More time on the road. Illustrated Parts List

More time on the road Illustrated Parts List RTO-09MLL November 008

Contents How To Use The Illustrated Parts List... AUXILIARY DRIVE GEAR... CASE (AUX)... CASE (FRONT)... COMBINATION CYLINDER...8 COUNTERSHAFT & BRGS(AUX)...9 COUNTERSHAFT ASSY...0 FILTER REGULATOR... H & C W/A-000 VALVE... INPUT SHAFT & DRIVE GEAR... INTEGRAL OIL PUMP... ISOLATORS... KITS & ASSEMBLIES... LEVERS/HOUSINGS...9 MAINSHAFT & SYNCHRO(AUX)... MAINSHAFT ASSY... MISCELLANEOUS... OIL COOLER... REVERSE IDLER... ROADRANGER VALVE... SHIFT BAR HOUSING...9 SLAVE VALVE - A-000... Appendix...

How To Use The Illustrated Parts List The information contained in this document is subject to frequent updates. Therefore, for the latest information available, please visit the interactive Electronic Parts Catalog at www.roadranger.com/epc. Model Designation or Nomenclature For information regarding Model Designation and Nomenclature, visit www.roadranger.com. Kits and Assemblies (K/A's) Kits and Assemblies contain groups of individual or assembled parts developed for optimal replacement or repair of a service problem. Kits and Assemblies are shown with applicable parts groupings in the parts listings. Identifying Kits and Assemblies A- Part numbers beginning with the letter 'A' are pre-assembled Production Assemblies K- Part numbers beginning with the letter 'K' are kits that are not assembled S- Part numbers beginning with the letter 'S' are pre-assembled Service Assemblies Note: Some Production Assemblies do not begin with a letter prefix (Midrange only). Illustrations Illustrations show parts in assembly groups. Item numbers on illustrations correspond with parts listings on pages adjacent to the illustration. Notes are included on illustrations where additional information is needed. Parts Listing Parts listings are defined by parts groupings and are broken down by service assemblies. Parts listings identify a part for servicing with the following categories Item Number - corresponding with numbers on illlustrations for part identification. Current Part - indentifies part as it is available for service. Description - specifies part name or description. Replaced Part - quantity quantity required for assembly. Quantity - defines unique characteristics or requirements. Notes - indicates Kits or Assemblies that contain a particular part. Kits/Assy's Where Used

Group: AUXILIARY DRIVE GEAR 080-/9 Aux DG AUXILIARY DRIVE GEAR SNAP RING K-8,K-88,K-8 0 SNAP RING RETAINER 8 SNAP RING K-8 0- BEARING 0,0 K-8,K-88 BOX 8 BEARING RETAINER X-8- CAPSCREW X 8 /8"-X" 9 AUXILIARY DRIVE GEAR

Group: CASE (AUX) 0 OEM supplied adjustable speedometer sensor OEM supplied non-adjustable speedometer sensor 8 8 9 9 0 CASE (AUX) 00A--9 Aux Case X-8L- CAPSCREW /8"-X-/" S- REAR BRG COVER ASSY,00,S - MECHANICAL AND MAGNETIC,S - GASKET K-0,K-0,K-,S- 0 PLUG-MAGNETIC S-,S- 09 SENSOR SEAL S- 0 PLUG-MECHANICAL S-,S- -O- RING S-,S- 8 99 BUSHING S- 9 X-8L-0 CAPSCREW /8"-X-/" 9 X-8L- CAPSCREW /8"-X" 0 GASKET K-0,K-0,S- REAR HOUSING K-80 SHIM KIT K - 0 K-8,K-88,S- 098 GASKET 0 K-0,K-0,S- 00 COVER S- 08 LIFTING EYE S- X-8L-0 CAPSCREW 8 /8"-X-/" K- OIL SEAL W/SLINGER 909 080 0808 "FOR MECHANICAL COVER" K-8,K-88 8 090 SEAL A-99 9 A-99 SPACER-SLINGER ASSY 9,099 0 K- OIL SEAL TOOL KIT

