R SOUND and PERFORMANCE MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Jenco, Div. of Soler & Palau Ventilation Group, certifies that the models shown herein are licensed to bear the AMCA Seal. The ratings shown are based on test and procedures performed in accordance with AMCA Publication and AMCA Publication and comply with the requirement of the AMCA Certified Ratings Program. L.07 sidewall propeller fans belt drive - exhaust & supply three levels of construction models lc, l & l january 007
model lc - construction level Application Model LCE (exhaust) and LCS (supply) are high capacity belt driven propeller fans rated from,000 to 40,000 cfm to.65" w.g. static pressure. Their primary application is the exhaust or supply of large volumes of air at relatively low static pressures from commercial, light industrial and agricultural buildings such as manufacturing and assembly plants, warehouses, parking garages, gymnasiums, equipment rooms, distribution centers, poultry and greenhouses. Wall mounting provides an easy, economical installation. Belt driven fans provide large volumes of air at low fan speeds and low noise levels and afford quick, easy performance adjustments. All necessary accessories are available to meet any need or specification. When suspended from the ceiling, thus keeping floor spaces open, model LC can be installed to direct large volumes of air downward toward work centers improving employee comfort and productivity. When mounted in portable housings with OSHA guards, Model LC-P can be used as a mancooler and rolled to hot spots to provide needed employee relief from heat or fumes and help increase productivity. Also see Model L with construction levels and for higher static pressure performances and heavier construction designs. (Pages and 4.) Construction/Specification Checklist Belt Drive, Wall Exhaust (or Supply) Propeller shall be provided as follows: CERTIFICATIONS: s shall be AMCA Licensed for air and sound performance. s shall be UL and CUL 705 listed for electrical safety and reliability (Optional). MODEL LC - Level Construction Panel Material (Ga.or inches) Drive & Bearing Supports Propeller Spider Steel Blade Steel Shaft Diameter (in.) PANEL ASSEMBLY: Panels shall be heavy gauge G90 galvanized (optional aluminum) with spun one piece venturi. and bearing plate shall be a minimum of gauge galvanized steel except size 0. Panel end support frame assembly shall be of welded, not bolted, construction with pre-punched mounting holes for easy installation. PROPELLER: Blades shall be die formed galvanized G90 steel of minimum 6 gauge. Blades shall be bolted to an epoxy coated hub which is keyed to the fan shaft. Propeller assembly shall be statically balanced. DRIVES: All sheaves shall be sized to a minimum 50% of driven horsepower, machined cast iron adjustable pitch through horsepower, keyed to both the motor and fan shaft. shaft shall be precision turned, ground and polished steel. Belts shall be non-static oil and heat resistant V-belts. BEARINGS: All bearings shall be self-aligning cast iron pillow block type with re-lube fitting and of the air handling design. Bearing design shall be for a minimum of L-50 00,000 hour average life. MOTORS: Permanently sealed ball bearing type furnished to the specified voltage, phase and enclosure. All motors shall be mounted and factory run tested. Service Factor service factors are utilized in some performance selections shown. This is a safe and common industry practice that provides more performance for the investment. BHP is shown at the maximum catalog performance point. BHP at all other static pressures listed is less than that shown, in most cases substantially less. Because the motors are in the air stream there are no negative effects on motor life. speed motor applications are recommended at or below their nominal BHP levels. If desired, pick the next higher horsepower to eliminate this service factor usage. Refer to the Optisizer Selection Program for actual BHP at any performance point. Optisizer Selection Program Please refer to Jenco s Optisizer Program for fan curve, submittal information and other details of this series and other Jenco products. Contact your representative or factory for a copy. Visit Jenco s website for additional information: www.jencofan.com. Quickship Program Most models and many optional accessories are available on the Quickship Program. This provides rapid delivery of standard products so that tight project deadlines can be met and downtime on replacement work can be held to a minimum. Delivery options includes next day, day and 0 day shipment. See the Quickship Catalog for details. Avg. Weight (lbs.) 0 8 6 6 4 8 56H 85 4 6 0 6 45T 90 0 6 0 6 45T 00 6 6 7 6 45T 05 4 6 7 4 45T 0 48 6 7 4 45T 5 54 4 /4 /6 8T 40 60 4 /4 /6 8T 85 Optional Accessories Wall Housing Wall Collar s Mounting Flanges side Guard Frontside Guard Rainhood Guard Paint Finishes Electrical Accessories All specifications are subject to change without notice unless approved in submittal by Jenco.
model l - construction level DRIVES: All sheaves shall be sized to a minimum 50% of driven horsepower, machined cast iron adjustable pitch (through HP), keyed to both the motor and fan shaft. shaft shall be precision turned, ground and polished steel. Belts shall be non-static oil and heat resistant V-belts. BEARINGS: All bearings shall be self-aligning cast iron pillow block type with re-lube fitting and of the air handling design. Bearing design shall be for a minimum of L-50 00,000 hour average life. Applications: Models LE (exhaust) and LS (supply) are high capacity wall mounted belt driven propeller fans rated from 5000 to 47,000 CFM and to.0" w.g. static pressure. Their primary application is the exhaust of large volumes of ventilation air from commercial and light industrial buildings such as manufacturing and assembly plants, warehouses, parking garages, gymnasiums, equipment rooms, distribution centers and OEM applications. Wall mounting provides an easy and economical installation. All necessary accessories are available. Belt driven fans provide large volumes of air at low fan speed and low noise levels and afford quick, easy performance adjustments. See Model L - Construction level for higher static pressures and heavier construction designs or models LC for your lighter duty ventilation requirements (see pages and 4). Construction/Specification Checklist Belt Drive, Wall Exhaust (or Supply) Propeller shall be provided as follows: CERTIFICATIONS: s shall be AMCA Licensed for air and sound performance. s shall be UL and CUL 705 listed for electrical safety and reliability (Optional). PANEL ASSEMBLY: Panels shall be heavy gauge G90 galvanized (optional aluminum) with spun one piece venturi. and bearing plate shall be a minimum of 0 gauge G90 galvanized steel. Panel end support frame assembly shall be of welded, not bolted, construction with prepunched mounting holes for easy installation. PROPELLER: Propellers shall be six-bladed, die-formed, minimum 6 gauge, G90 galvanized steel bolted to a welded, structural steel hub plate and keyed to the fan shaft. Blades shall incorporate multiple laminations for horsepower motors and larger. Propeller assembly shall be statically balanced. MODEL L - Level Construction Panel Drive Material (Ga.or inches th.) & Bearing Supports Spider Propeller Blade Galv Alum Steel Steel Alum MOTORS: Permanently sealed ball bearing type furnished to the specified voltage, phase and enclosure. All motors shall be mounted and factory run tested. Service Factor service factors are utilized in some performance selections shown. This is a safe and common industry practice that provides more performance for the investment. BHP is shown at the maximum catalog performance point. BHP at all other static pressures listed is less than that shown, in most cases substantially less. Because the motors are in the air stream there are no negative effects on motor life. Explosion proof and speed motor applications are recommended at or below their nominal BHP levels. If desired, pick the next higher horsepower to eliminate this service factor usage. Refer to the Optisizer Selection Program for actual BHP at any performance point. Quickship Program Most models and many optional accessories are available on the Quickship Program. This provides rapid delivery of standard products so that tight project deadlines can be met and downtime on replacement work can be held to a minimum. Delivery options includes:, 5 and 0 day shipments. Optisizer Selection Program Please refer to Jenco Optisizer Program for fan curve, submittal information and other details of this series and other Jenco products. Contact your representative or factory for a copy. Log onto Jenco's web site for additional information at: www.jencofan.com. Optional Accessories Wall Housing Wall Collar s Mounting Flanges side Guard Frontside Guard Rainhood Guard Paint Finishes Electrical Accessories Shaft Diameter (in.) Avg. Weight (lbs.) 4 8 0 0 /4 /4 6.080 8T 80 0 6 0 0 /4 /4 6.080 8T 80 6 6 0 0 /4 /4 6.080 /6 84T 5 4 6 0 0 /4 /8 6.080 /6 84T 5 48 6 0 0 /4 /8 6.080 /6 84T 00 54 4 0 0 /4 /8 6.080 /6 84T 400 60 4 0 0 /4 /8 6.080 /6 84T 490 All specifications are subject to change without notice unless approved in submittal by Jenco.
