150-12 1.50 94 12 280 KF200-12 2.00 123 12 280 KF250-12 2.50 143 12 280 KF290-12 2.90 181 12 280 KFS250-14 2.50 157 14 (up to 20) 280 KFS290-14 2.90 195 14 (up to 20) 280 If you require a different working width or a higher number of bristle rows, please call us. We will work together to find a solution. What do I need to pay particular attention to when using the KehrFix? When sweeping or pushing, it should be ensured that the brush is placed horizontally to the ground, if possible, so that all bristle rows have ground contact. A smooth, roaring operating noise can be heard. In order to get ideal results, the number of bristle rows should not be too low. Is a dirt collector being offered for the KehrFix? No! The KehrFix has been developed with the classical principal of sweeping with manual dirt collection in mind. The debris can be pushed into a pile and can then be collected.
Are there any videos that show the KehrFix in operation? Yes! The KehrFix can be seen in operation in different areas at the following YouTube addresses: KehrFix as an effective alternative to the snow plough: http://www.youtube.com/watch?v=tsb35aqsp14 KehrFix in the most difficult applications: keyword: biogas plant, silage: http://www.youtube.com/watch?v=ufdo8p3whs8 KehrFix in winter road maintenance, pivoting on a lift truck: http://www.youtube.com/watch?v=mhi66e_bwry KehrFix in the wood-processing industry: http://www.youtube.com/watch?v=6np-lfzrqja The KehrFix is equipped, as standard, with a galvanised curb deflector. How are the bristle rows changed? Step 1 Step 2 Step 3 Step 4 removing a curb folding a curb replacement of attaching a curb deflector deflector individual bristle rows deflector Is there further development regarding the KehrFix? Yes, the KehrFix is constantly being improved. The special edition 14-20 was developed in order to clean even bigger surfaces optimally. Only the first 7 and the last 7 bristle rows are fitted. The middle 6 bristle rows stay empty. Thereby the self-rotation of fine dust particles is considerably reduced. Since autumn 2012, the KehrFix is completely galvanised. Add-on adaptors are also constantly improved and adjusted to the clients' requirements.
KehrFix add-on adaptors In order to adjust the KehrFix simply and quickly to the different carrier vehicles, a number of adaptors has been developed. The following list gives an overview. If you do not find the mounting option that you require, or if you have a specific idea, just contact us we will be glad to help you. The pallet fork handler mounting, suitable for all KehrFix, is the most simple and inexpensive mounting option. The use of KehrFix is possible with it on all carrier vehicles with pallet clamps. The locking is done manually with socket bolts and safety splints. KF-PGAI The multi-pallet fork handler mounting, also suitable for all KehrFix, is a further development for the use of the KehrFix on carrier vehicles with pallet clamps. The locking is done with a lobster clasp or by moving the tines laterally. KF-MPGA Moreover, it forms the basis for further mounting options. The three-point extension set (middle component), in combination with the multi-pallet fork handler mounting, allows the mounting of the KehrFix to a carrier vehicle with a classical three-point mounting system. KF-ESetDP (Attention!!! Can only be used in combination.) The multi-mounting for gravel shovel/silage shovel/gripper/4 in 1 (image similar). Can also be mounted to the multi-pallet fork handler mounting. Usage is then from the front or from behind. KF-MA Application example 1 Multi-mounting on normal shovel KF-MA-1
Application example 2 Multi-mounting with adaptor for Kramer (image similar) KF-MA-2 Application example 3 Multi-mounting on grabbing-shove (image similar) KF-MA-3 Application example 4 Multi-mounting on 4 in 1 shovel (image similar) KF-MA-4 The extension set K-multi-mounting allows the use of the KehrFix on individual vehicles like Weidemann, Kramer or other carrier vehicles. These adaptors are offered/produced individually. The image shows multi-mounting plus adaptor for Kramer. KF-ESetSpezial The add-on set for grapple rake allows the use of the KehrFix grapple rake shovels. Image here without bite rubber and without raising sets. Extension to three-point is possible. KF-KG The Euro-mounting allows the use of the KehrFix on Euro-mounting adaptors. As an add-on, the extension set for three-point can be offered. KF-EA
The bale clamp mounting allows the use of the KehrFix on vehicles with bale clamps in the recycling industry. KF-BAll The pivot adaptor (currently only available for the pallet fork handler mounting KF-PGAI) enables the use of a slanted position of the KehrFix in 3 levels to the left and to the right. KF-S The new pivot adaptor has been developed for the use on winding roads in winter. KF-SAneu 3-point mounting solo without image KF-DPs