Group: CASE (FRONT) 8 9 0 8 Latest Design 0 * 8 9 9 8 0 8 * 9 9 000--9 Iron/Alum Hsg * Bushing quantity requirements: # Housing Upper bore use #8 / Lower bore use #8. # Housing Upper bore use #8 and #8 / Lower bore use #8. Note: Some part requirements are specific to # or # Aluminum or Iron Clutch Housings and Push or Pull type Clutch. CASE (FRONT) S-09 CASE ASSY 8,08 S-0 CASE ASSY 00 FOR USE W/INTEGRAL PUMP X--00 PIPE PLUG X 00 X--0 PIPE PLUG X 0,X 0 /" MAGNETIC 00 GASKET 080 K-0 0809 PTO COVER 9,00 X-8- CAPSCREW X 8 8 /"-X/8" 08 GASKET 08 K-0 8 A- CLUTCH HOUSING ASSY A - 00 # PUSH-PULL IRON 8 A- CLUTCH HOUSING ASSY A -,A - # PUSH-PULL IRON 8 A- CLUTCH HOUSING ASSY A -,A - # PUSH-PULL ALUM. 8 A-99 CLUTCH HOUSING ASSY 00 # PULL ALUM.(SPECIAL-LIGHTER WEIGHT) 8 A-0 CLUTCH HOUSING ASSY A -,A - 0,A - # PUSH-PULL ALUM. 0,A - 0,A - 0 9 X-8L-09 CAPSCREW /"-8X/" QUANTITY DEPENDENT ON DESIGN 0 0 HAND HOLE COVER # PUSH 0 0 HAND HOLE COVER # PULL 0 00 HAND HOLE COVER # PULL 0 0 HAND HOLE COVER # PUSH 008 STUD 9 X-0-00 WASHER X 000,X0 000. X.0,X0 00 X--00 NUT X 000 /8"-8 00 FRONT BEARING COVER " PULL K-8 X-8L-0 CAPSCREW /8"-X-/" 09 FRONT BEARING COVER " PUSH GASKET K-0 8 8 BUSHING FOR # HOUSING UPPER A-,A-,A-

,A-99,A- 0,K-8 8 8 BUSHING FOR # HOUSING UPPER A-,A-,A-,A-99,A- 0,K-8 8 8 BUSHING FOR # HOUSING UPPER A-,A-,A-,A-0 9 8 BUSHING FOR # AND # HOUSING LOWER A-,A-,A-,A-0 0 X-8C-8 CAPSCREW X 8 8,X 8L 8 /- X -/ - FOR IRON HOUSING 0 X-8C-8 CAPSCREW,X 8 809,X 8L 809,X 8L 8 /- X -/ - FOR IRON HOUSING 0 X-8C-8 CAPSCREW,X 8 809,X 8L 809,X 8L 8 /- X -/ - FOR ALUMINUM HOUSING 00 PLUG 0 -/" MAGNETIC, O-RING S-09,S-0 INCLUDED X-8-8 CAPSCREW /8"-X/" PTO COVER 0 009 GASKET 8 K-0 MAGNET S-09,S-0 8 88 PIN 9 X--00 NUT X 000 /8"-8 0 X-0-00 WASHER X 000,X0 000. X.0,X0 00 STUD,9 /8" X -/" 0 PLUG X-8-00 CAPSCREW /8"-X-/" 8 08 SPACER 9 X--80 PIPE PLUG X 800 /"