model l - construction level DRIVES: All sheaves shall be sized to a minimum 50% of drive horsepower, machined cast iron adjustable pitch through horsepower, keyed to both the motor and fan shaft. shaft shall be precision turned, ground and polished steel. Belts shall be non-static oil and heat resistant V-belts. BEARINGS: All bearing shall be self-aligning cast iron pillow block type with re-lube fitting and of the air handling style. Bearing design shall be for a minimum of L-50 00,000 hour average life. MOTORS: Permanently sealed ball bearing type furnished to the specified voltage, phase and enclosure. All motors shall be mounted and factory run tested. Applications: Models LE (exhaust) and LS (supply) are high capacity wall mounted belt driven propeller fans rated from 5,000 to 85,000 and to.0" w.g. static pressure. Their primary application is the exhaust of large volumes of air at relatively moderate static pressure from commercial, industrial and agricultural buildings such as manufacturing and assembly plants, warehouses, founderies, mills, boiler rooms and equipment rooms. Wall mounting provides an easy and economical installation. Belt driven fans provide large volumes of air at low fan speed and low noise levels and afford quick, easy performance adjustments. All required accessories are available with Model L. See Models LC and L - level construction, for lower static pressures and lighter duty requirements which are generally more economical. (Pages and ) Construction/Specification Checklist Belt Drive, Wall Exhaust (or Supply) Propeller shall be provided as follows: CERTIFICATIONS: s shall be AMCA Licensed for air and sound performance. s shall be UL and CUL 705 listed for electrical safety and reliability (optional). PANEL ASSEMBLY: Panels shall be heavy gauge G-90 galvanized (optional aluminum) with spun one piece venturi. and bearing plate shall be a minimum of 0 gauge G90 galvanized steel structurally secured to minimum.5 inch schedule 40 galvanized steel pipe by means of gauge galvanized steel pipe brackets. Panel end support frame assembly shall be of welded, not bolted, construction with pre-punched mounting holes for easy installation. PROPELLER: Propellers shall be six-bladed, die-formed, minimum 6 gauge, G90 galvanized steel with double 6 gauge laminations bolted to a welded, structural steel hub plate and keyed to the fan shaft. shaft shall be precision turned, ground and polished steel. Props shall be statically balanced. Service Factor service factors are used in some performance selections shown. This is a safe and common industry practice that provides more performance for the investment. BHP is at the maximum catalog performance point. BHP at all other static pressures listed is less than that shown, in most cases substantially less. Because the motors are in the air stream there are no negative effects on motor life. Explosion proof and speed motor applications are recommended at or below their nominal BHP levels. If desired, pick the next higher horsepower to eliminate this service factor useage. Refer to the Optisizer Selection Program for actual BHP at any performance point. Quickship Program Most models and many optional accessories are available on the Quickship Program. This provides rapid delivery of standard products so that tight project deadlines can be met and downtime on replacement work can be held to a minimum. Delivery options may include: 5 and 0 day shipments. Optisizer Selection Program Please refer to Jenco Optisizer Program for fan curve, submittal information and other details of this series and other Jenco products. Contact you representative or factory for a copy. Log onto Jenco's web site for additional information at: www.jencofan.com. Optional Accessories Wall Housing Wall Collar s Mounting Flanges side Guard Frontside Guard Rainhood Guard Paint Finishes Electrical Accessories MODEL L - Level Construction Panel Drive Material (Ga.or inches th.) & Bearing Supports Spider Propeller Blade Steel Steel Alum Shaft Diameter (in.) Avg. Weight (lbs.) 4 6 0 0 /8 6 0.080 7/6 T 60 48 6 0 0 /8 6 0.080 7/6 5T 0 54 4 0 0 /8 6 0.080 /6 56T 500 60 4 0 0 /8 6 0.080 /6 56T 50 7 0 0 /8 6 0.080 /6 56T 600 All specifications are subject to change without notice unless approved in submittal by Jenco. 4
dimensional data Model LC Sidewall Propeller Level Construction Model L Sidewall Propeller Level Construction Model L Sidewall Propeller Level Construction A Sq B C D E F O.D. Sq Flange 0 4 5 /4 5 / 4 0 7 / /4 5 8 / 0 6 7 / /4 5 4 4 / 6 4 7 / /4 5 4 40 / 4 48 7 / /4 6 4 46 / 48 54 7 / /4 6 4 5 / 54 60 7 / /4 0 6 58 / 60 66 7 / /4 0 6 64 / Dimensions shown in inches. A Sq B C D E F O.D. Sq Flange 4 0 7 / /4 6 8 / 0 6 7 / /4 6 4 / 6 4 7 / /4 6 40 / 4 48 7 / /4 6 46 / 48 54 7 / /4 6 5 / 54 60 7 / /4 6 58 / 60 66 7 / /4 4 8 64 / Dimensions shown in inches. A Sq B C D E F O.D. Sq Flange 4 48 7 / /4 4 8 46 / 48 54 7 / /4 4 8 5 / 54 60 7 / /4 4 8 58 / 60 66 7 / /4 4 8 64 / 7 80 8 /4 4 8 78 / Dimensions shown in inches. Jenco Limited Warranty Jenco (manufacturer), 69 Powers Avenue, Jacksonville, Florida 7, warrants equipment of its manufacture to be free from defects in design, materials and workmanship (exclusive of abrasion, corrosion or erosion) for one () year from the date of shipment to the original purchaser or the date of notification of readiness to ship. warranty is one () year. In order to claim the benefit of this warranty, buyer must notify manufacturer in writing of the claimed defect within ten (0) days after discovering it and return this equipment or parts to the factory with transportation prepaid. In the event of on-site repair, no service technician will be dispatched until manufacturer receives your written purchase order. If any of the following conditions exist, the warranty will be null and void: () Buyer has permitted other persons not approved or authorized by manufacturer to alter, adjust, replace or repair the equipment or any part there of. () Buyer has not followed instructions or other directions given in the contract documents or our maintenance manual. () When breakage or other loss or damage is the result of any negligence, misuse or fault on the part of any operator or other person not under our supervision or control. (4) The defect is the result of designs or drawings made, furnished or specified by others. (5) In the case of goods not manufactured but supplied by the manufacturer as part of a contract, manufacturer shall only be liable to the same extent that our supplier is to manufacturer, not to exceed any liability manufacturer would have for warranty on our own equipment. (6) Buyer has not paid in full any invoices submitted to buyer which are due for payment. (7) Unusual wear and tear of the equipment. Statements relating to the product, its use or installation made prior to the execution of the agreement, are not warranties except to the extent that the contrary is expressly set forth herein. It is understood that such statements were not intended to, and did not, form a part of the agreement; they were merely made in the course of negotiations of the parties. This warranty is in lieu of any other express or implied warranties, including any implied warranty of merchantability or fitness for any particular purpose. Our sole and exclusive obligation under this warranty is to repair or replace defective equipment or parts or, at our option, to pay the reasonable cost of repair or replacement. Buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages, damages for lost profits or sales, or damages for injuries to person or property) shall be available. Notwithstanding the above, the total amount that may in any event be payable in settlement of liability, however incurred, shall not exceed the contract price. 5
