Installation Instructions NextGen Selectronic Integrated Faucet with Optional Above-Deck Mixing & SmarTherm Temperature Limiter CAUTION: Use only American Standard supplied transformers and cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. Product No.s & Options Specifications Faucet Installation Electrical Installation - Start-up / Maintenance -8 FAQ s / Troubleshooting 9 Parts 0 Certified to comply with ASME A.8. 07 AS America, Inc. MODEL NUMBERS 77.xx 77B.xx 77.xx 77B.xx 77.xx 77B.xx TE TO INSTALLER: Please give this manual to the customer after installation. To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@lixilamericas.com For Parts, Service, Warranty or other Assistance, please call (8) CRT-TEAM / (8) 78-8 (In Canada: -800-87-09) (In Toronto Area only: -90-0-09) 07 AS America Inc. M97 Rev.. (/7)
CAUTION: Use only American Standard supplied transformers and cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. Product No.s & Options Faucet Installation Electrical Installation - Start-up / Maintenance -8 FAQ s / Troubleshooting 9 Parts 0 0 AS America, Inc. MODEL NUMBERS 77.xx 77B.xx 77.xx 77B.xx 77.xx 77B.xx TE TO INSTALLER: Please give this manual to the customer after installation. To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@americanstandard.com For Parts, Service, Warranty or other Assistance, please call (8) CRT-TEAM / (8) 78-8 (In Canada: -800-87-09) (In Toronto Area only: -90-0-09) 0 AS America Inc. M97 (8/) Thank you for selecting American-Standard...the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping. Remove the fitting and loose items from the carton. The illustration below shows all the fittings and loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.. Installation Instructions. Spout Assembly (less mixing) a. Spout Assembly (mixing). Mounting Kit. " and 8" Deck plate (optional, must be ordered separately). Thermostatic Mixing Valve (optional, must be ordered separately). Inline Filter 7. Assembly Parts 8. Battery Back-Up Unit (optional, must be ordered separately) PWRX Power Kit POWER KITS SOLD SEPARATELY Plug-In AC Power Kit Hard-Wired AC Power Kit Multi-AC Power Kit PK00.WRK PK00.PAC PK00.HAC PK00.MAC DO T REMOVE PROTECTIVE FILM FROM SENSOR EYE UNTIL INSTALLATION IS COMPLETE. a DO T REMOVE PROTECTIVE FILM FROM SENSOR EYE UNTIL INSTALLATION IS COMPLETE. 7 Installation Instructions NextGen Selectronic Integrated Faucet with Optional Above-Deck Mixing & Temperature Limiter Battery Back-Up Kit 8 PK00.BBU 0XTMV070 Deck Plate Mixing Valve 77P.00 77P.800 M97 Rev.. (/7)
Roughing-in Dimensions Note: All plumbing and electrical wiring must be installed in accordance with applicable codes, regulations and standards. 7 mm (-7/8") FINISHED WALL OR BACKSPLASH CLEARANCE mm (min) - 7mm (max) (" min - " max) mm (-/") mm mm (-/") (") 8 mm (-7/8") 9 mm (-/") mm (-7/") CAUTION: Use only American Standard supplied transformers and cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. 8 mm (-/") 8 mm (-/8") 97 mm (-/") /8" COMPRESSION CONNECTORS RECOMENDED CONTROL BOX OR EQUIVALENT BY OTHERS " (0mm) SQ. X -/" (mm) DEEP -GANG ELECTRICAL BOX Appleton #SD OR EQUAL (BY OTHERS). (Used with Hard-Wired AC Transformer) RECOMMENDED TOOLS.. mm Hex Wrench (Included). Adjustable Wrench. Plumbers Putty or Caulking. Phillips Screwdriver. Tape Measure..0 mm Hex Wrench (Included) Fig. 0' SPOUT ASSEMBLY INSTALLATION; Fig. CAUTION Turn off hot and cold water supplies before beginning Fig. IMPORTANT: Do not use putty when installing faucet without escutcheon.. Make sure O-RING () is installed in spout base. IMPORTANT: Do not use putty when installing faucet without escutcheon.. If installing DECK PLATE () (optional): Apply a bead of putty to bottom edge of PUTTY PLATE (). Install SCREW () into the MOUNTING BASE OF THE FAUCET () and allign SCREW () with HOLE ().. Insert SUPPLY HOSES (), SHANK () and SENSOR CABLE () (only included in base model) through hole in DECK PLATE with PUTTY PLATE () and mounting surface. (OPTIONAL) PUTTY (If required). Assemble RUBBER WASHER (7), BRASS WASHER (8) and THREADED LOCKNUT (9) onto SHANK () from underside of sink or mounting surface. Hand tighten LOCKNUT (9).. Use a screwdriver to tighten SCREWS (0) on LOCKNUT (9). Work your way around LOCKNUT (9), tightening the screws slightly each time until all are snug to ensure even pressure. 7 8 9 MOUNTING SURFACE 0 TIGHTEN SPIN NUTS IMPORTANT: Do not use sealent on threads M97 Rev.. (/7)