Group: COMBINATION CYLINDER 0 8 9 8 9 0 0--9 CMB CYL COMBINATION CYLINDER A-9 YOKE ASSY RANGE A-0 YOKE ASSY REDUCTION 0 CYLINDER K-8 GASKET K-0,K-0,K- 8,K-8 -O- RING K-8,K-8 PISTON K-8 -O- RING K-8,K-8 8 -O- RING K-8,K-8 9 X--00 NUT /8"-8 0 -O- RING K-8,K-8 K- PISTON KIT,00 0 -O- RING K-8,K-8 X--80 NUT /"-0 9 CYLINDER COVER 08 -O- RING K-,K-8,K-8 X-8L- CAPSCREW X 8 /8"-X-/" 99 INSERT VALVE 0 8 -O- RING 9 9 PLUG 0 GASKET K-0,K-0,K-,K-8,K-8 8

Group: COUNTERSHAFT & BRGS(AUX) 0--9 AUXCS COUNTERSHAFT & BRGS(AUX) A-8 WELDED A -,A - 8 D/G 098 - C/S 09 COUNTERSHAFT ASSY 00- BEARING,00 K-8,K-88 BOX SPACER 9

Group: COUNTERSHAFT ASSY 9 8 0 0-/9 CS/RT COUNTERSHAFT ASSY SNAP RING K-8,K-88,K-8 BEARING K-8,K-88 K-9 CNTRSHFT W/REV & LO 0 X--E KEY ROLL PIN 080 KEY 9 0 ST GEAR-CNTRSHFT 99 8 ND GEAR-CNTRSHFT 9 9 OD GEAR-CNTRSHFT 99,0 0 9 PTO GEAR - LOWER 0 080 PTO GEAR - UPPER 0 DRIVE GEAR-CNTRSHFT 08,009 998 SNAP RING 099 BEARING 0 098 K-8,K-88 00 RETAINER 98 ROLL PIN NO LONGER REQUIRED X--00 CAPSCREW /8"-8X-/" 0

Group: FILTER REGULATOR NSS -O- Ring/Element Kit 00--9 AFR NSS - Not Sold Separately FILTER REGULATOR K-0 FILTER REG KIT A - K-98 -O- RING/ELEMENT KIT FOR FILTER REGULATOR X-8C- CAPSCREW X 8S /"-0X-/"

Group: H & C W/A-000 VALVE 9 H P From RRV 8 0 0 Combination Cylinder From RRV 8 S 9 L 9 S 0 00H--9 A-000 HC H & C W/A-000 VALVE A-000 SLAVE VALVE ASSY 080 98 GASKET K-0 9 -O- RING 0 K-99 K-99 SLEEVE KIT,90, FOR SLAVE VALVES 8 SPRING 9 090 PIN 99 8 ELBOW /8" 8 X-8C- CAPSCREW /"-0X-/" 9 09 HOSE ASSY " 0 8 HOSE ASSY " K-0 FILTER REG KIT A - X--08 PIPE PLUG /8" NPT X-8L-00 CAPSCREW /8"-X" HOSE CLAMP STRAP BRACKET 8 HOSE CLAMP 8 X-8L-0 CAPSCREW /8"-X-/" 9 08 BRANCH TEE /8" 0 880 ELBOW /8" -O- RING A-000,K-9,K- 0,K-8

Group: INPUT SHAFT & DRIVE GEAR 9 8 * * 00-/9 IS * For Shipping Only -- Do Not Replace INPUT SHAFT & DRIVE GEAR 9 SHIPPING SEAL NOT SOLD FOR SERVICE 980 SNAP RING K-8,K-8,K-88 80 BEARING K-8 SPACER 0 SNAP RING K-8,K-8,K- 88,K-8 9 MAIN DRIVE GEAR 99 8 S-9 INPUT SHAFT " PULL K-8,K-88 8 S-0 INPUT SHAFT " PUSH 9 BUSHING K-8,S-9,S-0