pressure loss guide for accessories Use the estimated pressure drop graphs to help select the proper exhaust or supply fan package that will deliver the desired airflow. Enter the graph from the bottom at the specified CFM and move vertically upward to the fan curve for the desired fan size, then horizontally to the left and read the estimated static pressure drop resulting from these typical accessory packages. Add the accessory pressure loss to the system (or building) design static pressure loss to obtain the total static pressure loss to be used for the proper fan selection. Exhaust Airflow with Wall Housing Gravity Rainhood side Guard Supply Airflow with Wall Housing Gravity Rainhood side Guard Standard Mounting Arrangements Wall housing flush with outside wall Wall housing centered within wall NOTE: Supply applications have the fan venturi spun on the opposite side of the fans shown above. The fans shown are exhaust. Rainhoods are required on supply applications and recommended on exhaust applications where additional weather protection is desired. Exhaust and/or supply fans installed as shown should be serviced from the interior of the building. Where service is required from the exterior of the building, consult the factory or representative for recommendations. All bracing shown is field provided. Field flashing and caulking of wall housing seams and unused mounting holes, will ensure a weather resistant installation. 6 Wall housing flush with inside wall
R performance data Model LC 0 Limits Model Panel OD Square Min. Wall OD Approx. Wt LC 50 56H 4 5 / / 85 Level Construction Model LC 0 HP /4 / / BHP Sones (0.00 SP) Static Pressure (Inches W.G).000.00.5.50.00.50.00.75.500 0.5 905 0.5 774 64 47 - - - - - 0.7 90 0.8 87 45 9 89 - - - - 0.8 90.0 879 48 70 46 900 - - - - 0.9 945. 94 55 44 4 00 - - - - 0.0 955.5 98 600 49 75 067 - - - - 0. 990. 49 76 658 550 8 - - - - 0.4 000.5 47 809 706 599 4 - - - - 0.6 05.8 4 878 776 67 48 - - - - 0.8 00. 496 947 847 746 5 7 - - - 0.40 050.5 479 408 94 84 6 - - - 0.47 0 4.8 469 4 4 48 9 689 - - - 0.50 5 5. 469 478 49 499 4009 776 45 - - 0.55 45 5.5 4775 4468 48 49 408 890 59 78-0.57 60 5.9 488 456 445 464 48 97 694 959-0.60 80 6.4 49 465 454 4457 480 408 8 8-0.70 60 8. 555 498 4905 487 4664 449 49 875-0.75 95 9. 540 55 506 4987 489 4666 4484 47-0.79 0 9.7 5505 545 574 50 4947 4788 466 478-0.8 5 0 5568 5 54 569 508 486 469 47-0.90 50 0 560 577 508 57 5088 494 4770 446 58 Performance ratings do not include the effects of appurtenances (accessories). Power ratings (BHP) do not include transmission losses. Performance certified is for installation type A-free inlet, free outlet. The sound ratings shown are loudness values in fan sones @ 5' (.5m) in a hemispherical free field calculated per AMCA Standard 0. Values shown are for installation Type A-Free inlet fan sone levels. Due to air stream cooling, the motor loading into the service factor shown does not overheat the motor and is within NEMA recommended limits. BHP at most static pressure points is less than the maximum power shown - in many cases substantially less. Use Optisizer to see the exact BHP for your selection. SOUND and PERFORMANCE MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Jenco, Div. of Soler & Palau Ventilation Group, certifies that the models shown herein are licensed to bear the AMCA Seal. The ratings shown are based on test and procedures performed in accordance with AMCA Publication and AMCA Publication and comply with the requirement of the AMCA Certified Ratings Program. UL Standard 705 7
R Model LC and Model L 4 Model Limits Panel OD Square Min. Wall OD Approx. Wt LC 00 45T 0 8 / 90 L 45 45T 0 8 / 0 SOUND and PERFORMANCE MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Jenco, Div. of Soler & Palau Ventilation Group, certifies that the models shown herein are licensed to bear the AMCA Seal. The ratings shown are based on test and procedures performed in accordance with AMCA Publication and AMCA Publication and comply with the requirement of the AMCA Certified Ratings Program. UL Standard 705 Level Construction Level Construction Model LC 4 Model L 4 HP /4 / / / /4 / / / BHP Sones (0.00 SP) 8 Static Pressure (Inches W.G).000.00.5.50.00.50.00.75.500.65 0.5 555 9.0 49 468 905 574 56 - - - - - 0.7 570 9.4 5065 4 4085 787 460 - - - - - 0.0 600 0. 5 465 44 480 50 69 - - - - 0. 65 0.9 555 49 4709 448 89 - - - - - 0.6 645.6 57 57 496 475 487 - - - - - 0.4 660. 5864 568 5086 4885 498 70 - - - - 0.50 75 4.0 65 585 5658 5487 5097 459 - - - - 0.54 75 4.7 65 60 586 5699 5 4877 - - - - 0.58 750 5. 6664 657 60 5856 5504 508 455 - - - 0.60 760 5.7 675 654 6 5959 567 5 4686 - - - 0.75 80 7.9 786 68 6704 6570 676 594 5577 - - - 0.80 840 8.6 7464 70 6898 6770 6489 670 5804 - - - 0.85 855 9. 7597 76 7044 698 6646 640 599 56 - - 0.90 875 9.8 7775 75 77 76 6855 656 64 5600 - -.00 905 804 765 754 7409 76 6890 6586 6040 - -.0 95 808 796 780 7700 7467 7 697 647 - -.0 950 844 8057 795 7845 768 769 7094 665 5559 -.50 05 5 996 8847 8754 8658 8458 844 80 768 686 -.65 070 7 9507 970 908 8989 8798 8595 878 809 708 -.8 00 8 9774 9447 96 97 9088 8894 8687 847 7688 6808 0.5 540 9.9 57 4075 6 7 - - - - - - 0.7 555 0.9 5464 490 707 948 - - - - - - 0.0 575. 566 4559 4098 07 - - - - - - 0. 590. 5809 475 446 647 - - - - - - 0.6 605 4. 5957 494 4574 995 908 - - - - - 0.40 60 6. 60 555 496 449 47 - - - - - 0.50 670 7.9 6597 5740 5446 56 95 68 - - - - 0.57 685 8.5 6744 597 564 56 499 64 859 - - - 0.60 700 9.0 689 6090 58 558 4645 568 04 - - - 0.75 740 786 654 60 604 596 40 549 88 - - 0.80 765 75 686 6605 654 578 4786 88 86 - - 0.86 795 787 78 695 674 605 5455 45 555 - - 0.90 85 4 804 750 777 6964 647 587 476 807 - -.00 855 6 848 777 768 74 698 6460 566 47 - -.05 870 7 8566 790 7779 7604 770 6677 5958 455 - -. 890 8 876 89 79 78 740 695 65 485 - -.0 90 9 8960 847 805 8055 7667 70 6668 546 - -.50 975 9600 90 8890 8756 8440 8045 768 6707 484 -.66 05 5 9994 944 908 980 8899 854 845 746 5409 -.80 045 8 089 974 960 9496 96 8905 856 7880 5900 -.00 075 4 0584 0050 990 98 9566 960 8900 800 6600 -.0 5 46 0978 0459 04 09 9995 974 996 8848 75 5700.7 45 5 7 0766 065 0540 05 0065 9758 97 808 604 Performance ratings do not include the effects of appurtenances (accessories). Power ratings (BHP) do not include transmission losses. Performance certified is for installation type A-free inlet, free outlet. The sound ratings shown are loudness values in fan sones @ 5' (.5m) in a hemispherical free field calculated per AMCA Standard 0. Values shown are for installation Type A-Free inlet fan sone levels. Due to air stream cooling, the motor loading into the service factor shown does not overheat the motor and is within NEMA recommended limits. BHP at most static pressure points is less than the maximum power shown - in many cases substantially less. Use Optisizer to see the exact BHP for your selection.