ELECTRICAL INSTALLATION Fig. Product Page PWRX Power Kit (PK00.WRK) Plug-In AC Power Kit (PK00.PAC) Hard-Wired AC Power Kit (PK00.HAC) Multi-AC Power Kit (PK00.MAC) Important: All product with standard battery come with electrical connections preaseambled at the factory. No further action necessary. A PWRX 0 YEAR BATTERY SYSTEM; Fig. BRACKET INSTALLATION PWRK VERSION;. Connect PWRX BATTERY PACK () to SENSOR CABLE ().. Secure the connections by installing into CONNECTOR LOCKING DEVICE () as shown. Rotate the END CAPS () to secure the connection within the CONNECTOR LOCKING DEVICE ().. Determine the mounting location of the PWRX BATTERY PACK () by marking center lines as shown.. Place the BRACKET () on the horizontal center line and mark the location of the mounting holes to be drilled. HORIZONTAL C/L. Using /" diameter drill bit, drill two mounting holes aproximately " deep.. Install the two ANCHORS () provided into the mounting holes. 7. Place the BRACKET () over the ANCHORS () and secure with the SCREWS (7) provided. Do not overtighten. 8. Insert PWRX BATTERY PACK () into BRACKET (). VERTICAL C/L 7 M97 Rev.. (/7)
B AC VERSIONS (HARD-WIRED / PLUG-IN POWER SUPPLY); Fig. Fig. Important: Turn off power to outlet or electrical box. FOR PLUG-IN VERSION;. Connect PLUG-IN AC POWER SUPPLY () to one end of the SINGLE AC ADAPTER ().. Connect SENSOR CABLE () to the other end of the SINGLE AC ADAPTER ().. Connect PLUG-IN AC POWER SUPPLY () to wall outlet. 0' EXTENSION FOR HARD-WIRED VERSION;. Connect 0 EXTENSION CABLE () to HARD-WIRED AC TRANSFORMER ().. Connect SENSOR CABLE () to the other end of the 0' EXTENSION CABLE ().. Make Black and White power line connections to HARD-WIRED AC TRANSFORMER () and mount on ELECTRICAL BOX (). CAUTION: Use only American Standard supplied transformers and cable sets. Using non-as supplied cables, or cutting, splicing or modifying any components will void the warranty. WALL OUTLET " CONTROL BOX OR EQUIVALENT BY OTHERS () BLACK & WHITE POWER CONNECTIONS Do not connect power to transformer until installation of faucet is complete. Recommended Electrical Box or Equivalent by others (0mm) SQ. X -/ (mm) DEEP -GANG ELECTRICAL BOX Appleton #SD OR EQUAL (BY OTHERS). Fig. Unit # (Already Installed) Unit # Unit # Unit # BLACK & WHITE POWER CONNECTIONS MAXIMUM OF UNITS PER TRANSFORMER. 0' MAXIMUM CABLE LENGTH BETWEEN UNITS. C MULTI-AC VERSION (DAISY-CHAIN); Fig. Important: Disconnect the first unit s Multi-AC Adapter from power supply before making daisy-chain connections. Note: For Unit # electrical instructions, refer to Figure (above). For subsequent Units, refer to instructions below.... Connect one end of the 0' EXTENSION () to the available terminal of the previous unit s MULTI-AC ADAPTER (), and the other end to the single terminal of the current unit s MULTI-AC ADAPTER ().. Connect SENSOR CABLE () to either of the two available terminals of MULTI-AC ADAPTER ().. Repeat Steps above for each additional Unit, for a Max. of Units on one AC POWER SUPPLY. M97 Rev.. (/7)