Group: INTEGRAL OIL PUMP Indicates Part Of Item 999 0 0 0 9 0 9 8 8 00-/9 Oil Pump Latest Design INTEGRAL OIL PUMP X-8C-09 CAPSCREW /"-0X/8" - USE WITH 00 COVER X-8C-0 CAPSCREW /"-0X/8" - USE WITH 0 COVER K-0 COVER & SCREW KIT 0,00 0 GASKET K-0,K-0 08 PLUG -O- RING K-8,K-8 X-8-8 SCREW X 8 /"-0X-/" 08 WASHER K- 8 08 DOWEL PIN 9 00 RETAINER 00 S-0 0 K- OIL PUMP KIT 089,098,0,09,0 A - 9,A - 08 CRESCENT RING ROLL PIN ROLL PIN K- OIL PUMP KIT 089,098,0,09,0 A - 9,A - X--00 STEEL BALL /" 0 PLUG 0 -O- RING 8 0 SUCTION TUBE 08 O-RING INCLUDED ON SUCTION K- TUBE 9 008 DRIVE SHAFT 0 009 KEY 8 SNAP RING 0 DRIVE GEAR 08 GASKET 08 K-0 S-0 CASE ASSY 00 FOR USE W/INTEGRAL PUMP MAGNET S-09,S-0 00 ELEMENT

K- OIL PUMP KIT 089,098,0,09,0 A - 9,A - 999 K- OIL PUMP KIT 089,098,0,09,0 A - 9,A -

Group: ISOLATORS New Design 9 New Design 0 00--9 Isolator ISOLATORS Indicates Part Of Item 0 9 -E- RING K- PIN REPLACEMENT KIT BUSHING K-00,K-8,K- 9,K-98,K-99,S- 9,S-0,S-9 S-9 ISOLATOR ASSY LEVER STRAIGHT 8." STUB LEVER LOW TOWER K-8,S- STUB LEVER HIGH TOWER K-9,S-9,S-0 08 STUB LEVER MID TOWER K-98 9 90 DEG LEVER STRAIGHT " 0 K-99 ISOLATOR BUSHING KIT, X-8-0 SCREW X-9-0 NUT

KITS & ASSEMBLIES K- SHIFT LEVER HSG 0,,898 LOW TOWER,090,A - K-98 -O- RING/ELEMENT KIT FOR FILTER REGULATOR K-9 MASTER VALVE REPAIR FOR A-0 VALVE KIT K-9 REPAIR KIT-SLAVE FOR A-000 VALVE VALVE K-9 COOLER INSTLN KIT K-99 SLEEVE KIT,90, FOR SLAVE VALVES K-00 PIN & BUSHING KIT K-0 MASTER VALVE REPAIR FOR A- VALVE KIT K-0 GASKET KIT K-8,K-88 K-0 GASKET KIT FOR AUXILIARY SECTION K-0 FILTER REG KIT A - K- OIL SEAL W/SLINGER 909 080 0808 "FOR MECHANICAL COVER" K-8,K-88 K-9 AIR SYSTEMS TOOL KIT K- PISTON KIT 00 K-8 LEVER REPLACEMENT LOW TOWER KIT K-9 LEVER REPLACEMENT HIGH TOWER KIT K-8 CLUTCH INSTALLATION KIT FOR USE WITH S-9 INPUT SHAFT ASSY AND 80 INPUT SHAFT BEARING K-80 SHIM KIT K - 0 K-8,K-88,S- K-8 -O- RING KIT K-8,K-88 K-8 BASIC REBUILD KIT K-88 BASIC OVERHAUL KIT K-8 SMALL PARTS KIT K-8 CYLINDER KIT K-88 KEY & WASHER KIT CONTAINS -SIDED KEY K-9 COUNTERSHAFT REPL KIT K-9 SHIFT LEVER HSG KIT,,000,090,K - 0 K - 9 0 K-9 SHIFT LEVER HSG KIT 0,090,A - 00 K-98 LEVER REPLACEMENT KIT K-9 MASTER VALVE REPAIR KIT K-9 MASTER VALVE REPAIR KIT K-09 IDLER SHAFT REPL KIT 0,098,0 K- OIL PUMP KIT 089,098,0,09,0 A - 9,A - K-99 ISOLATOR BUSHING KIT, K- PIN REPLACEMENT KIT K-9 SYNCHRONIZER KIT K - HIGH TOWER MID TOWER MID TOWER FOR A-9 VALVE FOR A- VALVE K-9 SYNCHRONIZER REPLACEMENT KIT K - 8 SLIDING CLUTCH INCLUDED IN KIT K- OIL SEAL TOOL KIT S-0 OIL FILTER 8 S- SHIFT BAR HSG 890,0,0,0,08,0 HOUSING ONLY (STD) S- CAP ASSY 08,08 S-9 INPUT SHAFT 0 0 " PULL - USE W/FBC 00 K-8,K-88 S-0 INPUT SHAFT " PUSH - USE W/FBC 09 S-9 ISOLATOR ASSY S-9 SHIFT LEVER HSG ASSY LOW TOWER S-0 SHIFT LEVER HSG ASSY S - 0 HIGH TOWER S- REAR BRG COVER ASSY,00,S -,S - MECHANICAL AND MAGNETIC