R Model LC and Model L 0 Level Construction Level Construction Model Limits Panel OD Square Min. Wall 9 OD Approx. Wt LC 85 45T 6 7 4 / 00 L 070 8T 6 7 4 / 80 Model LC 0 Model L 0 HP /4 / / / / / / BHP Sones (0.00 SP) MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Static Pressure (Inches W.G).000.00.5.50.00.50.00.75.500 0.5 45 8. 6956 5509 496 45 - - - - - 0.7 45 8.6 79 575 5 4608 - - - - - 0.0 450 9.0 765 606 557 504 - - - - - 0. 465 9.5 760 670 59 54 - - - - - 0.6 480 9.9 7856 6665 670 5794 - - - - - 0.40 495 0.5 80 6954 660 65 507 - - - - 0.50 55.0 8756 7709 749 7074 6 - - - - 0.55 550.7 900 7988 7709 7400 6586 55 - - - 0.59 565. 947 87 7995 77 6949 605 - - - 0.75 60 5. 998 97 889 8589 7995 74 65 - - 0.8 60 6. 0 9487 96 8968 846 778 6945 - - 0.90 650 7. 068 985 9594 94 8857 898 747 - -.00 670 8.0 0965 06 9969 976 95 8665 7978 6549 -. 695 9. 75 0665 044 088 978 98 858 750 -.0 75 0 70 0 080 0565 00 9659 9098 805 -.50 770 60 990 798 589 5 075 098 947 -.6 790 99 9 56 956 56 5 07 9899 88.78 85 4 9 77 599 4 000 609 048 90 0. 480 9.7 7675 647 5879 584 - - - - - 0.6 495 0. 795 6706 64 5678 - - - - - 0.40 505 0.7 8075 6895 648 59 478 - - - - 0.50 550.6 8794 770 74 705 5986 - - - - 0.56 570.6 94 8078 7809 7479 656 - - - - 0.60 585 4.4 954 845 8087 7799 6896 - - - - 0.75 60 7.6 007 946 890 8659 799 7096 - - - 0.8 650 8.4 09 9499 958 906 8455 7609 664 - - 0.90 670 9. 07 9850 964 990 8890 80 700 - -.00 685 9.9 095 0 988 9659 994 8460 768 5700 -.0 70 5 0546 05 006 967 9068 884 680 -.0 75 75 0978 0766 0550 07 967 8900 7679 -.50 795 5 7 004 8 65 6 086 0 99 -.65 80 6 48 4 054 67 0 0876 9908 -.80 845 7 5 85 67 490 6 760 78 050 -.00 875 9 99 56 85 00 65 0 948 9600. 905 4470 859 696 58 8 840 504 907 099.40 90 4870 478 49 957 6 84 96 45 09.00 005 7 6069 555 58 54 490 468 408 855 846.0 040 4 669 605 5967 585 554 55 490 4495 600.60 070 44 709 660 6467 60 6049 576 5465 508 479 SOUND and PERFORMANCE Jenco, Div. of Soler & Palau Ventilation Group, certifies that the models shown herein are licensed to bear the AMCA Seal. The ratings shown are based on test and procedures performed in accordance with AMCA Publication and AMCA Publication and comply with the requirement of the AMCA Certified Ratings Program. UL Standard 705 Performance ratings do not include the effects of appurtenances (accessories). Power ratings (BHP) do not include transmission losses. Performance certified is for installation type A-free inlet, free outlet. The sound ratings shown are loudness values in fan sones @ 5' (.5m) in a hemispherical free field calculated per AMCA Standard 0. Values shown are for installation Type A-Free inlet fan sone levels. Due to air stream cooling, the motor loading into the service factor shown does not overheat the motor and is within NEMA recommended limits. BHP at most static pressure points is less than the maximum power shown - in many cases substantially less. Use Optisizer to see the exact BHP for your selection.
R Model LC and Model L 6 Model Limits Panel OD Square Min. Wall OD Approx. Wt LC 695 45T 4 4 40 / 05 L 845 84T 4 4 40 / 5 SOUND and PERFORMANCE MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Jenco, Div. of Soler & Palau Ventilation Group, certifies that the models shown herein are licensed to bear the AMCA Seal. The ratings shown are based on test and procedures performed in accordance with AMCA Publication and AMCA Publication and comply with the requirement of the AMCA Certified Ratings Program. UL Standard 705 Level Construction Level Construction Model LC 6 Model L 6 HP / / / / / 5 BHP Sones (0.00 SP) Static Pressure (Inches W.G).000.00.5.50.00.50.00.75.500.65.750 0. 60 8.5 997 7580 675 557 - - - - - - - 0.5 70 8.9 00 797 75 6 - - - - - - - 0.4 90 9.7 0755 8745 7976 790 - - - - - - - 0.50 45 0.8 444 96 8967 87 6 - - - - - - 0.55 40.5 858 06 9550 8849 740 - - - - - - 0.59 440.9 0449 99 948 7840 - - - - - - 0.75 475.7 098 556 06 97 787 - - - - - 0.8 490 4.5 5 0 60 6 9954 8675 - - - - - 0.90 505 5. 96 485 00 686 0557 948 784 - - - -.00 55 6.4 4477 0 7 48 45 087 8897 - - - -.09 540 7. 489 56 99 84 90 0809 965 - - - -.9 555 8. 505 408 66 495 49 07 - - - -.50 600 0 6545 57 5048 470 4055 95 86 069 - - -.58 60 68 567 55 509 48 577 590 076 - - -.79 65 75 64 6 580 586 4497 578 46 - - -.00 655 806 700 67 645 589 589 466 975 9909 - -. 680 4 875 777 746 777 6600 604 5 996 6 - -.7 695 5 965 876 7907 76 7065 6499 5859 4594 6 - - 0.50 70 0. 0407 8644 78 7060 - - - - - - - 0.55 80 0.6 0689 908 84 75 5997 - - - - - - 0.60 90. 0970 99 8667 794 6466 - - - - - - 0.75 40.6 84 040 99 98 788 646 - - - - - 0.8 45.5 6 09 046 98 8505 78 - - - - - 0.90 450 4. 658 90 0989 0460 956 7800 - - - - -.00 465 5. 