Certified to comply with ASME A.8.M 00 American Standard M98808 To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S. customer's e-mail us at: faucetsupport@amstd.com For Parts, Service, Warranty or other Assistance, (In Toronto Area only: -90-009) D MAKE WATER SUPPLY CONNECTIONS; Fig.. Turn off hot and cold water supplies before beginning.. Install INLINE FILTER () on each wall supply outlet. Be sure that INLINE FILTER () is inserted in the correct direction. (See Illustration). Connect HOT FLEXIBLE SUPPLY (marked with red stripe) () to INLINE FILTER () on hot water control stop (). Connect COLD FLEXIBLE SUPPLY (marked with blue stripe) () to INLINE FILTER () on cold water control stop (). Use adjustable wrench to tighten connections. Do not over tighten.. Faucet supplies are " long from faucet base. Note; If additional supply length is required, installer must purchase those parts separately. Important; If SUPPLY HOSES (, ) are too long, loop as illustrated to avoid kinking. E INSTALL OPTIONAL MIXING VALVE; Fig. Note: An optional Thermostatic Mixing Valve (sold separately) may be installed on faucets 77X.XX & 77X.XX in addition to Above Deck Mixing valve. See setup diagram Fig.. Tee fitting is not supplied with Faucet or Thermostatic Mixing valve and must be purchased separately. If faucet inlet hoses will not reach water supplies, longer hoses must be purchased separately. For complete detailed installation and operating instructions, see installations instructions (No. M98808) supplied with Thermostatic Mixing Valve. MAINTENANCE A HAND WASH SENSOR OPERATION; Fig. REMOVE PROTECTIVE FILM FROM SENSOR EYE WHEN INSTALLATION IS COMPLETE. When the Sensor detects a user, the water immediately starts to flow. Water flow will stop. seconds after user is out of sensor range. This Comfort delay allows the user to comfortably move their hands without the water turning off. As a precaution, a Safety Timer will turn off the water, after the sensor has been blocked for 9 seconds. The water will stay off until the blockage is removed from the detection zone. The Comfort and Safety time settings can be adjusted using the Optional Remote Control (0XRCT). Fig. () INLINE FILTER Fig. Installation Instructions Fig. SELECTRONIC Thermostatic Mixing Valve 0XTMV HOT Specifications Installation Adjust Temperature Service Replacement Parts TE TO INSTALLER: Please give this manual to the customer after installation. please call -800--90 (In Canada: -800-87-09) No. M98808 DETECTION ZONE PROTECTIVE FILM TEMPERED WATER SUPPLY IMPORTANT: Do not use sealent on threads HOT SUPPLY TEE FITTING COLD Optional Mixing Valve (Sold Separately) COLD WATER COLD SUPPLY M97 Rev.. (/7)
B REPLACE BATTERY; Fig., 7. Remove COVER SCREW () and lift COVER () off.. Disconnect SENSOR CABLES () and (7) from the BATTERY and SOLEID VALVE. (Fig. 7). Push BATTERY (7) forward and Pull it out. (Fig. ). Replace the new battery with the same placement. (Insert terminal side first) C REPLACE SENSOR; Fig.,, 7 7. Remove COVER SCREW () and lift COVER () off.. Disconnect SENSOR CABLES () and (7) from the BATTERY and SOLEID VALVE. (Fig. 7) 9. Remove the AERATOR RETAINER SCREW () and BODY FIXATION SCREW (). (Do not remove SPOUT TUBE ). FOR ABOVE DECK MIXING FAUCETS Remove FIXATION SCREW (). Pull the HANDLE ASSEMBLY () to remove the shaft from the MANIFOLD (). Fig.. Lift BODY () off of MANIFOLD ().. Remove SENSOR (9) by carefully pushing on the face of the sensor. Once removed, peal the SENSOR ADHESIVE off of the BODY and clean the remaining residue. 7. To install the new SENSOR, peal the paper liner from the double sided tape and carefully place the SENSOR in its original position so that the WIRES point upward. Press and hold the sensor for - 0 seconds to ensure it sticks properly. Note: To prevent damage to the wires, verify that they are tucked inside the hooks which are located on both sides of the sensor. 