S-0 SHIFT BAR HSG 09 HOUSING ONLY (F) S-0 SHIFT BAR HSG ASSY 0 COMPLETE (STD) S-08 SHIFT BAR HSG ASSY 09 COMPLETE (F) S-09 CASE ASSY 8,08 S-0 CASE ASSY 00 FOR USE W/INTEGRAL PUMP S- RANGE SECTION ASSY S-9 SHIFT LEVER HSG ASSY S - 99 MID TOWER S-0 ROADRANGER VALVE ASSY A - 8 RTO - W/SHIFT DIAGRAM MEDALLION S-88 MAINSHAFT ASSY 00,09 8

Group: LEVERS/HOUSINGS 8 9 K-8 - Low K-98 - Mid K-9 - High 8 0 S- - Low S-9 - Mid S-9 - High 8 00-9-9 S-9 - Low S-9 - Mid S-0 - High LEVERS/HOUSINGS K- O-RING & WASHER KIT 0 899 PIN K-,K-9,S- X-8C-0 CAPSCREW /8"-X-/" S- X--00 NUT /8"--N.F.PLAIN X--00 LOCKWASHER /8" 9 STUD K- SHIFT LEVER HSG 0,,898 LOW TOWER,090,A - 8 09 GASKET 0 K-,K-0,K- 8,K-9,K- 9,K-9,K-98,S- 9,S-,S-9,S- 9,S-0,S-9 9 K-9 SHIFT LEVER HSG KIT 0,090,A - MID TOWER 00 000 PIN K-9,S-9,S-0 PIN /8" - USED W/ ONLY K-9 SHIFT LEVER HSG KIT,,000 HIGH TOWER,090,K - 0 K - 9 0 BOOT K-,K-9,K- 9,S-9,S-,S- 0 X--00 NUT /8"--N.F.PLAIN X--00 LOCKWASHER /8" 0 00 GEAR SHIFT LEVER STRAIGHT - LOW -/" 0 88 GEAR SHIFT LEVER STRAIGHT - HIGH " 8 RETAINER K-,K-9,K- 9,S-9,S-,S- 0 9

SPRING K-,K-9,K- 9,S-9,S-,S- 0 K-8 LEVER REPLACEMENT LOW TOWER KIT K-9 LEVER REPLACEMENT HIGH TOWER KIT K-98 LEVER REPLACEMENT MID TOWER KIT S-9 SHIFT TOWER ASSY HIGH TOWER S- SHIFT TOWER ASSY LOW TOWER S-9 SHIFT TOWER ASSY MID TOWER S-9 SHIFT LEVER HSG ASSY LOW TOWER S-0 SHIFT LEVER HSG ASSY S - 0 HIGH TOWER S-9 SHIFT LEVER HSG ASSY S - 99 MID TOWER 0