080 858 497 04 9780 858 700 - - - -.0 480 6.0 50 0 99 585 098 9 8000 - - - -.0 495 6.8 9 779 478 07 07 989 8600 - - - -.50 50 8.9 4908 88 570 74 490 5 09 8670 - - -.6 545 9.8 50 488 400 757 045 969 0954 945 - - -.79 565 589 4885 469 48 754 84 79 05 - - -.00 585 6455 5479 544 500 446 667 67 6 - - -.0 605 707 607 5845 56 5099 447 46 06 9600 - -.9 60 4 749 654 69 6069 5586 4967 4 697 076 - -.00 665 7 8705 786 76 745 6998 6506 5886 4557 404 0 -.0 690 8 9408 8568 869 87 7766 7 6776 564 547 457 -.60 75 0 0 997 905 894 857 89 76 6679 46 500-5.00 795 6 6 6 447 74 09 058 06 9564 7987 664 487 5.56 85 8 06 489 0 54 8 488 44 056 95 74 5678 5.97 845 40 768 067 90 79 45 090 757 4 000 87 6588 Performance ratings do not include the effects of appurtenances (accessories). Power ratings (BHP) do not include transmission losses. Performance certified is for installation type A-free inlet, free outlet. The sound ratings shown are loudness values in fan sones @ 5' (.5m) in a hemispherical free field calculated per AMCA Standard 0. Values shown are for installation Type A-Free inlet fan sone levels. Due to air stream cooling, the motor loading into the service factor shown does not overheat the motor and is within NEMA recommended limits. BHP at most static pressure points is less than the maximum power shown - in many cases substantially less. Use Optisizer to see the exact BHP for your selection. 0
R Model LC, Model L and Model L 4 Model Limits Panel OD Square Min. Wall OD Approx. Wt LC 550 45T 48 49 46 / 0 L 745 84T 48 49 46 / 5 L 850 T 48 49 46 / 60 SOUND and PERFORMANCE MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Jenco, Div. of Soler & Palau Ventilation Group, certifies that the models shown herein are licensed to bear the AMCA Seal. The ratings shown are based on test and procedures performed in accordance with AMCA Publication and AMCA Publication and comply with the requirement of the AMCA Certified Ratings Program. UL Standard 705 Level Construction Level Construction Level Model LC 4 Model L 4 Model L 4 HP / / / / / / 5 7 / BHP Sones (0.0 SP) Static Pressure (Inches W.G).000.00.5.50.00.50.00.75.500.65.750 0. 85 8. 09 84 68 - - - - - - - - 0.7 95 8. 74 8967 7579 - - - - - - - - 0.4 05 8.4 7 9658 849 548 - - - - - - - 0.50 5 8.8 407 0969 975 848 - - - - - - - 0.54 5 9. 4469 549 080 905 - - - - - - - 0.60 45 9.8 490 09 07 9960 - - - - - - - 0.75 75.4 697 705 98 98 9768 - - - - - - 0.8 85.0 669 48 498 606 069 - - - - - - 0.90 95.6 7060 474 4044 5 85 79 - - - - -.00 40.4 7708 5474 484 48 9895 - - - - -. 45 4. 856 64 568 4966 7 4 6467 - - - -.0 45 4.9 8788 670 68 5508 9 8 8485 - - - -.50 470 6.9 000 8400 7874 76 68 449 885 - - - -.65 485 7.9 0948 99 8609 8095 6964 5460 900 998 - - -.8 500 8.8 596 98 99 8845 7784 6470 4848 87 - - -.00 55 9.8 4 054 0067 9587 858 740 5805 57 - - -. 55 07 48 09 0566 96 856 790 5068 - - -.40 550 755 8 746 95 088 99 890 604 - - - 0. 85 7.8 0509 7477 567 6 - - - - - - - 0.6 90 8.0 0694 7789 64 404 - - - - - - - 0.40 00 8. 06 88 706 4906 - - - - - - - 0.50 5 8.9 984 967 8755 764 - - - - - - - 0.55 5 9.4 5 049 947 804 - - - - - - - 0.60 45 0.0 7 06 990 890 - - - - - - - 0.75 70.5 644 8 04 867 - - - - - - 0.84 85.4 497 5 84 06 9474 6 - - - - - 0.90 95.0 4566 97 6 697 0087 74 - - - - -.00 405.7 494 406 80 78 0697 879 - - - - -.0 40 4.6 5487 404 56 889 606 9898 65 - - - -.0 45 5.7 604 4664 406 604 449 0877 805 - - - -.50 470 8.0 7 6089 576 565 474 00 506 74 - - -.66 485 9.0 7884 6689 69 594 4884 846 48 8858 - - -.8 495 9.6 85 7088 6750 675 554 466 07 998 - - -.00 55 8990 7880 7564 7 65 545 450 66 - - -.4 55 978 8666 869 805 77 699 568 458 - - -.4 550 08 95 8969 8666 7959 7006 6 460 98 - -.00 590 6 756 0806 0549 080 9690 898 804 678 69 807 -. 60 7 494 578 077 054 9855 8985 778 5060 9786 688.60 65 8 047 56 98 67 4 05 977 857 5977 795 5.00 700 4 58 504 488 4606 464 687 56 0 04 796 4 5.5 70 6 6550 5785 5586 58 4957 450 4005 060 99 96 6540 6.07 745 8 747 674 654 647 594 55 5049 4 500 0666 8 7.50 800 4 9500 886 869 8460 809 7705 798 668 50 570 68 8.7 85 46 04 9759 9589 946 906 869 805 7676 65 4778 47 8.9 850 48 44 070 057 069 007 967 904 870 7497 5965 45 Performance ratings do not include the effects of appurtenances (accessories). Power ratings (BHP) do not include transmission losses. Performance certified is for installation type A-free inlet, free outlet. The sound ratings shown are loudness values in fan sones @ 5' (.5m) in a hemispherical free field calculated per AMCA Standard 0. Values shown are for installation Type A-Free inlet fan sone levels. Due to air stream cooling, the motor loading into the service factor shown does not overheat the motor and is within NEMA recommended limits. BHP at most static pressure points is less than the maximum power shown - in many cases substantially less. Use Optisizer to see the exact BHP for your selection.