8. FOR ABOVE DECK MIXING FAUCETS Slide SPOUT () over the MANIFOLD () being careful to avoid interference between the SPOUT TUBE () and SENSOR (9). Tighten the BODY FIXATION SCREW (). Insert HANDLE ASSEMBLY () into the MANIFOLD () and secure it with FIXATION SCREW (). Move the SPOUT TUBE () and AERATOR RETAINER () into position and tighten the AERATOR RETAINING SCREW () to secure the assembly. Reconnect SENSOR CABLES ( and 7) to the BATTERY and SOLEID VALVE. Install COVER () and secure it with COVER SCREW (). Tuck extra lengths of wire in the empty space located above FIXATION SCREW () Fig. 0 9. Slide SPOUT () over the MANIFOLD () being careful to avoid interference between the SPOUT TUBE () and SENSOR (9). Tighten the BODY FIXATION SCREW (). Move the SPOUT TUBE () and AERATOR RETAINER () into position and tighten the AERATOR RETAINING SCREW () to secure the assembly. Reconnect SENSOR CABLES ( and 7) to the BATTERY and SOLEID VALVE. Install COVER () and secure it with COVER SCREW (). Tuck extra lengths of wire in the empty space located above FIXATION SCREW () Fig. 7 7 7 M97 Rev.. (/7)
D CHANGE SENSOR RANGE; Fig.,, 7. Remove the COVER SCREW ().. Remove the COVER ().. Disconnect the BLACK POWER SUPPLY CONNECTOR (7) and reconnect. Fig. 7.. While the SENSOR CONTROL LED (9) is blinking slowly, place your hand - in. (.-0.8mm) in front of the sensor.. When the LED stops blinking and stays ON, move your hand to the desired position and hold in place until the LED begins to blink again.. Once the SENSOR CONTROL LED (9) begins to blink again, remove your hand from the detection zone. When the flashing stops, the detection distance is set. 7. Reassemble the COVER () and secure it with COVER SCREW (). E ADJUST HOT LIMIT STOP; Fig., Fig. To reduce the amount of hot water that can mix with cold, the installer can adjust hot limit stop (Four different settings).. Rotate LEVER HANDLE () counter-clockwise to its stop position (00% cold).. Remove LEVER SCREW () and pull off the LEVER HANDLE ().. Pull out LIMIT STOP () from the VALVE STEM ().. Rotate LIMIT STOP () between the shaded area and insert back onto VALVE STEM ().. Each notch on the LIMIT STOP () will reduce the amount of hot water by approximately %. For example, the nd notch will have 97% of maximum temp, the rd notch will have 9% and the fourth will be 9%.. Replace LEVER HANDLE (), LEVER HANDLE SCREW () and tighten. F ADJUST OR REPLACE MAXIMUM OUTLET TEMPERATURE; Fig.. With the COVER off, the installer can reduce the maximum mixed water temperature by turning the THERMO VALVE () clockwise with a screwdriver.. Remove SCREW () and unthread THERMO VALVE (). Replace with new THERMO VALVE (). WARNING Do not turn the THERMO VALVE () More than turn. The maximum mixed water temperature can not be increased due to ASSE 070 requirements. Fig. G GENERAL CLEANING. Only use a damp, soft cloth to clean the spout and the sensor.. For tougher dirt, use a soft cloth with diluted dish washing detergent. Wipe the area using a wet cloth and dry using a soft cloth. CAUTION Do not scratch the sensor when cleaning. Avoid using any abrasives or harsh detergents or chemicals. Fig. 8 M97 Rev.. (/7)
TROUBLESHOOTING FLOW CHARTS UNIT DOES T FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? REPEATED DOUBLE FLASH ON SENSOR? RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR SECONDS? REPLACE SOLEID OPEN EXTERNAL SUPPLY STOPS. CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR. WATER IS CONTINUOUSLY RUNNING RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR SECONDS? CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR. REPLACE SOLEID LOW FLOW ISSUES ARE EXTERNAL SUPPLY STOPS FULLY OPEN? FULLY OPEN EXTERNAL SUPPLY STOPS BY TURNING COUNTER CLOCKWISE. CHECK FOR BLOCKAGE INSPECT FILTER ASSEMBLY, AERATOR AND SOLEID VALVE. REMOVE, CLEAN AND INSERT BACK TO ORIGINAL POSITION. HOT LINE FOR HELP For toll-free information and answers to your questions, call: (8) CRT-TEAM / (8) 78-8 Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST Saturday 0:00 a.m. to :00 p.m. EST IN MEXICO 0-800-89-00 IN CANADA -800-87-09 (TORONTO -90-0-09) Weekdays 8:00 a.m. to 7:00 p.m. EST Product names listed herein are trademarks of AS America, Inc. 07 To learn more about American Standard Selectronic Products visit our website at: www.americanstandard-us.com or e-mail us at: CRTTEAM@lixilamericas.com 9 M97 Rev.. (/7)