Group: MAINSHAFT & SYNCHRO(AUX) 9 8 0 0 9 0 8 Universal Joint Yoke 08--9 Aux MS MAINSHAFT & SYNCHRO(AUX) 89 SPRING K-8,K-88,K- 8,K-9,K-9 A- SYNCHRONIZER ASSY 09 09 A - HI RANGE K-9,K-9 9 0 SLIDING CLUTCH K-9 A- SYNCHRONIZER A - 9 A - 8 LO RANGE K-9,K-9 ASSEMBLY NUT K-8 DOWEL PIN K-8 WASHER K-8 8 0 WASHER K-8 9 08 REDUCTION GEAR 0 0 BUSHING A- A- MAINSHAFT ASSY PIN K-8 0 SLIDING CLUTCH MAINSHAFT WASHER K-8 00 DEEP REDUCTION GEAR 8 WASHER K-8 8 09 ROTOR 9 9 NUT S- 0 -BOX BEARING K-8,K-88

Group: MAINSHAFT ASSY 8 0 9 8 0--9 MS w/ OD -Sided Key Design MAINSHAFT ASSY 0 -SIDED KEY 00890 K-8,K-88 K-88 KEY & WASHER KIT CONTAINS -SIDED KEY S-88 MAINSHAFT ASSY 00,09 0 ROLL PIN S-88 0 SNAP RING K-8,K-8,K- 88,K-8 0 REVERSE GEAR- MAINSHAFT 9 SPACER K-8 008 WASHER.9-WHITE OPTIONAL 008-008 OR K-8,K-88 0080 USE ANY WASHERS. USE WITH -SIDED KEY 008 WASHER.-GREEN OPTIONAL 008-008 OR K-8,K-88 0080 USE ANY WASHERS. USE WITH -SIDED KEY 008 WASHER.9-ORANGE OPTIONAL 008-008 OR K-8,K-88 0080 USE ANY WASHERS. USE WITH -SIDED KEY 008 WASHER.-PURPLE OPTIONAL 008-008 OR 0080 USE ANY WASHERS. USE WITH -SIDED KEY 008 WASHER.9-YELLOW OPTIONAL 008-008 OR 0080 USE ANY WASHERS. USE WITH -SIDED KEY 008 WASHER.-BLACK OPTIONAL 008-008 OR 0080 USE ANY WASHERS. USE WITH -SIDED KEY 0080 WASHER.-BLUE OPTIONAL 008-008 OR 0080 USE ANY WASHERS. USE WITH -SIDED KEY K-8,K-88

8 8 SLIDING CLUTCH 9 08 LO GEAR-MAINSHAFT 0 0 ST GEAR-MAINSHAFT 98 09 ND GEAR-MAINSHAFT 09 09 OD GEAR-MAINSHAFT 000 098 WASHER K-8,K-88 0 SLIDING CLUTCH 0 K-88 9 SPACER K-8 00 WASHER 09 K-8,K-88

MISCELLANEOUS 0 SHIFT DIAGRAM LABEL 0 SILICONE LUBE 8 OZ (.9 CC)-FLEET SIZE 0 ADHESIVE SEALANT 0. CC (SINGLE APPLICATION SIZE) 0 SEALANT CC (SINGLE APPLICATION SIZE) K-88 0 SILICONE LUBE CC (SINGLE APPLICATION SIZE) K-8,K-9,K- 8,K-8,K-98

Group: OIL COOLER Flow 8 9 Oil Return 0 Oil Pump Outlet * * Outlet * Fuller * Inlet * Return Outlet 0-/9 Cooler *Adding Oil Filter and parts as shown is optional. Return / Outlet Location OIL COOLER 80 OIL COOLER K-9 9 HOSE FEET K-9 X-8- CAPSCREW /"-X-/" X--0 LOCKWASHER /" 8 BRACKET K-9 99 CONNECTOR K-9,S-0 9 SWIVEL K-9 8 X-0-0 WASHER /" 9 809 PLUG-RUBBER MOUNT K-9 0 90 STRAP 8 K-9 9 CLAMP K-9 80 NUT K-9 9 ELBOW K-9 S-0 OIL FILTER 8 FILTER ELEMENT S-0