R Model LC, Model L and Model L 48 Model Limits Panel OD Square Min. Wall OD Approx. Wt LC 455 45T 54 55 5 / 5 L 605 84T 54 55 5 / 00 L 765 5T 54 55 5 / 0 SOUND and PERFORMANCE MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Jenco, Div. of Soler & Palau Ventilation Group, certifies that the models shown herein are licensed to bear the AMCA Seal. The ratings shown are based on test and procedures performed in accordance with AMCA Publication and AMCA Publication and comply with the requirement of the AMCA Certified Ratings Program. UL Standard 705 Level Construction Level Construction Level Construction Model LC 48 Model L 48 Model L 48 HP / / / / 5 7 / 0 BHP Sones (0.0 SP) Static Pressure (Inches W.G).000.00.5.50.00.50.00.75.500.65.750 0.50 70 9.5 679 96 99 - - - - - - - - 0.56 80 9.7 759 96 6659 - - - - - - - 0.6 90 0.0 7979 84 99 0077 - - - - - - - 0.69 00 0.4 8599 4684 9 4 - - - - - - - 0.75 0 0.9 99 5459 47 556 - - - - - - - 0.8 0.6 989 60 50 600 - - - - - - - 0.9 0. 0459 6949 5969 4584 0759 - - - - - -.00 40.7 079 7678 6778 556 6 - - - - - -.09 50.4 699 84 754 649 606 - - - - - -.4 55.7 009 8777 797 696 474 - - - - - -. 65 4. 69 9504 8659 7784 54 0868 - - - - -.50 90 5.9 479 96 0488 97 770 5058 - - - - -.6 400 6.7 4799 004 9 045 8668 687 97 - - - -.8 45 7.8 579 054 06 548 9994 7746 4950 - - - -.00 40 8.9 6659 409 8 647 7 95 689 - - - -.6 440 9.6 779 4779 409 77 98 094 799 - - - -.9 455 809 5800 548 446 07 574 9479 58 - - - 0.5 65 8.9 4897 05 960 778 - - - - - - - 0.55 70 9. 578 448 0050 8090 - - - - - - - 0.60 80 9. 5740 85 0907 944 - - - - - - - 0.69 95 0. 6584 46 04 094 - - - - - - - 0.75 00 0.4 6865 840 69 76 700 - - - - - - 0.8 0. 747 4578 485 904 - - - - - - 0.90 0.9 7989 500 490 09 0504 - - - - - - 0.9 5. 870 5656 468 50 096 - - - - - -.00 5.0 88 65 544 488 8 779 - - - - -. 45.8 994 70 68 5 04 985 - - - - -. 55 4.6 9957 770 6908 600 866 86 - - - - -.50 80 6.4 6 90 8656 7879 60 405 9 - - - -.68 95 7.5 05 06 9664 8958 794 54 9 - - - -.80 405 8. 767 0884 0 966 8094 684 49 - - - -.00 40 9.4 6 808 9 0689 95 7504 579 - - - -.0 40 0 47 49 96 6 0000 865 6577 76 - - -.40 445 506 864 50 095 9608 7847 59 - - -.00 480 4 698 546 500 4580 55 05 087 8470 09 - -.6 495 5 787 6 59 554 4564 40 080 974 509 - -.6 50 7 8670 7 688 649 5556 4479 45 054 7098 - - 5.00 565 76 0464 07 978 905 8 76 5589 5 848-5.44 585 886 65 0980 090 955 8650 705 969 074-6. 605 5 400 80 49 74 56 08 000 857 5707 58 4450 7.50 650 40 6540 549 5 484 44 66 945 75 96 644 60 8. 670 4 7664 6578 600 600 5444 4844 409 0886 890 567 9.05 695 45 9070 80 7757 7487 697 667 5770 4774 70 006 7485 0.00 70 48 40475 9466 90 895 84 7880 74 640 450 04 9666 0.88 740 50 4600 4068 4069 408 9607 908 8540 7674 597 846 40.00 765 5 4005 4056 486 4574 408 40580 4006 94 765 574 496 Performance ratings do not include the effects of appurtenances (accessories). Power ratings (BHP) do not include transmission losses. Performance certified is for installation type A-free inlet, free outlet. The sound ratings shown are loudness values in fan sones @ 5' (.5m) in a hemispherical free field calculated per AMCA Standard 0. Values shown are for installation Type A-Free inlet fan sone levels. Due to air stream cooling, the motor loading into the service factor shown does not overheat the motor and is within NEMA recommended limits. BHP at most static pressure points is less than the maximum power shown - in many cases substantially less. Use Optisizer to see the exact BHP for your selection.
R Model LC, Model L and Model L 54 Model Limits Panel OD Square Min. Wall OD Approx. Wt LC 45 8T 60 6 58 / 40 L 55 84T 60 6 58 / 400 L 740 56T 60 6 58 / 500 SOUND and PERFORMANCE MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Jenco, Div. of Soler & Palau Ventilation Group, certifies that the models shown herein are licensed to bear the AMCA Seal. The ratings shown are based on test and procedures performed in accordance with AMCA Publication and AMCA Publication and comply with the requirement of the AMCA Certified Ratings Program. UL Standard 705 Level Construction Level Construction Level Construction Model LC 54 Model L 54 Model L 54 HP / / 5 7 / 0 5 BHP Sones (0.5 SP) Static Pressure (Inches W.G).000.5.50.00.50.00.75.500.65.750 0.75 50 9.8 65 4977 0 - - - - - - - 0.8 60 0.4 58 6507 479 - - - - - - - 0.9 70.0 84 79 55 0 - - - - - -.00 75.4 87 8559 6095 60 - - - - - -.09 85. 468 970 756 486 - - - - - -.0 95. 5550 085 9097 6699 - - - - - -.50 5 4.8 78 9 6 968 699 - - - - -.6 5 5.5 848 950 757 8 5785 - - - - -.84 40 6.8 9447 5449 47 09 98 - - - - -.00 50 7.7 0 644 544 459 067 599 - - - -.9 60 8.5 79 7408 647 565 6456 - - - -.8 70 9.4 045 875 7445 649 69 965 - - - -.00 400 464 6 040 950 754 45 009 - - -.5 45 594 648 85 09 9 6686 74 - - -.60 45 4 6809 585 8 05 090 800 4785 5677 - -.00 80.9 680 7068 540 0747 - - - - - -.08 90.8 490 889 6585 5 - - - - - -.0 00. 400 945 7847 4940 - - - - - -.50 5 4.7 65 07 088 80 506 - - - - -.66 5 5. 75 05 99 967 6645 - - - - -.8 45 5.9 7945 4009 055 049 7977 94 - - - -.00 55 6.5 8755 495 4076 69 967 60 - - - -.4 70 7.4 9970 67 554 506 0904 8665 - - - -.4 80 8. 0780 750 6496 464 0 994 875 - - -.00 405 9.8 805 9495 88 707 55 86 959 - - -.6 40 400 086 088 879 7006 4696 705 - - -.6 45 55 58 07 866 6595 500 - - - 5.00 485 7 985 640 594 486 677 00 9567 5066 - - 5.5 495 8 40095 784 6789 576 464 9 080 676 9008-6.04 55 9 475 8988 850 7550 6487 5 44 860 40-6.94 540 4740 40 4065 974 877 777 5876 600 7746 976 7.50 555 44955 478 490 4046 406 9 746 508 9564 4604 8.60 580 5 46980 44488 44055 406 456 444 990 6579 47 8797 0.00 60 8 4940 470 46594 4578 44978 448 4758 997 68 66.06 60 40 500 48690 488 4749 467 459 4469 405 865 4954.5 650 4 5650 5064 49967 4995 4849 4768 46454 444 4077 764 5.00 700 48 56700 5454 5464 544 575 504 50955 4896 4667 4558 6.45 70 5 580 5607 5587 55 5440 5747 57 5080 48684 459 7.85 740 5 59940 5787 57509 56809 560 55464 54469 5675 50659 4879 Performance ratings do not include the effects of appurtenances (accessories). Power ratings (BHP) do not include transmission losses. Performance certified is for installation type A-free inlet, free outlet. The sound ratings shown are loudness values in fan sones @ 5' (.5m) in a hemispherical free field calculated per AMCA Standard 0. Values shown are for installation Type A-Free inlet fan sone levels. Due to air stream cooling, the motor loading into the service factor shown does not overheat the motor and is within NEMA recommended limits. BHP at most static pressure points is less than the maximum power shown - in many cases substantially less. Use Optisizer to see the exact BHP for your selection.