Group: REVERSE IDLER Latest Design 0 8 9 9 Old Design 8--9 RI Old Design REVERSE IDLER X--008 NUT /8"-8 8 WASHER 098 WASHER 8 K-09,S-09,S-0 8 BEARING 000 K-8,K-88 REVERSE IDLER GEAR 0 RETAINING RING K-09 K-09 IDLER SHAFT REPL KIT 0,098,0 8 0 PLUG 9 8 NO LONGER AVAILABLE 0 X--008 CAPSCREW /8"-8X-/ 0 RETAINING RING K-09 0 IDLER SHAFT K-09

Group: ROADRANGER VALVE Old Design 999 H/L P S SP * * * * See: Appendix / Airline Tubing * P * 0 S * 0 SP * 0 Combination Cylinder 00D--9 H/L To Slave Valve *For Connector and Elbow Assy component information see Appendix. ROADRANGER VALVE 00 MEDALLION, LOGO (OLD DESIGN) FULLER LOGO ONLY 9 LOGO MEDALLION 09, 000 (OLD DESGIN) FULLER LOGO (LEFT OF DRIVER) 800 MEDALLION, LOGO (LATEST DESIGN) FULLER LOGO A-9,A- ONLY 80 SHIFT DIAGRAM RTO S-0 MEDALLION K-9 MASTER VALVE REPAIR FOR A-0 VALVE KIT K-0 MASTER VALVE REPAIR FOR A- VALVE KIT K-9 MASTER VALVE REPAIR FOR A-9 VALVE KIT K-9 MASTER VALVE REPAIR FOR A- VALVE KIT 09 LEVER A-9,A- 0 COVER A-9,A- X-8- SCREW X 8 0 8-X/8" X-9-80 NUT /"- 800 CONNECTOR ASSY 80 /8"TUBE-/"NPTF 800 CONNECTOR ASSY 80 /"TUBE-/"NPTF 800 CONNECTOR ASSY "PUSH-TO-CONNECT" /"TUBE- /"NPTF 0 800 ELBOW ASSY 80 /"TUBE-/8"NPTF 0 800 ELBOW ASSY 80 /8"TUBE-/8"NPTF 0 800 ELBOW ASSY "PUSH-TO-CONNECT" /"TUBE- /8"NPTF 80 UNION ASSY /8" TUBING 80 UNION ASSY /" TUBING K-88

80 UNION ASSY "PUSH-TO-CONNECT" /" TUBING -O- RING CLAMP 800 CONNECTOR ASSY 80 /"TUBE-/8"NPTF 999 A-9 ROADRANGER VALVE A - 0 STANDARD-W/LOGO ASSY 999 A- ROADRANGER VALVE A - (LEFT OF DRIVER)-W/LOGO ASSY 999 S-0 ROADRANGER VALVE ASSY A - 8 RTO - W/SHIFT DIAGRAM MEDALLION 8

Group: SHIFT BAR HOUSING 8 9 0 999 0 9 8 9 8 0 9 9 0--9 X-Bar SHIFT BAR HOUSING S- SHIFT BAR HSG (STD) 890,0,0 HOUSING ONLY (X),0,08,0 0 GASKET 98 K-0,S-0,S-08 00 BREATHER 0 /" NPT X--0 PIPE PLUG /" NPT 000 OIL TROUGH S-0,S-08 0 AIR VALVE SHAFT S-0,S-08 X-8- CAPSCREW /"-0X/" X--0 PIPE PLUG X 0 /8" NPT 9 GASKET S-,S-0,S- 0,S-08 0 PLUG 8 S-,S-0,S- 0,S-08 9 NEUTRAL LIGHT SWITCH 9 SWITCH NORMALLY CLOSED 08 LIFTING EYE 0 S- X-8L-0 CAPSCREW /8"-X-/" X-8L-0 CAPSCREW /8"-X-/" OR USE PCS OF X- 8L-0 WITH PCS OF X-8L-0 899 PIN S-,S-0,S- 0,S-08 8 900 GASKET S-,S-0,S- 0,S-08 9 90 REVERSE LIGHT SWITCH 80 SWITCH NORMALLY OPEN 0 0 PLUG 9 S-,S-0,S- 0,S-08 98 SPRING K-88,K-8,S- 0,S-08 X--800 STEEL BALL /" K-0 ACTUATOR PIN KIT 08 9