R Model LC, Model L and Model L 60 Model Limits Panel OD Square Min. Wall OD Approx. Wt LC 80 8T 66 67 64 / 85 L 460 84T 66 67 64 / 490 L 700 56T 66 67 64 / 50 SOUND and PERFORMANCE MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Jenco, Div. of Soler & Palau Ventilation Group, certifies that the models shown herein are licensed to bear the AMCA Seal. The ratings shown are based on test and procedures performed in accordance with AMCA Publication and AMCA Publication and comply with the requirement of the AMCA Certified Ratings Program. UL Standard 705 Level Construction Level Construction Level Construction Model LC 60 Model L 60 Model L 60 HP / / 5 7 / 0 5 BHP Sones (0.00 SP) Static Pressure (Inches W.G).000.5.50.00.50.75.500.65.750.000.00 50 0. 6878 0089 667 - - - - - - -.08 55 0.7 746 085 8009 - - - - - - -. 65.5 849 75 009 - - - - - - -.50 85.0 064 504 80 0999 - - - - - -.69 95.9 77 669 47 844 - - - - - -.75 00 4. 54 70 54 649 - - - - - -.00 0 5. 9 87 684 576 88 - - - - -. 5 6. 494 0 8846 744 6 - - - - -.44 5 7. 607 464 059 875 599 - - - - -.0 60 9. 8705 4490 67 5 97 54 - - - -.9 70 0 9780 567 468 40 08 75 - - - -.56 80 40855 686 5849 47 44 95 - - - -.00 50 9.9 56 7744 584 - - - - - - -.08 60 0.6 6656 95 768 - - - - - - -. 70. 768 0986 8860 56 - - - - - -.50 90.7 97 756 06 8500 - - - - - -.67 00.4 0757 50 69 00 650 - - - - -.8 0 4. 78 680 507 5 876 - - - - -.00 0 5.0 808 75 64 0 007 - - - - -. 5 5.4 0 8 696 8 080 - - - - -. 0 5.8 8 8744 7594 4667 569 - - - - -.00 65 9.0 74 99 95 98 69 950 - - - -.8 80 0 8959 4674 74 7 990 56 - - - -.64 90 9984 58 494 979 09 409 - - - - 5.00 45 5 44598 4086 40 8488 6744 0 599 - - - 5.60 450 6 466 459 4809 4075 8594 46 790 - - - 5.98 460 7 476 468 496 4454 980 55 9479 - - - 7.0 485 9 4974 465 45700 4459 4869 8864 48 86 - - 7.50 495 0 50749 4744 4680 4550 44065 4096 4740 9870 - - 7.9 505 5774 4857 4790 466 455 4497 64 497 - - 9.09 50 4 548 5 5066 4947 4880 44658 4068 54 06-0.00 545 5 55875 5847 568 507 499 465 4747 758 76-0.78 560 7 574 54459 5895 5767 567 4865 4487 984 5577 -.98 580 9 59464 5660 56058 54969 5868 508 475 409 869-5.00 65 44 64077 6406 60896 59886 58874 5689 577 500 4597 7596 6.48 645 47 668 65 607 6056 6078 5859 55646 567 4876 4085 7.98 665 49 6878 65654 657 649 67 6084 58098 5540 597 4894 Performance ratings do not include the effects of appurtenances (accessories). Power ratings (BHP) do not include transmission losses. Performance certified is for installation type A-free inlet, free outlet. The sound ratings shown are loudness values in fan sones @ 5' (.5m) in a hemispherical free field calculated per AMCA Standard 0. Values shown are for installation Type A-Free inlet fan sone levels. Due to air stream cooling, the motor loading into the service factor shown does not overheat the motor and is within NEMA recommended limits. BHP at most static pressure points is less than the maximum power shown - in many cases substantially less. Use Optisizer to see the exact BHP for your selection. 4
R Model L 7 Model Limits Panel OD Square Min. Wall OD Approx. Wt L 545 56T 80 8 78 / 600 SOUND and PERFORMANCE MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Jenco, Div. of Soler & Palau Ventilation Group, certifies that the models shown herein are licensed to bear the AMCA Seal. The ratings shown are based on test and procedures performed in accordance with AMCA Publication and AMCA Publication and comply with the requirement of the AMCA Certified Ratings Program. Level Construction Model L 7 HP / 5 7 0 5 BHP Sones (0.00 SP) Static Pressure (Inches W.G) UL Standard 705.000.5.00.50.00.75.500.65.750.000.9 5 59 0805 - - - - - - - -.50 5 6690 490 76 - - - - - - -.77 50 5 90 8557 6766 - - - - - - -.00 60 7 4059 0797 987 85 - - - - - -. 70 8 454 05 70 559 - - - - - -.6 75 9 495 470 988 768 - - - - - -.00 95 4 46058 8778 898 480 688 - - - - -. 05 6 4769 4064 7 64 049 - - - - -.54 5 9 4980 44 589 8644 0 - - - - - 4.6 5 44 50 4597 4004 44 894 0547 - - - - 5.00 50 48 54645 48505 440 9490 58 585 - - - - 5.98 75 56 58548 575 4997 456 4060 470 979 - - - 6.44 85 60 6009 5449 540 476 470 4888 5 - - - 7.50 405 64 6 5779 5480 595 4897 9949 9577 75 - - 8.7 45 67 6654 6 580 569 5989 4794 540 4005 - - 0.00 445 69 69477 6445 6744 59908 57687 56 409 060 905 -.04 460 7 789 66908 6494 6555 606 5547 4409 54 497 -.5 475 74 7460 697 6688 6565 687 590 4890 955 947-5.00 50 79 7965 7500 770 754 69590 66984 5976 489 4096-6.4 55 8 8967 77547 75 7700 790 69767 6695 55 44585 6079 8.6 545 85 85089 80799 78545 77078 7569 770 67480 5989 49467 867 Performance ratings do not include the effects of appurtenances (accessories). Power ratings (BHP) do not include transmission losses. Performance certified is for installation type A-free inlet, free outlet. The sound ratings shown are loudness values in fan sones @ 5' (.5m) in a hemispherical free field calculated per AMCA Standard 0. Values shown are for installation Type A-Free inlet fan sone levels. Due to air stream cooling, the motor loading into the service factor shown does not overheat the motor and is within NEMA recommended limits. BHP at most static pressure points is less than the maximum power shown - in many cases substantially less. Use Optisizer to see the exact BHP for your selection. 5
accessories Wall Collar and Optional Accessories Wall Collar The heavy-gauge, all G-90 galvanized mounting collar provides a simple solution to installing a fan in a rough wall opening when a rear safety guard is NOT required. A front wire guard, shutter, and/or rainhood can be attached to the front prepunched flanges. The wall collar can be used in exhaust or supply applications for all fan sizes. The wall collar is mounted with the fan on the interior side of the building. All collars ship fully assembled with the fan to lessen jobsite installation costs. We strongly recommend rainhoods and motorized shutter for all supply applications as well as for exhaust applications where additional weather protection is desired. Accessories Dimensions Wall Collar Minimum Wall Flat Guard Rainhood 4 side Guard 5 A B Sq C D (O.D) E F Exh/Sup Exhaust/Supply 0 4 /4 5 / 4 / 0 4 /4 4 4 4 0 /4 / 0 8 / 6 8 / 0 4 0 6 /4 7 / 6 4 / 4 / 6 4 6 4 /4 4 / 4 40 / 8 40 / 4 4 4 48 /8 49 / 48 46 / 44 46 / 48 4 48 54 /8 55 / 54 5 / 50 49 / 54 4 54 60 /8 6 / 60 58 / 56 58 / 60 4 60 66 /8 67 / 66 64 / 6 64 / 66 4 7 80 /8 6 8 / 80 78 / 76 7 80 4 (a) Level Construction requires a deeper motorside guard as shown. Unless shown otherwise supply and exhaust dimensions are similar. G H Sheet Metal and Wire side Guard An assembled heavy-gauge G-90 galvanized steel housing is available with front or rear OSHA approved flat wire safety guard with / x in. galvanized welded wire. This housing and guard attaches to the fan panel. It ships pre-assembled to lessen installation costs, but is available knocked-down for field assembly. Optional heavy duty OSHA approved guard is constructed of heavy-gauge aluminum expanded metal. Please note that this style guard is not compatible with the wall collar or wall housing. Adequate clearance must be maintained between fan blade and damper. 6
Wall Housing and Optional Accessories WALL HOUSING This heavy gauge, all galvanized G-90 steel housing provides a simple solution to installing a fan and all required accessories in a rough wall opening. It can be used in exhaust or supply applications and in fan sizes 0 through 7 inch. Depending on space and maintenance requirements, the wall housing may be installed inward or outwards of the building. All housings ship assembled with the fan to lessen job site installation costs. Wire guards, shutters and/or rainhoods may be attached to the pre-punched flange. See pages 6-9 for available accessories. We strongly recommend rainhoods and motorized shutters for all supply applications and whenever additional weather protection is desired.. A (Sq.) O.D Wall Housing Exhaust B Length Supply Minimum Wall Flat Guard Level Levels & Level Levels & (Sq) C (Sq) D (O.D) E F Rainhood 4 0 5 () 44 44 44 5 / 4 / 0 4 /4 4 () 44 44 44 / 0 8 / 6 8 / 0 7 () 44 44 44 7 / 6 4 / 4 / 6 4 () 44 44 44 4 / 4 40 / 8 40 / 4 49 () 44 44 44 49 / 48 46 / 44 46 / 48 55 () 44 44 44 55 / 54 5 / 50 49 / 54 6 44 44 44 44 6 / 60 58 / 56 58 / 60 67 44 44 44 44 67 / 66 64 / 6 64 / 7 8 NA 44 NA 44 8 / 80 78 / 76 7 Note () - 44" long wall housing required when optional motorized damper is selected. Rainhood recommended for supply applications. 7
SIDEWALL PROPELLER FAN ACCESSORIES & OPTIONS Heavy Duty Galvanized Exhaust ized Shutter: This damper has a flanged frame and is designed to fit the inside flanges of the optional wall housing or wall mounting collar. The frame and blades are constructed of galvanized steel and are rated to 000 FPM with proper clearance as provided by all factory accessories. The damper body recesses into the opening for a flush appearance. See page 9 for more details on the electric damper operators. Standard Duty Aluminum Exhaust Gravity Shutter: This damper can greatly reduce the infiltration of outside air and although not completely watertight, will provide weather protection in an economical fashion. Constructed with a galvanized frame and aluminum blades this damper is rated to 000 FPM with the proper clearance as provided by all factory accessories. The damper body is recessed into the opening for a flush appearance. Heavy Duty Galvanized Supply ized Shutter: The motorized option improves weather protection by providing a tighter closure seal and is recommended for all supply applications. Heavy duty dampers are constructed with galvanized frames and blades and are rated to 000 FPM. The damper body is not recessed providing extra clearance between the fan and damper blades. See page 9 for more details on the electric damper operators. Standard Duty Aluminum Supply ized Shutter: The motorized option improves weather protection by providing a tighter closure seal and is recommended for all supply applications. Standard duty dampers are constructed with galvanized frames and aluminum blades and are rated to 000 FPM. The damper body is not recessed providing extra clearance between the fan and damper blades. See page 9 for more details on the electric damper operators. Center Pivot ized - Supply or Exhaust: The flanged frame damper is designed to recess inside the flanges of the optional wall housing or wall mounting collar. The center pivot style damper provides superior weather resistance. Galvanized (optional aluminum) construction is rated to 500 FPM with proper clearance as provided by all factory accessories. See page 9 for more details on the electric damper operators. Rainhoods or Weatherhoods: Designed to provide additional weather protection by partially shielding the wall opening and should be used for all supply applications and whenever additional weather resistance is desired. The galvanized (aluminum optional) hood attaches to the wall housing or wall collar flanges. Field flashing and caulking will reduce moisture penetration. Shown with optional birdscreen. 8
SIDEWALL PROPELLER FAN ACCESSORIES & OPTIONS Safety Guards are strongly recommended to protect personnel from accidental injury and to prevent debris from entering the fan. OSHA approved guards are required in many installations including when the fans are within 7 feet of the floor or work/access area. Standard Duty Flat Wire Guard: The removable safety guard satisfies OSHA requirements when used with the optional wall housing as a motorside (rear) guard. The 6 ga. /" X " welded wire mesh is mounted in a galvanized frame and attaches to the inward flanges of the wall housing. Heavy Duty Flat Wire Guard: The removable safety guard satisfies OSHA requirements when used with the optional wall housing as a motorside (rear) guard. The H.D. expanded aluminum mesh is mounted in a galvanized frame and attaches to the inward flanges of the wall housing. Sheet Metal and Wire side Guard: The OSHA approved safety guard consists of galvanized sides (aluminum optional) plus a flat wire guard (standard duty or heavy duty) factory assembled and attached to motorside (rear) of the fan panel. This guard is not compatible with the wall housing or wall mounting collar. Electric Operators provide more positive open and closed damper positions which helps increase weather resistance. Power open - spring close (POSC) motor and linkage kits are field installed (except for center pivot style) and are available in 4, 0/40, or 460 volts (single phase) and require approximately 0.5 amps at 0//60 power supply. Transformers are available for voltage reduction. For fan motors 5HP and larger, we recommend a factory tilt switch or "delay-on" timer in the control circuit (by others) to allow the damper to open prior to allowing fan operation, which will protect the damper blades and fan from damage when the fan is first energized. Electrical Accessories are available to simplify the installation and reduce the total project cost. Disconnect Switches can be shipped loose or factory mounted and wired (except explosion proof and two speed) in NEMA, R, 4X, or other enclosures. Two-speed and explosion proof disconnects are available but may be subject to more stringent code requirements. It is the responsibility of the buyer and the installer to comply with all local and national codes. Aluminum Construction is available for most models and typically includes propeller blades, fan panel, motor and drive support (large frame motors may have steel reinforcement) and accessories. When an explosion proof motor is specified, aluminum fan construction must be used for additional spark resistance. UL-705 Listing is available for sidewall propeller fans with most motors and should be specified for electrical safety and reliability. Extended Lube Lines provide convenient access for routine bearing lubrication. Lubrication lines are installed from the fan shaft bearings to the exterior of the wall housing or sheet metal motorside guard and are provided with Zerk fittings. Paints and Coatings include protective and corrosion resistant coatings such as air-dry two part epoxy, phenolic (Heresite) and synthetic resin (Eisenheiss), as well as decorative color finishes to match the building (a paint chip is required to match). Please note that our standard construction material specifications are almost exclusively G90 galvanized steel and may not require any additional coating. Mounting Angles facilitate the installation and a secure attachment of the wall housing or wall collar into the framed wall opening. Galvanized or aluminum angles are available and are pre-cut to the proper length. Additional bracing, mounting hardware, flashing and caulking are typically provided by the installer. Factory Wiring can simplify jobsite installation and reduce the overall project cost. Optional services include wiring of motor, disconnect switch, damper actuator, and other custom controls. Please note that some wiring options may not be available in conjunction with the UL-705 listing option (for example explosion proof, two speed and special motors). 9
additional products Jenco manufactures a complete line of gravity ventilators and fans for all your ventilation requirements. MODEL DB Backward Inclined Belt Drive Centrifugal Roof Exhaust MODEL RED Backward Inclined Direct Drive Solid State Speed Control MODEL SQB/SQD Backward Inclined Belt Drive/Direct Drive Square Inline MODEL UBB/UBX Propeller Belt and Direct Drive Upblast Roof Exhaust MODEL L Propeller Belt Drive Wall Exhaust or Supply MODEL BGH Gravity Hood Intake or Relief MODEL KSF Forward Curved Blower Belt Drive Filtered Roof Supply MODEL TXB/TXD Backward Inclined Belt Drive/Direct Drive Centrifugal Upblast MODEL BVS Backward Inclined Belt Drive Centrifugal Utility Set DUE TO CONTINUING RESEARCH JENCOFAN RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE 69 Powers Ave. Jacksonville, FL 7 p. 904.7.47 f. 904.77.8 www.jencofan.com represented by: 0