0 SHIFT YOKE REVERSE/LO X--00 STEEL BALL /" 8 8 SHIFT BLOCK ST/ND S-0 9 0 LOCKSCREW S-0,S-08 0 INTERLOCK PIN K-8,S-0,S-08 90 SHIFT BLOCK RD/OD (REAR) S-0 00 SHIFT BLOCK 89 RD/OD (FRONT) S-0,S-08 898 YOKE BAR 00 RD/OD S-0 89 SHIFT YOKE ST/ND S-0,S-08 89 YOKE BAR ST/ND S-0 000 SNAP RING K-0,S-0,S-08 0 ACTUATOR S-0,S-08 8 0 SHIFT YOKE 00 RD/OD S-0,S-08 9 89 YOKE BAR REVERSE/LO S-0 0 990 PLUNGER 99 SPRING 988 SPRING LOCKSCREW S-0,S-08 99 RETAINER 99 SNAP RING A-000,K-9 999 S-0 SHIFT BAR HSG ASSY (STD) 0 COMPLETE 0

Group: SLAVE VALVE - A-000 8 00-0-9 A-000 SV Repair Kit SLAVE VALVE - A-000 A-000 SLAVE VALVE ASSY 080 K-9 REPAIR KIT-SLAVE FOR A-000 VALVE VALVE 08 PLUG A-000 08 PISTON A-000 089 CAP A-000 S- CAP ASSY 08,08 8 X-8C- CAPSCREW /"-0X-/"

Appendix Air Line Tubing Choosing nylon tubing for air lines Use the following chart to specify the Eaton Fuller nylon tube appropriate to your vehicle's air system. /" Air Line and Harness Combinations Line Type Line Color Order Part No. Length Supply + Port Red (S) + Black (P) 0 0 ft Splitter + Deep Reduction Blue (SP) + Green (H/L) 0 0 ft Supply + Splitter + Port Red(S)+Blue(SP)+ Black(P) 0 0 ft /" Air Lines Line Type Line Color Order Part No. Length Supply Red (S) 0 0 ft Port Black (P) 0 0 ft Splitter Blue (SP) 0 0 ft Deep Reduction Green (H/L) 0 0 ft Sheathing 800 0 ft /8" Air Lines Line Type Line Color Order Part No. Length Supply White 8 0 ft Port Black 80 0 ft Sheathing 80000 0 ft 00-/9 AL Chart

Copyright Eaton Corporation and Dana Limited, 008. Eaton and Dana hereby grant their customers, vendors, or distributors permission to freely copy, reproduce and/or distribute this document in printed format. It may be copied only in its entirety without any changes or modifications. THIS INFORMATION IS NOT INTENDED FOR SALE OR RESALE, AND THIS NOTICE MUST REMAIN ON ALL COPIES. For spec ing or service assistance, call -800-8-HELP () hours a day, days a week (Mexico 00-800-8-), for more time on the road. Or visit our web site at www.roadranger.com. 008 Eaton Corporation All rights reserved. Roadranger: Eaton, Dana and other trusted partners providing the best products and services in the industry, ensuring more time on the road. Eaton Corporation Truck Components Operations P.O. Box 0 Kalamazoo, MI 900 U.S.A. www.roadranger.com